Audio-Technica 200-TT100-232C Users Manual

AT-LP120-USB Direct-Drive Professional USB and Analog Turntable System

Installation and Operation Pages 2-10

AT-LP120-USB

Système de tourne-disque USB professionnel à
entraînement direct

Installation et utilisation Pages 11-20

AT-LP120-USB

Sistema tocadiscos USB profesional con
accionamiento directo

Instalación y funcionamiento Páginas 21-30

Direct-Drive Professional USB and Analog Turntable System

Safety instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with a dry cloth.

7. Do not block any of the ventilation openings. Install in accordance
with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding
plug. A polarized plug has two blades with one wider than the other.
A grounding plug has two blades and a third grounding prong. The
wide blade or the third prong is provided for your safety. If the
provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly
at plugs, convenience receptacles, and the point where they exit
from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with a cart, stand, tripod, bracket or table specified by
the manufacturer, or sold with the apparatus. When a cart is used,
use caution when moving the cart/apparatus combination to avoid
injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for
long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way, such
as power-supply cord or plug is damaged, liquid has been spilled or
objects have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has
been dropped.

15. Where a mains plug is used as the disconnect device, the
disconnect device shall remain readily operable.

16. Please keep the unit in a good ventilation environment.

17. Apparatus shall not be exposed to dripping or splashing and
no objects filled with liquids, such as vases, shall be placed
on apparatus.

Warning: To reduce the risk of fire or electric shock, do not
expose this apparatus to rain or moisture. The apparatus shall not
be exposed to dripping or splashing and that no objects filled with
liquids, such as vases, shall be placed on the apparatus.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

Caution: To reduce the risk of fire or electric shock, do not expose

this apparatus to rain or moisture. The apparatus shall not be
exposed to dripping or splashing, and no objects filled with liquids,
such as vases, shall be placed on the apparatus.

The lightning flash with arrowhead symbol within the
equilateral triangle is intended to alert the use to the
presence of uninsulated “dangerous voltage” within
the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock.

Introduction

Thank you for purchasing the AT-LP120-USB Direct-Drive Professional
USB and Analog Turntable System. Audio-Technica brings its legendary
quality and audio fidelity to the digital realm with this LP-to-digital
recording system. In the box, you’ll find everything you need to transfer
your classic LP collection to digital files: Audio-Technica’s AT-LP120­USB stereo turntable, complete with USB output that allows direct
connection to your computer; Audacity recording software for MAC
or PC; an integral dual-magnet Audio-Technica phono cartridge; a USB
cable and adapter cables. The turntable also offers a built-in switchable
phono/line preamp that allows connection to a stereo system equipped
with either a phono or line-level input.

The AT-LP120-USB Direct-Drive Professional USB and Analog Turntable
System features the following:

• USB output—no special drivers required for direct connection to
your computer

• Direct drive high-torque motor

• Selectable 33/45/78 RPM speeds

• Selectable internal stereo phono pre-amplifier

• S-shaped tone arm assembly with:

•

Adjustable counterweight

•

Anti-skate adjustment

•

Tone arm height adjustment and lock

•

Tone arm lift with hydraulic action and lift lever

•

Tone arm rest with locking mechanism

• Selectable high-accuracy quartz-controlled pitch lock

• Selectable +/–10% or +/– 20% pitch adjustment ranges

• Stroboscopic platter speed indicator

• Forward and reverse play

• Cast aluminum record platter with slip mat

• Start/stop button

• Pop-up stylus target light

• 45-RPM adapter with storage receptacle

• Receptacle for extra headshell

• Adjustable feet for leveling

• Removable hinged dust cover

To assure maximum satisfaction from this product, please read the
information and follow the instructions presented in this manual. Please
keep the manual in an accessible location for future reference. We
suggest that you save all the packaging materials for possible future
storage, moving, or shipping.

Caution: To avoid stylus damage, make certain the included stylus
guard is in place whenever the turntable is being installed, moved,
or cleaned.

The exclamation point within the equilateral triangle is
intended to alert the user to the presence of important
operation and maintenance (servicing) instructions in
the literature accompanying this appliance.

