ATV DR-6232H Operation Manual

Download

Page 1

Hybrid Network Video Recorder

Operation Manual

Page 2

Before reading this manual

This operation manual contains basic instructions on installing and using Hybrid Network Video Recorder. Users who are using this product for the rst time, as well as users with experience using comparable products, must

read this operation manual carefully before use and heed to the warnings and precautions contained herein while using the product. Safety warnings and precautions contained in this operation manual are intended to promote proper use of the product and thereby prevent accidents and property damage and must be followed at all times.

Once you have read this operation manual, keep it at an easily accessible location for future reference.

• The manufacturer will not be held responsible for any product damage resulting from the use of unauthorized parts and accessories or from the user's failure to comply with the instructions contained in this operation manual.

• It is recommended that rst-time users of Network Video Recorder and individuals who are not familiar with its use seek technical assistance from their retailer regarding product installation and use.

• If you need to disassemble the product for functionality expansion or repair purposes, you must contact your retailer and seek professional assistance.

• Both retailers and users should be aware that this product has been certied as being electromagnetically compatible for commercial use. If you have sold or purchased this product unintentionally, please replace with a consumer version.

Safety Precautions

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning ash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product’s enclosure that may be of sucient magnitude to constitute a risk of electric shock.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

Symbol Publication Description

IEC60417, No.5032 Alternating current

Page 3

Before reading this manual

1. Read Instructions

All the safety and operating instructions should be read before the appliance is operated.

2. Retain Instructions

The safety and operating instructions should be retained for future reference.

3. Cleaning

Unplug this equipment from the wall outlet before cleaning it. Do not use liquid aerosol cleaners. Use a damp soft cloth for cleaning.

4. Attachments

Never add any attachments and/or equipment without the approval of the manufacturer as such additions may result in the risk of re, electric shock or other personal injury.

5. Water and/or Moisture

Do not use this equipment near water or in contact with water.

6. Ventilation

Place this equipment only in an upright position. This equipment has an open-frame Switching Mode Power Supply (SMPS), which can cause a re or electric shock if anything is inserted through the ventilation holes on the side of the equipment.

7. Accessories

Do not place this equipment on an unstable cart, stand or table. The equipment may fall, causing serious injury to a child or adult, and serious damage to the equipment. Wall or shelf mounting should follow the manufacturer's instructions, and should use a mounting kit approved by the manufacturer.

This equipment and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the equipment and cart combination to overturn.

8. Power Sources

This equipment should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power, please consult your equipment dealer or local power company. You may want to install a UPS (Uninterruptible Power Supply) system for safe operation in order to prevent damage caused by an unexpected power stoppage. Any questions concerning UPS, consult your UPS retailer. This equipment should be remain readily operable.

9. Power Cords

Operator or installer must remove power and TNT connections before handling the equipment.

10. Lightning

For added protection for this equipment during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the equipment due to lightning and power-line surges.

11. Overloading

Do not overload wall outlets and extension cords as this can result in the risk of re or electric shock.

12. Objects and Liquids

Never push objects of any kind through openings of this equipment as they may touch dangerous voltage points or short out parts that could result in a re or electric shock. Never spill liquid of any kind on the equipment.

13. Servicing

Do not attempt to service this equipment yourself. Refer all servicing to qualied service personnel.

14. Damage requiring Service

Unplug this equipment from the wall outlet and refer servicing to qualied service personnel under the following conditions:

A. When the power-supply cord or the plug has been damaged. B. If liquid is spilled, or objects have fallen into the equipment. C. If the equipment has been exposed to rain or water. D. If the equipment does not operate normally by following the operating

instructions, adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualied technician to

restore the equipment to its normal operation. E. If the equipment has been dropped, or the cabinet damaged. F. When the equipment exhibits a distinct change in performance ─ this

indicates a need for service.

15. Replacement Parts

When replacement parts are required, be sure the service technician has used replacement parts specied by the manufacturer or that have the same characteristics as the original part. Unauthorized substitutions may result in re, electric shock or other hazards.

16. Safety Check

Upon completion of any service or repairs to this equipment, ask the service technician to perform safety checks to determine that the equipment is in proper operating condition.

17. Field Installation

This installation should be made by a qualied service person and should conform to all local codes.

18. Correct Batteries

Warning: Risk of explosion if battery is replaced by an incorrect type. This equipment should be remain readily operable. Dispose of used batteries

according to the instructions. The battery shall not be exposed to excessive heat such as sunshine, re or the like.

19. Tmra

A manufacturer’s maximum recommended ambient temperature (Tmra) for the equipment must be specied so that the customer and installer may determine a suitable maximum operating environment for the equipment.

20. Elevated Operating Ambient Temperature

If installed in a closed or multi-unit rack assembly, the operating ambient temperature of the rack environment may be greater than room ambient. Therefore, consideration should be given to installing the equipment in an environment compatible with the manufacturer’s maximum rated ambient temperature (Tmra).

21. Reduced Air Flow

Installation of the equipment in the rack should be such that the amount of airow required for safe operation of the equipment is not compromised.

22. Mechani cal Loading

Mounting of the equipment in the rack should be such that a hazardous condition is not caused by uneven mechanical loading.

23. Circuit Overloading

Consideration should be given to connection of the equipment to supply circuit and the eect that overloading of circuits might have on over current protection and supply wiring. Appropriate consideration of equipment nameplate ratings should be used when addressing this concern.

24. Reliable Grounding

Reliable grounding of rack mounted equipment should be maintained. Particular attention should be given to supply connections other than direct connections to the branch circuit (e.g., use of power strips).

Page 4

Before reading this manual

Important Safeguards

In-Text

Symbol Type Description

Caution Important information concerning a specic function.

Note Useful information concerning a specic function.

User’s Caution Statement

Caution: Any changes or modications to the equipment not expressly approved by the party responsible for compliance could void your authority to operate the equipment.

