Caissons de basses amplifiés 15/18 pouces bass reflex avec DSP
Enceintes amplifiées 10/12/15 pouces 2 voies bass reflex avec DSP
GUIDE DE L’UTILISATEUR
10779/10780/10781/10782/10783 - Version 1 / 01-2018
ATOM series - 2 ways 10/12/15" powered full range speaker and 15/18" powered subwoofer with DSP
1 - Safety information
Important safety information
This product contains non-isolated electrical components. Do not
undertake any maintenance operation when it is switched on as it
may result in electric shock.
This unit is intended for indoor use only. Do not use it in a wet, or
extremely cold/hot locations. Failure to follow these safety instructions could result in fire, electric shock, injury, or damage to this
product or other property.
WARNING : This unit contains no user-serviceable parts. Do not open the
housing or attempt any maintenance by yourself. In the unlikely even your unit may
require service, please contact your nearest dealer.
In order to avoid any electrical malfunction, please do not use any multi-socket, power
cord extension or connecting system without making sure they are
and present no defect.
perfectly isolated
Any maintenance procedure must be performed by a CONTEST
authorised technical service. Basic cleaning operations must thoroughly follow our safety instructions.
Symbols used
This symbol signals an important safety precaution.
The CAUTION symbol signals a risk of product deterioration.
The WARNING symbol signals a risk to the user’s physical integrity.
The product may also be damaged.
Instructions and recommendations
1 - Please read carefully :
We strongly recommend to read carefully and understand the safety instructions before
attempting to operate this unit.
2 - Please keep this manual :
We strongly recommend to keep this manual with the unit for future reference.
3 - Operate carefully this product :
We strongly recommend to take into consideration every safety instruction.
4 - Follow the instructions:
Please carefully follow each safety instruction to avoid any physical harm or property
damage.
5 - Avoid water and wet locations :
Do not use this product in rain, or near washbasins or other wet locations.
6 - Installation :
We strongly encourage you to only use a fixation system or support recommended
by the manufacturer or supplied with this product. Carefully follow the installation
instructions and use the adequate tools.
Always ensure this unit is firmly fixed to avoid vibration and slipping while operating
as it may result in physical injury.
7 - Ceiling or wall installation :
Please contact your local dealer before attempting any ceiling or wall installation.
8 - Ventilation :
The cooling vents ensure a safe use of this product, and avoid any overheating risk.
Do not obstruct or cover these vents as it may result in overheating and potential
physical injury or product damage. This product should never been operated in a
closed non-ventilated area such as a flight case or a rack, unless cooling vents are
provided for the purpose .
9 - Heat exposure :
Sustained contact or proximity with warm surfaces may cause overheating and product
damages. Please keep this product away from any heat source such as a heaters,
amplifiers, hot plates, etc...
Page 2
Sound levels
Our audio solutions deliver important sound pressure levels
(SPL) that can be harmful to human health when exposed
during long periods. Please do not stay in close proximity
of operating speakers.
Recycling your device
10 - Electric power supply :
This product can only be operated according to a very specific voltage. These
information are specified on the label located at the rear of the product.
11 - Power cords protection:
Power-supply cords should be routed so that they are not likely to be walked on or
pinched by items placed upon or against them, paying particular attention to cords at
lugs, convenience receptacles and the point where they exit from the fixture.
12 - Cleaning precautions :
Unplug the product before attempting any cleaning operation. This product should be
cleaned only with accessories recommended by the manufacturer. Use a damp cloth
to clean the surface. Do not wash this product.
13 - Long periods of non use :
Disconnect the unit’s main power during long periods of non use.
14 - Liquids or objects penetration :
Do not let any object penetrate this product as it may result in electric shock or fire.
Never spill any liquid on this product as it may infiltrate the electronic components
and result in electric shock or fire.
15 - This product should be serviced when :
Please contact the qualified service personnel if :
- The power cord or the plug has been damaged.
- Objects have fallen or liquid has been spilled into the appliance.
- The appliance has been exposed to rain or water.
- The product does not appear to operate normally.
- The product has been damaged.
16 - Inspection/maintenance :
Please do not attempt any inspection or maintenance by yourself. Refer all servicing
to qualified personnel.