Caution: To prevent electric shock, do not use this polarized plug
with an extension cord, receptacle or other outlet unless the blades
can be fully inserted to prevent blade exposure.

2

Figure 1

English

Main Features

1. POWER DIAL
Controls power to the unit.

2. START/STOP BUTTON
Engages and disengages the motor/platter.

3. PLATTER SPEED BUTTONS
Select 33 or 45 RPM platter speed. (Note: 78 RPM is selected by

pressing the 33 and 45 buttons simultaneously.)

4. PLATTER
Cast aluminum platter mounts directly to center

spindle/motor shaft.

5. STROBE DOTS (On platter edge)
Operate in conjunction with stroboscopic light located under

power dial (1) to provide visual indication of accurate platter speeds.

6. CENTER SPINDLE
Precision-machined platter mount on motor shaft.

7. 45-RPM ADAPTER (Shown in receptacle)
Adapts 7" records with large center holes to fit center spindle.

8. DUST COVER HINGE HOLDERS
Attachment points for removable hinged dust cover.

9. HEADSHELL RECEPTACLE
Storage receptacle for extra headshell (not included).

10. TONE ARM ASSEMBLY
Refer to Figure 2 on page 4 for details.

11. DIRECTION BUTTON
Controls platter’s rotational direction:
F – Forward (clockwise)
R – Reverse (counter-clockwise)

12. PITCH ADJUST SLIDE CONTROL
Use in conjunction with pitch button (15) to vary the platter’s

rotational speed. In the center detent position quartz lock is active.

13. PITCH SELECTION INDICATOR
Shows Green for standard or locked RPM setting, or Red for a

pitch-adjusted setting.

14. QUARTZ SPEED LOCK
Toggles between internal quartz-locked reference and variable

pitch controlled by pitch adjust slide control (12).

15. PITCH BUTTON
Selects the range of pitch variation permitted by the pitch adjust

slide control (12). (See page 7 for information on locking or
adjusting platter speed.)

16. POPUP STYLUS TARGET LIGHT
Provides illumination directed at the stylus position for easier

cueing in poor light.

17. VOLTAGE SELECTOR SWITCH
(Access through holes in platter)

Selects operating voltage (115V or 230V AC, 60/50 Hz).

3

Tone Arm Assembly Diagram

Figure 2

18. HEADSHELL
Standard, interchangeable stereo cartridge headshell.

19. HEADSHELL LOCKING RING
Rotate counter-clockwise (to the left) to draw the inserted

headshell firmly into its seated, locked position. Rotate the ring
a full turn to the right to permit removal of the headshell.

20. TONE ARM
S-shaped tone arm geometry reduces tracking error.

21. TONE ARM ASSEMBLY HEIGHT ADJUST
Raises and lowers the entire tone arm assembly to allow the tone

arm to remain parallel to the record surface. (The proper setting
is “0” for the included cartridge.)

22. TONE ARM LIFT
Elevates tone arm above record surface.

23. TONE ARM REST WITH LOCKING CLAMP
Locking clamp secures tone arm during transport.

24. TONE ARM LIFT ADJUST SCREW
Used to set the amount of tone arm lift.

25. TONE ARM LIFT CONTROL LEVER (“Cueing Lever”)
Controls action of tone arm lift. (Note: Lift mechanism is

hydraulically damped to slow tone arm descent.)

26. ANTI-SKATE CONTROL
Applies a small outward force to the tone arm, counteracting the

tendency of the tone arm to move inward toward the center of
the record.

27. COUNTERWEIGHT
Balances the tone arm and provides adjustment for proper

downward tracking force on the stylus.

28. TONE ARM ASSEMBLY HEIGHT LOCK
(Hidden under counterweight in drawing)

Locks the tone arm height setting. (Always fully unlock
before attempting to make a height adjustment.)

Rear View Diagram

Figure 3

29. PRE-AMP SELECTOR SWITCH
Allows the internal stereo phono pre-amp to be bypassed
when the turntable is used with equipment having
magnetic phono inputs.

