Audio-Technica PRO 35cH Specifications

SCALE IS 5 DECIBELS PER DIVISION

Polar Pattern

200 Hz

LEGEND

5 kHz

1 kHz

8 kHz

12" or more on axis

LEGEND

Roll-off

Frequency in Hertz

Frequency Response

Response in dB

PRO35

CARDIOID CONDENSER CLIP-ON INSTRUMENT MICROPHONE

• Ideal for sax, toms, brass and percussion

• Excels in high-SPL applications

• Perfect for active stage performances

• Extended frequency response captures subtle nuances of the performance

• UniMount

clip permits accurate positioning, provides shock

resistance and protects element

PRO 35 SPECIFICATIONS ELEMENT Fix

POLAR P FREQUENCY RESPONSE 50-15,000 Hz LOW FREQUENCY ROLL-OFF 80 Hz, 18 dB/octave OPEN CIRCUIT SENSITIVITY – IMPED MAXIMUM INPUT SOUND LEVEL 145 dB SPL, 1 kHz at 1% D SIGNAL-T PHANTOM POWER REQUIREMENTS 11-52V DC, 2 mA typical SWITCH Flat, roll-off WEIGHT (less cab

DIMENSIONS

OUTPUT CONNECT

(power module)

CABLE 6.0' (1.8 m) long (per

ACCESSORIES FURNISHED AT8418 UniMount®microphone

†

*1 Pascal = 10 dynes /cm

Specifications are subject to change without notice.

ATTERN

ANCE

YNAMIC RANGE

O-NOISE RATIO

OPHONE

MICR POWER MODULE 2.9 oz (81 g)

OPHONE

MICR

WER MODULE

In the interest of standards development, A.T.U.S.offers full details on its test methods to other industry professionals on request.

Typical, A-weighted, using Audio Precision System One.

†

(typical)

le and accessories)

= 10 microbars = 94 dB SPL

ed-charge back plate

manently polarized condenser

per Cardioid

45 dB (5.6 mV) re 1V at 1 Pa*

250 ohms

115 dB, 1 kHz at Max SPL

,1 kHz at 1 Pa*

64 dB

0.3 oz (8 g)

0.98" (25.0 mm) long,

0.40" (10.2 mm) diameter

3.66" (92.9 mm) long,

0.74" (18.9 mm) diameter ral 3-pin XLRM-type

Integ

attached to microphone),

0.10" (2.6 mm) diameter,

2-conductor

A3F-type connector

ument mount; AT8538 power

instr

soft protective pouch

module;

manently

, shielded cable with

THD

• Corrosion-resistant contacts from gold-plated XLRM-type connector

• Cardioid polar pattern reduces pickup of sounds from the sides and rear, improving isolation of desired sound source

The PRO 35 is intended for use in professional applications where remote power is available. It requires 11V to 52V DC phantom power, which may be provided by a mixer or console, or

y a separate, in-line source such as the Audio-Technica AT8801

b single-channel or CP8506 four-channel phantom power supplies.

An integ frequency response to a lo

ral 80 Hz high-pass filter provides easy switching from a flat

w-end roll-off. The roll-off position reduces the pickup of low-frequency ambient noise (such as traffic, air-handling systems, etc.), room reverberation and mechanically coupled vibr

ations.

Output from the power module’s XLRM-type connector is low impedance (Lo-Z) balanced. The signal appears across Pins 2 and 3;

Pin 1 is ground (shield). Output phase is “Pin 2 hot” – positive

acoustic pressure produces positive voltage at Pin 2.

o avoid phase cancellation and poor sound, all mic cables must be

wired consistently:

ving the microphone in the open sun or in areas where

oid lea

Pin 1-to-Pin 1, etc.

temperatures exceed 110° F (43° C) for extended periods.

oided.

Extremely high humidity should also be a

Audio-Technica U.S., Inc., 1221 Commerce Drive, Stow, Ohio 44224

echnica Limited,

Audi

Old Lane, Leeds L

1 8AG England

www.audio-technica.com