17 - Operating environment :
Ambient temperature and humidity: +5 - +35°C, relative humidity must be less than
85% (when cooling vents are not obstructed).
Do not operate this product in a non-ventilated, very humid or warm place.
• As HITMUSIC is really involved in the
environmental cause, we only commercialise
clean, ROHS compliant products.
• When this product reaches its end of life,
take it to a collection point designated by local
authorities. The separate collection and recycling
of your product at the time of disposal will help
conserve natural resources and ensure that it is
recycled in a manner that protects human health
and the environment.
ATOM series - 2 ways 10/12/15" powered full range speaker and 15/18" powered subwoofer with DSP
2 - Introduction
The ATOM Series speakers and subwoofers are the ideal solution for your live performances.
With 300W for the ATOM10A, 400W for the ATOM12A, 400W for the ATOM15A, 600W for the ATOM15ASUB
subwoofer and 600W for the ATOM18ASUB subwoofer, the ATOM series products deliver a powerful, clear
and warm sound, suitable for both voice and live or recorded music.
All equipped with an adjustable DSP, the elements of this series allow you to tune the sound reproduction in
an ideal way whatever the configurations of your performances.
Fast installation, lightweight and space-saving, they will quickly become the partners of your nomadic services,
without compromising quality, power or possibilities.
3 - Technical information of the full range speakers
ATOM10A ATOM12A ATOM15A
Bi-amplification
Total power output 1200W dynamic / 300W RMS 1600W dynamic / 400W RMS 1600W dynamic / 400W RMS
Frequency response 60 Hz - 20 KHz 50 Hz - 20 KHz 45 Hz - 20 KHz
Power supply SMPS
H x V Dispersion 90° x 60°
Filter cutoff frequency 2,8 KHz 2,8 KHz 3,4 KHz
250W RMS Class D for LF
50W RMS Class AB for HF
350W RMS Class D for LF
50W RMS Class AB for HF
350W RMS Class D for LF
50W RMS Class AB for HF
Sound Pressure Level 121 dB max. 123 dB max. 124 dB max.
Woofer
Tweeter
Input 1 entrée MIC/LINE1 COMBO XLR/JACK MIC/LINE input / 1 RCA/3.5 mini Jack input
Output 1 XLR line output
Settings Multiple settings DSP (refer to paragraph 5 for more details)
Protection Short-circuit, thermal and limiter
2 monitor-specific 45° angles
1 top handle (ATOM10A / ATOM12A / ATOM15A)
Construction and fastenings
Dimensions 516 x 300 x 291 mm 619 x 360 x 351 mm 778 x 430 x 402 mm
Net weight 13 Kg 17 Kg 21 Kg
1 side handle (ATOM12A et ATOM15A)
2 M10 rigging points (on top)
1 insert M10 derrière
36mm dual positions mounting plate for a speaker stand (0° and 7,5°)
10"
2" coil
4 Ohms - 250W AES
1" compression
8 Ohms
50 W RMS
12"
3" coil
4 Ohms - 350W AES
1,35" compression
8 Ohms
50 W RMS
15"
3" coil
4 Ohms - 350W AES
Page 3
ATOM series - 2 ways 10/12/15" powered full range speaker and 15/18" powered subwoofer with DSP
4 - Module d'amplification des enceintes
7
6
5
4
8
3
1
Power input socket
Allows you to connect the speaker to an electrical outlet.
Use the supplied IEC cord, and make sure the voltage
delivered by the outlet is in adequation with the value
indicated by the voltage selector before turning on the
built-in amplifier.
2
Power switch
Allows you to turn ON/OFF the built-in amplifier.
3
XLR LINE OUT socket
Allows you to retrieve the sum of each incoming signal
and transmit it to another amplified speaker, mixing
desk, or speaker/amplifier system.
4
MIC/LINE input via COMBO plug
The COMBO plug allows you to connect either a male
XLR plug or male stereo/mono Jack plug.
Page 4
2 1
5
LINE/MIC Selector
Allows you to adapt the impedance of the socket to the
type of signal detected.
When pressed, the entry level is adapted to a
microphone, when released it is adapted to a line level
signal.
6
Integrated DSP diplay
Displays the settings of the built-in DSP.