30. USB OUTPUT
Use this output to connect your turntable to the USB input of

your computer. Please see included software guide for
instructions.

29

30

4

English

Initial Setup

Unpacking

Carefully unpack the turntable and verify that the following parts are
included and intact:

• Slip mat (above the dust cover)

• Dust cover (above the turntable)

• Platter (under the turntable)

• Dust cover hinges (accessory section of the
foam packaging)

• 45 RPM adapter (accessory section)

• Counterweight (accessory section)

• Headshell with pre-mounted cartridge
(accessory section)

• Power cord (accessory section)

• USB cable

• Dual RCA (female) to 3.5 mm (1/8") mini-plug (male)
stereo adapter cable

• Dual RCA (female) to 3.5 mm (1/8") mini-plug (female)
stereo adapter cable

• Audacity software (CD)

WE RECOMMEND THAT YOU SAVE ALL PACKAGING
MATERIALS FOR POSSIBLE FUTURE STORAGE, MOVING OR
SHIPPING.

Assembling the Turntable

The AT-LP120-USB requires some assembly before first use.
IMPORTANT: Do not connect the AC power cord until assembly is
complete.

Setting the Voltage Selector Switch

This turntable has the capability to be used with either 115V or 230V
AC power, 60/50 Hz. The voltage selector switch is located on the
top of the housing deck, under the platter. Set the switch according
to the voltage in your area. [See Figure 4.] (Note: The turntable comes
shipped with the voltage selector switch set for 115V AC.)

When using the turntable with a computer sound card, set the switch
to LINE OUT and connect the turntable to the audio line input on the
computer sound card. Note: An audio adapter (not included) may be
required to interface the two RCA jacks of the turntable output cable to
the computer sound card input.

Assembling the Tone Arm

(Note: The headshell and cartridge are supplied pre-assembled with the
AT-LP120-USB.)

1. Remove the vinyl tie used to secure the tone arm during
shipment. Temporarily secure the tone arm in the tone arm
rest with the locking clamp. [Figure 2, page 4, #23.]

2. Attach the headshell assembly by inserting it into the
socket at the front of the tone arm [See Figure 5.] (It’s
good practice always to hold a headshell assembly by the
left and right edges of the headshell to reduce the
possibility of damaging the stylus or disrupting the
cartridge wiring.)

3. While holding the headshell in position, rotate the
headshell locking ring counter-clockwise (to the left).
As the ring turns, it pulls the headshell into its seated
position. (Rotate the ring a full turn to the right to permit
removal of the headshell.)

4. With its black dial toward the front, use a screwing motion
to attach the counterweight to the arm extending back
from the tone arm pivot [Figure 2, page 4, #27]; the
counterweight will engage the spiral groove in the rear arm
section and move forward.

Figure 5 – Headshell

Figure 4 – Voltage Switch

Voltage
switch

Setting the Pre-amp Selector Switch

For increased flexibility of use, this turntable has an internal stereo
phono pre-amplifier. The pre-amp selector switch located in the rear­panel of the turntable [See Figure 3, page 4, #29], selects the internal
stereo pre-amplifier (LINE OUT), or bypasses the pre-amp (PHONO
OUT) for use with systems having specialized magnetic phono input
jacks. The audio output cable’s Red RCA-type plug is the Right channel;
the White plug is the Left channel.

If the system you are using has a PHONO input, set the pre-amp
selector switch to the PHONO OUT position and connect the
turntable’s output cables to the PHONO inputs on your system,
observing Red for Right channel and White for Left channel.

If your system does not have a PHONO (magnetic phono) input, set the
pre-amp selector switch to LINE OUT and connect the turntable’s output
cables to the Auxiliary (AUX) or other high-level inputs on your system,
observing Red for Right channel and White for Left channel.

Assembling the Turntable Platter and Slip Mat

1. Carefully place the turntable platter on the center spindle,
making certain the platter is fully seated on the spindle.
[See Figure 6.]

2. Place the soft black slip mat on top of the platter.

Figure 6 – Platter and Slip Mat

5

Initial Setup (continued)

Assembling the Dust Cover

1. Insert the T-shaped ends of the dust cover hinges into the two
hinge receptacles located at the back of the turntable housing.
When properly installed, the flat part of the cover hinges should be
facing away from the turntable housing at about a 45° angle.