FCC Compliance Statement

THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS FOR A CLASS A DIGITAL DEVICE, PURSUANT TO PART 15 OF THE FCC RULES. THESE LIMITS ARE DESIGNED TO PROVIDE REASONABLE PROTECTION AGAINST HARMFUL INTERFERENCE WHEN THE EQUIPMENT IS OPERATED IN A COMMERCIAL ENVIRONMENT. THIS EQUIPMENT GENERATES, USES, AND CAN RADIATE RADIO FREQUENCY ENERGY AND IF NOT INSTALLED AND USED IN ACCORDANCE WITH THE INSTRUCTION MANUAL, MAY CAUSE HARMFUL INTERFERENCE TO RADIO COMMUNICATIONS. OPERATION OF THIS EQUIPMENT IN A RESIDENTIAL AREA IS LIKELY TO CAUSE HARMFUL INTERFERENCE, IN WHICH CASE USERS WILL BE REQUIRED TO CORRECT THE INTERFERENCE AT THEIR OWN EXPENSE.

WARNING: CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.

THIS CLASS OF DIGITAL APPARATUS MEETS ALL REQUIREMENTS OF THE CANADIAN INTERFERENCE CAUSING EQUIPMENT REGULATIONS.

WEEE (Waste Electrical & Electronic Equipment)

Correct Disposal of This Product (Applicable in the European Union and other European countries with separate collection systems)

This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources.

Household users should contact either the retailer where they purchased this product, or their local government oce, for details of where and how they can take this item for environmentally safe recycling.

Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal.

Page 5

Before reading this manual

The information in this manual is believed to be accurate as of the date of publication even though explanations of some functions may not be included. We are not responsible for any problems resulting from the use thereof. The information contained herein is subject to change without notice. Revisions or new editions to this publication may be issued to incorporate such changes.

The software included in this product contains some Open Sources. You may obtain the complete corresponding source code from us. See the Open Source Guide on the software CD (OpenSourceGuide\OpenSourceGuide.pdf) or as a printed document included along with the User's Manual.

Page 6

Table of Contents

Part 1 – Introduction ......................................... 9

Product Features ................................................................9

Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Overview ......................................................................11

Front Panel ...............................................................................11

Rear Panel ...............................................................................14

Rear Panel Connections .................................................................15

Remote Control ..........................................................................19

Part 2 - Getting Started .....................................22

Setup Wizard ...................................................................22

Camera Registration ............................................................25

Device Scan ..............................................................................25

Advanced Setup: Video In IP Setup ........................................................26

Camera Registration Mode ......................................................27

Live Mode ......................................................................28

Live Menu ...............................................................................28

Zoom ....................................................................................31

PTZ Control ..............................................................................32

Event Monitoring ........................................................................33

Covert Camera ...........................................................................33

Context Menu Access ....................................................................34

Edit Group ...............................................................................34

Video Recording ................................................................34

Panic Recording ..........................................................................34

Audio Recording ...............................................................35

Video Recording Playback ......................................................35

All Channel Playback .....................................................................35

Remote Control Buttons during Playback .................................................35

Context Menu ............................................................................35

Page 7

Table of Contents

Part 3 - Conguration .......................................36

Menu Use ......................................................................36

Text Input via Virtual Keyboard ...........................................................36

Batch Assignment ........................................................................36

Mouse ...................................................................................37

System Setup ..................................................................37

General ..................................................................................37

Date/Time ...............................................................................38

User .....................................................................................39

Storage ..................................................................................41

Monitoring ...............................................................................42

Record Setup ...................................................................44

General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44

Schedule .................................................................................45

Pre-Event ................................................................................46

Event Setup ....................................................................47

Video-Analytics .........................................................................47

Alarm-In .................................................................................50

Video Loss ...............................................................................51

Audio Detection .........................................................................51

Recording Fail ............................................................................52

Camera System ..........................................................................53

General ..................................................................................54

WAN .....................................................................................55

FEN ......................................................................................56

Device Setup ...................................................................57

Alarm-Out ...............................................................................57

Remote Control ..........................................................................57

Display Setup ..................................................................57

OSD .....................................................................................57

Schedule .................................................................................59

Callback .................................................................................59

Mail ......................................................................................59

SNS ......................................................................................60

Camera Setup ..................................................................61

Registration ..............................................................................61

General ..................................................................................62

Advanced Setup .........................................................................63

Page 8

Table of Contents

Stream ...................................................................................68

Audio ....................................................................................69

Upgrade .................................................................................69

Part 4 - Search ..............................................70

Time-Lapse Search .............................................................70

Search Menu .............................................................................71

Time-Lapse Search Menu ................................................................72

Context Menu ............................................................................75

Print .....................................................................................75

Event Log Search ...............................................................76

Overlapped Recording Search ..................................................77

Part 5 - WebGuard ..........................................78

Web Monitoring Mode .........................................................79

Web Search Mode ..............................................................81

Part 6 - Appendix ...........................................83

System Log Types ..............................................................83

Error Code Types ...............................................................84

Troubleshooting ...............................................................86

Specications ..................................................................87

Index ..........................................................................89

Page 9

Product Features

This is a video recorder that supports surveillance, recording, and playback of video from network IP and analog cameras. This NVR (Hybrid Network Video Recorder) unit oers the following features:

• Real-time recording of analog and/or network IP cameras, up to 32 cameras total. User determines exact combination with a maximum of 16 analog inputs.