The different settings of the DSP will be explained in
paragraph 5.
7
DSP settings button
Press this button to access the available settings or to
enter the different submenus.
Then turn this knob to scroll through the values of each
sub-menu.
Press again to confirm your settings.
9
10
11
ATOM series - 2 ways 10/12/15" powered full range speaker and 15/18" powered subwoofer with DSP
8
Channel 1 input level
Make sure that the input level is not too high to avoid
distorted sound.
9
Channnel 2 input level 2
Make sure that the input level is not too high to avoid
distorted sound.
10
Auxiliary Input
Stéréo 3.5 jack.
This input is used to connect a tablet, a mobile phone,
an MP3 player,... etc.
11
RCA line input
This input is used to retrieve a signal from a CD player,
a mixer, etc...
ATOM10A/12A/15A input setting
1 - Connect the loudspeaker to the mains via IEC plug / 2-pin + earth. Leave the power switch (2) in the
OFF position.
2 - Set all LEVEL potentiometers (8 and 9) to the -∞ position.
3 - Connect your microphone or line level source or both. L'entrée ligne est accessible par le branchement
The line input can be accessed via a 3-pin 6.35 mm (TRS) jack, RCA LINE IN or AUX input. To acces
to the microphone preamplifier, use the XRL plug
4 - Switch on the line level source.
5 - Switch on the ATOM speaker.
6 - While you are speaking in a microphone or an audio signal is being played from your line-level source,
turn the input level knob (s) until the display shows "Limit Signal", then turn it down just below that
level.
7 - If you use a microphone, be careful not to stand too close to the speaker as this may result in
feedback. If you do not use both inputs, it is recommended that you leave the level knob on the
unused input at the -∞ position to prevent noise from entering the signal circuit.
Page 5
ATOM series - 2 ways 10/12/15" powered full range speaker and 15/18" powered subwoofer with DSP
5 - Full range speaker menu
MENUS MENU OPTION
MODE menu
NORMAL
POLE
HF:0dB
LF:0dB
ATOM 1 0A
LOCATION
TREBLE B
HF:0dB
LF:0dB
MODE
Menu LOCATION
NORMAL
POLE
ATOM 1 0A
LOCATION
Menu TREBLE
NORMAL
POLE
TREBLE BE
HF:0dB
LF:0dB
ATOM10A
BASSTION LED
TREBLE
Menu BASS
NORMAL
POLE
HF:0dB
LF:0dB
ATOM10A
TREBLEON LED RES
BASS
Menu LED
NORMAL
POLE
HF:0dB
LF:0dB
ATOM10A
TREBLE BASS RESET
Menu RESET
NORMAL
POLE
LED
HF:0dB
LF:0dB
ATOM 1 0A
TREBLE BASS LED
Menu INFO
NORMAL
POLE
HF:0dB
LF:0dB
ATOM 1 0A
EBLE BASS LED RESET
RESET
+10
0
-10
Push to Save and Return
Push to Save and Return
+10
0
-10
Push to Save and Return
+10
0
-10
Push to Save and Return
Front Panel LED
is always
"Black Out"
Push to Save and Return
Are you sure ?
Restore the device
to the factory
default settings
Push to Save and Return
ATOM10A
Firmware Ver 2.1.0
Copyright(C) 2018
Audiophony All right reserved
INFO
Push to Return
Normal
Speech
Monitor
Bracket
+6dB
+8dB
YES
This menu is used to select one of the preset :
-NORMAL : The equalisation is flat (default value).
-LIVE : The bass is attenuated and the treble is raised to obtain
Live
Club
Pole
OFF
ON
LIMIT
NO
a "concert"sound.
-CLUB : The bass is slightly raised and the treble slightly atte-
nuated to obtain a warmer sound.
-SPEECH : The bass is very attenuated, the midrange is
slightly raised and the treble is not modified to obtain a more
intelligible sound by the human ear.
This menu allows you to choose the behavior of the speaker
according to how it is positioned.
-POLE : Choose this option when using the speaker on a stand
(default setting).
-MONITOR : Choose this option when using the speaker as a
stage return.
-BRACKET : Choose this option when the speaker is mounted
on a wall mount.
This menu is used to adjust the treble level.
