ATV FD700WDR User Manual

FCC COMPLIANCE STATEMENT

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

FCC INFORMATION : This equipment has been tested and found to comply with the limits for a

Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instruction manual, may cause harmful interference to

radio communications. Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference at his own expense.

CAUTION : Changes or modifications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

CE COMPLIANCE STATEMENT

WARNING: This is a Class A product. In a domestic environment this product may cause radio

interference in which case the user may be required to take adequate measures.

2

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

6. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus

(including amplifiers) that produce heat.

7. Only use attachments/accessories specified by the manufacturer.

8. Use only with the cart, stand, tripod, bracket, or table specified by the

manufacturer, or sold with the apparatus. When a cart is used, use caution

when moving the cart/apparatus combination to avoid injury from tip-over.

9. CAUTION – THESE SERVICING INSTRUCTIONS ARE FOR USE BY QUALIFIED SERVICE

PERSONNEL ONLY. TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT PERFORM ANY

SERVICING OTHER THAN THAT CONTAINED IN THE OPERATING INSTRUCTIONS UNLESS YOU

ARE QUALIFIED TO DO SO.

10. Use satisfy clause 2.5 of IEC60950-1/UL60950-1 or Certified/Listed Class 2 power sources only.

11. Indoor use only

EXPLANATION OF GRAPHICAL SYMBOLS

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert
the user to the presence of uninsulated "dangerous voltage" within the product’s enclosure
that may be of sufficient magnitude to constitute a risk of electric shock.

The exclamation point within an equilateral triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the literature
accompanying the appliance.

3

1/3” 960H Super HAD CCD II

●

● 700TVL Super High Resolution

● Day & Night function

● WDR (Wide Dynamic Range)

● High sensitivity 0.1Lux(Color), 0.00005Lux(BW, Sens-up)

● 3D Noise Reduction

● Sens-up(~x512)

● BLC, HSBLC

● Motion Detection

● Privacy Masking

● Defog

● Multi Language Support (15 languages)

● 2.8-12mm Auto Iris Vari–focal Lens

● OSD Control (Joystick)

● 3-Axis (Pan/Tilt/Rotate) Bracket

4

5

6

OSD MENU STRUCTURE

SETUP MENU

EXPOSURE
WHITE BALANCE
MOTION DET
3D-DNR
PRIVACY MASK
SPECIAL
SYSTEM

EXPOSURE

ALC

ELC

EXIT

WHITE BALANCE

ATW
AUTO
AWC-> SET KEY

MANUAL

DAY NIGHT

AUTO
SMART IR

MOTION DET

OFF

ON

DAY

NIGHT

3D-DNR

OFF

ON

PRIVACY MASK

OFF

ON

7

SPECIAL

D.ZOOM
D.EFFECT
SHARPNESS
COLOR
DEFOG
SYNC
USER TITLE
LANGUAGE

LANGUAGE

ENGLISH, CHINESE
KOREAN, JAPANESE
FRENCH, ITALIAN
SPANISH, HEBREW
PORTUGUESE,
DUTCH, GERMAN,
POLISH, RUSSIAN,

TURKISH, ARABIC

SYSTEM

FACTORY RESET
EXIT

8

EXPOSURE

ALC/ELC

BACKLIGHT - Adjusts to view the object clearly in backlight conditions.

BLC : The backlight compensation feature helps alleviate issues of visibility

in high contrast areas. Set the BLC limit.

HSBLC : Use for masking brightness of the specific area to view the subject

more clearly. The HSBLC mode is automatically activated only in low
luminance scent

- AREA setting selects an area.

- GRAY SCALE selects a gray scale

- USER SCALE selects a bright level (5 levels)

- MASK: if setting MASK ON, the mask function is activate only when
HSBLC is automatically activated in low luminance scene.

WDR : sets Wide Dynamic Range.

BRIGHTNESS - Adjust the brightness.

If setting the brightness to lower value, the images is darkened. If setting the
brightness to higher value, the image gets bright.
Lower value(dark image) --- Higher value(bright image)

AGC - Set AGC: OFF / LOW / MIDDLE / HIGH

If the images are too dark, change the maximum AGC value to make the
images brighter.

