Audiodesign PAMX3.82, PAMX3.122 Owner's Manual

OWNER MANUAL

PROFESSIONAL MIXER

PAMX3.82 - PAMX3.122

DI FFUSO RI, AMP LI FICAT OR I PROFE SS IONAL I E ACCES SO RI

Audiodesign Srl Via dell’industria, 28 - 42025 CAVRIAGO (RE) +39 0522 941444 - Fax +39 0522 942363 www.audiodesign-pro.com info@audiodesign.it

MIC IN------MAIN OUT L/R

76dB

@620ohm Load, balanced

MIC IN------REC OUT

60dB

@10Kohm Load

ST LINE IN------MAIN OUT L/R

26dB

MIC IN------L/R,SUB,AUX OUT

70dB

@620ohm Load, unbalanced

MIC IN------EFF OUT

74dB

@620ohm Load

AUX RET------MAIN OUT L/R

28dB

Max gain

Signal route

Conditions

@620ohm Load, balanced @620ohm Load, balanced

2 TK IN ------MAIN OUT L/R

28dB

@620ohm Load, balanced

4 1 1

150ohm

75ohm

10Kohm

+10dB

-10dB

+4dB

75ohm

+4dB

100ohm

3mW @36ohm

75ohm

+4dB

75ohm

+4dB

Outputs

Number

Outputs modes

AUX SEND

Stereo REC OUT HEADPHONE

Balanced

Unbalanced

Stereo out

Connector

2 RCA

3-poles TRS

Stereo MAIN OUT

Unbalanced Unbalanced Unbalanced Unbalanced

2 TRS

2 XLR

EFF SEND

SUB OUT

Stereo MAIN OUT

2 TRS 4 TRS

2-poles TRS

Output level

Rated

Impedance

Outputs

6/10

2Kohm

47Kohm

10Kohm

-60dB

-40dB

-10dB

10Kohm -10dB

Unbalanced

Balanced

Input modes

Number

Connector

2 TRS

3-poles TRS

XLR

2 RCA+2 TRS

Inputs

Microphones

Mono LINE IN

Stereo LINE IN B Stereo AUX RET

Stereo LINE IN A

10Kohm -10dB

Unbalanced

2 RCA

Stereo PLAY IN

3-poles TRS

Input level

Rated

Input

Impedance

Channel EQ HI 12KHz MID 2.5KHz LOW 80Hz max equalizing value +/-15dB

Main Graphic EQ 63,125,250,500Hz,1,2,4,8,16KHz max equalizing value +/-12dB

Effect Processor 99 effect DSP

<0.1% @+14dB 20~20000Hz 620ohm loadTotal harmonic distortion

+1/-2dB @+4dB 20~20000Hz 620ohm load

Frequency response

+20dB/+26dB<balanced> @0.5%THD 1KHz 620ohm load Max out level

-124dB @ 150ohm , at max gainMicrophone preamp E.I.N

PAGE 15

Introduction/Features … …

Precautions…… ……… ………… …… ……… …… …… 3

Mono channel section … … …… … … … …… … 4

The stereo channel(A) … … … … … … … … … … 5

The stereo channel(B) … … … … … … … … … … 9

Master control section… … …… … … … … … … … 7

Set up MEMO…… ……… ……… …… …… …… …… 10

Effect List… … … … … … …… … … … …… … … … 11

Connection cables…… …… …… ……… ……… …… 12

System block diagram…… …… …… …… …… …13

Application example… …… … … …… … … … …… 14

Specifications …… …… ……… ……… …… …… ……15

… … …… … … …… … … 2

PAGE 2

35VA

45VA

412x372x86

518x372x86

PAMX3.82

PAMX3.122

Power Power consumption Weight (Kg) Dimensions(mm)

Type

INTRODUCTION / FEATURES

Welcome you using the this series portable mixer. These mixers have handsome outline, perfect functions.

It is easy to schlep or operate. It has two group outputs and 4 AUX output and it is suitable for a wide variety of input sources.

There is a effect processor with in the unit, it must be a ideal equipment you need.

Please read this manual carefully to know all functions and operations of the products well, in order to operate the unit at the good condition.

FEATURES

6 or 10 mono input channels and 4 stereo input channels(2 among 4 stereo input channels are also used as microphone's input).

2 auxiliary inputs and 4 auxiliary outputs.

With INSERT function for Mono input channel

Adopt low-noise discrete Mic pre-amplifier on all microphone inputs, 3-band frequency equalizer for each input channel.

Built-in +48V phantom power for condenser microphone.

Signal and peak indicators on each input channel.

Real two groups output, 60mm slide fader.

