AudioSource AMP 110, AMP 310, AMP 210, AMP 100, AMP 102 User Manual

AMPLIFIER APPLICATION GUIDE

AMP 100
AMP 102
AMP 110
AMP 210
AMP 310

Amplifier Guide

AudioSource AMP series amplifiers are designed for home and commercial
audio distribution systems where high quality sound, flexibility, and reliability are
essential. The AMP series offers exceptional value and many features that will
make their installation and use easy and convenient.

The AudioSource AMP series consists of 5 amplifier models ranging from 50
watts per channel to 150 watts. The amplifiers share some common features with
intelligent industrial design, superior engineering and value as key components
to the AMP series success story.

AMP Series Products….. Value Priced Engineering Excellence!

All models incorporate the following features:

1. Bridgeable Outputs

2. Dual Stereo Inputs

3. Priority Input Switching (Automatic)

4. Heavy Duty Aluminum Faceplates

5. Stereo Line Outputs

6. Separate Volume and Balance Controls

7. 5-Way Binding Posts

8. A and B Speaker Selector Switches

9. Auto On (By-passable)

Amplifier Technology

The AMP 110, AMP 210, and AMP 310 incorporate very precise
circuit topology to ensure the best audio reproduction. Dual Differential Error
amplifiers ensure linearity and low noise operation. Triple Darlington output
stages ensure the amplifier can drive complex speaker loads without adding
distortion. In addition, toroidal power transformers are used with large filter
capacitors to create stunning audio dynamics.

Careful Engineering

When discussing AMP series products with your contractors it’s important to note
that the entire AMP series went through rigorous testing procedures in Portland,
Oregon by AudioSource’s engineering staff. Years of audio engineering
experience have been applied to these amplifiers to ensure years of use.

AMP100 AMP102 AMP110 AMP210 AMP310

Number of
Ch

annels

Load

ance 8ohm 4ohm 8ohm 4ohm 8ohm 4ohm 8ohm 4ohm 8ohm 4ohm

Imped
Rated Output
Power
Frequency
Res

ponse
Signal to
Noise

Ratio

Input
Sensitivity
THD at Rated
Power

Dimensions

Weight 12 lbs 14.7 lbs 23.1 lbs 24 lbs 33.1 lbs

2 2 2 2 2

50 60 50 75 75 110 90 125 150 225

20-20kHz 20-50kHz 20-50kHz 20-50kHz 20-50kHz

100dB 100dB 100dB 100dB 100dB

350mV-

1.5Vrms

<.2% <.1% <.1% <.1% <.1%

2.9"H x 16.5"W x

9.25"D

2.8Vrms

3.8"H x 16.5"W x

8.25"D

350mV-

2.8Vrms

3.8"H x 16.5"W
x 13.75"D

350mV-

2.8Vrms

3.8"H x 16.5"W x

13.75"D

350mV-

2.8Vrms

5.5"H x 16.5"W x

13.75"D

AMP 100

Applications:

Ideal for use as a remote amplifier

Use with Whole House Distributed Audio Systems
Second Zone Amplifier
Amplify MP3 Players
Rear Channel Amplifier for Dolby 6.1 and 7.1 Systems
Perfect for Computers and Video Games

Key Features:

Affordable!

2 Independent channels rated at 50 watts into 8 ohms
60 watts per channel into 4 ohms
Independent level and balance control
Dual Auto-Switching Inputs
Auto Signal Sensing Power On
A/B Speaker selector
Bridgeable

Specifications

Power: 50 watts RMS @ 8 ohms
60 watts @ 4 ohms
Less than 0.2% THD into 8 ohms
Input Sensitivity 1.5 Vrms
S/N Ratio: 100 dB A-weighted
Frequency response: 20Hz to 20kHz

AMP 102

Applications:

Ideal for use as a Remote Amplifier
Use with Whole House Distributed Audio Systems
Second Zone Amplifier
Amplify MP3 Players
Rear Channel Amplifier for Dolby 6.1 and 7.1 Systems
Perfect for Computers and Video Games
Ideal for In-Wall and In-Ceiling Speaker Systems

Key Features:

Even More Affordable Power!

2 Independent channels rated at 50 watts into 8 ohms
75 watts per channel into 4 ohms
Independent level and balance control
Dual Auto-Switching Inputs
Auto Signal Sensing Power On
A/B Speaker selector
Front Panel diagnostic LEDs
Bridgeable
12VDC “Trigger On”
Rack-mount ready

Specifications

Power: 50 watts RMS @ 8 ohms
75 watts @ 4 ohms
Less than 0.1% THD into 8 ohms
Input Sensitivity: 350mV to 2.8Vrms
S/N Ratio: 100 dB A-weighted
Frequency response: 20Hz to 50kHz