Audio-Technica AE3300, AE4100 Datasheet
AE3000
Cardioid Condenser Instrument Microphone
Features
• Excels in high-SPL applications such as guitar cabinets, toms,
snare, timpani and overheads
• Large-diaphragm capsule combines with the open architecture of
the headcase to provide an extremely accurate and open sound
• Low-prole side-address design with tapered grille allows optimal
positioning of element vis-à-vis sound source
• Cardioid polar pattern reduces pickup of sounds from the sides
and rear, improving isolation of desired sound source
• Robust all-metal design for enduring dependability on the road
• Isolation clamp provides secure mounting, versatile positioning,
and effective dampening of unwanted mechanical noise
• Integral 80 Hz high-pass lter switch and 10 dB pad switch
artist elite® live sound microphones
frequency response to a low-end roll-off. The roll-off position reduces
the pickup of low-frequency ambient noise (such as trafc, air-handling
systems, etc.), room reverberation and mechanically coupled vibrations.
To engage the high-pass lter, slide the switch toward the “bent” line.
The microphone is also equipped with a switchable 10 dB pad that lowers
the microphone’s sensitivity, thus providing higher SPL capability for
exible use with a wide range of users and system congurations. To
engage the 10 dB pad, slide the switch toward the -10 position.
Avoid leaving the microphone in the open sun or in areas where
temperatures exceed 110° F (43° C) for extended periods. Extremely high
humidity should also be avoided.
Architect’s and Engineer’s Specications
The microphone shall be a xed-charge condenser. It shall have a cardioid
polar pattern with a uniform 120° angle of acceptance and a frequency
response of 20 Hz to 20,000 Hz. The microphone shall operate from an
external 11V to 52V DC phantom power source. It shall be capable of
handling sound input levels up to 148 dB (158 dB with 10 dB pad) with a
dynamic range of 137 dB. Nominal open-circuit output voltage shall be 7.0
mV at 1V, 1 Pascal. Output shall be low impedance balanced (100 ohms).
The output of the microphone shall be a 3-pin XLRM-type connector.
The microphone shall be equipped with a switchable 10 dB pad and a
switch that permits choice of at response or 80 Hz low-frequency roll-off.
The microphone shall be 115.5 mm (4.55") long and have a maximum
diameter of 48.0 mm (1.89"). Weight shall be 170 grams (6.0 oz). The
microphone shall include an isolation clamp and a soft protective pouch.
Description
The AE3000 is a xed-charge condenser microphone with a cardioid polar
pattern. It is designed specically for use on high-SPL sources such as
guitar cabinets, toms, snare, timpani and overheads in professional livesound and studio applications.
The microphone requires 11V to 52V phantom power for operation.
The cardioid polar pattern of the microphone is more sensitive to sound
originating directly in front of the element, making it useful for controlling
feedback and reducing pickup of unwanted sounds.
The output of the microphone is a 3-pin XLRM-type connector.
The microphone is equipped with a switchable 10 dB pad and a switch
that permits choice of at response or low-frequency roll-off (via integral
80 Hz high-pass lter).
The microphone is enclosed in a rugged housing. The included AT8471
isolation clamp permits mounting on any microphone stand with 5/8"-27
threads. A soft protective pouch is also included.
Operation and Maintenance
The AE3000 requires 11V to 52V phantom power for operation.
Output is low impedance (Lo-Z) balanced. The signal appears across Pins
2 and 3; Pin 1 is ground (shield). Output phase is “Pin 2 hot”— positive
acoustic pressure produces positive voltage at Pin 2.
To avoid phase cancellation and poor sound, all mic cables must be wired
consistently: Pin 1-to-Pin 1, etc.
The Audio-Technica AE3000 is specied.
An integral 80 Hz high-pass lter provides easy switching from a at
Specications
Element
Polar pattern
Frequency response
Low frequency roll-off
Open circuit sensitivity
Impedance
Maximum input sound level
Noise
Dynamic range (typical)
Signal-to-noise ratio1
Phantom power requirements
Switches
Weight
Dimensions
Output connector
Audio-Technica case style
Accessories furnished
In the inter est of standards devel opment, A.T.U.S.
offers full details on its test me thods to other industr y
1 Pascal = 1 0 dynes/cm
1
Typical, A-weighted, using Audio Precision System One.
Specication s are subject to chang e without notice.
professional s on request.
2
= 10 microb ars = 94 dB SPL
AE3000
Fixed-charge back plate, permanently
polarized condenser
Cardioid
20-20,000 Hz
80 Hz, 12 dB/octave
–43 dB (7.0 mV) re 1V at 1 Pa
100 ohms
148 dB SPL, 1 kHz at 1% T.H.D.;
158 dB SPL, with 10 dB pad (nominal)
1
11 dB SPL
137 dB, 1 kHz at Max SPL
83 dB, 1 kHz at 1 Pa
11-52V DC, 3 mA typical
Flat, roll-off; 10 dB pad (nominal)
170 g (6.0 oz)
115.5 mm (4.55") long,
48.0 mm (1.89") maximum diameter
Integral 3-pin XLRM-type
R6
AT8471 isolation clamp for 5/8"-27
threaded stands; 5/8"-27 to 3/8"-16
threaded adapter; soft protective pouch
373
frequency response: 20–20,000 Hz
10 dB
100
12" or more on axis
Roll-off
330˚
200
Frequency in Hertz
0˚
180˚
500
30˚
150˚
5k
2k
1k
60˚
120˚
10k
90˚
LEGEND
200 Hz
1 kHz
5 kHz
8 kHz
50
LEGEND
polar pattern
300˚
270˚
240˚
210˚
SCALE IS 5 DECIBELS PER DIVISION
Audio-Technica U.S., Inc., 1221 Commerce Drive, Stow, Ohio 44224
Audio-Technica Limited, Old Lane, Leeds LS11 8AG England
©2010 Audio-Technica U.S., Inc. audio-technica.com 0001-0169-01
Response in dB
20k
Loading...