• Network camera zero conguration

• Conguration-free network camera access

• Supports up to Full HD 960ips video recording

• HDMI out (1) and VGA out (1) ports

• Fast and easy search feature (Time-Lapse, Event log, Motion, Text-In)

• Simultaneously survey, record, play back, and transmit data in real-time

• Graphic User Interface(GUI) and multilingual

• Multiple recording modes (Schedule, Event, Pre-Event, and Panic)

• 2 x USB 2.0 (for connecting peripherals, upgrading software, and saving recording data)

• 6 internal SATA2 HDD bays and 2 eSATA ports

• Two-way audio communication

• 32-channel camera audio recording and 1-channel audio playback

• 16 alarm in and 4 alarm out

• IR remote control-enabled

• Automated system event alerts (industry standard S.M.A.R.T. protocol for HDD status alerts)

Part 1 – Introduction

Gigabit PoE Switch

Audio Out

HDMI Monitor VGA Monitor

Alarm

Alarm Out

USB HDD

Analog Camera

Network Camera

Sensor (1-4)

IR Remote Control

Mouse

Network Connection

Network Video Recorder

Flash Memory

Audio In (1-16)

Page 10

Part 1 – Introduction

Accessories

Upon unpackaging the product, check the contents inside to ensure that all the following accessories are included.

AUDIO 5 AUDIO 6 AUDIO 7 AUDIO 8 AUDIO 9

AUDIO 13

AUDIO 14

AUDIO 15 AUDIO 16

Network Video Recorder Power Cable Quick Guide Multi audio cable

Operation Manual and

Remote Program CD

Optical USB Mouse IR Remote Control SATA2 cables

Rack-mount Kit

Assembly Screws for Adding

Hard

Disk Drives

Page 11

Part 1 – Introduction

Overview

Front Panel

0!@

Camera Buttons

LEDs

Jog Dial, Shuttle Ring

Enter Button

Arrow Buttons

Playback

Buttons

PTZ Button

Alarm Button

Panic Recording Button

Freeze Button

Bookmark Button

Zoom Button

Status Button

Display Button

Menu Button

USB Port

• Some buttons have more than one function.

• Remote control sensor is located on just left of USB ports. Ensure that the sensor remains unobstructed at all times. If obstructed, the sensor might not be able to receive remote control signals.

• Placing a Wi-Fi, Bluetooth, or any other wireless communication device near the NVR may interfere with remote control signal transmission.

• Access various windows and menus using a USB mouse as you would on a personal computer.

• For easier system conguration, a USB mouse is recommended.

Page 12

Part 1 – Introduction

1 Camera Button

Pressing the Camera button while in Live or Playback mode displays images from the selected camera in full screen. Pressing the button 1 displays the camera number 1 and pressing the button 1 again displays the camera number 17. Buttons are also used to enter passwords.

2 LEDs

• Power LED: Lights up while the main unit is in operation.

• Network LED: Flashes when the main unit is linked to an ethernet.

• eSATA LED: Lights up when the main unit is connected to an eSATA device.

• HDD LED: Flashes when data is being written on the HDD or a video search is in progress.

3 jog Dial, Shuttle Ring

Jog Dial

When in the playback mode, you can play video forward image-by-image by turning the Jog Dial clockwise and backward image-by-image by turning the Jog Dial counterclockwise. When in the PIP mode, you can make the PIP screen smaller by turning the Jog Dial clockwise and larger by turning the Jog Dial counterclockwise. When in the Setup mode, you can change number values by highlighting the item in the menu and turning Jog Dial clockwise or counterclockwise to increase or decrease the number.

Shuttle Ring

The Shuttle Ring only functions in the Playback mode. The Shuttle Ring is spring loaded and returns to the center position when released. Turning the ring clockwise plays video forward. Turning the ring counterclockwise plays video backward. Playback speed varies with the amount the ring is turned. The playback speeds are

, , ,

, , and . When you release the ring, it snaps back to the center position and the video pauses.

4 Enter Button

Pressing the Enter button selects options or to register data entries.

5 Arrow Buttons

These buttons are used to select menus and options.

Setup Menu

Up/Down/Left/Right Buttons: Moves the focus up, down, left, or right.

Up/Down Buttons: Increases or decreases values.

6 Playback Buttons

These buttons are used to select menus and options.

Play/Pause (") Buttons

Plays the video in normal speed and displays r on the screen.

Press again during playback to pause the video and display

the screen.

Playback Mode

From paused state:

% Button: To the previous screen & Button: To the next screen Button: Scans backward

through the video at a fast rate. (Press to cycle through

, ,

and

the speed)

! Button: Scans forward through the video at a fast rate.(Press to cycle through

, , and the

speed) Pressing the

button initiates Search mode, which will allow you to search for and play back video recordings. Pressing the

button while in Search mode

returns the screen to Live mode.

Page 13

Part 1 – Introduction

7 PTZ Button

Pressing the PTZ button initiates PTZ mode, allowing you to control PTZ cameras.

In PTZ mode, use the arrow buttons to move the camera up, down, left, and right.

Zoom-Out

Zoom-In

Focus Near

Focus Far

Preset View

Preset SET

8 Alarm Button

Pressing the ALARM button while the alarm has been activated resets all NVR outputs, including the built-in buzzer. Pressing the button while the alarm is o displays the event log on the screen.

9 Panic Recording Button

Pressing the PANIC button displays the

icon and commences recording irrespective of the current schedule.

Press the button again to deactivate Panic Recording mode.

0 Freeze Button

Used to pause Live screen..

! Bookmark Button

Add the current playback point to the bookmark list or move to the registered bookmark point.

@ Zoom Button

Used to zoom in on a specic part of the screen. Once zoomed in, use the arrow buttons to pan around..

# Status Button

Press the Status button to display the status screen.

$ Display Button

Press the DISPLAY button to toggle screen formats.

% Menu Button

Pressing and holding the MENU button for 3 seconds while in Live mode displays the Live menu.

Pressing the MENU button while in Search mode displays the Search menu.

Press the button once more to close the menu. Pressing and holding the MENU button for 3 seconds

while in Playback mode activates One-Touch mode and displays the clip copy window.

