Audio Technica Engineered Sound AT961R, Engineered Sound AT961RP Product Information

Description

The AT961R and AT961RP are wide-range
condenser microphones with unidirectional polar
patterns.They are designed for surface-mounted
applications such as high-quality sound reinforce­ment, professional recording, television, and
teleconferencing.

Positioning a properly designed unidirectional
microphone centrally on a large, flat, unobstructed
surface yields several distinct advantages.The
directionality is increased by 3 dB, promoting
enhanced gain before feedback and further sup­pression of ambient noise. Sensitivity is increased
for improved signal to noise ratio. Phase distortion
due to reflected sound energy from the boundary
itself is eliminated.

The AT961R and AT961RP require 9V to
52V DC phantom power for operation.A built-in
2-position switch allows selection of flat or low­roll-off response. Enclosed in a rugged die-cast
case and protected by two layers of sturdy
perforated steel, each microphone has a field­replaceable element and low-reflectance black
finish.The microphones are also available in white,
as AT961RW and AT961RWP.The combination
of heavy case and rubber non-slip bottom pad
minimizes mechanical coupling of surface
vibrations to the microphone.

The AT961R is supplied with a 25' (7.6 m)
output cable terminating in TA3F and
XLRM-type connectors.

The AT961RP has a 3- conductor (“stereo” )

1

/4" phone plug built into its underside, allowing

for quick and easy mounting and removal.

Installation and Operation

The symmetry and area of the mounting
surface directly affect the sensitivity of the
boundary microphone at low frequencies.
Ideally, the mounting surface should be circular;
however, square or rectangular surfaces are
most often used. If the mounting surface is
rectangular, the smaller dimension tends to
determine low-frequency cutoff.The microphone
should be centered on the surface and posi­tioned with the front of the microphone facing
the sound source along the longer dimension of
the mounting surface.The sound source should
not be below, or higher than 60° above, the
plane of the mounting surface.

AT961R The AT961R’s output is low imped­ance balanced.The balanced signal appears
across Pins 2 and 3, while the ground (shield)
connection is Pin 1. Output is phased so that
positive acoustic pressure produces positive
voltage at Pin 2 in accordance with industry
convention.

The AT961R can be mounted to a flat
surface using two panhead screws in conjunc­tion with the keyhole slots on the microphone’s

underside. Simply remove the small cut-out
section of the rubber pad to reveal the keyhole
slots and the low-frequency roll-off switch.

AT961RP The AT9 61RP’s output is low imped­ance balanced.The balanced signal appears
across the tip and ring of the

1

/4" plug, while the

ground connection is to the plug’s sleeve. Output
is phased so that positive acoustic pressure
produces positive voltage at the plug’s tip.

The AT961RP can be plugged directly into

a mating 3-conductor

1

/4" jack, which can be

installed in the mounting surface.

While a modern condenser microphone
is not unduly sensitive to the environment,
temperature extremes can be harmful. Avoid
leaving the microphone in the open sun or in
areas where temperatures exceed 110° F (43° C)
for long periods of time. Extremely high humidity
should also be avoided.

Architects and Engineers Specifications

AT961R [AT961RW] The microphone shall be

a fixed-charge condenser with a unidirectional
polar pattern designed for use in surface-mount
boundary applications. The frequency response
shall be 30-20,000 Hz. The microphone shall
operate from an external 9V to 52V phantom
power source.Nominal open-circuit voltage
shall be 22.4 mV at 1 kHz, 1 Pascal. Output
shall be low impedance balanced (200 ohms).
The microphone shall include a switch for
low-frequency roll-off.

A 25' cable with TA3F to XLRM-type
connectors shall be supplied for connection
between the microphone and electronics input.

The microphone shall have a maximum width
of 2.87" (73.0 mm) and a maximum length of

3.59" (91.3 mm).Weight shall be 5.1 oz (145
grams).The microphone shall be housed in
a die-cast case with a two-layer perforated
steel grille.Finish shall be low-reflectance
black [white].

The Audio-Technica AT 9 61R [AT961RW] is

specified.
AT961RP [AT961RWP] The microphone shall

be a fixed-charge condenser with a unidirectional
polar pattern designed for use in surface-mount
boundary applications. The frequency response
shall be 30-20,000 Hz. The microphone shall
operate from an external 9V to 52V phantom
power source.Nominal open-circuit voltage
shall be 22.4 mV at 1 kHz, 1 Pascal. Output
shall be low impedance balanced (200 ohms).
The microphone shall include a switch for
low-frequency roll-off.

