Page 1
Product Installation Manual
r L
Compact Disc Player / AM-FM Tuner
Model No.: RCD-022-01-x
Document #540107
7300 Industry Drive, North Little Rock, AR 72117
Phone: 501-955-2929 Fax: 501-955-2988
Page 2
AUDIO INTERNATIONAL, INC. 4/98
Revision History
Rev. Level
IR 4/98 Initial Release
Date Description
Applicable Documents
Document # Drawing
#
N/A 522144 RCD-022-01-x CD Player/AM-FM Tuner
560027 N/A Operation’s Guide
Description
2
Document #540107, Rev. IR, Model No.: RCD-02201-x
Page 3
AUDIO INTERNATIONAL, INC. 4/98
Service Bulletin List
Service
Bulletin #
Subject Manual
Revision
#
Manual
Revision
Date
Section
No.
List of Illustrations
Description Page #
3
Document #540107, Rev. IR, Model No.: RCD-02201-x
Page 4
AUDIO INTERNATIONAL, INC. 4/98
Table of Contents
Section Description Page
1.0
General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.2 Purpose of the Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.3 Operational Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.4 Optional Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.0
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.1 Prior to Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.2 Unpacking & Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.3 Cautions & Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.4 Wiring Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.5 Physical Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.6 Electrical Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.7 Pinouts / Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.8 Connector / Mating Connector Information . . . . . . . . . . . . . . . . . . . . . . . 9
2.9 Post Installation Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.0
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.1 CD Player Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.2 Radio Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
4.0
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
5.0
Specification and Drawings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
5.1 Unit Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
5.2 Applicable Drawings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 11
PROPRIETARY NOTICE: Despite any copyright notice, this data and information disclosed herein is
unpublished and contains confidential, proprietary design owned by Audio International Incorporated.
Neither this data nor the data contained herein shall be reproduced, used or disclosed to anyone
without the written authorization of Audio International Incorporated.
4
Document #540107, Rev. IR, Model No.: RCD-02201-x
Page 5
AUDIO INTERNATIONAL, INC. 4/98
MODEL NO.
RCD-022-01-x
CD Player / AM-FM Tuner
1.0 General Information
1.1 Introduction
This manual contains information for the installation of the Audio International,
Inc. (AI) CD Player / AM-FM Tuner, Model No. RCD-022-01-x. The “x” suffix
in the number designates the specific model purchased. Information contained
within this publication includes relative physical, mechanical, and electrical
characteristics. Also included within this publication are additional references
needed for installation of the unit.
1.2 Purpose of the Equipment
The RCD units are high quality AM-FM compact disc players specifically
designed to meet the special requirements of aircraft use. These units allow
complete control of track selection. Features include track search, track repeat,
track scan and random play mode. The units have high quality output, adjustable
stereo output level from 1 to 5 volts RMS, and full range frequency response of
20Hz to 20kHz (+/-1dB).
These compact disc players can be mounted in a cabinet or in a bulkhead. AI
source equipment can be optionally controlled by infrared remote. A unique
strapping feature allows up to four (4) similar devices to be used in the same
system at the same time while maintaining independent control.
1.3 Operational Features
Operational features of the units include a backlit LCD indicator display along
with a user controllable keypad interface. Additionally, the units are infrared
remote control capable and will interface with AI proprietary RS-485 data bus.
1.4 Optional Equipment
The front bezel of the RCD can be customized to match the interior style of any
aircraft. This includes plating and painting to match aircraft interiors.
AI source equipment is configured to accept digital infrared commands. Digital
codes allow the source equipment to interface with an infrared handheld remote
control (AI-RC1-17xxxx) via infrared receiver, IFR-9A. Multiple units can be
controlled independently using available programming pins. The infrared code
allows up to four (4) similar devices to be used in the same system while
maintaining independent control. To install multiple units, contact Audio
International, Inc.
5
Document #540107, Rev. IR, Model No.: RCD-02201-x
Page 6
AUDIO INTERNATIONAL, INC. 4/98
2.0 Installation
2.1 Prior to Installation
The RCD is a simple AM-FM compact disc player to use and install. The RCD is
capable of accepting infrared digital input and/or RS-485 two-wire digital data
bus input. All audio input and output cables on the unit should be twisted
shielded pair (24 AWG minimum) unless otherwise specified. The unit must be
attached to conform to the standards designated by the customer, installing
agency, and existing conditions as to the unit location and type of installation.
The following should be carefully considered before installation:
2.1.1 Select a mounting location for the unit where 28 VDC power and audio
signal has been previously installed. Long low-level audio runs may
introduce noise into the audio signal. Refer to Section 5.0 Specifications
and Drawings for location of mounting points.