4 groups of 12 LED level meter to show the main out level and the groups out Level.

4 groups of 4 LED level meter to show the 4 AUX out Level.

9-band stereo graphic EQ.

Volume control for headphone out.

Stereo record out and stereo in for tape play.

An effector outside can be linked.

CONTENTS

SPECIFICATIONS

NOTICEINS TRU CTI ON

1.Check the AC voltage before connecting the AC plug. Proper grounding is a necessary practice to prevent electric shock hazards to the operator, the microphone user, and the musicians who are wired to this unit.

2.Before switching on the main power, keep all the output fader all the way down to prevent damage or excessive noise caused by bad level adjustment, wrong wiring, defective cables or bad connection.

3.Always turn on the mixer before the power amplifier; turn off the mixer after the amplifier.

4.Always turn off the unit before connecting and disconnecting the unit from the power source.

5.Never use solvents to clean the unit. Clean with a soft, dry cloth.

AC110 V;120 V;220 V; 230V R efer to t he labe l on the ba ck pane l

PR OFESS IONAL MIX ER

Serie PAMX3

PR OFESS IONAL MIX ER

Serie PAMX3

PAGE 3PAGE 14

CONNECTION EXAMP LE

1. Read all safety and operating instructions before using this product.

2. All safe ty and operating instructions should be kept for future reference.

3. Read and understand all warnings listed on the operating instructions.

4. Follow all operating instructions to operate this product.

5. This product should not be used near water , i.e. a bathtub, sink, swimming pool, wet basement, etc.

6. Use only a dry cloth to clean this product.

7. Do not block any ventilation openings. The product should not be placed fat against a wall or placed in a built-in enclosure that will impede the fow of cooling air.

8. Do not install this product near any heat sources, such

as radiators, heat registers, stoves or any other apparatus (including heat–producing amplifers) that produces heat.

9. Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not ft into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord being walked on or pinched,

particularly at plugs, convenience receptacles and the point where they exit from the apparatus. Do not break the ground pin of the power supply cord.

11. Only use attachments specifed by the manuf acturer.

12. Use only with the cart, stand, tr ipod, bracket,

or table specifed by the manufacturer or sold with the apparatus. When a cart is used, use caution when moving cart/ apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when

unused for long periods of time.

14. Care should be taken so that objects do not fall and liquids

are not spilled into the unit through the ventilation ports or any other openings.

15. Refer all servicing to a qualifed service professional. Ser vic

ing is required when the apparatus does not operate normally or has been damaged in any way, including damage to the power cord or plug, damage due to liquids spilled or objects dropped inside the unit, dropping the unit, or anything else that interrupts normal use of the unit.

16. WARNING: To reduce the risk of fre or electric shock, do not

expose this apparatus to rain or moisture.

17. When a mains plug is used as the disconnect device, the disconnect device shall remain readily operable.

Important Safety Instructions

Exposure to extremely high noise levels may cause permanent hearing loss. Individuals vary considerably to noise-induced hearing loss but most will lose some hearing if exposed to intense noise for a suffcient period of time.

DANGER

THIS SYMBOL IS INTENDED TO ALERT THE USER TO THE PRESENCE

OF NON-INSULATED “DANGEROUS VOLT AGE” WITHIN THE PRODUCT’S ENCLOSURE THAT MAY BE OF SUFFICIENT MAGNITUDE TO CONSTITUTE A RISK OF ELECTRIC SHOCK TO PERSONS

THIS SYMBOL IS INTENDED TO ALERT THE USER TO THE PRESENCE OF IMPORTANT OPERATING AND MAINTENANCE (SERVICING) INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THE UNIT .

APPARATUS SHALL NOT BE EXPOSED TO DRIPPING OR SPL ASHING AND THAT NO OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES,

SHALL BE PLACED ON THE APPARATUS.