Values range from -10dB to +10dB.
This menu is used to adjust the bass level.
Values range from -10dB to +10dB.
This menu is used to adjust the behaviour of the LED on the front
panel.
OFF : The LED never lights up.
ON : LED is constantly lit in blue.
LIMIT : The LED lights blue and red when the limiter is switched
on.
This menu is used to reset all settings to the original values.
This menu is used to display the internal software version.
Page 6
ATOM series - 2 ways 10/12/15" powered full range speaker and 15/18" powered subwoofer with DSP
6 - Caractéristiques techniques des caissons
ATOM15ASUB ATOM18ASUB
Amplification Class D / 2000W dynamic / 600W RMS Class D / 2000W dynamic / 600W RMS
Frequency response 45 Hz - 160 KHz 35 Hz - 150 KHz
Power supply SMPS / 100-240V ~ 50-60Hz
SPL 126 dB max. 127 dB max.
Woofer
Entrées 2 x COMBO 6.35 XLR
Sortie 2 XKR output
Réglages multiple settings DSP (refer to paragraph 8 for more details)
Protection Short-circuit, thermal and limiter
Construction et accrochages
Dimensions 612 x 430 x 595 mm 662 x 510 x 615 mm
Poids net 32 Kg 38 Kg
15"
18"
8 Ohms - 600W AES
35mm mounting plate for speaker coupling rod
5mm Cubic plywood housing
Integral grid
2 side handles
Ground stacking device
18"
Bobine de 3"
8 Ohms - 600W AES
7 - Subwoofer amplifier modèle
1
Sorties 1 et 2
3 4
These line level outputs are used to retrieve the input
signals and re-inject them to another amplification
system (see OUTPUT menu on page 8).
Output 1 corresponds to input 1 and output 2
corresponds to input 2.
12
Note : The power input and power button are the
same as on the full range speakers.
2
Entrée 1 et 2
Line-level left and right inputs via COMBO sockets.
COMBO sockets allow you to either connect a mono/
stereo male XLR or male Jack plug. These are balanced
inputs.
3
Integrated DSP diplay
Displays the settings of the built-in DSP.
The different settings of the DSP will be explained in
paragraph 8.
4
DSP settings button
Without pressing this button, you adjust the subwoofer
level.
Press this button to access the available settings or to
enter the different submenus.
Then turn this knob to scroll through the values of each
sub-menu.
Press again to confirm your settings.
Page 7
ATOM series - 2 ways 10/12/15" powered full range speaker and 15/18" powered subwoofer with DSP
8 - Subwoofers DSP Menu
MENUS MENU OPTIONS
LEVEL menu
NORMAL
NORMAL
MODE menu
NORMAL
NORMAL
150 Hz
NONE
ATOM15ASUB
LOCATION DELAY
MODE
Menu LOCATION
NORMAL
POLE
HF:0dB
LF:0dB
ATOM15ASUB
LOCATION
Menu DELAY
NORMAL
NORMAL
150 Hz
NONE
ATOM15ASUB
POLARITY XTION
DELAY
Menu POLARITY
NORMAL
NORMAL
150 Hz
0.25 m
ATOM15ASUB
POLARITY
Menu X-OVER
NORMAL
NORMAL
150 Hz
0.25 m
ATOM15ASUB
NORMAL
NORMAL
X-OVER
150 Hz
0.25 m
Menu OUTPUT
ATOM15ASUB
OUTPUT
150 Hz
NONE
ATOM15ASUB
+10
0
-10
Push to Save and Return
DELAY PODE
Push to Save and Return
Push to Save and Return
X-ODELAY
Push to Save and Return
OUTPUOLARITY
Push to Save and Return
UNX-OVERY
Push to Save and Return
0 dB
Normal
Enforce
Normal
Cardioid
Endfire
0.25m
Normal
Reverse
150Hz
100 Hz
This menu appears when the subwoofer is initialized and allows
you to adjust the subwooer's amplification level.
It is not necessary to press the button to make this setting.
The value varies from MUTE (no amplification) to +10dB.
This menu allows you to choose the behavior of the cabinet
according to how it is positioned.
-NORMAL : Choose this option when using the cabinet in front
of the sound system.
