Audio Technica T3201DE2 User Manual
3000 Series
User Manual
UHF synthesized diversity wireless system
ATW-R3210
UHF Synthesized diversity receiver
ATW-T3201
UHF transmitter
ATW-T3202
UHF transmitter
Introduction
Thank you for purchasing this Audio-Technica product.
Before using the product, read through this user manual to ensure that you will use the product correctly. Please keep this manual for future
reference.
Package contents
Before use, check to make sure that all of the following items are contained in the package.
If any of the items is missing from your package or damaged, contact your local Audio-Technica dealer.
• ATW-R3210
• ATW-T3201
• ATW-T3201
• AC adapter (for ATW-R3210)
• Rack mount (large, small)
• Screw kit for Rack mount
• AT8456a microphone holder (for ATW-T3202)
• AT8456a screws for microphone holder (for ATW-T3202)
• Antennas
• Quick Start Guide
• Warranty
Important information
Warning:
•
To prevent fire or shock hazard, do not expose this apparatus to rain or moisture.
Caution:
• Do not expose this apparatus to drips or splashes.
• To avoid electric shock, do not open the cabinet.
• Refer servicing to qualified personnel only.
•
Do not expose this apparatus to excessive heat such as sunshine, fire or the like.
• Do not subject this apparatus to strong impact.
• This apparatus should be located close enough to the AC outlet so
that you can easily grasp the AC adapter at any time.
•
Do not place any objects filled with liquids, such as vases, on this apparatus.
• To prevent fire, do not place any naked flame sources (such as
lighted candles) on this apparatus.
• Do not install this apparatus in a confined space such as a bookcase
or similar unit.
• Install this apparatus only in places with good ventilation.
• The rating label is put on the bottom of this apparatus.
Battery Caution:
• Keep batteries out of the reach of children.
• Observe correct polarity as marked.
• Do not expose the battery to excessive heat such as sunshine, fire or
the like.
• Always consider the environment issues and follow local
regulations when disposing of batteries.
• Remove depleted battery immediately.
• Danger of explosion if battery is incorrectly replaced. Replace only
with the same or equivalent type.
• Use only disposable LR06(AA) alkaline batteries.
• Do not use rechargeable batteries.
• Do not use new batteries and old one at the same time.
• Do not use different batteries type or model.
• Do not use a leaking battery. If battery leakage occurs, avoid
contact with skin. If contact occurs, immediately wash thoroughly
with soap and water.
• If contact occurs, immediately wash thoroughly with soap and
water.
• If battery leakage comes into contact with your eyes, immediately
flush with water and seek medical.
For customers in the USA
FCC Notice
Warning:
This device complies with Part 15 of the FCC Rules. Operation is
subject to the condition that this device does not cause harmful
interference.
Caution:
You are cautioned that any changes or modifications not expressly
approved in this manual could void your authority to operate this
equipment.
Note: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
For customers in Canada
IC statement
CAN RSS-Gen/CNR-Gen
This device complies with INDUSTRY CANADA R.S.S. 210. Operation
is subject to the following conditions: (1) This device may not cause
harmful interference and (2) this device must accept any interference
received, including interference which may cause undesired operation.
This device complies with RSS-102 radiation exposure limits set forth
for an uncontrolled environment.
2
Informations importantes
Avertissement:
•
Pour éviter tout risque de choc électrique ou d’incendie, n’exposez pas cet
appareil à la pluie ou à l’humidité.
Attention:
• Protégez cet appareil des projections et des gouttes d’eau.
• Confiez tous travaux d’entretien à un technicien qualifié.
• N’exposez pas cet équipement à des températures excessives, telles
que celles de la lumière directe du soleil, d’une flamme ou autres
sources de chaleur.
•
Ne soumettez pas cet équipement à de forts impacts.
• Cet appareil doit être placé à proximité de la prise secteur afin que
vous puissiez facilement vous saisir de l'adaptateur secteur à tout
moment.
• Ne placez pas d’objets remplis de liquide tels que des vases, sur
l’appareil.
• Pour éviter tout risque d’incendie, ne placez pas de flammes nues (telles
que des bougies allumées) sur l’appareil.