2.1.2 Locate the unit to allow easy audio level adjustments. Level adjustment
controls are located on the rear of the unit. These adjustment level
controls must be accessible for periodic system adjustments.
2.1.3 All headphone amplifiers and line level amplifiers should be located no
more than three feet away from source equipment.
2.1.4 Avoid installing the unit where it will be exposed to excessive heat,
excessive moisture, splashing liquids, dusty areas, direct sunlight, or
angled/inclined installations.
2.1.5 A minimum of 5.0 inch clearance is required in front of the CD slot.
When the CD is ejected, it will project approximately 2.25 inches.
2.2 Unpacking & Inspection
2.2.1 Carefully open the packaging and remove the compact disc player / AM-
FM Tuner. Verify that all components have been included in the package
per the packing list. Inspect the unit for damage. Retain the packing
materials and packing list. The components should arrive in good
condition.
If damage has occurred during shipping, a claim must be filed with AI
within 24 hours and a “Return Request Authorization Number” must be
obtained from AI. Refer to the front cover of this manual for address and
telephone number of Audio International, Inc. Repackage the unit in its
original packaging materials and return it to AI following instructions
given by the AI representative. If no return is necessary, retain the
packing materials for storage or reshipment if necessary.
6
Document #540107, Rev. IR, Model No.: RCD-02201-x
Page 7
AUDIO INTERNATIONAL, INC. 4/98
2.3 Cautions & Warnings
2.3.1 All audio connections to the RCD should be shielded and properly
grounded at the source. Perform a pin-to-pin check to confirm that all
wires terminate in their proper location. It is important to do a power and
ground check on the pin connections. Ensure that power and ground are
applied only where required.
2.3.2 DO NOT connect or disconnect the unit while power is applied.
2.3.3 DO NOT remove any factory-installed screws. Damage to the unit may
result and void any warranties.
2.4 Wiring Requirements
2.4.1 The installing agency must supply and fabricate all external cables. The
length and routing of external cables must be carefully studied and
planned before attempting installation of the equipment. Allow adequate
space for installation of cable and connectors. Avoid sharp bends and
placing cables near aircraft control cabl es. Maintain a mi nimum clearance
of three (3) inches from any control cable. If wiring is run parallel to
combustible fluid or oxygen lines, maintain a separation of six (6) inches
between the lines.
2.4.2 All power and ground wires must be 24 AWG minimum. All audio lines
require twisted, shielded cable with the cable shields grounded. Power
ground wires must be grounded within twelve (12) inches of the unit. All
wires must be in accordance with MIL-W-22759 or equivalent. Twisted,
shielded cable must be in accordance with MIL-W-27500 or equivalent.
Protect power wires with circuit breakers or fuses located close to the
electrical power source bus.
2.4.3 The RCD-022-01-x is designed to interface with other AI equipment via
the proprietary RS-485 data bus. This is a bi-directional data bus that
allows multiple units to be connected simultaneously. The lines are daisychained between units with 120-ohm resistors installed at both ends of the
wiring harness. Cable designed specifically for data bus use with 120ohm nominal impedance should be utilized. Contact Audio International
for recommended cables.
2.5 Physical Requirements
Refer to Section 5.1 for unit dimensions and mounting attachment points.
7
Document #540107, Rev. IR, Model No.: RCD-02201-x
Page 8
AUDIO INTERNATIONAL, INC. 4/98
2.6 Electrical Requirements
2.6.1 The RCD-022-01-x utilizes one 15-pin connector for electrical
connections. This connector provides 28 VDC, left/right audio output,
data bus control, infrared input and four (4) strapping pins for alternate
configuration of infrared digital command codes.
2.6.2 The RCD-022-01-x utilizes one BNC connector for antenna high and
antenna shield.
2.6.3 Standard configuration requires no infrared strap pins to be connected.
Each different type of AI source equipment can be configured to accept
one of four (4) different sets of infrared codes. To change the code
settings, connect one (1) of the strap pins to the strap common (never
connect more than 1 strap pin to the strap common). Three (3) strap pins
are available to allow the infrared codes to be configured.