-ENFORCE :Choose this option when using the cabinet in front
of the sound system.
This menu allows you to optimize the response of ATOM15S and
ATOM18S when used alone or in groups.
-NORMAL : Choose this option when using the subwoofer in
nongroup mode.
-CARDIOID : Choose this option for a cardioid effect with the
pedestals in grouped mode.
-ENDFIRE : Choose this option when using two subwoofers in
longitudinal radiation one behind the other.
This menu allows you to add a delay time to the subwoofer to
align it over time.
The value of the delay is expressed in metres.
By default no delay time is applied.
This menu allows you to reverse the polarity of the sum of the
signals present at the input..
This menu is used to set the upper limit of the frequency range of
the subwoofer. The optimum setting is the minimum value of the
frequency range correctly reproduced by the full range speakers.
Among the available values for this setting you will find each of
the ATOM series full range speakers.
This menu is used to set the low limit of the frequency range sent
to outputs 1 and 2.
Page 8
ATOM series - 2 ways 10/12/15" powered full range speaker and 15/18" powered subwoofer with DSP
Menu UNIT
NORMAL
NORMAL
ATOM15ASUB
Menu UNIT
NORMAL
NORMAL
ATOM15ASUB
Menu RESET
NORMAL
NORMAL
ATOM15ASUB
Menu INFO
NORMAL
NORMAL
ATOM15ASUB
UNIT RESETOUTPUTR
150 Hz
0.25 m
UNIT
150 Hz
0.25 m
LED
150 Hz
0.25 m
LEDUNITOUTPUT
RESET
150 Hz
0.25 m
RESETLEDUNITUT
Use "Meter(m)"
as the unit of
the "DELAY"
LED REOUTPUTVER
Push to Save and Return
Front Panel LED
is always
"Black Out"
Push to Save and Return
Are you sure ?
Restore the device
to the factory
default settings
Push to Save and Return
ATOM15ASUB
Firmware Ver 2.1.0
Copyright(C) 2018
Audiophony All right reserved
INFO
Meter(m)
Feet(ft)
OFF
ON
LIMIT
YES
NO
This menu allows you to select the unit used by the DELAY menu
: meter or foot.
This menu is used to adjust the behaviour of the LED on the front
panel.
OFF : The LED never lights up.
ON : LED is constantly lit in blue.
LIMIT : The LED lights blue and red when the limiter is switched
on.
This menu is used to reset all settings to the original values.
This menu is used to display the internal software version.
Different positions of the LOCATION menu
Normal
Cardioid
Endfire
Page 9
ATOM series - 2 ways 10/12/15" powered full range speaker and 15/18" powered subwoofer with DSP
9 - Principle diagram
15A 15A
18ASUB
Page 10
12A12A
ATOM series - 2 ways 10/12/15" powered full range speaker and 15/18" powered subwoofer with DSP
10 - Connectors
10.1 - Balanced
The COMBO sockets are
symetrical. This type of
connectors allows you to transmit
a signal over long runs of cables
without altering its quality, that
is why we recommend to use
symetrical signals.
The figures opposite describe
the balanced wiring of the XLR or
Jack 6.35 plugs.
10.2 - Unbalanced
1
2
3
3 = Coldspot (-)
1 = Ground
2 = Hotspot (+)
Sleeve
Ring
Tip
Sleeve
Ground / Shield
Ring
Coldspot (-)
Hotspot (+)
Tip
If you do not have any source
with symetrical signal, please do
not use cables longer than 1.5 m.
The figures opposite describe the
unbalanced wiring of the XLR or
Jack 6.35 plugs.
1
3
Shunt between
1 and 3 pins
2
1 = Ground
2 = Hotspot (+)
Sleeve
Tip
Sleeve
Ground / Shield
Tip
Signal
Page 11
Because AUDIOPHONY® takes the utmost care in its products to make sure you only get the best possible quality, our products are
subjects to modifications without prior notice. That is why technical specifications and the products physical configuration might differ
from the illustrations.
Make sure you get the latest news and updates about the AUDIOPHONY® products on www.audiophony.com
AUDIOPHONY® is a trademark of HITMUSIC S.A.S - Zone Cahors sud - 46230 FONTANES - FRANCE
Loading...