SHUTTER - Select Shutter Speed : AUTO / OFF / A.FLK / 1/160 ~ 1/120,000
SENS-UP - OFF / AUTO(x4) / MANUAL (x2 ~ x10 ~ x512)

WHITE BALANCE

ATW (Auto Tracing White Balance)

Level : -10 ~ 0 ~ 10

AUTO

Level : -10 ~ 0 ~ 10

AWC -> SET KEY : It is able to set up the white balance automatically
MANUAL: Set the white balance options manually.

Red: Obtains optimum amount of Red gain.
Blue: Obtains optimum amount of Blue gain.

to where the object is seen as desired.

9

DAY / NIGHT

AUTO : Set to change the Day / Night mode automatically.

NOTE: If you set the AGC to OFF, the AUTO mode of this function is not

available and [--] mark is displayed

Burst - OFF / ON

Allows the color burst signal in monochrome mode to be removed.
Level - LOW / MIDDLE / HIGH
Dwell Time - 3 ~ 5 ~ 60 sec.

SMART IR: Set [ON) to avoid anti-saturation of IR LEDs

DAY : Color only
NIGHT : Monochrome only

Sets the hysteresis time before switching between color/mono &
mono/color to reduce the “hunting effect”

Burst - OFF / ON
Level - -10 ~ 0 ~ 10
Position & size - Adjusts the position & the size of SMART IR.

Burst - allows the color burst signal in monochrome to be removed.

OFF / ON

NOTE ; Select the BURST-ON or OFF when the color noise occurs on the

screen in NIGHT mode.

MOTION DETECTION

It detects the moving objects in the scent by monitoring changes in brightness
level. You can select the level of sensitivity for motion detection to 8 zones.

AREA SETUP

Sets AREA SELECTION ( 1 ~ 8 AREAS)
Sets STAGE - ON / OFF
Sets POSITION - Moves horizontal position of the mask

Moves Vertical position of the mask
Enlarges or decreases the horizontal size of the mark

SENSITIVITY : 0 ~ 50 ~ 100

Enlarges or decreases the vertical size of the mark.

0 - low sensitivity
100 - high sensitivity

DISPLAY - OFF / OUTLINE / MASK 1 / MASK 2
ALARM OUT - OFF / MESSAGE

10

3D-DNR

It is used to remove Digital Noise from the image in low light conditions,
when AGC is applied.

LEVEL : 0 ~ 50 ~ 100

PRIVACY MASK

It is used to block out from view part of the field of view from being seen/recorded.

Select part the screen to be not displayed.
Up to 14 zones can be registered.

RECTANGLE - MASK SELECTION : 1 ~ 8

CIRCLE - MASK SELECTION : 1 ~ 4

DISPLAY : OFF / ON
POSITION : Moves horizontal position of the mask. (10~ 90)

SIZE : Enlarges or decreases the horizontal size of the mask. (4 ~ 20)
RADIUS : Enables to adjust the RADIUS size. (1 ~ 100)

DISPLAY : OFF / ON
POSITION : Moves horizontal position of the mask

Moves Vertical position of the mask
Enlarges ordecreases the horizontal size of the mask

Moves Vertical position of the mask. (10 ~ 90)

Enlarges or decreases the vertical size of the mask. (4 ~ 20)

POLYGON - MASK SELECTION: 1 ~ 2

DISPLAY : OFF / ON
SHAPE : draws the polygon on this menu.
POSITION : Moves horizontal position of the mask. (10~ 90)

Moves Vertical position of the mask. (10 ~ 90)

SIZE: Enlarges or decreases the horizontal size of the mask. (4 ~ 20)

Enlarges or decreases the vertical size of the mask. (4 ~ 20)

NOTE: you can adjust eh mask color manually except for color 8.

RED, GREEN, BLUE and TRANSPARENCY adjustments are applied

in common from COLOR 1 to COLOR 7, after mask setting

11

SPECIAL

D-ZOOM - ZOOM enlarges the screen ( x1.0 ~ x16.0)

D-EFFECT- V-FLIP : Flips the picture vertically

SHARPNESS - sets the screen sharpness (0 ~ 50 ~ 100)
COLOR - switches the displayed picture to gray scale or color.

