Audio Technica UniPlate AT851a, UniPlate AT851Wa Product Information

LEGEND

Roll-off

12" or more on axis (flat)

Frequency in Hertz

Response in dB

10 dB

20k

10k

5k

2k

1k

500

200100

50

Description

The AT851a is a wide-range condenser
microphone with a hemi-cardioid (half-space
cardioid) polar pattern. It is useful in surface­mounted applications such as high-quality
sound reinforcement, professional recording,
television, and other demanding sound
pickup situations. Its small size makes the
AT851a ideal for use in applications where
minimum visibility is required.

Supplied as a cardioid, the AT851a easily
accepts interchangeable elements to permit
selection of angle of acceptance from 100° to
360°. The following optional elements are
available from an authorized Audio-Technica
dealer or the A-T service department:
AT853H-ELE hypercardioid, AT853O-ELE
omnidirectional, AT853SC-ELE subcardioid.

Positioning a properly designed miniature
cardioid microphone centrally on a large, flat,
unobstructed surface yields several distinct
advantages. Directionality is increased by
3 dB, promoting enhanced gain before
feedback and further suppression of ambient
noise. Sensitivity is increased for improved
signal to noise ratio. Phase distortion due to
reflected sound energy from the boundary
itself is eliminated.

The microphone features a 25' (7.6 m) cable
with TA3F-type connectors for use between
the microphone and the AT8531 power
module provided. It can be powered from an
external 9V to 52V DC phantom power
supply or from a 1.5V AA battery. Current
demands are so low that a premium battery
will provide about 1200 hours of continuous
use. A built-in 3-position switch on the power
module allows selection of off, on/flat
response or on/low-roll-off.

The microphone element is enclosed in a
rugged die-cast case and protected by two
layers of perforated steel. The combination of
heavy die-cast case and rubber non-slip
bottom pad minimizes mechanical coupling
of surface vibrations to the microphone. The
low-profile housing has a low-reflectance
black finish. The microphone is also available
in white as the AT851Wa, with a white­finished microphone housing and cable.

Installation and Operation

To install the battery, remove the cap from
the top of the power module. Insert the
battery, being certain to observe battery
polarity as marked (+ end toward the cap
release button). For longest battery life, the
switch should remain off except when the
microphone is in use. While standard carbon­zinc AA batteries will operate the microphone
satisfactorily, alkaline or mercury cells are
preferred for longer service life. Only
“leakproof” batteries should be used. The
battery does not have to be in place to use in
phantom power mode. Phantom power
requires 9V to 52V DC.

The symmetry and area of the mounting
surface directly affect the sensitivity of the
boundary microphone at low frequencies.
Ideally, the mounting surface should be
circular; however, square or rectangular

surfaces are most often used. If the mount­ing surface is rectangular, the smaller dimen­sion tends to determine low-frequency
cutoff. The microphone should be centered
on the surface and positioned with the front
of the microphone facing the sound source
along the longer dimension of the mounting
surface. The sound source should not be
below, or higher than 60° above, the plane of
the mounting surface.

Output is low impedance balanced. The
output connector of the power module
mates with XLRF-type cable connectors. The
balanced signal appears across Pins 2 and 3,
while the ground (shield) connection is Pin 1.
Output is phased so that positive acoustic
pressure produces positive voltage at Pin 2 in
accordance with industry convention.

While a modern condenser microphone is
not unduly sensitive to the environment,
temperature extremes can be harmful. Avoid
leaving the microphone in the open sun or in
areas where temperatures exceed 110° F
(43° C) for long periods of time. Extremely
high humidity should also be avoided.

Architects and Engineers Specifications

The microphone shall be a fixed-charge
condenser with a hemi-cardioid polar pattern
designed for use in surface-mount boundary
applications. It shall be capable of accepting
optional interchangeable elements for
additional polar patterns. The frequency
response shall be 30 Hz to 20,000 Hz. The
microphone shall operate from an external 9V
to 52V DC phantom power source, or alterna­tively, from a 1.5V AA/UM3 battery. Nominal
open-circuit output voltage shall be 6.3 mV
(phantom) or 5.6 mV (battery) at 1 kHz, 1
Pascal. Output shall be low impedance
balanced (200 ohms-phantom, 270 ohms­battery).

A 25' (7.6 m) cable with TA3F connectors
shall be supplied for connection between the
microphone and the power module. The
included power module shall house the
battery and contain an off/on/low-roll-off
switch. The power module shall terminate in
a 3-pin XLRM-type connector.

The microphone shall have a maximum width
of 2.52" (64.0 mm) and maximum length of

3.60" (91.5 mm). Weight shall be 4.2 oz (120
grams). The microphone housing shall be
housed in a die-cast case with a two-layer
perforated steel grille. Finish shall be low­reflectance black [white].

The Audio-Technica AT851a [AT851Wa] is
specified.

AT851a
AT851Wa

MICRO
CARDIOID
CONDENSER
BOUNDARY
MICROPHONE

Frequency Response

60°

IDEAL
WORKING
ANGLE

AT851a
AT851Wa

Polar Pattern

Dimensions

Audio-Technica U.S., Inc., 1221 Commerce Drive, Stow, Ohio 44224
Audio-Technica Limited, Old Lane, Leeds LS11 8AG England

Form No. 0310-0855-00-B/W P50871 © 1996 Audio -Technica U.S., Inc. Printed in U.S.A.