^ USB Ports

• Storage Device Connection Connect an external USB hard drive or a USB ash

memory device to one of the USB ports for use with the Clip Copy feature. The external storage device should be placed as close to the NVR as possible. It is recommended that you use a connection cable that is no longer than 180cm in length. Use the connection cable included with your external storage device to connect the device to one of NVR's USB ports. For more information Clip Copy, refer to the 5 Clip-Copy on page 73.

• Peripheral Device Connection Use the USB ports to connect peripherals such as a

USB mouse to the NVR. You can also use a USB-toserial converter and connect multiple text-in devices to the NVR at the same time.

For USB ash memory devices, the NVR supports the FAT32 le format only.

Page 14

Part 1 – Introduction

Connections on the Front Panel

◀

USB HDD

Flash Memory

Mouse

Rear Panel

7 8

Video Input

Video Loop Through

Audio In

Video In Port

Network Port

eSATA Port

RS-485 Port

RS-232 Port

Alarm Connection Ports

HDMI Port

VGA Out Port

Audio Out

Power In Port

Page 15

Part 1 – Introduction

Rear Panel Connections

Video Input

Connect the coaxial cables from the video sources to the BNC Video In connectors.

Video Loop Through

Connect the coaxial cables from the video sources to the BNC Video In connectors.

The Loop BNC connectors are auto terminated. Do NOT connect a cable to the Loop BNC unless it is connected to a terminated device because it will cause poor quality video.

Audio Connection

Connect the audio device to AUDIO IN 1 to AUDIO IN 16 as needed using RCA jacks. Connect AUDIO OUT to speakers with a built-in amplier. Use the provided audio extension cable to connect the audio sources to AUDIO IN 5 to 16.

• This NVR does not feature a built-in audio amplier unit and therefore requires the user to purchase a speaker system with a built-in amplier separately. It's possible to connect an amplied audio source to the NVR, but microphones that do not have a built-in amplier will not function properly if connected to the NVR directly. If this is the case, connect the microphone to the NVR via a pre-amp.

• Check your local laws and regulations on making audio recordings.

Video In Port

• Video In Port

This port does not support PoE. It's possible to establish a network with network cameras and external hubs using a Cat6 cable.

• Green LED on the right will turn on if connected to a 1000 BASE-T network. Orange LED on the left will then ash once a link has been established.

• When using a Cat5e cable, the data transfer speed may decrease depending on how to establish a network.

• If more than 16 cameras from video encoders are registered on the NVR, video may not be displayed smoothly in a remote program.

Network Port

The NVR can be networked using the 10Mb/100Mb/1Gb Ethernet connector. Connect a Cat5e cable with an RJ-45 jack to the NVR connector. The NVR can be networked with a computer for remote monitoring, searching, conguration and software upgrades. For more information on ethernet connection setup, refer to Network Setup on page 54.

Connector directions may vary depending on the NVR

model.

eSATA Connection

Connect external hard drives to these ports.

Page 16

Part 1 – Introduction

Do not connect or disconnect an eSATA device while the NVR is powered on. To connect an eSATA device, rst turn o the NVR and unplug the power cable. Connect the eSATA device and then power the eSATA device rst and then NVR back on. To disconnect an eSATA device, rst turn o the NVR and unplug the power cable. Turn o the eSATA device and then disconnect the eSATA connection cable.

RS-485 Connection

This NVR supports the RS-485 half-duplex serial communication protocol for connecting to external devices such as POS units. The RS-485 connector can also be used to control PTZ (pan, tilt, zoom) cameras. Connect RX+/TX+ and RX–/TX– of the control system to the + and – (respectively) of the NVR.

●●

Connector Pin Outs

Master Unit

Slave Unit

RX → To → TXD

TX → To → RXD

GND → To → GND

RS-232 Connection

Connect an external device such as a POS unit to this port.

• Connector Pin Outs

Master Unit

Slave Unit

RX → To → TXD

TX → To → RXD

GND → To → GND

Refer to the following for pin-out details for the 9-pin connector of the slave unit.

Male Female

Pin 2

RXD (Receive Data)

Pin 3

TXD (Transmit Data)

Pin 5

GND (Ground)

Alarm Connection

Connect alarm connectors to these ports.

Press down on the button and insert the cable into the opening. Release the button and then pull on the cable slightly to ensure it is held securely in place. To disconnect the cable, press down on the button again and pull the cable out.

Page 17

Part 1 – Introduction

• Alarm In 1 through 16

This NVR is capable of responding to event signals from external alarm in devices. Connect mechanical or electrical switches to AI 1 through 16 and the GND (ground) connector. In order to be recognized by the NVR, the signal from an alarm in device must be less than 0.3V and maintained for at least 0.5 seconds. The alarm in voltage range is 0V to 5V. For more information on alarm in setup, refer to the Alarm-In on page 50.

• GND (Ground)

Connect alarm in or out's ground cable to the GND connector.

All connectors marked "GND" are common connectors.

• NC/NO (Relay Alarm Outputs)

This NVR is capable of activating/deactivating buzzers, lights, and other external devices. Connect a mechanical or electrical switch to C and NO connectors. NC/NO is

a relay output which sinks 2A@125VAC and 1A@30VDC. For more information on alarm out setup, refer to the

Alarm-Out on page 57.

ARI (Alarm Reset In)

An external signal to the Alarm Reset In can be used to reset both the Alarm Out signal and the DVR’s internal buzzer. Mechanical or electrical switches can be wired to the ARI (Alarm Reset In) and GND (Ground) connectors. The threshold voltage is below 0.3V and should be stable at least 0.5 seconds to be detected. Connect the wires to the ARI and GND connectors.

• Connector Arrangement

ALARM IN

1 through 16

Alarm In 1 through 16

GND Ground

Relay Alarm Out (Normally Closed)

C Relay Common

Normally Open Relay Alarm Out

ARI Alarm Reset In

Monitor Connection

Connect to the VGA OUT or HDMI port.

