AudioSource AS6c User Manual

AS6c

6.5” 2-Way In-Ceiling Speakers

Congratulations on your purchase of the Audiource
AS6c In-Ceiling Speaker System. This product is
designed to reproduce the audio portion of your
home entertainment environment with accuracy and
detail that will satisfy the most discriminating
listener.

Please read this Installation Manual to ensure the
proper installation and performance of your AS6c
speakers.

Preparing for your Installation

Gather the necessary tools for your installation.

You will need the following tools:

1) A Keyhole or Drywall Saw

2) A Phillips Screwdriver

3) Masking Tape

4) A Pencil

5) A Bubble or Laser Level

6) A Tape Measure

7) A Stud Finder (recommended)

8) Your AS6c speakers

Placement

Plan your speaker placement carefully. Make certain
that electrical, plumbing and any other services will not
interfere within the ceiling where you plan to place your
speakers. The AS6c speakers can be mounted in the
walls or in the ceiling, but are typically used in ceilings.
The speakers should be located so that they provide
even coverage at your listening position. The distance
between the speakers should not be greater than the
distance from the speakers to the listening position.
(See Fig. 1) If the room’s dimensions or furniture
placement prevent adhering to this requirement, the
tweeters in the AS6c speakers can be swiveled to aim
them at the desired listening position.

AS6c

Existing Construction

In most modern buildings the ceiling joists are positioned
on 16” centers, providing a space between the joists of
approximately 14 3/8”. The AS6c requires a mounting
hole 7 3/4“ in diameter. Also, you should allow an
extra 3/4” clearance in all directions behind the ceiling
surface to allow room for the doglegs that retain the
frame to the ceiling surface to swing into position.

Use a stud finder to locate the joists behind the ceiling
surface. Also, you should now check for obstructions like
cross bracing in front of and behind the desired speaker
location.

11’

11.5’

New Construction

If you are installing your speakers in new construction
before the finished walls go up, AudioSource offers a
Pre-Construction Bracket, Part NCBC6 that provides a
stable frame that can be fastened to the wall studs or
ceiling joists on 16” or 24” centers. This allows the
sheetrock or other surface covering to be installed and
clearly leave the opening for the AS6c speakers.

20’

16’

Figure 1

After selection of the mounting location, mark the hole to
be cut out. A template is provided in the speaker box.
Locate and align the template, then mark with pencil on
the ceiling surface. If you are unsure whether there are
obstructions behind the ceiling surface where the
speakers are to be mounted cut a small hole in the
center of your marked mounting location. Holding your
drywall saw at a 45 degree angle (See Fig. 2) cut a
square hole that you can use to locate any obstructions,
should they exist.

ROOM

Figure 2

The 45 degree wedge shape of the removed surfacing
material will make replacement, if necessary, a much
easier task and yield a better finish when patching the
work.

Once it has been determined that there are no obstruc­tions cut the hole to mount the speaker using the drywall
saw at a 90 degree angle to the ceiling surface. Cover
the raw edges of the wallboard with masking tape
(See Fig. 3). This will prevent the back pressure of the
speaker from blowing loose gypsum dust out and on to
the painted ceiling surface after installation. Do not allow
the tape to extend more than 1/4” beyond the edge of
the hole into the room. The frame of the AS6c will cover
and hide the tape.

Masking T.ape

ROOM

Figure 3

the uninsulated ceiling.

It is now time to connect the speaker wire to the AS6c.
Your speaker wire is usually coded to identify each
conductor as either positive or negative. This can be by
color coding, or one conductor may have a printed
marking or at least a rib along one edge that you will not
find on the other. Identify which type of polarity coding
that your wire is using. You must carefully observe that
the positive terminal of the speaker output on your
amplifier is connected to the positive terminal of the
AS6c speaker. Likewise, the negative terminal of the
amplifier’s speaker output should be connected to the
negative terminal of the AS6c speaker.

(-) Amp

AS6c

6.5” Two Way In-Ceilling
100W / 8 ohm

(+) Amp

Next make sure that the doglegs are positioned inside
the frame of the speaker.

Correct

Next you will want to run your speaker wire to your
speaker locations. A UL rated CL3 speaker wire is
recommended when running wire inside your walls.
In many areas it may be required by code. When running
your speaker wire you should avoid having the speaker
wire run parallel to the 110V power lines to avoid picking
up hum and interference from the power service. If the
speaker wire needs to cross a 110V power line at a right
angle this is acceptable and should not create a
problem.

If you are uncomfortable with running the speaker wire
yourself in existing construction, it is recommended that
you retain a qualified custom home installation specialist
or electrician.

Installing the Speakers

Installation Tip! To further enhance the performance of
your AS6c speakers, the ceiling joist cavity where you
plan to place your speakers can be stuffed with a
generous quantity of fiberglass insulation. If uninsulated,
stuff the area in front of and behind the speaker opening
with 6” thick insulation to a depth of approximately 2 feet
beginning 1 foot in front of and 1 foot behind the speaker
opening. If the insulation is foil or paper backed, face the
backing away from the AS6c speaker. The addition of
this insulation will help to prevent the unwanted transfer
of sound into the otherwise large and resonant cavity of

AS6c

6.5” Two Way In-Ceilling
100W / 8 ohm

Incorrect

With the grill removed, place the speaker in the ceiling
opening. Make sure that the speaker wire is not hanging
against the speaker where it can vibrate and rattle as the
speaker reproduces your audio program.

Next, one at a time, turn
each of the four screws

1

that operate the doglegs
counter clockwise a few
turns until you feel the
dogleg is loose from its
resting position. Now turn
the screw clockwise until
you feel the dogleg
contact the wall surface.

3

2

2

4