SAFETY INSTRUCTI ONS

Conne cti on ex amp le

PR OFESS IONAL MIX ER

Serie PAMX3

PR OFESS IONAL MIX ER

Serie PAMX3

EFFECT PROCESSOR

REC OUT L/R

LINE IN L/RLINE IN L/RMIC IN

Eff Send

AUX Ret

SUB OUT

HEAD PHONES

MIC IN

RIGHT

LEFT

POWER AMP

ST. MAIN OUT L/R

LINE LINE LINE LINE LINE LINE LINE LINE LINE LINELINE

MIC1 MIC2 MIC3 MIC4 MIC5 MIC6 MIC7 MIC8

MIC9

MIC10

GAIN

GAIN GAIN GAIN GAIN GAIN GAIN GAIN

GAINGAIN

LOW CUT

-10 -10 -10 -10 dB dB dB dB

HI HI HI HI HI HI HI HI HI HI HI HI

MID MID MID MID MID MID MID MID MID MIDMID MID

LOW LOW LOW LOW LOW LOW LOW LOW LOW LOW LOW LOW

AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1

AUX2 AUX2 AUX2 AUX2 AUX2 AUX2 AUX2 AUX2 AUX2 AUX2 AUX2 AUX2

AUX3 AUX3 AUX3 AUX3 AUX3 AUX3 AUX3 AUX3 AUX3 AUX3 AUX3 AUX3

AUX4 AUX4 AUX4 AUX4 AUX4 AUX4 AUX4 AUX4 AUX4 AUX4 AUX4 AUX4

EFF EFF EFF EFF EFF EFF EFF EFF EFF EFF

PAN PAN PAN PAN PAN PAN PAN PAN BAL BAL BAL BAL

RLR

LRL

ST LINE 15/16

ST LINE 13/14

REC OUT

BALANCED BALANCED

2TK IN

AUX1

L/MONO

AUX SEND

AUX RET

+12

1KHz 2KHz 4KHz

8KHz

16KHz500Hz250Hz125Hz63Hz

MAIN L

MAIN R/PFL

SUB 1 SUB 2

1 GROUND

2 HOT (+)

3 COLD ( )

SUB2 OUT PHONESSUB1 OUT

MAIN R OUT EFF SENDMAIN L OUT

PFL

MAIN SUB AUX1/2

AUX3/4

EFF TO PHONES SELECTOR

+20

+60

+20

+60

+20

+60

+20

+60

+20

+60

+20

+60

+20

+60

+20

+60

+20

+60

+20

+60

-15 +15 -15 +15 -15 +15 -15 +15 -15 +15 -15 +15 -15 +15 -15 +15 -15 +15 -15 +15 -15 +15 -15 +15

-15 +15 -15 +15 -15 +15 -15 +15 -15 +15 -15 +15 -15 +15 -15 +15 -15 +15 -15 +15-15 +15 -15 +15

-15 +15 -15 +15 -15 +15 -15 +15 -15 +15 -15 +15 -15 +15 -15 +15 -15 +15 -15 +15 -15 +15 -15 +15

0100100100100100100100100100100100

0100100100100100100100100100

LRLRLRLRLRLRLRLRLRLRLRL

PK PK PK PK PK PK PK PK PK PK PK PK

SIG SIG SIG SIG SIG SIG SIG SIG SIG SIG SIG SIG

0100100100100

MAIN OUT

AUX2

AUX3

AUX4

MAIN

SUB AUX1/2

AUX3/4

EFF SEND 2TK IN AUX RETEFF LEVEL PHONES

STEREO GRAPHIC EQUALIZER

POFESSI ONAL MI XER

OUTPUT LEVEL INDICATOR

+48V +48V

MICMIC

ST ST

9/10

11/12

PFL

DSP EFFECTS PROCESSOR

MUTE

PHANTOM PHA NTOM

+10

-2

-4

-7

-20

-10

-30

CLIP

+10

-2

-4

-7

-20

-10

-30

PFL PFL PFL PFL PFL PFL PFL PFL PFL PFL PFL PFL

SUB SUB SUB SUB SUB SUB SUB SUB SUB SUB SUB SUB

MAIN MAIN MAIN MAIN MAIN MAIN MAIN MAIN MAIN MAIN MAIN MAIN

10 10 10 10 10 10 10 10 10 10 10 10

-50 -50 -50 -50 -50 -50 -50 -50 -50 -50 -50 -50

-30 -30 -30 -30 -30 -30 -30 -30 -30 -30 -30 -30

-20 -20 -20 -20 -20 -20 -20 -20 -20 -20 -20 -20

-15 -15 -15 -15 -15 -15 -15 -15 -15 -15 -15 -15

-10 -10 -10 -10 -10 -10 -10 -10 -10 -10 -10 -10

3 4

5 6

11/12

-50

-30

-20

-15

-10

PK PK PK PK PK PK PK PK PK PK PK PK

SIG SIG SIG SIG SIG SIG SIG SIG SIG SIG SIG SIG

CLIP CLIP CLIP CLIP

+6 +6 +6 +6

0 0 0 0

-20 -20 -20 -20

10 10 10 10

-50 -50 -50 -50

-30 -30 -30 -30

-20 -20 -20 -20

-15 -15 -15 -15

-10 -10 -10 -10

AUX1 AUX2 AUX3 AUX4

MAIN

SUB

9/10

15/16

13/14

0 0 0 0 0 0 0 0 0 0 0 0

0 0 0 0

-50

-30

-20

-15

-10

RIGHT

LEFT

POWER AMP

AUX 1 AUX 2 AUX 3 AUX 4

PAGE 13PAGE 4

LINE

MIC1

GAIN

LOW CUT

MID

LOW

AUX1

AUX2

AUX3

AUX4

EFF

PAN

PFL

SUB

MAIN

-50

-30

-20

-15

-10

+20

+60

-15 +15

SIG

SYSTEM BLOCK DIAGRAMS

System block diagrams

CONTROL PANEL

Mono channel section

LOW CUT Switch:

Press this switch, can dacay the input si gnal under 75Hz.