Power Cable Connection

Connect the power cable to this port. This NVR does not feature a separate power on/o button and will turn on the moment power is supplied.

• Organize the power cable so that it will not cause people to trip over or become damaged from chairs, cabinets, desks, and other objects in the vicinity. Do not run the power cable underneath a rug or carpet.

• The power cable is grounded. Do not modify the power plug even if your power outlet does not have a ground contact.

• Do not connect multiple devices to a single power outlet.

Page 18

Part 1 – Introduction

Factory Reset

Located next to the Audio Out port on the rear of the NVR is a switch that, once activated, will reset the NVR to all its initial factory settings.

A factory reset will clear all NVR settings congured by the user.

You will need a straightened paper clip to access the factory reset button.

Turn o the NVR.

Insert a straightened paper clip into the factory reset switch hole and press the switch. Turn on the NVR while holding the switch.

Press and hold until you hear 2 beeps from the NVR's internal buzzer.

All NVR settings will be returned to their factory values once you remove the paper clip.

Connections on the Rear Panel

Speaker

VGA Monitor

HDMI Monitor

Network Camera

Remote Monitoring

Keyboard

Sensor

Alarm

Power

POS

eSATA Storage Device

Network

Analog Camera

Microphone

Page 19

Part 1 – Introduction

Remote Control

ID Button

DISPLAY Button

SEQUENCE Button

FREEZE Button

ALARM Button

Camera Buttons

FOCUS NEAR/FAR Button

PRESET SET/VIEW Button

ZOOM IN/OUT Button

MENU Button

PTZ Button

Arrow Buttons

Enter Button

ZOOM Button

PANIC Button

Playback Buttons

Page 20

Part 1 – Introduction

1 ID Button

Used to assign remote control ID values. No additional remote control assignment is

necessary if the system's ID is 0. If the system's ID is a number between 1 and 9, however, you will need to press the ID button and then press the system ID number (1 through 99) on the remote control. The

(remote control) icon will appear on the upper right corner of the NVR screen (status indication area) to indicate successful system-to-remote control pairing. If using multiple systems, it's possible to control all the units with a single remote control as long as all the system IDs are 0. For more information on system IDs, refer to the System Setup on page

37.

2 DISPLAY Button

2x2 > 1p5 > 1p7 > 3x3 > 4x4 > 5x5 > 6x6

3 SEQUENCE Button

Pressing the SEQUENCE button while in Live mode initiates Live Sequential mode (displays channels in sequence).

4 FREEZE Button

Used to pause Live screen.

5 ALARM Button

Pressing this button while the alarm has been activated resets all NVR outputs, including the builtin buzzer. Displays the event log on the screen when the alarm is o in Live mode.

6 Camera Buttons

7 FOCUS NEAR/FAR Button

Used in PTZ mode to shift focus between a nearby point and a far away point.

8 PRESET SET/VIEW Button

Press the SET button while in PTZ mode to save the current position as a preset. Pressing the VIEW button displays the preset list.

9 ZOOM IN/OUT Button

Used in PTZ mode to zoom in/out on the screen.

0 MENU Button

Pressing the MENU button while in Live mode displays the Live menu. Alternatively, pressing the

button while in Time-lapse Search mode displays the Control Area menu. Using the menu button in the

control area, you can move the screen. Top by using this button in the Control Area menu displays the Search menu. For more information on the Control Area menu, refer to Time-Lapse Search in the operation manual. Pressing and holding this button for 3 seconds activates One-Touch mode and displays the clip copy window while in Time-lapse Search mode. If the Search menu is displayed on the top of the screen, One-Touch mode is not activated.

! PTZ Button

Initiates PTZ mode and allows you to control the selected PTZ camera.

@ Arrow Buttons

Used to navigate through menus and interact with GUIs. In a Setup menu, use the Up/Down Arrow buttons to increase or decrease numerical values. In Live or Playback mode, use the Left/Right Arrow buttons to view the previous or next screen.

# Enter Button

Used to make menu option selections and register data entries. In addition, pressing this button while a camera screen is selected by pressing the Menu button in Live or Playback mode displays the Camera menu.

$ ZOOM Button

Used to zoom in on a specic part of the screen. Once zoomed in, use the arrow buttons to pan around.

% PANIC Button

Pressing this button commences recording irrespective of the current schedule.

Press the button again to deactivate Panic Recording mode.

Page 21

Part 1 – Introduction

^ Playback Buttons

Scans backward through the video at a fast rate. (Press to cycle through

, , and

the speed)

Plays the video in normal speed and displays r on the screen. Pressing the "qbutton during playback pauses the video and displays

on the screen.

Scans forward through the video at a fast rate. (Press to cycle through

, , and the

speed)

Stops the video and restores Live mode.

Skips to the previous screen (while in paused state).

Skips to the next screen (while in paused state).

Page 22

Setup Wizard

Setup Wizard lets you congure basic settings required for operating the system.

Setup Wizard only appears during initial booting. When you login as an administrator account after initial booting, you can use Wizard to go to Live menu and select Wizard.

Select a system language.

Select Cancel from any of the Wizard screen to cancel the setup process and return to the main setup menu.

Quick Wizard

Select Quick Wizard.

Specify the current date and time and then click Next.

• The new date and time settings will only be applied after clicking Next.

• For more information on date and time settings, refer to the Date/Time section under System Setup on page 37.

Part 2 - Getting Started

Page 23

Part 2 - Getting Started

Choose the desired Recording Method and click Next.

Choose the desired Recording Quality and click Next.

• Higher recording quality uses up more disk space.

• Recording resolution is determined based on the selected recording quality.

