Audio Design P1T-S User Manual
Serial Number: Date of Purchase:
Installation & Operation
Installation et fonctionnement
Instalación y funcionamiento
Einbau und Betrieb
Installazione e funzionamento
Component Systems
P152-S – 5.25˝
P1652-S – 6.5˝
P1T-S – Tweeter System
, dealer name, product purchased and date of
der to receive service, the purchaser must provide
In or
chaser of Rockford product purchased from an Authorized
etion.
d's discr
or
e
.S.A.
d Driv
or
Arizona 85281 U
,
Rockford Corporation
Rockford Fosgate
600 South Rockf
empe
T
(480) 967-3565
vice 1-800-669-9899
.S.A.,
n U
I
Customer Ser
www.rockfordfosgate.com
Printed in China
TEMENT
A
Rockford Corporation offers a limited warranty on Rockford Fosgate products on the following terms:
LIMITED WARRANTY ST
Length of Warranty
Speakers – 1 Year. Any Factory Refurbished Product – 90 days (receipt required)
What is Covered
This warranty applies only to Rockford Fosgate products sold to consumers by Authorized Rockford Fosgate
not by Rockford Corporation.
Authorized Rockford Fosgate Dealer in another country are covered only by that country’s Distributor and
Dealers in the United States of America or its possessions. Product purchased by consumers from an
Who is Covered
eceipt stating the customer name
y the original pur
y of the r
ound to be defective during the warranty period will be repaired or replaced
ers onl
v
oducts f
osgate Dealer in the United States.
Pr
oduct deemed to be equivalent) at Rockf
.
ranty co
d F
d with a cop
or
or
chase
This war
Rockf
Rockf
pur
(with a pr
1. Damage caused by accident, abuse, improper operations, water, theft, shipping
2.Any cost or expense related to the removal or reinstallation of product
3. Service performed by anyone other than Rockford or an Authorized Rockford Fosgate Service Center
What is Not Covered
vice
liability in connection with the sale of the product.
Any implied warranties including warranties of fitness for use and merchantability are limited in duration to the
period of the express warranty set forth above.Some states do not allow limitations on the length of an implied
Limit on Implied Warranties
warranty,so this limitation may not apply.No person is authorized to assume for Rockford Fosgate any other
w to Obtain Ser
Ho
4.Any product which has had the serial number defaced, altered, or removed
5. Subsequent damage to other components
6.Any product purchased outside the U.S.
7.Any product not purchased from an Authorized Rockford Fosgate Dealer
Authorization number) to return any product to Rockford Fosgate.You are responsible for shipment
Contact the Authorized Rockford Fosgate Dealer you purchased this product from.If you need further
assistance, call 1-800-669-9899 for Rockford Customer Service.You must obtain an RA# (Return
of product to Rockford.
2009 Rockford Corporation.All rights reserved.
Rockford Fosgate and the Rockford Fosgate logo are either
registered trademarks or trademarks of Rockford Corporation.
anty
arr
W
This product meets the current EU warranty requirements,see your Authorized dealer for details.
EU
01/2009 B.M.
02/2009 E.R.
1230-55479-01
SAFETY
Cutout
Hole
Pos
ition to
Align Holes
Example of standard door installation
Cutout
Hole
Position to
Align Holes
Example of standard door installat
Use tip of a small flat
screwdriver to remove tweeter
Example of Discreet Dual Clamp (DDC™)
Tw eeter Mounting (Flush Mount)
Panel
CAUTION: Before installation, disconnect the battery
negative (-) terminal to prevent damage
to the unit, fire and/or possible injury.
PRACTICE SAFE SOUND™
uous exposure to sound pressure levels over 100dB may
Contin
cause permanent hearing loss. High powered auto sound systems
may produce sound pressure levels well over 130dB. Use common
sense and practice safe sound.
CARTON CONTENTS
• (1) Set P1 Series Speakers with Tweeters or
P1T-S Tweeter System with Crossover
• (1) Set of grilles/trim rings
• Mounting Hardware and Tweeter Surface, Angle, and Flush Mounts
INSTALLATION CONSIDERATIONS
Before beginning any installation, follow these simple rules:
1. Be sure to carefully read and understand the instructions before attempting to
install these speakers.
2. For safety, disconnect the negative lead from the battery prior to beginning the
installation.
3. For easier assembly, we suggest you run all wires prior to mounting your speakers
in place.
4. Use high quality connectors for a reliable installation and to minimize signal or
power loss.
Think before you drill! Be careful not to cut or drill into gas tanks,fuel lines,
5.
brake or hydraulic lines,vacuum lines or electrical wiring when working on any
vehicle. If installation in a boat, take care not to cut or drill through the main hull.
6. Never run wires underneath the vehicle.Running the wires inside the vehicle or
hull area provides the best protection.
7. Avoid running wires over or through sharp edges.Use rubber or plastic
grommets to protect any wires routed through metal,especially the firewall.
MOUNTING
1. Determine where the speakers will be mounted. Ensure an area large enough for
the speaker to mount evenly. Be sure that the mounting location is deep enough
or the speaker to fit; if mounting in a door, operate all functions (windows, locks,
f
etc.) through their entire operating range to ensure there is no obstruction.
2. Refer to the specification chart to determine the proper diameter hole to cut
for your speaker model.The template provided also gives the proper cutout size.
3. Mark the locations for the mounting screws. Drill the holes with a 1/8" bit.
4. Feed the speaker wires through the cutout and connect to the speaker terminals.
Be sure to observe proper polarity when connecting the wires.The speaker's
positive terminal is indicated with a "+".
On models with slotted holes,
5.
screws in the slots at the top and bottom.This will allow you to rotate the speaker to match the remaining mounting holes.When aligned, tighten the screws.
ws until the speak
Tighten the scr
6.
over tighten the screws.