2. Holding the dust cover over the turntable, carefully guide the cover
hinges into the two slots molded into the rear of the dust cover.
The springs in the hinges allow the cover to be held open at about
a 45° angle if desired. (Note: There is only one “open” position;
the hinges do NOT permit the cover to stand “straight up.”)

3. To remove the dust cover from the turntable, gently disengage the
hinges from the slots in the cover. This is usually easier when the
cover is in the “closed” position. Slowly and carefully lift straight
up until the cover is clear of the unit. The hinges may then be
removed from the turntable base, if desired.

Setting Tone Arm Balance and Tracking Force

To allow the cartridge to properly track in a record, the tone arm
balance and tracking force must be carefully set to the cartridge
manufacturer’s specifications. Failure to properly set up the tone arm
assembly can cause damage to the cartridge stylus and/or records.

(Note: Once the stylus protective cover has been removed and the tone
arm locking clamp has been released, take extreme care not to damage
the stylus. Do not allow it to drag or scrape across the slip mat.)

Tone Arm Setup:

1. Set the anti-skate adjustment to “0”. [Figure 2, page 4, #26.]

2. Remove the clear protective stylus cover, carefully sliding it
straight forward, off the front of the cartridge.

3. While gently holding the headshell to stabilize the tone arm,
release the tone arm locking clamp. At this point, the tone arm is
unbalanced and free to swing.

4. While gently holding the headshell, carefully rotate the
counterweight until the tone arm is horizontally balanced and
hovers freely just above the platter without touching the platter
surface.

5. Lock the tone arm back into the tone arm rest.

6. While holding the counterweight steady, and without any rotation,
carefully rotate only the black stylus force gauge ring (which turns
independently of the counterweight) until the “0” on the gauge ring
lines up with the centerline marked along the top of the rear arm.

7. Refer to the cartridge manufacturer’s specifications for
recommended tracking force. Rotate the entire counter-weight
counterclockwise without touching the black gauge ring, moving
the counterweight forward, until the desired value on gauge ring
lines up with the centerline marked on the rear arm. Refer to the
specifications section for tracking force value for the cartridge that
shipped with the turntable.

Setting Anti-skate

A small outward “anti-skating” force can be applied to the tone arm
to compensate for the “skating” force that pulls the arm toward the
center of the record. For best performance during normal turntable
use, set the anti-skate control knob [Figure 2, page 4, #26] to the same
setting as the tracking force dial. Refer to the specifications section for
tracking force value of the cartridge that shipped with the turntable.

Setting Tone Arm Assembly Height

The tone arm assembly height adjustment allows for the tone arm
to be positioned parallel to the record surface, when using extra-tall
cartridge bodies, thick slip mats or thick records (i.e. old 78’s). To raise
or lower the tone arm assembly: First, loosen the height lock [Figure 2,
page 4, #28]; then rotate the height adjust dial [Figure 2, page 4, #21]
located at the base of the tone arm assembly. The scale is calibrated in
millimeters (mm). When finished, tighten the height lock to secure the
adjustment.

Connections

Audio
Connect the audio output cable to the appropriate input jacks on your

mixer, amplifier, soundcard or other device based on the setting of the
pre-amp selector switch. Firmly connect the Red RCA-type plug to the
right channel input and the White RCA-type plug to the left channel
input. (Note: Adapter plugs might be required to connect the turntable
to computer sound cards and other devices.)

Connecting to Computers with USB Input
The USB cable (included) connects your AT-LP120-USB turntable to

your computer without need for special drivers. Refer to included
software guide (also available online at www.audio-technica.com)
before connecting the turntable to your computer.

Connecting to Computers or Audio Devices with 3.5 mm Input
The AT-LP120-USB connects without adapters to devices equipped with
RCA connectors. For maximum flexibility, we have included two adapter
cables to fit other popular audio inputs.