– High Video Quality Priority Prole: Very

high

– Standard Recording Prole: High

– Longer Recording Time Priority Prole:

Standard

– Recording resolutions used under each recording method

and record video quality setting are as follows:

High Video Quality Priority Prole

Standard Recording Prole

Longer Recording Time Priority Prole

Motion Event Record

Very high High Standard

Continuous & Motion Event Record

Very High (Continuous) /

Very high (Motion)

High (Continuous) / High (Motion)

Standard (Continuous) / Standard (Motion)

Continuous Very high High Standard

Click Finish to exit Quick Wizard.

Network Wizard

After exiting from Quick Wizard, the network with Network Wizard will start automatically.

Select Network Wizard.

Page 24

Part 2 - Getting Started

Specify whether the system is connected to the Internet and click Next.

If you have chosen No, wait for the test to nish and then click Finish to exit Network Wizard.

Select Network Conguration and then click Next. Select either Auto Conguration or Manual Conguration and then click Test to test the system's current network conguration.

• This test must be performed before proceeding to the next step.

• If the NVR is on a network connected to a network that has a DHCP server, selecting Auto Conguration retrieves LAN settings such as IP and DNS addresses automatically. Selecting Manual Conguration, on the other hand, lets you specify the settings manually.

• UPnP support device not found. If this error message is displayed, check to see if the IP router (or NAT) supports UPnP and if UPnP has been enabled. For more information about the router's UPnP function, refer to the router's operation manual.

Enter in the Device Name eld the NVR name to be registered on the FEN server and then click Check to check its availability.

• The device name you register on the FEN server will be a unique name used to identify the NVR. Once registered, the name can be used to access the NVR directly from clients such as iRAS . Check the name's availability to complete the registration process. The Finish button will then become activated.

• You will be prompted with an error message if you do not enter a name for the NVR or enter a name already registered on the FEN server.

• Depending on the network environment, FEN services may not be active and therefore prevent the NVR from connecting to the network. In this case, you will need to manually congure the ports. For more information on port conguration, refer to Network Setup on page 54.

Click Finish to exit Network Wizard.

Page 25

Part 2 - Getting Started

Camera Registration

Once Network Setup Wizard is complete, 16-channel analog cameras are automatically registered and click the Scan button to scan for network cameras connected to NVR. By deleting some or all of the 16 registered analog cameras, you can register analog and/or network IP cameras, up to 32 cameras (User determines exact combination with a maximum of 16 analog inputs).

• Title: Indicates the camera's title. Left-click on the title to edit the camera's title.

• MAC Address: Displays the last 6 digits of the camera's MAC address.

• Address: Indicates the camera's searched IP address.

• Model: Indicates the network camera's model or "analog" if they are the analog cameras.

Device Scan

Click the "Scan" button and the Device Scan screen appears.

Some functions may not be supported for the third party cameras depending on their protocol and model.

• Protocol: Select the protocol used by the camera (or video encoder) you wish to search for.

Even if the network device uses a protocol supported by the NVR, the device itself may not be visible for scanning and registration by the NVR. For more information about supported network devices and models, contact your retailer.

• Mode: Select the scan mode.

- Auto Scan (LAN): Lists cameras in a LAN environment. If Auto Scan (LAN) fails to recognize a camera, try using IP Address Scan instead.

- IP Address Scan: Enter the IP address of a camera. The NVR scans for the camera matching the specied address. If you enter IP address's range, the NVR scans for cameras falling under the specied address's range. By specifying an IP address, you can also specify which port to use with the Remote Admin feature. It is recommended that the camera not be networked via DHCP (Dynamic Host Conguration Protocol). If the camera is networked via DHCP, connection to the camera may not be made properly depending on changes in the external network environment.

1 Mac Address: Displays the last 6 digits of the

camera's MAC address.

2 Address: Indicates the camera's searched IP address.

3 Model: Indicates the network camera's model or

"analog" if they are the analog cameras.

4 Name: Indicates the camera's name.

5 Status: Identies the camera's registration status

"registered" or "not registered."

Page 26

Part 2 - Getting Started

Advanced Setup: Video In IP Setup

If the camera is networked but not scanned, use this setup. This setup allows you to change the network setting of the NVR's VIDEO IN port which is camera's network environment. Check the camera's network setting rst before you use this setup.

Make sure that this setting does not conict with the WAN setting. For more information on the WAN setting, Refer to WAN on page 56.

- Link-local address: Indicates the default IP address.

- Manual: Allows you to enter the IP address and other network settings manually.

- DHCP Client: Retrieves an IP address and other network settings automatically from a DHCP server.

- DHCP Server: It makes the NVR run as a DHCP server. Check if there is any DHCP server in the same network. If there is no DHCP server, this option is enabled. The NVR allocates an IP address automatically in the range of 10.10.0.128 to 10.10.254.254 by using DHCP to the camera connected to the NVR's VIDEO IN port. On DHCP Server, Video In Network is connected between NVR and network cameras only, so Gateway does not have any meaning. Subnet Mask is

255.255.0.0(Class B).

• When several NVRs exist in the same network, only one of NVRs has to be run as a DHCP server. If several DHCP servers are running, the redundant IP may be allocated to the camera.

• The range of 10.10.0.1 to 10.10.0.127 is not recommended because NVR system already has the IP address.

Page 27

Part 2 - Getting Started

Select Scan to commence scanning.

• Only cameras that are connected to the NVR via VIDEO IN ports can be scanned and registered.

Select a camera from the scan list and then select Add Camera. The device login window will appear.

Enter a User ID and a Password for the selected camera.

- Apply to All Devices: Selects to apply the same user and password to all selected devices if you selected more than one device and the selected devices have the same user ID and password.

Camera Registration Mode

While in Live mode, right-click and select Camera Registration.

Conguring the NVR's settings and accessing its searching and other functions require an authorized user login.

While in Live mode, right-click on the mouse and select Login and either press the SETUP button on the remote control.

Select a user, enter the password, and then select OK.

