Audio Technica PRO 3x Specifications

• Designed for close-up vocal and instrumental use

• Dependable long life and consistent high quality

• Two-stage ball-type screen reduces wind noise and “popping”
during close use

• Cardioid polar pattern reduces pickup of sounds from the sides
and rear, improving isolation of desired sound source

Output from the microphone’s XLRM-type connector is low
impedance (Lo-Z) balanced. The signal appears across Pins 2
and 3; Pin 1 is ground (shield). Output phase is “Pin 2 hot” –
positive acoustic pressure produces positive voltage at Pin 2.

Plug Type Ground Audio “+” Audio “–”

XLR Pin 1 Pin 2 Pin 3
1/4" “TRS” Slee v e Tip Ring
1/4" Sleeve Tip Sleeve

To avoid phase cancellation and poor sound, all mic cables must
be wired consistently: Pin 1-to-Pin 1, etc. For a high-impedance
(Hi-Z) mic input, connect a Low-Z balanced cable to a Hi-Z match­ing transformer (A-T CP8201 or equal) at the equipment input.

When using the PRO 3x in settings with a stage monitor speaker,
the speaker should be located 180° off axis (at the rear of
the microphone). This placement, in conjunction with the
microphone’s uniform cardioid pickup patter n, will virtually
eliminate the possibility of undesired audio feedback.

The high sensitivity of the PRO 3x assures useful output and an
excellent match to most input sources. In some cases, however,
an attenuator such as the Audio-Technica AT8202 may be
required between the microphone and preamplifier to avoid
overloading sensitive input stages.

Take care to keep foreign particles from entering the windscreen.
An accumulation of iron or steel filings on the diaphragm, and/or
foreign material in the windscreen’s mesh surface, can degrade
performance.

One-Year Limited Warranty

Audio-Technica brand products purchased in the U.S.A.are warranted for one year from date
of purchase by Audio-Technica U.S., Inc.(A.T.U.S.) to be free of defects in materials and
workmanship. In event of such defect, product will be repaired promptly without charge or, at
our option, replaced with a new product of equal or superior value if delivered to A.T.U.S.or
an Authorized Service Center, prepaid, together with the sales slip or other proof of purchase
date. Prior approval from A.T.U.S. is required for return. This warranty excludes defects
due to normal wear, abuse, shipping damage, or f ailure to use product in accordance with
instructions. This warranty is void in the ev ent of unauthorized repair or modification, or
removal or defacing of the product labeling.

For return approval and shipping information,contact the Service Department,
Audio-Technica U.S., Inc., 1221 Commerce Drive, Stow, Ohio 44224.

Except to the extent precluded by applicable state law, A.T.U.S. will have no liability for

any consequential, incidental, or special damages; any warranty of merchantability or
fitness for particular purpose expires when this warranty expires.

This warranty gives you specific legal rights, and you ma y have other rights which vary from
state to state.

Outside the U.S.A., please contact your local dealer for warranty details.

PRO3x SPECIFICATIONS

†

ELEMENT Dynamic
POLAR PATTERN Cardioid (Unidirectional)
FREQUENCY RESPONSE 90-13,000 Hz
OPEN CIRCUIT SENSITIVITY –55 dB (1.7 mV) re 1V at 1 Pa*
IMPEDANCE 500 ohms
SWITCH On/off
WEIGHT (less cable and clamp) 9.5 oz (270 g)
DIMENSIONS 6.79" (172.5 mm) long, 2.08"

(52.8 mm) head diameter, 1.25"
to 0.88" (31.8 mm to 22.4 mm)
tapered body diameter

OUTPUT CONNECTOR Integral 3-pin XLRM-type
CABLE 15.0' (4.5 m) 2-conductor,

shielded, vinyl-jacketed,
broadcast-type cable with
XLRF-type connector at
microphone end, XLRM-type
connector at equipment end

ACCESSORY FURNISHED Stand clamp for 5/8"-27

threaded stands

†

In the interest of standards development, A.T.U.S. offers full details on its test
methods to other industry professionals on request.

*1 Pascal = 10 dynes/cm

2

= 10 microbars = 94 dB SPL

Audio-Technica U.S., Inc., 1221 Commerce Drive, Stow, Ohio 44224

Audio-Technica Limited, Old Lane, Leeds LS11 8AG England

www.audio-technica.com

P51242-EN ©2000 Audio -Technica U.S., Inc. Printed in Philippines

PRO

3x

CARDIOID DYNAMIC MICROPHONE

12" or more on axis

LEGEND

10 dB

Response in dB

20k

10k

5k

2k

500

200

1k

Frequency in Hertz

50 100

Frequency Response

Polar Pattern

SCALE IS 5 DECIBELS PER DIVISION

200 Hz

1 kHz
5 kHz
8 kHz

90°

60°

120°

30°

150°

210°

240°

270°

300°

330°

180°

0°

LEGEND