The first of these adapter cables – dual RCA to stereo 3.5 mm mini-plug
(male) – is designed to fit most popular computer* audio inputs. It may
also be used to connect the turntable’s RCA output to other equipment,
including:

• a stereo/boombox* equipped with a 3.5 mm minijack

• input powered speakers* equipped with a 3.5 mm minijack

• input a mixer* or PA system* equipped with a 3.5 mm minijack

The second included adapter cable – dual RCA to stereo 3.5 mm mini­plug (female) – permits connection of the turntable output to amplified
speakers* or similar devices. The 3.5 mm stereo minijack on the cable
adapter accepts stereo mini-plugs.

To use either adapter cable, connect the turntable’s red and white RCA­type plugs to the cable adapter’s RCA-type jacks.

* When using either cable adapter, always set the AT-LP120-USB
turntable’s Pre-amp Selector Switch to the “LINE” position.
(Switch is located on the back of the turntable.)

NOTE: If connection is desired to a mono amplifier/speaker, make
certain to use a stereo-to-mono adapter, available from your dealer or
an electronic parts store. Inserting a mono plug in the stereo jack will
disable one of the stereo channels. Other adapter cable configurations
will be available from dealers and parts stores for connecting to devices
needing different terminations.

Finally, after all other connections are made, attach the included AC
power cord to the turntable; note that the small connector only goes
in one way. Then connect the power cord’s plug to a convenient AC
outlet.

In case of substantial use of back-cueing, scratching or reverse-direction
operation, you may prefer to use less, or no, anti-skate compensation.

6

English

Operation

For best results, do not install or operate this unit near conditions of
heat, moisture, dust, or heavy vibrations. (Note: Bright fluorescent lights
may affect the visibility of the speed-indicating strobe dots. If this is a
problem, simply cover the area with your hand, an album cover, etc.)

Preparing to Play

1. Remove the stylus guard from the stylus assembly and unlock the
tone arm rest if it is locked.

2. Turn the power dial to the ON position. The speed selector and
strobe illuminator will light up.

3. If desired, push the stylus target light button to raise and turn on
the light for illumination of the stylus tip position on the record.

4. Place a record on the slip mat, lining up its center hole with the
center spindle. For 45RPM records, place the 45 RPM adapter on
the center spindle before placing the record on the platter.

5. Set the platter rotation speed (33/45/78) to match that of the
record. (Note: To set the platter speed for 78 RPM, push both the
33 and 45 RPM buttons simultaneously.)

Playing the Record

1. Press the start/stop button; the platter begins to rotate.

2. Raise the tone arm by lifting the tone arm lift control lever to the
UP position.

3. Position the tone arm over the desired location (groove) on
the record.

4. Lower the tone arm by moving the tone arm lift control lever to
the DOWN position. The tone arm descends slowly onto the
record and play begins.

– or –

Use the finger-lift on the headshell assembly to position the tone
arm over the desired location on the record. Carefully lower the
tone arm to the record surface.

Checking and Adjusting Pitch

1. If desired, select a +/– 10% or +/– 20% pitch adjustment range by
pressing the pitch button. Then move the pitch adjust slide control
up or down to make pitch adjustments. (Note: The pitch adjust
slide control has center detent position for 0% pitch variation.)

2. As illuminated by the red light coming from beneath the power
dial, observe the strobe dots on the edge of the platter. If the
appropriate row of strobe dots appears to be stationary, the platter
is moving at the precise rated speed. If the dots appear to be
moving to the right, the platter is moving below rated speed; if
they appear to be moving to the left, the platter is moving above
rated speed.

50Hz

3. If the quartz speed lock button is pressed, the internal quartz lock
will hold the platter at precise rated speed regardless of the
position of the pitch adjust slide control. (Note: The LED indicator
to the left of the pitch adjust slide control’s center position will
illuminate GREEN when the quartz lock is active and RED when
variable pitch is active.)

4. If desired, press the direction button to reverse the rotation of the
platter. The appropriate direction LED will illuminate.

Suspending or Ending Play

1. To suspend play, lift the tone arm with the cueing lever.

2. When play is finished, raise the cueing lever, move the tone arm
to the rest position and secure the tone arm with the tone arm
locking clamp.

