ATV VDM700DN User Manual
M110-VD61-002
VDM700DN
Mini Vandalproof Dome Camera
OPERATION MANUAL
Thank you for choosing our high quality camera.
Before attempting to connect or operate, please read and follow these instructions.
KEY FEATURES
These cameras are equipped with 1/3" Sony Exview HAD CCDⅡ, Solid-State Imaging
Device which provides superior performance.
Its very low current consumption of 110mA or Less and excellent durability
(Vandal proof, IP66) allow easy installation in any location.
ACCESSORIES FURNISHED
Accessories DIY cable Mount screw Set Screw
Q'ty - 4 3 1 1 1
Option 1 - - - - -
Instruction
Manual
L wrench Mount Guide
SPECIFICATIONS
Signal Format NTSC PAL
Image Device 1/3" Sony Exview HAD CCD
Scanning
System
H.Resolution 700TV Lines
Scanning
Frequency
Total Pixels 1020(H) x 508(V) 1020(H) x 596(V)
Effective Pixels 976(H) x 494(H) 976(H) x 582(V)
Electronic
Shutter Speed
S/N Ratio More than 50dB(AGC Off)
Gamma r =0.45
Min.Illumination 0.05Lux / F2.0
Sync System Internal
Video Output 1.0 Vp-p Composite 75(Ω)
Input Power
Source
Lens Fitted Board Lens
Operating
Temperature
Storage
Temperature
Dimensions Ø 81 x 63 mm
IP rating IP66
Specications and designs are subject to change for improving the functionality of this product without notice.
H:15.734KHz, V:59.94Hz H:15.625KHz, V:50Hz
1/60 - 1/100,000 sec
Automatic
2 : 1 Interlace
DC 12V ±10%, Less than 110mA
-10℃ ~ +50
-20℃ ~ +60
Ⅱ
℃
℃
1/50 - 1/100,000 sec
Automatic
DIMENSIONS
Unit : mm
59.5
ø
30.3
ø
63.6
82.2
CAMERA MOUNTING POSITION
51
360° PAN
4-ø6.8
4-ø4 HOLE
51
Indication of screen top
OPEN
CLOSE
Turn the lock counterclockwise pushing it up to
loosen it for ball part adjustment (step 1) and
loosen once more to dispart them completely
(step 2)
SCREW M2.5 x 3(3ea)
(Fixing Set)
After installing the Camera, Housing
Please tighten the screw to secure.
(Packaged using L- Wrench)
CONNECTION
DC12V REGULATED POWER
VIDEO IN
BNC FEMALE
When you install the camera, please glue up the end of cable to
keep it stable in order to protect the camera from the humidity problems.
STANDARD DC12V BNC CONNECTION
FLAT WALL
TAPPING SCREW 3 X 20(4ea)
(Wall Mounting)
TV MONITOR
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions;
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may
cause undesired operation.
Note
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the interference at his own expense.”
WARNING
This is a class A product. In a domestic environment this product may cause radio interference in which case the
user may be required to take adequate measures.
Caution
Any changes or modifications in construction of this device which are not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
1. A regulated DC12V 300mA power supply is recommended for use with this camera
for the best picture and the most stable operation.
An unregulated power supply can cause damage to the camera.
When unregulated power supply is applied, product warranty will be
out of subject.
2. It is recommended that the camera is used with a monitor that has a CCTV quality
75 video impedance level.
If your monitor is switched to high impedance then please adjust accordingly.
3. Do not attempt to disassemble the camera to gain access to the internal components.
Refer servicing to your dealer.
4. Never face the camera towards the sun or any bright or reflective light, which may
cause smear on the picture and possible damage to the CCD.
5. Do not remove the serial sticker for the warranty service.
Loading...