• There is no default password for the admin account. Select admin and then OK without entering a password to log in.

• Leaving the admin account unassigned with a password poses a security risk. Please assign a password at your earliest convenience. A warning message will continue to be displayed until a password is assigned.

• Click on the

button next to the password eld using the mouse. This will bring up a virtual keyboard you can use to assign a password. For more information on using the virtual keyboard, refer to the Text Input via Virtual Keyboard on page 38.

To log out, right-click on the mouse and select Logout.

Page 28

Part 2 - Getting Started

Live Mode

Live Menu

Press the MENU button on the NVR's front panel while in Live mode to bring up the Live menu on the right edge of the screen. Press MENU button once more to hide the menu. Use the Arrow buttons on the remote control to select the menu options.

5 6 7 8

9 0 ! @

Layout

Display

Previous Group, Next Group

Search Mode

Select Camera

Sequence

Freeze

Panic Recording

Alarm

Status

Wizard

Setup

Status Indication

Placing the mouse pointer near the right edge portion of the screen also displays the Live menu.

Page 29

Part 2 - Getting Started

1 Layout

Used to change the screen layout to single screen, 2x2, 1p5, 1p7, 3x3, 4x4, 5x5, or 6x6.

2 Display

• OSD (On Screen Display): Enables/disables the OSD feature.

• Aspect Ratio: Select whether to enable the original aspect ratio of video transmitted from the camera.

3 Previous/Next Group

Loads the previous/next screen group.

4 Search Mode

• Time-Lapse Search: Select Search Mode > Time- Lapse Search to search for and play back saved data directly from the record table.

• Event Log Search: Select Search Mode > Event Log Search to search for event logs and play back associated event recordings.

5 Select Camera

Displays the selected camera in a single screen format.

6 Sequence

Initiates Sequence in the same manner as pressing the SEQUENCE button on the remote control while in Live mode. To exit, select Sequence once more or press the SEQUENCE button. The

icon is displayed on the bottom left part of the screen while Sequence is in progress.

Full Sequence

Displays all channels in sequence while in Live mode (single and split screen settings). In order to use the Full Sequence feature, Full Sequence (Display Setup - Main Monitor > Sequence) must rst be enabled.

e.g.) Full Sequence

Cameo Sequence

In Cameo Sequence mode, only the bottom right screen in a split screen setup changes sequence. In order to use the Cameo Sequence feature, Cameo Sequence (Display Setup - Main Monitor > Sequence) must rst be enabled.

e.g.) Cameo Sequence in 2x2 split screen mode

• If using the Full Sequence setting, page numbers appear on the system status area on the bottom left part of the screen, next to the Sequence icon.

• Pages are skipped under the following circumstances:

– If all cameras included in the page are

deactivated.

– If there are no video signals.

– If the page contains "covert" cameras.

– If the user does not have permission to view

feeds from the cameras.

7 Freeze

Freezes the screen. Select Freeze again to unfreeze.

8 Panic Recording

Activates/deactivates Panic Recording

9 Alarm

Pressing this button while the alarm has been activated resets All NVR outputs, including the built in buzzer.

Page 30

Part 2 - Getting Started

0 Status

Event

This screen displays an overview of all events. When an event occurs, the corresponding channel

ashes for 5 seconds.

Event Types

Alarm-In Check Alarm-In

Motion Video Loss

Audio Detection Trip Zone

Tampering Tex t-In

Recording Fail Fan Error

• Panic Record: Displays event status based on current Panic Record status.

• Check Recording: Displays event status based on System Monitoring settings. For more information, refer to the Monitoring on page 42.

• Disk Almost Full/Disk Full: If the storage device is not in Recycle status, event status is displayed when the amount of disk space specied under System Monitoring is reached and when the disk becomes 100% full. For more information, refer to the Monitoring on page 42.

• Fan Error: Event is indicated when the cooling fan cannot reach a certain RPM or fails for longer than 50 seconds.

• eSATA Disconnected: Event status is displayed when an eSATA device is abruptly disconnected.

• Disk Cong Change: It will be highlighted when the NVR reboots after the hard disk drive has been replaced.

• No Storage Found: It will be highlighted when no recordable storage device has been found.

Storage

Indicates each disk's status.

• Disk Bad

Not Formatted

A disk that has never been used before.

Good

• Disk performing normally.

• If the HDD is partially damaged, indicates the bad sector percentage.

Error

• If the HDD's bad sector ratio is higher than as designated by the user.

• Generates a system event.

• Temperature

N/A

Unable to detect the disk's temperature.

Good

Operating within normal temperature range.

Bad

• Disk temperature higher than as designated by the user.

• Generates a system event.

• S.M.A.R.T.

N/A

A disk that does not support S.M.A.R.T.

Good A disk with normal S.M.A.R.T. status.

Bad

A disk with abnormal S.M.A.R.T. status. Possibility of damage within 24 hours.

Page 31

Part 2 - Getting Started

• Congure Disk Bad and Disk Temperature settings under Setup > System > Monitoring.

• Check each disk's data storage time information under Recording Data.

• For the mirroring disk, clicking the temperature, S.M.A.R.T can check the each HDD information.

! Wizard

Launches the Setup Wizard.

@ Setup

Used to access the Setup menu.

Status Indication

Displays system status icons.

Status Indication

Indicates remote control receptivity.

Indicates connection to the NVR from a remote program.

Indicates two-way audio connection.

Indicates connection to the NVR using the VNC service.

Indicates a zoomed in state.

Indicates Freeze is in use.

Indicates Sequence is in use.

1/4 Indicates the current screen's group.

Indicates an event monitoring.

Indicates HDD use. The icon to the left is shown if using the overwrite setting. Otherwise, remaining HDD space is shown as a percentage value.