DEFOG - Images in extraordinary environment such as for or rain or in a very

SYNC - INT

PAN moves the screen to left of right ( -100 ~ 0 ~ 100)
TILT moves the screen to up or down (-100 ~ 0 ~ 100)

MIRROR : Turns on the mirror effect
ROTATE : Rotates the picture (180 degrees)

ON: displays the picture with color (0 ~ 50 ~ 100)
OFF: displays the picture with gray scale (0 ~ 50 ~ 100)

strong luminous intensity have DR(Dynamic Range), lower than
ordinary images. It has a contrast based defog function, which
is used to overcome such shortcoming.
ON - LEVEL (0 ~ 10)

This model supports only INT(internal) in SYNC.

12

USUER TITLE - You can use the camera identification to assign a number and

character to the camera. It is displayed on the upper left of the

screen. To remove the user title, Select OFF.

7

USER TITLE
A B C D E F G H I J K L M
N O P Q R S T U V W X Y Z
a b c d e f g h i j k l m
n o p q r s t u v w x y z

- 0 1 2 3 4 5 6 7 8 9

< > CLR POS END

CLR: Clear all entered characters and numbers.
POS: Move the USER TITLE position on the screen using the

arrow buttons.

END: Confirm your selection or exit the setting

: Moves cursor to left or right.

LANGUAGE - Select the viewer language for the camera setup menu and OSD

(BLANK): inserts a space at the cursor position.

information display
ENGLISH CHINESE KOREAN

JAPANESE FRENCH ITALIAN
SPANISH PORTUGUESE DUTCH
GERMANY POLISH RUSSIAN
TURKISH ARABIC HEBREW

SYSTEM

FACTORY RESET - Returns to the camera to the factory default settings.

DEFECT PIXEL - It can compensate the defected pixel (which may occur while using.)

Press the key to close the lens cap.

13

SPECIFICATION

MODEL NTSC PAL

POWER

VIDEO

FUNCTION

CONNECTOR

&

ETC

Power Source DC 12V±10% / AC24V±10%
Power Consumption 3.5W(300mA)
Image Sensor 1/3" 960H Super HAD II
Total Pixels 1020(H)x508(V) 1020(H)x596(V)
Effective pixels 976(H)x494(V) 976(H)x582(V)
Scanning System 2:1 interlace
Scanning Frequency 15.734KHz(H) x 59.94Hz(V) 15.625KHz(H) x 50Hz(V)
Sync. System Internal
Electronic Shutter 1/60~ 1/120,000sec
Resolution 700TVL

Min. illumination
Video Output 1.0 Vp-p (75 ohm, composite)

S/N Ratio 50dB(AGC off)
Camera Control OSD(Joystick Switch)
Image Enhancement WDR (Wide Dynamic Range)

BLC(Backlight

Compensation)

Day & Night Day&Night (ICR Filter)
MD (Motion Detection)
PM (Privacy Masking) Retangle:8 Areas, Circle: 4 Areas, Polygon: 2 Areas

WB (White Balance) ATW(1700K11.000K) / AUTO /One PUSH / MANUAL
AGC (Auto Gain Control) OFF / LOW / MIDDLE / HIGH
Exposure ELC /ALC
Brightness 0 ~ 100 steps
Sharpness 0 ~ 100 steps
Sens-up OFF, AUTO(x4), MANUAL(x2 ~ x512)

DNR(Dynamic Noise

Reduction)

Digital Image Effect Digital Zoom( ~x16), Defog, Mirror, V-flip, Rotate
Camera ID 0 ~ 255
Title A ~ Z / 0 ~ 9

English, Chinese, Korean, Japanese, French, Italian, Spanish,

OSD Language

Power Input 2-Pin Wire / Terminal Block / DC Jack
Video Output BNC connector / Spot Out
LENS 2.8~12mm F1.2~360 Vari Focal Lens

Operating Temperature
Operating Humidity 0 ~ 96% (non-condensing)
External Dimension 120(Ø) x 88(H) mm

Weight 285g

Portuguese, Dutch, German, Polish, Russian, Turkish, Arabic,
Hebrew

Color : 0.1 Lux, B/W : 0.05 Lux

B/W : 0.00005(Sens-up x512)@ F1.2 50IRE

OFF, BLC, HSBLC, WDR

Motion Detection ( 8 areas )

Adjustable Size & Sensitivity

3D DNR (100 Steps)

-10℃ ~ +50℃(14°F ~ 122°F)

14

EXTERNAL DIMENSION

15

50303762A