Audio-Technica ES947 Specifications

8 kHz

Polar Pattern

SCALE IS 5 DECIBELS PER DIVISION

LEGEND

200 Hz

1 kHz 5 kHz

Frequency in Hertz

LEGEND

12" or more on axis

Frequency Response

Response in dB

ES947

1.18"

30.0 mm

DESIGNATES

FRONT OF MIC

1.02"

26.0 mm

0.33"

8.5 mm

2.72"

69.0 mm

NUT

0.79"

20.0 mm

ISOLATORS

TABLE

CARDIOID CONDENSER BOUNDARY MICROPHONE

DESCRIPTION

The ES947 is a wide-range condenser microphone with a unidirectional polar pattern. It is designed for unobtrusive table, ceiling or panel-mounted applications for high-quality sound reinforcement, teleconferencing, professional recording, television and other demanding sound pickup applications.

The ES947 is equipped with UniGuard

™

RFI-shielding technology, which offers outstanding rejection of radio frequency interference (RFI).

The microphone should be placed on a flat, unobstructed mounting surface. The smalldiameter capsule near the boundary eliminates phase

distortion and delivers clear, high-output performance.

The microphone requires 11V to 52V phantom power for operation. The microphone is enclosed in a heavy-duty die-cast case and protected by a two-layer steel mesh grille. The low-profile housing has a low-reflectance black finish. The microphone is also available in white as the ES947W. Isolators are included with the microphone for optional mechanical isolation from the mounting surface.

INSTALLATION AND OPERATION

Output is low impedance balanced. The balanced signal appears across Pins 2 and 3, while the ground (shield) connection is Pin 1. Output is phased so that positive acoustic pressure produces positive voltage at Pin 2 in accordance with industry convention.

ES947 SPECIFICATIONS

ELEMENT Fixed-charge back plate

POLAR PATTERN Unidirectional (Cardioid in

FREQUENCY RESPONSE 40-12,000 Hz

OPEN CIRCUIT SENSITIVITY –42 dB (7.9 mV) re 1V at 1 Pa*

IMPEDANCE 200 ohms

MAXIMUM INPUT SOUND LEVEL 142 dB SPL, 1 kHz at 1% T.H.D.

DYNAMIC RANGE (typical) 113 dB, 1 kHz at Max SPL

SIGNAL-TO-NOISE RATIO

PHANTOM POWER REQUIREMENTS 11-52V DC, 2 mA typical

WEIGHT 64 g (2.3 oz)

DIMENSIONS 30.0 mm (1.18") diameter,

OUTPUT CONNECTOR Integral 3-pin XLRM-type

ACCESSORY FURNISHED One pair isolators

†In the interest of standards development, A.T.U.S. offers full details on its test

methods to other industry professionals on request.

*1 Pascal = 10 dynes/cm

Typical, A-weighted, using Audio Precision System One.

Specifications are subject to change without notice.

†

= 10 microbars = 94 dB SPL

permanently polarized condenser

hemisphere above mounting surface)

65 dB, 1 kHz at 1 Pa*

69.0 mm (2.72") length

To mount the ES947 in a ceiling or table top

without the isolators,

a 13⁄16" (20.5 mm) diameter hole is required. To mount the ES947

with the isolators, a 15⁄16" (23.5 mm) hole is required. Place the isolators on either side of the hole to achieve mechanical isolation from the mounting surface. The small indented circle on the ES947 bezel indicates the “front” of the microphone.

While a modern fixed-charge condenser microphone is not unduly sensitive to the environment, temperature extremes can be harmful. Exposure to high temperature can result in gradual and permanent reduction of the output level. Avoid leaving the microphone in the open sun or in areas where temperatures exceed 110° F (43° C) for long periods of time. Extremely high humidity should also be avoided.

ARCHITECTS AND ENGINEERS SPECIFICATIONS

The microphone shall be a fixed-charge condenser designed for use in table, ceiling or panel-mount boundary applications. It shall have a frequency response of 40 Hz to 12,000 Hz and a unidirectional (cardioid in a hemisphere above the mounting surface boundary) polar pattern. It shall incorporate a self-contained power module and require 11-52V DC phantom power to operate. It shall offer outstanding rejection of radio frequency interference (RFI). It shall be capable of handling sound input levels up to 142 dB with a dynamic range of 113 dB. Nominal open circuit output voltage shall be 7.9 mV at 1 kHz, 1 Pascal. Output shall be low impedance balanced (200 ohms) from an integral 3-pin XLRM-type connector.

The microphone shall have a maximum diameter of 30.0 mm (1.18") and an overall length of 69.0 mm (2.72"). Weight shall be 64 grams (2.3 oz). The microphone shall be housed in an all-metal case with a two-layer steel mesh grille. Finish shall be low reflectance black [white]. A small indented circle on the bezel shall indicate the “front” of the microphone. Resilient isolators shall be provided for reduction of mechanical noise transfer from the mounting panel. The Audio-Technica ES947 [ES947W] is specified.

Audio-Technica U.S., Inc., 1221 Commerce Drive, Stow, Ohio 44224

Audio-Technica Limited, Old Lane, Leeds LS11 8AG England

www.audio-technica.com