Page 1
INSTALLATION MANUAL
TECHNOLOGY
KS-2-DX4056 EYE
(Patent Pending)
K-2 or S-2 Package required for installation
SPECIFICATIONS
Power: Supplied from K-2/S-2 package.
Connectors: Screw type connectors.
Remotes: Kenwood / Sony.
Range: 25-35 feet.
Angle: + or - 35 degrees off nominal axis.
Wire: Must be wired with two 16-2 wires.
The KS-2-DX4056 Eye works in conjunction with the K-2 / S-2 package, creating a 2-way system
designed to receive infrared signals from remote controllers via remote sensors, and send them to the base
unit, which in turn sends these signals to remote repeaters. This unit also sends a return signal back to the
remote control, confirming that the signal has been received. This system is not capable of making devices
remote controllable that are not so already, but allows remote system operation from any room in a structure
where the KS-2 Eye sensors are installed. NOTE: No more than 4 sensors should be used in a system.
INSTALLATION
The K-2 / S-2 base unit must be positioned in a location to receive the 455khz data signal from the
front of the A/V Receiver. Either in front, beside, or by using reflective material to direct the signal. If the 1/8"
jumper accesory for Kenwood is not used then the TBW emitter should likewise be positioned. If using the
Stick-Emit, the emitter should be positioned directly over the component's IR sensor. You may have to move
the emitter around to find the "sweet spot". Once a good position is found, peel the backing paper off and
adhere the emitter to the unit. Make sure that the emitter is not in the line of sight or reflection of any
sensors as radiation from the repeater may be picked up by a system sensor, resulting in a feedback situation
which causes instability and unreliable operation. Undesirable reflection can occur off light colored walls,
windows, mirrors and even shiny wood finishes. Connect the emitter to central processor and to the sensor
eyes, following the wiring diagram on the back of this sheet. The system must be wired with two 16-2 wires.
For connection, prepare the wire leads for the emitter and all remote sensors by stripping about 1/4"
of insulation from each of the wire ends. Twist strands tightly together so that none stick out to cause possible
short circuits. Insert the wire ends into the outputs on the back of the base unit following the wiring diagram
on the back of this page. Tighten all screws and inspect for loose wire strands, etc.
Plug the power supply into the wall, and the wire lead into the jack labeled POWER on the back of the
base unit. The unit is now ready to operate.
Your AUDIOPLEX TECHNOLOGY KS-2 Eye is covered by a LIFETIME warranty against any defects
in workmanship and materials. Any defects will be remedied without charge for labor or parts.
Damage incurred by shipping or by accident is not considered to be a defect, and not covered by this
warranty. AUDIOPLEX TECHNOLOGY is not responsible for defective operation caused by abuse or by
modification or service by any unauthorized person or agency.
The unit must be properly installed and operated according to instructions for the warranty to apply.
Any necessary servicing must be done by AUDIOPLEX TECHNOLOGY. The unit must be shipped with the
proof of purchase and in the original carton and packing materials to avoid damage.
This warranty gives you specific legal rights. You may have other rights which vary from state to state.
2003 - 5/12/03
WARRANTY
Page 2
WIRING DIAGRAM
KS-2 RECEIVER EYE
(OPTIONAL)
40
455
GD
12V
1/8" jumper accessory for Kenwood Receivers to "IR Receiver In".
SEE KENWOOD INTRUCTIONS!!!!
2-WAY A/V RECEIVER
KS-2 RECEIVER EYE
(OPTIONAL)
40
455
GD
12V
GD
EMITTER SIGNAL +
KS-2 RECEIVER EYE
(OPTIONAL)
40
455
GD
12V
KS-2 RECEIVER EYE
( 1 INCLUDED WITH PACKAGE)
40
455
GD
12V
IMPORTANT NOTE:
Use two equal length 16/2
wires to connect the receiver
eye to the base unit as follows:
(1) one 16/2 connects the 40
12V
GD
455 KHz
kHz signal and the 12 VDC.
40 KHz
(2) second 16/2 connect the
455 kHZ signal and ground.
OPTIONAL EMITTER
12 VDC POWER SUPPLY
404 GWH P.O. BOX 440 MELVIN VILLAGE, NH 03850
800-257-2077 603-544-8601 FAX: 603-544-8901
12
GD GD
K-2/ S-2 BASE UNIT
2003 - 5/12/03
455
AUDIOPLEX TECHNOLOGY
www.audioplex.com
This connection method
ensures optimum operation.
EMITTER SIGNAL +
40
S
Loading...