LINE Input：

This is a balanced/unbalanced jack for linking a line level source, input level range: 40~0dB

MIC Input

This is an XLR type connector for microphone, the input level range: -60~-20dB. This connector can offer +48V phantom power for condenser microphone when the phantom power switch is on.

GAIN:

Use this knob to adjust the level of the inpu t signal to the optimal level. For the best balance of S/N ratio and dynamic range, a djust this knob so that the peak indicator 12 lights occasionally.

HI :

This knob control the frequency equal izer at higher frequency point. Max adjust range： 15dB @ 12KHz±

MID

This knob control the frequency equal izer at middle frequency point. Max adjust range: ±15dB @ 2.5KHz

LOW:

This knob control the frequency equal izer at lower frequency point. Max adjust range: ±15dB @ 80Hz

AUX1,AUX2,AUX3,AUX4:

These 4 parts are all set in front of the channel fader, so they are not dependent on the fader

knobs are used for controlling the signal level feed to AUX1~4 bus, these 4

EFF:

This knob is used for controlling the sig nal level feed to EFF bus, it has been set after the channel fader, so it is enslaved to the fader positio n. Adjust th ese knobs when you use effector on this channel.

PAN :

This konb is used for distributing the si gnal level of the channel feed to L/R buses. They are equal which are feed to bus when the kn ob locates in the middle .

CHANNEL FADER:

This fader controls the output level feed to main bus from the input channel, adjusting the volume balance between channels. Faders of channels not in use should be pulled down.

SIG,PEAK Indicador:

These two LED indicators detect the sig nal level which exists at the end of the channel but in front of the channel fader. SIG LED flashi ng means the channel is in normal, and PEAK LED will be light at 6dB befo re clipping to remind that the signal level is too strong to the unit will be overl oad.

PFL :switch

This switch allows you to monitor the sig nal of the input channel, the signal is sampled in front of the channel fader, so it has nothing to d o with the fader position.

SUB,MAIN channel output control:

These two switches control if the chann el signal will feed to the SUB and MAIN bus or not separately. The switch should be turned off for unused channe ls.

PR OFESS IONAL MIX ER

Serie PAMX3

PR OFESS IONAL MIX ER

Serie PAMX3

PAGE 5

CONTROL PANEL

PAGE 12

REAR PANEL/CONNECTION CABLES

UNBALANCED INPUTS

SHIELD

+ SIGNAL

BALANCED INPUTS

- SIGNAL

SHIELD

+ SIGNAL

INSERTS

SEND

SHIELD

RETURN

BALANCED MIC INPUT

PIN1: SHIELD PIN2: + SIGNAL PIN3: - SIGNAL

LINE

MIC9

GAIN

-10 dB

MID

LOW

AUX1

AUX2

AUX3

AUX4

EFF

BAL

+20

+60

-15 +15

SIG

MIC

9/10

PFL

SUB

MAIN

-50

-30

-20

-15

-10

SIG

9/10

1~4 channel

+48V

PHANTOM

5~8 channel

+48V

PHANTOM

CH1 INSERT

CH2 INSERT

CH3 INSERT

CH4 INSERT

CAUTION: FOR CONTINUED

PROTECTION AGAINST RISK OF FIRE REPLACE WITH SAME TYPE AND VALUE FUSE INDICATED.

WARNING: TO REDUCE THE RISK

OF FIRE OF ELECTRIC SHOCK, DO NOT EXPOSE HIS APPLIANCE TO RAIN OR MOISTURE.

POWER

FUSE: T0.5A

NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

USE ONLY WITH 250V FUSE

CH1~CH4 INSERT:

These four INSERT are a break point in the input channel signal path. It allows the signal to be taken out from the mixer, through an external equipment such as a compressor, and than back to the mixer to continue the final mix output.

The stereo channel(A)

MIC microphone input

This is an XLR type balanced connector for microphone,the input level range: -60~20dB. At this channel the amplified signal will be feed to the L/R main bus equally finally.