If needed use the adapter plate pr
NOTE:
Adapter Plate Templates at the end of this manual.
e
fit the speak
er into the cutout and install the
er is snug in place to prevent rattling.Do not
ovided to mount the speaker
. See
2
IN – Connect from Amplifier
From Amplifier
TWT – Connect to Tw e eter
1/4”
(0.25”)
3/16”
(0.1875”)
P1T-S – System Connection
0dB
-2dB
-4dB
FEATURES
SPECIFICATIONS
eet Dual Clamp (DDC™)
Discr
Tweeter Mount
Every aspect of the new Tweeter design has been
completel
ease of installation and fitment.This optimized
patent pending design provides concentric
clamping pressure around the perimeter of the
mounting hole.
The “mounting cups” are in fact not “cups” at all,
but rather unobtrusive “clamps” that quickly
and easily mount in a standard 1.75 inch (45mm)
hole saw opening with a single center screw
securing with balanced pressure to both faces
of the mounting surface. From there, the tweeter
simply snaps into place and is secured by a
snap-on trim ring. Removal is easy if needed.
The protective grille on the tweeter is
non-removable and an intergral part of the design.
ICC (Integrated Concealed Crossover)
For the P152-S and P1652-S, the crossover is
integrated into the basket of the mid-bass driver.
This component grade crossover allows for easy
connection of the full component system without
the need for an external crossover. Just connect
the wires from the tweeter to the
terminals at the speaker, see below.
y re-engineered to allow for maximum
TWT
P1 Components
Nominal Diameter - inch (mm) 5.25 (133.35) 6.5 (165.10) 1.0 (25.0)
Description 2-Way 2-Way Tweeter Kit
Nominal Impedance (ohms) 4Ω 4Ω 4Ω
Frequency Response (Hz) 70Hz-22kHz 60Hz-22kHz 3.5kHz-22kHz
Crossover Frequency (Hz) 3.5kHz 3.0kHz 3.0kHz
12dB/octave Butterworth Crossover HP (High Pass) HP (High Pass) HP (High Pass)
Voice Coil Diameter - inch (mm) 1.0 (25.4) 1.0 (25.4) –
Fs - Free Air Resonance (Hz) 70Hz 60Hz 3.5kHz
Qts 0.68 0.68 –
Vas - cu. ft. (Liter) 0.19 (5.4) 0.60 (16.8) –
Xmax - inch (mm) 0.1 (2.5) 0.14 (3.5) –
SPL (dB @ 1w/1m) 87dB 89dB 90dB
Power Handling-Watts (RMS / Peak) 50/100 60/120 60/120
Mounting Diameter-inch (mm) 4.81 (122.21) 5.57 (141.35) 1.75 (44.40) (Flush Mount)
Mounting Depth-inch (mm) 1.87 (47.50) 2.17 (55.00) 0.91 (23.14) (Flush Mount)
Includes Grille/Trim Ring YES YES YES
Trim Ring Diameter-inch (mm) 6.22 (158.00) 6.97 (177.00) 2.10 (53.34)
Trim Ring Height-inch (mm) 0.88 (22.34) 0.83 (21.00) 0.30 (7.66)
Includes Adapter Plate 5"x7"/6"x9" 5"x7"/6"x9" NO
P152-S P1652-S P1T-S
Specifications subject to change without notice.See figures on following pages.
WIRING
P1T-S Crossover Wiring
1. Use illustration for proper connection.
2. Be sure to maintain speaker polarity.
3. Connecting the positive wire to 0dB matches the amplitude of the tweeter to the speaker.
4. Connecting the positive wire to -2dB or -4dB reduces the amplitude of the tweeter -2dB
or -4dB lower than the midrange, (ideal for tweeters located high in door panels and
midranges located lo
w in the kick panel).
Crossover
Tweeter
3
5.43"
(138.00mm)
Diameter
6.02"
(153.00mm)
6.22"
(158.00mm)
3.84"
(97.58mm)
2.29"
(58.23mm)
0.88"
(22.34mm)
0.83"
(21.00mm)
1.87"
(47.50mm)
4.81"
(122.21mm)
P152-S P1652-S
6.18"
(157.00mm)
Diameter
6.77"
(172.00mm)
4.37"
(111.02mm)
2.63"
(66.70mm)
2.17"
(55.00mm)
5.57"
(141.35mm)
6.97"
(177.00mm)
5.43"
(138.00mm)
Diameter
6.02"
(153.00mm)
6.22"
(158.00mm)
3.84"
(97.58mm)
2.29"
(58.23mm)
0.88"
(22.34mm)
0.83"
(21.00mm)
1.87"
(47.50mm)
4.81"
(122.21mm)
P152-S P1652-S
6.18"
(157.00mm)
Diameter
6.77"
(172.00mm)
4.37"
(111.02mm)
2.63"
(66.70mm)
2.17"
(55.00mm)
5.57"
(141.35mm)
6.97"
(177.00mm)
2.13"
(54.00mm)
2.13"
(54.00mm)
1.75"
(44.40mm)
Mounting Hole
Diameter
Mounting
Depth
2.10"
(53.34mm)
1.06"
(27.00mm)
0.30"
(7.66mm)
0.50"
(12.70mm)
0.32"
(9.20mm)
0.91"
(23.14mm)
Tweeter
Surface Mount
Flush Mount
1.9"
(48.27mm)
1.22"
(30.87mm)
1.59"
(40.50mm)
3.39"
(86.00mm)
2.85"
(72.50mm)
P1T-S – Tweeter Kit Crossover
SPECIFICATIONS
Specifications subject to change without notice.
4
Loading...