3. If using the stylus target light, turn it off by pushing the
light down.

4. Press the start/stop button to apply the brake and stop the
platter rotation.

5. Turn the power dial to the OFF position.

33

45

60Hz

33

45

7

Replacing the Stylus

Replacing the Stylus

The AT-LP120-USB comes supplied with a high-quality Audio-Technica
AT95E cartridge. The stylus should be replaced with a genuine
Audio-Technica ATN95E stylus.

1. Release the headshell assembly from the tone arm by turning the
locking ring clockwise.

2. Carefully remove the headshell assembly and turn it over so the
stylus is visible.

3. Remove the stylus assembly by pulling it away from the cartridge
body at a slight angle. [See Figure 7.]

4. Remove the replacement stylus from its package and carefully
align it with the cartridge body.

Replacing the Cartridge

Mechanical Assembly

1. To replace the cartridge, first release the headshell assembly from
the tone arm by turning the locking ring clockwise. Carefully
remove the headshell assembly and turn it over so that the stylus
is visible. Remove the stylus assembly by pulling it away from the
cartridge body at a slight angle. [See Figure 7.] Place the stylus
assembly out of harm’s way.

2. Remove the cartridge body by loosening the two small screws
securing the cartridge to the headshell. Set the hardware aside to
be reused with the new cartridge.

3. Unpack the new cartridge and carefully remove its stylus
assembly. Place the stylus assembly out of harm’s way. Mount
the new cartridge to the headshell assembly. Use the mounting
hardware supplied with the new cartridge or the existing hardware
removed at step 2. Tighten the mounting screws until just snug.
Replace the stylus assembly briefly to check for mechanical
interference with the mounting hardware. The stylus assembly
should click into place. Make certain the new cartridge is properly
positioned in the headcase assembly per the manufacturer’s
instructions. Again remove the stylus assembly for safekeeping.

5. Gently push the stylus onto the cartridge body, being careful not to
damage the stylus. The stylus assembly should click into place.

6. Replace the headshell assembly on the tone arm and secure with
the locking ring.

Figure 7 – Removing the Stylus

Electrical Connections

1. Four terminals at the rear of the cartridge are color coded to match
standard wiring in stereo tone arms. [See Figure 8.] Connect the
cartridge with the slip-on lugs provided on the headshell wiring.
NEVER SOLDER TO CARTRIDGE TERMINALS! Heat applied to
the terminals will damage the internal cartridge wiring.

2. For monaural operation, the left and right signal leads should be
connected to the monaural output terminal and the left and right
ground leads should be connected to the ground terminal.

3. Finally, gently push the stylus onto the cartridge body being
careful not to damage the stylus. The stylus assembly should click
into place. Replace the headshell assembly onto the tone arm
taking care not to damage the stylus assembly.

(Note: After replacing the cartridge, reset the tone arm balance, stylus
force and anti-skate based on the new cartridge’s specifications.)

Figure 8 – Electrical Connections

Right Output

(Red)

Left Output

(White)

Right Ground

(Green)

Left Ground

(Blue)

8

English

Troubleshooting

Turntable operates but emits no sound or not enough sound.

1. The stylus guard is still in place. Remove the stylus guard.

2. The tone arm is in the lift position. Lower the tone arm.

3. Mixer/amplifier (system) controls are set incorrectly: wrong input
selected, tape monitor on, speakers switched off, etc. Verify
proper control settings.

4. Stylus is broken or missing. Check the stylus assembly and
replace if necessary.

5. The stylus assembly may not be fully seated in the cartridge body.
Check the cartridge and adjust if necessary.

6. The pre-amp selector switch is set in the wrong position. Verify
that it is set for proper output to match mixer/amplifier.

- No sound/very weak sound: Phono Out setting into an
Aux/Line input.

- Very loud/distorted sound: Line Out setting into a
Phono input.

Turntable operates but stylus “skips” across record.