ST LINE IN Line input:

This is one unbalanced phone jacks to which line level devices can be connected, the rated input level is -10dB. The tip of JK socket is used for Left input channel, and the ring of JK socket is used for Right input channel, When you connect the socket’s tip and ring, the right signal will be same as the left.

-10dB attenuation switch Press this knob, the input signal will be a ttenuated 10dB, when the input signal level is too strong.

BAL：

This knob is used for controlling the ste reo signal of the channel feed to L/R buses as some proportion to balance the stereo so und image.

HI :

This knob control the frequency equal izer at higher frequency point. Max adjust range： 15dB @ 12KHz±

MID

This knob control the frequency equal izer at middle frequency point. Max adjust range: ±15dB @ 2.5KHz

LOW:

This knob control the frequency equal izer at lower frequency point. Max adjust range: ±15dB @ 80Hz

AUX1,AUX2,AUX3,AUX4:

These 4 set in front of the channel fader, so they are not dependent on the fader position.

knobs are used for controlling the signal level feed to AUX1~4 bus, these 4 parts are all

EFF:

CHANNEL FADER:

This fader controls the output level feed to main bus from the input channel, adjusting the volume balance between channels. Faders of channels not in use should be pulled down.

SIG,PEAK Indicador:

PFL :switch

This switch allows you to monitor the sig nal of the input channel, the signal is sampled in front of the channel fader, so it has nothing to d o with the fader position.

SUB,MAIN channel output control:

These two switches control if the chann el signal will feed to the SUB and MAIN bus or not separately. The switch should be turned off for unused channe ls.

GAIN control

Use this knob to adjust the level of the inpu t signal to the optimal level. For the best balance of S/N ratio and dynamic range, a djust this knob so that the peak indicator 12 lights occasionally.

PHANTOM +48V phantom power switch and indicator

This button switch is used for turning on or off the +48V phantom power in the unit. The +48V phantom power will exist on the input socket of each microphone input channel when this switch is pressed. Notices: Slide down all channel fader before turning on or off the switch; Don't plug or unplug microphone after this switch were turned on; Don't turn on the phantom switch when a dynamic microphone is in use.

Thi s A C power s upply s ocket h as a fuse -hold er, use th is sock et to con nect th e AC po wer out let.

POW ER SOCK ET & FUSE H OLDER :

Use d for tur n on/of f the un it.

AC PO WER SWI TCH

Rear panel

Connection cables

USB port:

This USB jack is a communication port by which the USB audio interface of the mixer can carry data with a computer . The computer in use do not need any drive soft, plug and play, also it provides power for the USB audio interface at the same time.