• N’installez pas cet appareil dans un espace confiné tel qu’une
étagère ou un endroit similaire.
• N'installez cet appareil que dans des endroits bien aérés.
• La plaque signalétique se trouve sur le dessous de cet appareil.
Mise en garde relative aux piles:
• Tenez les piles hors de portée des enfants.
• Respectez la polarité correcte indiquée.
• N'exposez pas la pile à une chaleur excessive telle que les rayons du
soleil, un feu ou autre source de chaleur.
• Prenez toujours en considération l'impact environnemental et suivez
les réglementations locales lors de la mise au rebut des piles.
• Retirez immédiatement toute pile déchargée.
• Danger d'explosion en cas de positionnement incorrect de la
pile. Remplacez uniquement avec des piles de type identique ou
équivalent.
• Utilisez uniquement des piles alcalines LR06 (AA) jetables.
• N'utilisez pas des piles rechargeables.
• Ne mélangez pas des piles neuves et des piles usagées.
• Ne mélangez pas différents types ou modèles de piles.
• N'utilisez pas une pile qui fuit. En cas de fuite de la pile, évitez tout
contact avec la peau.
• En cas de contact, rincez aussitôt abondamment au savon et à
l'eau.
• Si le liquide de la pile entre en contact avec vos yeux, lavez aussitôt
avec de l'eau et consultez un médecin.
Pour les clients aux États-Unis
Avis de la FCC
Avertissement:
Cet appareil est conforme à la Partie15 du règlement de la FCC. Son
fonctionnement est soumis aux deux conditions suivantes: (1) Cet
appareil ne doit pas causer d’interférence nocive et (2) cet appareil doit
accepter les interférences reçues, y compris les interférences pouvant
provoquer un fonctionnement indésirable.
Attention:
Vous êtes averti que tout changement ou modification non
expressément approuvé dans ce manuel est susceptible d’annuler
votre droit d’utilisation de cet appareil.
Note: Cet appareil a fait l’objet de tests afin de vérifier sa conformité
avec les limites relatives aux appareils numériques de classe B,
conformément à la partie 15 du règlement de la FCC. Ces limites
ont pour vocation d’offrir une protection raisonnable contre les
interférences nocives en installation résidentielle. Cet appareil génère,
utilise et peut émettre des fréquences radioélectriques et provoquer,
en cas d’installation et d’utilisation non conformes aux instructions,
des interférences préjudiciables à la réception des signaux radio.
Toutefois, il n’y a pas de garantie que des interférences ne se
produiront pas dans une installation particulière. Si l’appareil provoque
des interférences préjudiciables à la réception radio ou télévisée, ce qui
peut être déterminé en éteignant et allumant l’appareil, l’utilisateur est
invité à essayer d’y remédier en prenant une ou plusieurs des mesures
suivantes:
- Réorienter ou déplacer l’antenne réceptrice.
- Augmenter la séparation entre l’appareil et le récepteur.
- Brancher l’appareil dans une prise, sur un circuit différent de celui
auquel est raccordé le récepteur.
- Demander de l’aide au revendeur ou à un technicien radio/TV qualifié.
À l’attention des clients au Canada
Déclaration IC
CAN RSS-Gen/CNR-Gen
Cet appareil est conforme à la norme R.S.S. 210 d'INDUSTRIE
CANADA. Le fonctionnement est soumis aux conditions suivantes:
(1) Cet appareil ne doit pas causer d'interférences dommageables
et (2) cet appareil doit accepter toutes les interférences reçues, y
compris les interférences susceptibles de générer un fonctionnement
préjudiciable.
Cet appareil est conforme aux limites de RSS-102 sur l'exposition aux
rayonnements établies pour un environnement non contrôlé.
3
Safety precautions
• When using the product, also read the user manuals supplied with the devices that are to be connected.
• When not using the product, remove the power plug from the power outlet.
• Turn the product off before connecting or disconnecting cables.
• If you use the product near a TV or radio antenna, noise may be generated in the TV or radio. In this case, move the product away from the TV or
radio antenna.
