Aube Technologies CT241 Installation Instructions And User Manual

The CT241 telephone controller is designed to remotely control up to
four independent loads.

For example, you could connect a sprinkler system, a water heater,
etc. Another example would be to connect an output to the thermo­stat’s phone interface (which requires a dry contact) to switch from
Comfort mode to V acation mode and vice versa.

Loads can be activated or deactivated remotely (by telephone) or
manually (on-site).

)LJXUH 

ЛнкЯрЮпϫКсансдат

Any device connected to a telephone line must conform to the coun­try's standards. The CT241 telephone controller meets:

• FCC68 standards for installation on the North American network.

• FDTBR21 standards for installation on the European network.

2.1 Included Parts

• One CT241 telephone controller)

• One power transformer 120 V (North America) or 250 V (Europe)

• One 5 m (16 foot) telephone cable

2.2 Installation Procedure

NOTE: If you are usi ng an ans wering m achine, positi on the a nswer-

ing machine switch to ON befo re insta lling th e CT241. M ake sure that
your answering machine answers after a minimum of 4 rings.

)LJXUH

ЌйотандйвϫИЬЮгдйаϫ ОтдпЮг

)LJXUH

ПфлдЮЬзϫДйопЬззЬпдкй

n Mount the CT241 near a telephone outlet.

NOTE: If you plan to connect a load having more that 30 volts on the

auxiliary outputs, the CT241 must be installed inside a certified elec­trical box.

o OPTIONAL. Connect your phone (or answering machine) to the

PHONE connector of the CT241.

p Connect one end of t he telephone ca ble to the LINE co nnector of

the CT241 and the other end to the telephone outlet in your
home.

q Connect the loads.

The four outputs of the CT241 allow you, for example, t o activate
or deactivate the light ing s ys tem , the s prin kl er sy ste m, th e w a ter
heater, etc.
You can also connect a thermostat’s telephone interface (which
requires a dry contact) to automatically switch from Comfort
mode to Vacation mode and vice versa.

NOTE: The cap acity per output is 10 A @ 240 VAC. However, to

avoid electrical shocks, the direct connection of a load exceeding
30 VAC is not permitted unless the CT241 is installed inside a certi­fied electrical box.

r When all connections have been made, connect the power

transformer to the 9 V outlet of the CT241 and the other end to
the wall electrical outlet.
The power indicator light is ON when the circuit is powered.

1 . Introduction

1 Power Indicator. Indicates the CT241 is pow ered on. T o turn

it off, unplug the power transformer.

2 Communication Indicator. Indicates the CT241 has

answered and is awaiting a command.

3 Ring Indicator. This indicator flashes when the phone rings.
4 Reset. This button can be used to reset the CT241 to its

default values. Seesection 3.2.

5 Manual Output Activation Button. C an be used to manually

activate or deactivate a relay.

6 Terminal Board. See section 2.

2. Installation

CT241 Telephone

Controller

Installation Instructions and User Manual

400-241-001-A

NOTE: The CT241 will automatically hang up if no key is pressed

during the 30 seconds following the CT241 answering a call.

Default values: access code (1234), number of rings (4)

BEGIN A SESSION (without answering machine)

BEGIN A SESSION (with an answering machine)

ENTERYOURACCESSCODE

OUTPUT S TATUS/MOD IFY STATU S

MODIFY THE ACCESS CODE

MODIFY THE NUMBER OF RINGS

SKRQHRQO\

END SESSION

3.1 Manual Output Activation Buttons

You can switch a relay status by pressing the corresponding input’s
button directly on the CT241.

This function is not accessible while the CT241 is answering a tele­phone call.

3.2 Reset Operation

Insert a pointed object (e.g. paper clip) in the hole located under the
Reset light. The light will flash 3 times to indicate that the CT241 has
been reset:

• number of rings: 4

• access code: 1234

• relays’ status: open

Power supply: 9 VAC / 60Hz (50 Hz Europe)
Outputs: Four SPST with the following capacity:

• 5 A / 30 VAC inductive / Power Factor: 0.4

• 10 A / 30 VAC resistive (if installed in a certified electrical box)

• 10 A / 240 VAC resistive (if installed in a certified electrical box)

• 1/2 HP / 120 VAC motor (if installed in a certified electrical box)

• 1 HP / 240 VAC motor (if installed in a certified electrical box)

Protection: Class II
Access code (default): 1234
Number of rings (default):4 rings
Memory protection: In case of power failure, access code and out-

put status are protected.

Phone certification standard:

• FDTBR21: European telephone network

• FCC68: North American telephone network

Approvals:

• c UL us (North America)

• CE (Europe)

Dimensions (H W D): 2.7 x 5.4 x 1.2 in. (69 x 137 x 31 mm)

AUBE TECHNOLOGIES INC. THREE (3) YEAR LIMITED WARRANTY

This product is guaranteed against workmanship defects for a three­year period following the initial date of purchase. During this period,
AUBE Technologies Inc. will repair or replace, at our option and with­out charge, any defective prod uc t w hi ch has be en u se d u nde r normal
conditions.

The warranty does not cover delivery costs and does not apply to
products poorly installed or randomly damaged following installation.

This warranty cancels and replaces any other manufacturer's
express or implied warranty as well as any other company commit­ment. AUBE Technologies Inc. cannot be held liable for related or
random damages following the installation of this product.

The defective product as well as the purchase invoice must be
returned to the place of purchase or mailed, prepaid and insured, to
the nearest shipping address.

3. Operation

Dial your phone number
Wait for the number of rings...
CT241 answers

Dial your phone number
Let it ring once and hang up
Wait 10 seconds ...
Dial your phone number again within the next 30 seconds

CT241 answers (1

st

ring)

Enter your 4-digit access code
(default: 1234)

Accepted

Error

Press the output’s corresponding
number for status

Deactivated

(open)

Press to change its status

Activated

(closed)

Press

Enter your new 4-digit access code

Enter the access code again

Accepted

Error

Press
Enter the number of rings after

which the CT241 will answer
(between 1 and 9)

x the number of

selected rings

Press to end the session

4. Technical Specifications

5. Warranty

705 Montrichard
Saint-Jean-sur-Richelieu
Quebec, Canada J2X 5K8

Tel.: [phone]
Toll Free: 1-800-831-AUB E
Fax: [phone]

[e-mail]

10 Ampère Street
95500 Gonesse
France
33 (0) 1 34 07 99 00

33 (0) 1 34 07 99 19
[e-mail]

For more information on our products, visit us

at: www.aubetech.com

29/10/2003 400-241-001-A