PR OFESS IONAL MIX ER

Serie PAMX3

PR OFESS IONAL MIX ER

Serie PAMX3

PAGE 11

EFFECT LIST

PAGE 6

-10 dB

MID

LOW

AUX1

AUX2

AUX3

AUX4

BAL

ST LINE 13/14

-15 +15

SIG

PFL

SUB

MAIN

-50

-30

-20

-15

-10

SIG

13/1 4

REV ERB HAL L

2.0 S

2.5 S

3.0 S

4.0 S

5.0 S

6.0 S

8.0 S

01 02 03 04 05 06 07 08 1 0.0 S

REV ERB ROO M

1.0 S

1.5 S

2.0 S

2.5 S

3.0 S

09 10 11 12 13 14 4.0 S

REV ERB PLATE

1.0 S

1.5 S

2.0 S

2.5 S

3.0 S

15 16 17 18 19 20 4.0 S

AMB IENT

0.5 S

0.7 S

1.0 S

1.3 S

21 22 23 24 25 1.6 S

GATED R EVERB

75 MS 100 M S 125 M S 150 M S 200 M S

26 27 28 29 30 31 300 M S

REV ERSE RE VERB

75 MS 100 M S 125 M S 150 M S 200 M S

32 33 34 35 36 37 30 0 MS

VOI CE DOUB LER

60 MS

80 MS 100 M S 120 M S

38 39 40 41 42

140 M S

ECH O & ROOM

0.1 /1.0 S

43 44

0.1 5/1.5 S

ECH O & HALL

0.2 /2.0 S

0.2 5/2.5 S

0.3 /3.0 S

0.3 5/3.5 S

0.4 /4.0 S

45 46 47 48 49 50

0.5 /5.0 S

ECH O 50% FB

100 M S 125 M S 150 M S 200 M S 250 M S 300 M S 350 M S 400 M S 500 M S 650 M S

51 52 53 54 55 56 57 58 59 60 61

800 M S

SIN GLE DEL AY

50 MS 100 M S

150 M S 200 M S 250 M S 300 M S 400 M S

62 63 64 65 66 67 68 69

500 M S

CHO RUS FAST

&EC HO 0.1 S

70 71 72

&RO OM 1 S

CHO RUS MED

&EC HO 0.2 S

73 74 75

&HA LL 2 S

CHO RUS SLO W

&EC HO 0.3 S

76 77 78

&HA LL 4 S

FLA NGER FAS T

&EC HO 0.1 S

79 80 81

&RO OM 1 S

FLA NGER ME D

&EC HO 0.2 S

82 83 84

&HA LL 2 S

FLA NGER SL OW

&EC HO 0.3 S

85 86 87

&HA LL 4 S

TRE MOLO FAS T

88 89

&RO OM 1 S

TRE MOLO ME D

90 91

&HA LL 2 S

TRE MOLO SL OW

92 93

&HA LL 4 S

WAH WAH FA ST

94 95

&RO OM 1 S

WAH WAH M ED

96 97

&HA LL 2 S

WAH WAH S LOW

98 99

&HA LL 4 S

99 preset DSP effect list

L left line input

These are two unbalanced connectors to which the left of a line level device can be connected, the rated input level is -10dB. Here it is convenient for selecting RCA connector or phone jack.

R Right line input

These are two unbalanced connectors to which the right of a line level device can be connected, the rated input level is -10dB. Here it is convenient for selecting RCA connector or phone jack.

-10dB attenuation switch Press this knob, the input signal will be a ttenuated 10dB, when the input signal level is too strong.

BAL：

This knob is used for controlling the ste reo signal of the channel feed to L/R buses as some proportion to balance the stereo so und image.

HI :

This knob control the frequency equal izer at higher frequency point. Max adjust range： 15dB @ 12KHz±

MID

This knob control the frequency equal izer at middle frequency point. Max adjust range: ±15dB @ 2.5KHz

LOW:

This knob control the frequency equal izer at lower frequency point. Max adjust range: ±15dB @ 80Hz

AUX1,AUX2,AUX3,AUX4:

These 4 set in front of the channel fader, so they are not dependent on the fader position.

knobs are used for controlling the signal level feed to AUX1~4 bus, these 4 parts are all

CHANNEL FADER:

This fader controls the output level feed to main bus from the input channel, adjusting the volume balance between channels. Faders of channels not in use should be pulled down.

SIG,PEAK Indicador:

PFL :switch

This switch allows you to monitor the sig nal of the input channel, the signal is sampled in front of the channel fader, so it has nothing to d o with the fader position.

SUB,MAIN channel output control:

These two switches control if the chann el signal will feed to the SUB and MAIN bus or not separately. The switch should be turned off for unused channe ls.

The stereo channel(B)

CONTROL PANEL

PR OFESS IONAL MIX ER

Serie PAMX3

PR OFESS IONAL MIX ER

Serie PAMX3

PAGE 7PAGE 10

REC OUT

BALANCED BALANCED

2TK IN

AUX1

L/MONO

AUX SEND

AUX RET

1 GROUND

2 HOT (+)

3 COLD ( )

SUB2 OUT PHONESSUB1 OUT

MAIN R OUT EFF SENDMAIN L OUT

MAIN OUT

AUX2

AUX3

AUX4

SET UP MEMO

CONTROL PANEL

Control panel

REC OUT:

These two RCA connectors can output low level stereo signal (left and right) for tape recorder.

MAIN OUT (L, R)

These four connectors are all main output sockets of this mixer, two XLR connectors are balanced and two phone jacks are unbalanced.

SUB OUT1,2 group output sockets

These two connectors are group output sockets of this mixer, they are unbalanced.

HEADPHONE stereo headphone socket

A set of stereo headphones can be connected to this phone j ack. Normally, the headphones can monitor the same signal as which sent to the each channel, w hen any PFL switch is pressed, the signal of the input channel after the equalizer will be monitored.

AUX1~4 SEND:

These are unbalanced phone jacks for sending auxiliary output signals. They can be linked to a monitor outside or linked to a sub power amplifier.

2TK IN:

These two RCA for the play input signal, rate input level: -10dB.connectors are unbalanced input

EFF SEND ：

This is jack to send the output signals to the external effector.

AUX RET:

These are two auxiliary input phone jacks. The rated input level is -10dB. Only connect the output of your source device to L/MOMO if the source is mono, thus the right signal is same as the left.

