Audio-Technica AT8015 Datasheet
AT8015
Line + Gradient Condenser Microphone
broadcast & production microphones
Output is low impedance (Lo-Z) balanced. The signal appears across Pins
2 and 3; Pin 1 is ground (shield). Output phase is “Pin 2 hot”— positive
acoustic pressure produces positive voltage at Pin 2.
To avoid phase cancellation and poor sound, all mic cables must be wired
consistently: Pin 1-to-Pin 1, etc.
An integral 80 Hz high-pass lter provides easy switching from a at
frequency response to a low-end roll-off. The roll-off position reduces
the pickup of low-frequency ambient noise (such as trafc, air-handling
systems, etc.), room reverberation and mechanically coupled vibrations.
To engage the high-pass lter, use the end tip of a paperclip or other
small pointed instrument to slide the switch toward the “bent” line.
Avoid leaving the microphone in the open sun or in areas where
temperatures exceed 110° F (43° C) for extended periods. Extremely high
humidity should also be avoided.
Features
• Designed for video production and broadcast (ENG/EFP) audio
acquisition
• Provides the narrow acceptance angle desirable for long-distance
sound pickup
• Smooth, natural-sounding on-axis audio quality
• Offers the convenience of battery or phantom power operation
• Rugged design and construction for reliable performance
• Switchable 80 Hz high-pass lter minimizes pickup of undesired
low-frequency sounds
Description
The AT8015 is a xed-charge condenser microphone with a line +
gradient polar pattern. It is designed for video production, broadcast
(ENG/EFP) audio acquisition, wildlife recording and high-quality sound
reinforcement.
The microphone requires 11V to 52V phantom power or a 1.5V AA
battery for operation. A battery need not be in place for phantom power
operation.
The microphone's highly directional polar pattern provides a narrow
acceptance angle along with crisp, intelligible audio reproduction
desirable for long-distance sound pickup.
The output of the microphone is a 3-pin XLRM-type connector.
A switch permits choice of at response or low-frequency roll-off (via
integral 80 Hz high-pass lter) to help control undesired ambient noise.
The microphone is enclosed in a rugged housing. The included AT8405a
stand clamp permits mounting on any microphone stand with 5/8"-27
threads. A windscreen, two o-rings, a battery and a protective carrying
case are also included.
Note: To use the microphone with a camera-mount microphone holder
whose diameter is too large to secure the microphone, slide the two
supplied o-rings onto the microphone handle, spaced so that one ts
just in front of, and the other ts just behind, the rubber nubs inside the
microphone holder. When the top of the microphone holder is closed and
tightened down, the o-rings should hold the microphone securely in place.
Architect’s and Engineer’s Specications
The microphone shall be a xed-charge condenser. It shall have a line +
gradient polar pattern and a frequency response of 40 Hz to 20,000 Hz.
The microphone shall operate from an external 11V to 52V DC phantom
power source, or, alternatively, from a 1.5V AA/UM3 battery. It shall be
capable of handling sound input levels up to 132 dB (phantom) or 120 dB
(battery) with a dynamic range of 110 dB (phantom) or 98 dB (battery).
Nominal open circuit output voltage shall be 12.5 mV (phantom) or 11.2
mV (battery) at 1 V, 1 Pascal. Output shall be low impedance balanced
(250 ohms – phantom, 300 ohms – battery).
The output of the microphone shall be a 3-pin XLRM-type output
connector.
The microphone shall include a switch that permits choice of at
response or 80 Hz low-frequency roll-off.
The microphone shall be 460.0 mm (18.11") long and have a diameter
of 21.0 mm (0.83"). Weight shall be 195 grams (6.9 oz). The microphone
shall include a stand clamp, a windscreen, two o-rings, a battery and a
protective carrying case.
The Audio-Technica AT8015 is specied.
Operation and Maintenance
The AT8015 requires 11V to 52V phantom power or a 1.5V AA battery for
operation. A battery need not be in place for phantom power operation.
To install the battery, unscrew the lower section of the microphone body,
just below the nameplate. Insert a fresh 1.5V AA battery in the handle
compartment (“+” end up), then reassemble the microphone. Alkaline
batteries are recommended for longest life. Remove the battery during
long-term storage.
Specications
Element
Polar pattern
Frequency response
Low frequency roll-off
Open circuit sensitivity
Impedance
Maximum input sound level
Dynamic range (typical)
Signal-to-noise ratio1
Phantom power requirements
Battery type
Battery current / life
Switch(es)
Weight
Dimensions
Output connector
Audio-Technica case style
Accessories furnished
In the interest of standards development, A.T.U.S.
offers full details on its test methods to other industry
*1 Pascal = 10 dynes/cm
1
Typical, A-weighted, using Audio Precision System One.
Specications are subject to change without notice.
professionals on request.
2
= 10 microbars = 94 dB SPL
AT8015
Fixed-charge back plate, permanently
polarized condenser
Line + gradient
40-20,000 Hz
80 Hz, 18 dB/octave
Phantom: –38 dB (12.5 mV) re 1V at 1 Pa
Battery: –39 dB (11.2 mV) re 1V at 1 Pa
Phantom: 250 ohms
Battery: 300 ohms
Phantom: 132 dB SPL, 1 kHz at 1% T.H.D.
Battery: 120 dB SPL, 1 kHz at 1% T.H.D.
Phantom: 110 dB, 1 kHz at Max SPL
Battery: 98 dB, 1 kHz at Max SPL
72 dB, 1 kHz at 1 Pa
11-52V DC, 2 mA typical
1.5V AA/UM3
0.4 mA / 1200 hours typical (alkaline)
Flat, roll-off
195 g (6.9 oz)
460.0 mm (18.11") long,
21.0 mm (0.83") diameter
Integral 3-pin XLRM-type
SG3
AT8405a stand clamp for
ed stands; 5/8"-27 to 3/8"-16 threaded
adapter; AT8135 windscreen; battery;
two o-rings; protective carrying case
5
/8"-27 thread-
frequency response: 40–20,000 Hz
10 dB
100
12" or more on axis
Roll-off
330˚
200
Frequency in Hertz
0˚
180˚
500
30˚
150˚
5k
2k
1k
60˚
120˚
10k
90˚
LEGEND
200 Hz
1 kHz
5 kHz
8 kHz
50
LEGEND
polar pattern
300˚
270˚
240˚
210˚
SCALE IS 5 DECIBELS PER DIVISION
Audio-Technica Corporation
audio-technica.com ©2016 Audio-Technica 0001-0193-02
Response in dB
20k
Loading...