2.7 Pinouts / Descriptions
The RCD-022-01-x unit connector with its respective pins and descriptions is as
follows:
1 +28 VDC Power
2 Ground
3 R+ Audio Output
4 R- Audio Output
5 L+ Audio Output
6 L- Audio Output
7 Data bus (A)
8 Data bus (B)
9 Infrared Input +
10 Infrared Input 11 IR Strap 2
12 IR Strap 3
13 IR Strap 4
14 IR Strap Common
15 Reserved
BNC Antenna High
Antenna Shield
Pin # Description
8
Document #540107, Rev. IR, Model No.: RCD-02201-x
Page 9
AUDIO INTERNATIONAL, INC. 4/98
2.8 Connector / Mating Connector Information
Mating connector part numbers are as follows:
Model # Connector Mating Connector
RCD-022-01-1
RD15M10JV30 RD15F10JVL0
RCD-022-01-2
Antenna BNC
DAMA-15P DAMA-15S
D20418-2 Female Screw Lock
Amphenol 413779-4
2.9 Post Installation Test
2.9.1 The audio signal output of the unit is generally connected to cabin speaker
systems in addition to headphone locations. It is important to verify that
all equipment has been set to the recommended initial settings. Verify all
connections before supplying power to the unit.
2.9.2 Utilize the front panel controls to turn “ON” the AM/FM tuner. Utilize
the AM/FM random search button to select a desired radio station. Verify
that the station can be heard through the speaker and/or headphone system.
2.9.3 Load the CD player with selected material. Verify that the RCD
automatically plays back the selected CD. Use the front panel controls or
the hand-held remote control unit to select track search, PLAY, PAUSE,
EJECT, etc. Verify that all functions are operational. Verify that the RCD
audio can be heard through the speaker and/or headphone system.
3.0 Operation
3.1 CD Player Operation
Load the CD player with selected material. The unit will automatically begin
playing the CD. Verify that the select ed material may be heard. The output level
gain adjustment potentiometers on the rear of th e unit are preset at the factory to
2V RMS. Contact AI if adjustments are needed. If a CD is in the unit, and power
is removed, the CD m ust be ejected and reinserted to resume play once power is
reapplied.
3.2 Radio Operations
To operate the AM/FM radio, apply power to the unit by turning the tuner power
to the “ON” position. Use the AM/FM random search button to select the desired
radio station. The station numbers will appear in the digital window as they are
“tuned” in.
9
Document #540107, Rev. IR, Model No.: RCD-02201-x
Page 10
AUDIO INTERNATIONAL, INC. 4/98
4.0 Troubleshooting
Problem Possible Cause Solution
No sound RCD is improperly installed
No audio material in source unit.
Poor audio quality Audio controls are not adjusted
properly.
Poor Tuner reception Antenna connection may be
faulty
Verify 28 VDC power and audio
output is present
Insert audio material in source
unit
Adjust output level.
Verify antenna co nnections
5.0 Specifications and Drawings
5.1 RCD Unit Specifications
Housing Black Anodized Brushed Aluminum
Dimensions Length-7.38”, width-8.09”, height-2.3 0”
Weight Approximately 4.0 lbs.
Physical Specifications
Power 650mA at 28 VDC (playing)
Audio Output 1 V RMS to 5 V RMS adjustable (4K-ohms min.)
Data bus Type RS-485
Digital Filter (D/A) 8 times over-sampling
Frequency Response 20 Hz to 20 kHz (+/-1 dB)
Total Harmonic Distortion 0 . 0 1% (1 kHz)
Signal to Noise Ratio 93 dB
Dynamic Range 93 dB
Channel Separation 85 dB
Frequency Range 87.9 MHz – 107.9 MHz
Channel Space 200 kHz
Usable Sensitivity (S/N=30dB)
Frequency Response 30 Hz to 15 kHz (+/-3 dB)
Signal to Noise Ratio 75 dB (MONO)
Stereo Separation 40 dB (1 kHz)
Frequency Range 530 kHz – 1700 kHz
Channel Space 10 kHz
Usable Sensitivity
Electrical Specifications
750mA at 28 VDC (ejecting CD)
CD Player Specifications
FM Tuner Specifications
9.3 dBf (0.8 µ V/75-ohms)
AM Tuner Specifications
23 dB (25 µ V)
10
Document #540107, Rev. IR, Model No.: RCD-02201-x
Page 11
AUDIO INTERNATIONAL, INC. 4/98
5.2 Applicable Drawings:
5.2.1 The following diagram shows an exaggerated view of the front panel of
the RCD unit.
5.2.2
5.2.3 The following diagram shows the top view of the RCD with unit
dimensions.
11
Document #540107, Rev. IR, Model No.: RCD-02201-x
Page 12
AUDIO INTERNATIONAL, INC. 4/98
5.2.4 The following is a reduced diagram showing the side and rear views of the
unit showing the ball stud location and unit dimensions.
12
Document #540107, Rev. IR, Model No.: RCD-02201-x
Loading...