PR OFESS IONAL MIX ER

Serie PAMX3

PR OFESS IONAL MIX ER

Serie PAMX3

LINE LINELINE

MIC9

MIC10

GAINGAIN

-10 -10 -10 -10

dB dB dB dB

HI HI HI HI

MID MIDMID MID

LOW LOW LOW LOW

AUX1 AUX1 AUX1 AUX1

AUX2 AUX2 AUX2 AUX2

AUX3 AUX3 AUX3 AUX3

AUX4 AUX4 AUX4 AUX4

EFF EFF

BAL BAL BAL BAL

ST LINE 15/16

ST LINE 13/14

REC OUT

BALANCED BALANCED

2TK IN

AUX1

L/MONO

AUX SEND

AUX RET

+12

1KHz 2KHz 4KHz

8KHz

16KHz500Hz250Hz125Hz63Hz

MAIN L

MAIN R/PFL

SUB 1 SUB 2

1 GROUND

2 HOT (+)

3 COLD ( )

SUB2 OUT PHONESSUB1 OUT

MAIN R OUT EFF SENDMAIN L OUT

PFL

MAIN SUB AUX1/2

AUX3/4

EFF TO PHONES SELECTOR

+20

+60

+20

+60

-15 +15 -15 +15 -1 5 +15 -15 +15

-15 +15 -15 +15-15 +15 -15 +15

-15 +15 -15 +15 -1 5 +15 -15 +15

PK PK PK PK

SIG SIG SIG SIG

MAIN OUT

AUX2

AUX3

AUX4

MAIN

SUB AUX1/2

AUX3/4

EFF SEND 2TK IN AUX RETEFF LEVEL PHONES

STEREO GRAPHIC EQUALIZER

POFES SIONA L MIXER

OUTPUT LEVEL INDICATOR

MICMIC

ST ST

9/10

11/12

PFL

DSP EFFECTS PROCESSOR

MUTE

+10

-2

-4

-7

-20

-10

-30

-38

+10

-2

-4

-7

-20

-10

-30

-38

PFL PFL PFL PFL

SUB SUB SUB SUB

MAIN MAIN MAIN MAIN

10 10 10 10

-50 -50 -50 -50

-30 -30 -30 -30

-20 -20 -20 -20

-15 -15 -15 -15

-10 -10 -10 -10

11/12

-50

-30

-20

-15

-10

PK PK PK PK

SIG SIG SIG SIG

CLIP CLIP CLIP CLIP

+6 +6 +6 +6

0 0 0 0

-20 -20 -20 -20

10 10 10 10

-50 -50 -50 -50

-30 -30 -30 -30

-20 -20 -20 -20

-15 -15 -15 -15

-10 -10 -10 -10

AUX1 AUX2 AUX3 AUX4

MAIN

SUB

15/16

13/14

0 0 0 0

-50

-30

-20

-15

-10

LINE LINE LINE LINE LINE LINE LINE LINE

MIC1 MIC2 MIC3 MIC4 MIC5 MIC6 MIC7 MIC8

GAIN

GAIN GAIN GAIN GAIN GAIN GAIN GAIN

LOW

CUT

LOW

CUT

LOW

CUT

LOW

CUT

LOW

CUT

LOW

CUT

LOW

CUT

LOW

CUT

HI HI HI HI HI HI HI HI

MID MID MID MID MID MID MID MID

LOW LOW LOW LOW LOW LOW LOW LOW

AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1

AUX2 AUX2 AUX2 AUX2 AUX2 AUX2 AUX2 AUX2

AUX3 AUX3 AUX3 AUX3 AUX3 AUX3 AUX3 AUX3

AUX4 AUX4 AUX4 AUX4 AUX4 AUX4 AUX4 AUX4

EFF EFF EFF EFF EFF EFF EFF EFF

PAN PAN PAN PAN PAN PAN PAN PAN

+20

+60

+20

+60

+20

+60

+20

+60

+20

+60

+20

+60

+20

+60

+20

+60

-15 +15 -15 +15 -1 5 +15 -15 +15 -15 +15 -1 5 +15 -15 +15 -15 +15

PK PK PK PK PK PK PK PK

SIG SIG SIG SIG SIG SIG SIG SIG

+48V +48V

PHANTOM PHANTOM

PFL PFL PFL PFL PFL PFL PFL PFL

SUB SUB SUB SUB SUB SUB SUB SUB

MAIN MAIN MAIN MAIN MAIN MAIN MAIN MAIN

10 10 10 10 10 10 10 10

-50 -50 -50 -50 -50 -50 -50 -50

-30 -30 -30 -30 -30 -30 -30 -30

-20 -20 -20 -20 -20 -20 -20 -20

-15 -15 -15 -15 -15 -15 -15 -15

-10 -10 -10 -10 -10 -10 -10 -10

3 4

5 6

PK PK PK PK PK PK PK PK

SIG SIG SIG SIG SIG SIG SIG SIG

0 0 0 0 0 0 0 0

LINE LINE

MIC7 MIC8

GAIN GAIN

LOW

CUT

LOW

CUT

HI HI

MID MID

LOW LOW

AUX1 AUX1

AUX2 AUX2

AUX3 AUX3

AUX4 AUX4

EFF EFF

PAN PAN

+20

+60

+20

+60

-15 +15 -15 +15

PK PK

SIG SIG

PFL PFL

SUB SUB

MAIN MAIN

10 10

-50 -50

-30 -30

-20 -20

-15 -15

-10 -10

PK PK

SIG SIG

0 0

17/18

+12

1KHz 2KHz 4KHz

8KHz

16KHz

MAIN L

MAIN R/PFL

SUB 1 SUB 2

PFL

PHONES SELECTOR

0100100

MAIN

SUB AUX1/2

AUX3/4

2TK IN AUX RET PHONES

OUTPUT LEVEL INDICATOR

-50

-30

-20

-15

-10

MAIN

SUB

-50

-30

-20

-15

-10

+10

-2

-4

-7

-20

-10

-30

CLIP

+10

-2

-4

-7

-20

-10

-30

CLIP

PAGE 9PAGE 8

+12