1. The stylus guard is still in place. Remove the stylus guard.

2. The tracking force is set too light. Set tracking force per cartridge
manufacturer’s recommendation.

3. The tracking force is set too heavy (stylus assembly is bottoming
out on record). Set tracking force per cartridge manufacturer’s
recommendation.

Record sounds too fast or too slow.

1. Turntable is set for wrong speed. Make proper speed selection for
record type being played with platter speed buttons.

2. Variable pitch is engaged. Depress quartz button or return pitch
adjust slider to center detent position to engage quartz lock.

Moving pitch adjust slider produces no effect.

If the LED next to the pitch adjust slider center detent position remains
green when the slider is moved, quartz lock is engaged. Depress the
quartz button to disengage the quartz lock and activate variable pitch.
The LED should turn RED.

Strobe dots are difficult to see and/or stylus illuminator is very dim.

1. Excessively bright or fluorescent light interferes with strobe
indicator. Hold hand, record jacket, etc. over strobe indicator to
shield it from bright light.

2. Voltage selector switch is set for 230V when AC mains are 115V.
Disconnect AC power cord and reset the voltage selector switch
located under the platter. (Note: Even with the voltage selector
set for 230V when AC mains are 115V, the quartz lock will bring
the platter up to proper speed.)

4. The anti-skate control is set improperly. Verify anti-skate is set for
same value as cartridge tracking force.

5 Turntable is picking up excessive vibrations from floor, walls, or
nearby speakers. Reduce vibrations or place turntable on sturdy/
solid surface.

Tips For Better Performance

• When opening or closing the turntable cover, handle it gently,
moving it either at the center or equally from both sides.

• Do not touch the stylus tip with your fingers; avoid bumping
the stylus on the turntable mat or a record’s edge.

• Clean the stylus tip frequently, using a soft brush and a back-

to-front motion.

• If you use a stylus cleaning fluid, use it sparingly.

• Wipe the dust cover and turntable housing gently with a soft
cloth. Use only a small amount of mild detergent solution to
clean the turntable and dust cover.

• Never apply harsh chemicals or solvents to any part of the
turntable system.

• Prior to moving the turntable, always unplug it from the AC
outlet and lock the tone arm on the tone arm rest.

9

Specications

†

Turntable Specifications

Type 3-Speed, fully manual operation
Motor DC motor
Drive method Direct drive
Speeds 33-1/3 RPM, 45 RPM, 78 RPM
Pitch variation +/- 10% or +/- 20%
Turntable platter Die-cast aluminum
Starting torque >1.6 kgf.cm
Braking system Electronic brake
Wow and flutter < 0.2% WRMS (33 RPM)
Signal-to-noise ratio > 50 dB
Output level

Pre-amp “PHONO” 2.5 mV nominal at 1 kHz, 5 cm/sec
Pre-amp “LINE” 150 mV nominal at 1 kHz, 5 cm/sec

Phono pre-amp gain 36 dB nominal, RIAA equalized
USB function

A/D, D/A 16 bit 44.1 kHz or 48 kHz USB selectable
Computer interface USB 1.1 Compliant Windows XP, Vista or
MAC OSX

Power supply 115/230V AC, 60/50 Hz
requirements

Power consumption 11W
Dimensions 450.0 mm (17.72") W x 352.0 mm

(13.86") D x 157.0 mm (6.1") H
Weight 10.7 kg (23.5 lbs.)
Accessories included Headshell/cartridge (AT95E); AC line cord;

dual RCA (female) to 3.5 mm (
plug (male) stereo adapter cable; dual
RCA (female) to 3.5 mm (
(female) stereo adapter cable; 45 RPM
adapter; USB cable; recording software

1

/8") mini-

1

/8") mini-plug

Cartridge Specifications (AT95E)

Frequency response 20 – 20,000 Hz
Channel separation >20 dB at 1 kHz
Vertical tracking force 1.5 – 2.5 grams
Stylus construction Bonded round shank
Output 3.5 mV at 1 kHz, 5 cm/sec
Channel balance 2.0 dB
Stylus shape 0.4 x 0.7 mil elliptical
Cantilever Aluminum
Mount Half-inch
Replacement stylus ATN95E

†

Specications are subject to change without notice.

10