200 Hz

1 kHz
5 kHz
8 kHz

LEGEND

SCALE IS 5 DECIBELS PER DIVISION

90

60

120

30

150

210

240

270

300

330

180

0

AT851a/AT851Wa SPECIFICATIONS

†

ELEMENT Fixed-charge back plate

permanently polarized condenser

POLAR PATTERN Half-cardioid (cardioid in hemisphere

above mounting surface)

FREQUENCY RESPONSE 30-20,000 Hz
LOW-FREQUENCY ROLL-OFF 80 Hz, 18 dB/octave
OPEN CIRCUIT SENSITIVITY PHANTOM –44 dB (6.3 mV) re 1V at 1 Pa*

BATTERY –45 dB (5.6 mV) re 1V at 1 Pa*

IMPEDANCE PHANTOM 200 ohms

BATTERY 270 ohms

MAXIMUM INPUT SOUND LEVEL PHANTOM 135 dB SPL, 1 kHz at 1% T.H.D.

BATTERY 121 dB SPL, 1 kHz at 1% T.H.D.

DYNAMIC RANGE (TYPICAL) PHANTOM 108 dB, 1 kHz at Max SPL

BATTERY 94 dB, 1 kHz at Max SPL

SIGNAL-TO-NOISE RATIO

1

67 dB, 1 kHz at 1 Pa*

SWITCH Off, on-flat, on-roll-off
BATTERY TYPE Use only “leakproof” AA/UM3 1.5V battery
BATTERY CURRENT 0.4 mA typical
BATTERY LIFE 1200 hours (alkaline battery)
PHANTOM POWER REQUIREMENTS 9-52V DC, 2 mA typical
WEIGHT

MICROPHONE 4.2 oz (120 grams)
POWER MODULE 5.2 oz (147 grams)

DIMENSIONS

MICROPHONE 2.52" (64.0 mm) max width, 3.60" (91.5 mm)

max length, 0.63" (16.0 mm) height

POWER MODULE 3.27" (83.0 mm) H x 2.48" (63.0 mm) W x

0.87" (22.0 mm) D

OUTPUT CONNECTOR (POWER MODULE) Integral 3-pin XLRM-type
CABLE 25' (7.6 m) long, 0.13" (3.2 mm) diameter,

2-conductor, shielded cable with
TA3F connectors

ACCESSORIES FURNISHED AT8531 power module; battery;

soft vinyl protective pouch

OPTIONAL INTERCHANGEABLE ELEMENTS AT853H-ELE hypercardioid (100

°)

AT853O-ELE omnidirectional (360

°)

AT853SC-ELE subcardioid (170°)

†

In the interest of standards development, A.T.U.S. offers
full details on its test methods to other industry
professionals on request.

* 1 Pascal = 10 dynes/cm

2

= 10 microbars = 94 dB SPL

1

Typical, A-weighted, using Audio Precision System One.

Optional Accessories:

• CP8201 line matching transformer
(Lo-Z to 50,000 ohms).

• AT8202 adjustable in-line attenuator for
use with low-impedance microphones.

• AT8314 2-conductor, shielded, vinyl-jacketed,
broadcast-type cable with XLRF-type
connector at microphone end, XLRM-type
connector at equipment end. Available in
10', 20', 25', 30', 50' & 100' lengths.

• CP8506 four-channel 48V phantom power
supply (AC powered).

• CP8508 single-channel 24V phantom power
supply (AC powered).

64.0 mm

2.52"

16.0 mm

0.63"

91.5 mm

3.60"

39.0 mm

1.54"

POWER MODULE

AT8531

audio-technica

MADE IN JAPAN

OFF

PUSH

3.27"

83.0 mm

2.48"

63.0 mm

22.0 mm

0.87"

SWITCH

Roll-off

Flat
Off

Push Button

To Release Cap

AT8531 Power Module

One-Year Limited Warranty

Audio-Technica microphones and accessories purchased in the U.S.A. are warranted for one year from date of purchase by
Audio-Technica U.S., Inc. (A.T.U.S.) to be free of defects in materials and workmanship. In event of such defect, product will
be repaired promptly without charge or, at our option, replaced with a new product of equal or superior value if delivered to
A.T.U.S. or an Authorized Service Center, prepaid, together with the sales slip or other proof of purchase date.

Prior approval from A.T.U.S. is required for return.

This warranty excludes defects due to normal wear, abuse, shipping
damage, or failure to use product in accordance with instructions. This warranty is void in the event of unauthorized repair
or modification.

For return approval and shipping information,

contact the Service Department, Audio-Technica U.S., Inc.,

1221 Commerce Drive, Stow, Ohio 44224.
Except to the extent precluded by applicable state law,

A.T.U.S. will have no liability for any consequential, incidental,
or special damages; any warranty of merchantability or fitness for particular purpose expires when this warranty
expires.

This warranty gives you specific legal rights, and you may have other rights which vary from state to state.

Outside the U.S.A., please contact your local dealer for warranty details.