500Hz250Hz125Hz63Hz

MAIN SUB AUX1/2

AUX3/4

EFF TO

EFF SEND EFF LEVEL

PFL

DSP EFFECTS PROCESSOR

MUTE

CLIP CLIP CLIP CLIP

+6 +6 +6 +6

0 0 0 0

-20 -20 -20 -20

10 10 10 10

-50 -50 -50 -50

-30 -30 -30 -30

-20 -20 -20 -20

-15 -15 -15 -15

-10 -10 -10 -10

AUX1 AUX2 AUX3 AUX4

0 0 0 0

POF ESSIO NAL MIX ER

This knob used to control the input signal level from 2TK IN sockets to main stereo bus and SUB group output.

2TK IN:

CONTROL PANEL

This double 7-segment LED display is used for indicating the work state of the inner effector, and the corresponding effect are shown as blow.

State display of inner effector:

These two buttons are used for selecting the states of the inner effector.

Buttons for choosing the state:

EFF SEND:

This knob is used for controlling the sig nal level feed to the inner effector from all input channels and a lso controlling the signal level output from the EFF SEND socke ts.

EFF LEVEL:

This knob is used for controlling volume o f the signal level from the output of the inner effector.

This button is used for muting the effect. Whe n you press and hold the button, the display will flash a nd the effect will be muted until you loose the button.

MUTE:

This switch allows you to monitor the outp ut signal of the inner effector, the signal is sampled in front of the EFF fader, so it has nothing to do with these fader positi on.

PFL :

AUX1~4 SEND:

These four faders are used for controll ing the output level from all input channel sent to the AUX1~4 SEND phone jacks respectively.

These 4 level meters indicate the signal level of the AUX1~AUX4 output

Level meter for AUX output:

EFF To EFFECT switch:

Press these 4 switch, can feed the effect signal to MAIN OUT, SUB OUT, AUX OUT1/2 and AUX OUT3/4 respectively.

Level meter for SUB1,SUB2 group output

This level meter indicates the signal l evel of the group output (SUB1 and SUB2).

PHONES SELECTOR :

When no channel PFL switch is pressed, these 4 butto ns choose whitch signal feed to headphon e monitor. When one channel PFL switch is pressed, you can hear the pressed channel signal sampled in fro nt of this channel fader.

PHONES volume control:

This knob controls the volume of the head phones connected to the headphone jack.

AUX RET :

This knob control the input level from an e xternal processor as external effector etc. conn ected to AU X RETURN. The signal will be feed to stereo main b us and sub bus.

Stereo L/R master control:

These two slide faders are used for adjusti ng the final output level sent to the stereo output so ckets.

SUB1, SUB2 group output control:

These two slide faders are used for adjusti ng the final output level sent to the group output socke ts.

Graphic equalizer and EQ ON switch:

This 9-band stereo graphic equalizer will be inserted in the main output stage, when the EQ ON button is pressed.

Level meter for output:L,R/PFL

This level meter indicates the signal l evel of the stereo main output (Left, Right and PFL). When a PFL button i s pressed, PFL LED light, the Right channel level i ndicator turned into input signal level indica tor of this channel.

PR OFESS IONAL MIX ER

Serie PAMX3

PR OFESS IONAL MIX ER

Serie PAMX3

Audiodesign PAMX3.82, PAMX3.122 Owner's Manual

Specifications and Main Features

Frequently Asked Questions

User Manual