The microphone shall have a 3-conductor

1

/4"

plug mounted on the bottom at a right angle to
serve as an output connector.

The microphone shall have a maximum width

of 2.87" (73.0 mm) and a maximum length of

3.59" (91.3 mm).Weight shall be 5.2 oz (148
grams).The microphone shall be housed in a
die-cast case with a two-layer perforated steel
grille. Finish shall be low-reflectance black
[white].

The Audio-Technica AT 9 61RP [AT961RWP]

is specified.

AT961R

AT961RP

Unidirectional
Condenser
Boundary
Microphones

60°

IDEAL
WORKING
ANGLE

200 Hz

1 kHz
5 kHz
8 kHz

LEGEND

SCALE IS 5 DECIBELS PER DIVISION

90

60

120

30

150

210

240

270

300

330

180

0

AT961R/AT961R

P

One-Year Limited Warranty

Audio-Technica microphones and accessories purchased in the U.S.A. are warranted for one year from date of
purchase by Audio-Technica U.S., Inc. (A.T. U.S.) to be free of defects in materials and workmanship.In event of
such defect, product will be repaired promptly without charge or, at our option, replaced with a new product of
equal or superior value if delivered to A.T.U.S. or an Authorized Service Center, prepaid, together with the sales
slip or other proof of purchase date.

Prior approval from A.T.U.S.is required for return.

This warranty
excludes defects due to normal wear, abuse, shipping damage, or failure to use product in accordance with
instructions.This warranty is void in the event of unauthorized repair or modification.

For return approval and shipping information,

contact the Service Department, Audio -Technica U.S., Inc.,

1221 Commerce Drive, Stow, Ohio 44224.
Except to the extent precluded by applicable state law,

A.T.U.S.will have no liability for any consequential,
incidental, or special damages; any warranty of merchantability or fitness for particular purpose
expires when this warranty expires.

This warranty gives you specific legal rights, and you may have other rights which vary from state to state.

Outside the U.S.A., please contact your local dealer for warranty details.

Form No.03 0 9- 9215 -01-B/W P50899

© 1996 Audio-Technica U.S., Inc. Printed in U.S.A.

AT961R and AT961RP Specifications

†

Element Fixed-charge back plate permanently polarized condenser
Polar Pattern

Half-cardioid (cardioid in hemisphere above mounting surface)

Frequency Response 30-20,000 Hz
Low-frequency Roll-off 150 Hz, 6 dB/octave
Open Circuit Sensitivity –33 dB (22.4 mV) re 1V at 1 Pa*
Impedance 200 ohms
Maximum Input Sound Level 130 dB SPL, 1 kHz at 1% T.H.D.
Dynamic Range (Typical) 103 dB, 1 kHz at Max SPL
Signal-to-noise Ratio

1

67 dB, 1 kHz at 1 Pa*

Switch Flat response, low-roll-off
Phantom Power Requirements 9- 52V DC, 2 mA typical
Weight AT961R 5.1 oz (145 grams)

AT961RP 5.2 oz (148 grams)

Dimensions 3.59" (91.3 mm) maximum length

2.87" (73.0 mm) maximum body width

Output Connector AT961R TB3M

AT961RP 3-conductor 1/4" (6.3 mm) plug

Cable AT961R 25' (7.6 m) long, 0.13" (3.2 mm) diameter cable

terminating in TA3F and XLRM-type connectors

AT961RP None

Accessory Furnished Soft protective carrying case

†

In the interest of standards development, A.T.U.S. offers full details
on its test methods to other industry professionals on request.

* 1 Pascal = 10 dynes/ cm

2

= 10 microbars = 94 dB SPL

1

Typical, A-weighted, using Audio Precision System One.

Audio-Technica U.S.,Inc., 1221 Commerce Drive, Stow, Ohio 44224

Audio-Technica Limited, Old Lane, Leeds LS11 8AG England

audio-technica

73.0 mm

2.87"

91.3 mm

3.59"

2.09"

53.0 mm

16.0 mm

0.63"

53.0 mm

16.0 mm

0.63"

91.3 mm

2.09"

audio-technica

3.59"

2.87"

73.0 mm

1.22"

31.0 mm

36.5 mm

1.44"

71.8 mm

2.83"

LEGEND

Roll-off

12" or more on axis (flat)

Frequency in Hertz

Response in dB

10 dB

20k

10k

5k

2k

1k

500

200100

50

AT961R

AT961RP

Frequency Response

Screw-mount Template

(Actual Size)

Polar Pattern

1.88"

47.8 mm

0.94"

23.9 mm

2.00"

50.8 mm

Final position,
front edge of mic

C

L