• Two transmitters on the same frequency cannot be used simultaneously.
• Please be aware that interference may be generated from the surrounding electromagnetic environment and/or from using multiple units.
• The wireless system may be affected by electromagnetic noise from automobile spark plugs, light dimmers, computers, OA devices, or electrical
music instruments. Position the components of the system in a place where it is less likely to be affected.
• Only use this product in combination with devices specified by the manufacturer.
• Insert the plugs of connecting cables securely into their mating connectors.
• Radio waves in the UHF band propagate mainly by line of sight. Configure system so there are no obstructions between
the transmitter and receiver.
• Turn the phantom power off when connecting to the mixer.
• Use 120 V AC power source. Refer to "Specifications" for product ratings.
• If there is an electronic device or a transmitter (mobile phone etc.) in the vicinity of this product, this product may be subject to noise. In this case,
move the product away from the devices.
• When installing this product, make sure there are no obstacles between the receiver and the transmitter that block radio waves.
• If you use the product near a TV or radio antenna, noise may be generated in the TV or radio. In this case, move the product away from the devices.
• To prevent the batteries from wearing out, turn the product off when not in use.
• Over time, discoloration may occur due to ultraviolet rays (especially direct sunlight) and friction.
• Any customization of the product is prohibited by law. Also, disassembly of the product may result in electrical shock, equipment damage or fire.
Never disassemble the product.
Care
• If the product becomes dirty or dusty, disconnect the power plug first, and then wipe the product off with a dry soft cloth.
• Do not use benzine, thinner, contact restoring protective agent, or any other chemical agent. Doing so may cause deformation, damage, or
malfunction.
• When storing the product for an extended period of time, wrap it with a plastic cover, and do not allow it to be exposed to humidity.
4
Part names and functions
ATW-R3210
Front panel
❷❶ ❹ ❺❸
Power switch ( )
❶
Press the switch to turn the power on.
IR sync window
❷
Use when syncing transmitter (ATW-T3201/ATW-T3202) to the product.
Display
❸
Displays the product state and setting menus.
BACK button
❹
Takes the display back one screen when pressed.
Control dial
❺
Turn to scroll through settings and press to set them.
5
Part names and functions
Rear panel
Antenna input jack
❶
Attach the antenna directly, or extend it with a low-loss antenna cable.
Unbalanced output jack (6 3 mm (1/4"))
❷
Balanced output jack (XLR 3-pin male)
❸
❺❸❷ ❹❶
GND
Ground lift switch
❹
This switch isolates the GND pin of the balanced output from the ground.
Normally use in the GROUND position, but if a hum develops due to a ground loop, switch to the "GROUND LIFT" side.
Power input jack
❺
Connect the DC plug from the included AC adapter for 12 V, 1 A.
HOT
COLD
6
Part names and functions
ATW-T3201
❶
❷
❸
❻
❼
❺
❹
❽
❾
❿
⓫
⓬
⓮
⓯
Transmission antenna
❶
MUTE switch
❷
Press to switch audio mute on and off.
Indicator
❸
Indicates status of power supply or battery by LED.
Power ON: lights in green
Low battery: lights in red
• Lits once when RECALL/Multi function button is pressed and
hold.
RECALL/Multi function button
❹
Press to turn the screen back on if it shuts off. Press and hold to
perform the assigned action.
Microphone input connector
❺
Connect a microphone (sold separately).
Display
❻
Shows the current status.
• If no buttons are pressed for a period of 30 seconds, the display
will turn off.
SYNC button
❼
Use when syncing receiver (ATW-R3210) to the product.
⓭
⓰
UP button
❽
Used for selecting various settings.
BACK button
❾
Returns to the previous operation.
Power switch
❿
Turns the power on/off.
SET button
⓫
Press to confirm a selection.
DOWN button
⓬
Used for selecting various settings.
Battery cover
⓭
Technical standard conformity certification sticker
⓮
Using the product without this sticker may cause legal violation.
Do not peel off.
IR sync window
⓯
Use when syncing the product to the receiver.
Charging terminals
⓰
7
Loading...