TH113-RRegulator
Introduction Control Module Installation
Operation
User Guide
Thank you for choosing Aube’s TH113-R Regulator.
The TH113-R is specially designed to control a floor
heating installation, a baseboard or a convector.
The TH113-R regulator operates like a dimmer switch to
GFCI Test
and Warning
Light
allow you to easily adjust the amount of power sent to
your heating system.
It features an integrated GFCI, and includes a test button
and warning light for added security.
This regulator is also equipped with an ON/STANDBY
On/StandBy
Switch
switch making it possible to put it in sleep mode when its
use is not required (e.g. summer).
IMPORTANT!
The GFCI and Remote Input options are not available
with a low voltage power base. Skip sections 3 and 4.
Power
Selection
Dial
GFCI Test (GA/GB line power base only) Remote Input (line voltage only)
The GFCI monitors the electrical flow for any loss of
current; if there is any loss, the thermostat will cut off
power to the heating system.
We recommend you test the GFCI immediately after
installing the control module, and once a month thereafter
to ensure it is operating properly.
To test:
n Press the TEST button:
• Successful: TEST warning
light is ON and power to
heating system is cut off.
• Unsuccessful: TEST warning
light is OFF.
Cut power to heating system from the main power
panel and call customer service.
o When successful, reset thermostat (STANDBY/ON)
to power heating system.
NOTE: If the test warning light comes ON during normal
operation, cut power to heating system from the main
power panel and have an electrician verify the installation.
When a remote control interface (Aube CT241 or any
other remote control system) is connected to the power
base’s remote input and a signal is received, the TH113-R
module automatically lowers the percentage by 35%
based on the dial’s current position.
The LED lights up to indicate the signal’s presence
(except for GA and GB models).
ࠆࠜࠚࠡ ࠔࠟߓ ࠧ࠘ࠠࠣࠢࠥࠔࠥࠬߓࠕࠬࠣࠔࠦࠦ
The TEST button can be used to bypass the signal for a
2-hour period.
The LED goes off to indicate the bypass.
NOTE: When combined with a GA or GB power base, the
TEST button is used only for GFCI testing. The
percentage is decreased, but the bypass function and
indicator are not available.
Align the bracket tabs on the regulator with the holes
located on the power base.
Control Module
Power Base
This regulator must be installed on a PB112 power
base.
The screw cannot be removed completely.
Keep the regulator’s air vents clean and free from
obstructions.
Technical Specifications
Model: TH113-R
Power setting range: 0 to 100%
Storage: -20°C to 50°C (-4°F to 120°F)
Warranty
AUBE TECHNOLOGIES INC. ONE (1) YEAR LIMITED
WARRANTY
This product is guaranteed against workmanship defects for a one
year period following the initial date of purchase. During this period,
AUBE Technologies Inc. will repair or replace, at our option and
without charge, any defective product which has been used under
normal conditions.
The warranty does not cover delivery costs and does not apply to
products poorly installed or randomly damaged following installation.
This warranty cancels and replaces any other manufacturer's
express or implied warranty as well as any other company
commitment.
AUBE Technologies Inc. cannot be held liable for related or random
damages following the installation of this product. The defective
product as well as the purchase invoice must be returned to the
place of purchase or mailed, prepaid and insured, to the following
address:
Aube Technologies Inc.
705 Montrichard
Saint-Jean-sur-Richelieu, Quebec, Canada J2X 5K8
The TH113-R regulator operates on perpetual 15-minute
heating cycles.
For example, if the dial is set
halfway, the system will heat
for 50% of the cycle; it will be
ON for 7.5 minutes and OFF
for 7.5 minutes.
Below is a detailed table of the
cycle duration based on the
dial’s position:
Position and
equivalent %I 0%220%440%660%880%10100%
ON 0 min 3 min 6 min 9 min 12 min 15 min
OFF 15 min 12 min 9 min 6 min 3 min 0 min
NOTE: Depending on the power base used, the heating
cycles can be 15 seconds or 15 minutes.
If you have any questions concerning the TH113-R
Regulator, call our technical support team at:
Phone: Montreal area: (450) 358-4600
Canada / U.S.: 1-800-831-AUBE (2823)
Fax: (450) 358-4650
Email: service@aubetech.com
Monday to Friday from 8:30 AM to 5:00 PM EST.
For more information on our products, visit us at:
www.aubetech.com
05/11/03 400-113-004-A
PB112-024T-15S
Installation Instructions
24 V Low-Voltage Power Base
n
The PB112-024T-15S power base can b e used on any TH11x series
thermostat (with the exception of the TH110 model). This low-voltage
power base operates on 15-second cycles and can be connected to
a line-voltage load using a solid-state relay. The PB112-024T-15S is
compatible with most solid-state relays; however, the following Aube
relays are optimized for use with this power base:
• RT850 solid-state relay (SSR)
• RT850T solid-state relay (SSR) with built-in 24-V transformer
Applications
WARNING
This power base MUST be used ONLY with solid-state relays. The
use of electromechanical relays will result in reduced life expectancy and in the possibility of overheating of these devices.
o
Supplied Parts
n One (1) power base
o Two (2) plastic anchors
p Two (2) mounting screws
p
For a new installation, choose a location about 1.5 m (5 ft.)
The thermostat must be installed on an inside wall facing the
Avoid locations where there are air drafts (top of staircase, air
q
The installation must be carried out by an electrician and comply with local electrical codes.
Installation Guidelines
above the floor.
heating system (except for floor heating systems).
outlet), dead air spots (behind a door), direct sunlight or
concealed chimney or stove pipes (except for floor heating
systems).
Installation Procedure
n Turn off power to the heating system at the main electrical panel
to avoid electrical shock.
o Wire the base according to your application. See typical wirin g
diagrams in sections 4.1 and 4.2.
1.
s Install the control module onto the base.
t Apply power to the heating system.
u Verify the installation by checking that the heating system can be
turned on or off using the thermostat.
4.1 Single SSR with Built-in Transformer
Electrical
Panel
2.
4.2 Multiple SSRs with External Transformer
Electrical
Panel
3.
Heater
Heater
r
4.
Maximum load: 0.5 A / 24 VAC
Heating cycle length: 15 seconds
Operating temperature: 32°F to 122°F (0°C to 50°C)
Storage: -4°F to 122°F (-20°C to 50°C)
Size (H•W•D): 124 x 70 x 23 mm (4.89 x 2.76 x 0.91 in)
Wire gauge: 14 to 22 AWG
Technical Specifications
Blue
Black
Red
Black
Red
Black
Red
Heater
External 24 V
Transformer
5.
p For a floor heating system installation, con-
nect the floor sensor between the S and R terminals.
q Secure the base to the wall using the provided screws and wall
anchors.
r Configure the switches located on the control module (if any).
Refer to the user guide.
PB112-024T-15S 400-112-024-A 18/1/06 1/1