Zoom

Press the ZOOM button on the remote control and select a channel you wish to zoom in on. A zoom frame will appear on the selected channel. Use the arrow buttons to position the frame. Press the Play/Pause button to cycle through various zoom factors. When Zoom is activated,

icon is on the status bar located

on the bottom left corner of the system.

• In Full Screen mode, activating Zoom automatically selects the current channel.

• To restore the channel to normal size, press the Zoom button again.

Page 32

Part 2 - Getting Started

PTZ Control

While in Live mode, right-click and select PTZ from the context menu or press the PTZ button on the NVR's front panel or remote control to display the PTZ camera selection window.

Select the camera you wish to control. The icon will begin to ash on the selected camera's OSD window.

Use the Arrow buttons to pan and tilt the camera up, down, left, and right.

Use the

and buttons to zoom in/out.

Use the

and buttons to shift focus from nearby to

far and vice versa. Use the

button to load the preset window.

Use the

button to save current position as a preset.

You can also change the direction by dragging on the mouse.

Also, it's possible to use the mouse wheel to zoom in/ out.

• Logging in with an account that has PTZ Control Authority is necessary in order to control PTZ cameras.

• A message will prompt if there is no PTZ camera displayed on the Live screen.

• Zoom in/out and shift focus using the PTZ Control (ZOOM, FOCUS) buttons on the remote control.

• To exit PTZ mode, press the PTZ button again.

Setting Up a PTZ Preset

While in PTZ mode, select the VIEW button on the remote control to display the Set Preset window and assign the current position as a preset.

While in PTZ mode, select the SAVE button on the remote control to display the Move to Preset window. Select a preset to move the current PTZ camera to the selected preset's position.

Page 33

Part 2 - Getting Started

Advanced Settings

In PTZ mode, selecting a camera and then clicking Menu button loads the Advanced PTZ screen as shown below. You can load the Advanced PTZ screen also by pressing the Play/Pause button and then SETUP button on the front panel. This menu lists Speed, Auto Pan, and other advanced PTZ camera control options available for the camera. Options that are not available for the selected PTZ camera remain inactive.

You can use the mouse to control PTZ cameras. Leftclick on the mouse and drag to move the camera in the desired direction and use the mouse wheel to zoom in/out.

While in PTZ mode, place the mouse pointer close to the bottom edge of the screen to display the PTZ Tools window.

PTZ Camera Pan and Tilt

Zoom In/Out

Focus Near / Far

IRIS Open / Close

One Push

Set / Move to Preset

Device Menu supported by the camera

• The exact PTZ protocol supported by the camera must be specied in order to use the NVR's PTZ controls.

• Drag and drop to reposition the PTZ Tools window.

• Select the

icon to hide the PTZ Tools window.

Event Monitoring

When an event occurs, the NVR automatically changes to the camera screen linking event monitoring and shows the

icon on the system status area on the bottom left portion of the screen. To use the Event Monitoring feature, navigate to Display Setup > Main Monitor and enable Event Monitoring. Event Monitoring remains in eect throughout the entire Linked Dwell Time. After that, the NVR will return to the previous screen if a new event does not take place. Pressing the Layout or a Camera button before the end of the Linked Dwell Time reverts the system to Live mode.

Covert Camera

Use this feature to assign Covert Camera View permissions.

Navigate to Camera Setup > General and designate cameras as Covert 1 or Covert 2.

• Covert 1: Hides images from the camera in Live mode but does indicate the camera's title and status via icons.

• Covert 2: The camera is indicated as being inactive. Images from the camera are not shown. Camera title and status icons are not shown.

Users that have a cover Covert Camera View are able to view both images from and status icons for all Covert 1 and Covert 2 cameras.

Page 34

Part 2 - Getting Started

Context Menu Access

While in Live mode, press the remote control's button and then the Menu button to display the Context Menu window. You can display the Context Menu window also by pressing the Play/Pause button and then SETUP button on the front panel. Alternatively, right-click on the mouse to access the Context menu.

• PTZ: Access PTZ controls.

• Zoom: Zoom in.

• Audio: Enable/disable audio. (This function supports only in single screen.)

• Color Control: Select a channel to display its Color Control window. Adjust the selected camera's brightness, contrast, saturation, and hue settings.

• Microphone: Enables audio transmission to a remote locale via microphone(This function only supports cameras with two-way audio).

Even if two-way audio communication is set up between the NVR and camera, the microphone connected to the NVR will terminate automatically when the microphone on the remote is turned on(The remote microphone takes priority).

• Information: Select a network channel to display information about the selected channel's device.

• Edit Group: Rearrange the split screen layout.

• Camera Registration: Activate Camera Registration mode.

• Login/Logout: Log into the account or log out of the account.

Edit Group

Edit Group lets you customize split screen pages in both Live and Search modes.

While displaying a split screen page, select the Edit Group option from the context menu. A yellow

border is drawn around the page. Use the arrow buttons on the front panel or the mouse to select a dierent page.

Press a Camera button or select a camera after pressing the Menu button. Selected camera is then loaded on to the selected page. Repeat to assign

other channels to the page.

Press the remote control's button to exit Edit Group. Alternatively, press the Menu button and then select Exit Group Edit to exit.

Edit Group will terminate automatically after 15 seconds of inactivity.

Video Recording

Video recording will only take place if all the connections are made correctly as per information contained in Part 2 of this operation manual.

For more information on video recording settings, refer to the Record Setup on page 44.

Panic Recording

Select Live or Search menu's Panic Recording icon or press the PANIC button on the front panel or the remote control to commence panic recording on all registered cameras.

To stop Panic Recording, select the Panic Recording

icon or press the PANIC button again. If the Panic

Recording Duration option under Record Setup > General has been congured, Panic Recording will

automatically terminate after the specied duration of time has elapsed. For more information, refer to the Record Setup on page 44.

• Panic Recording takes place irrespective of any recording schedule set up by the user.

• Panic Recording video prole from Record Setup – General applies to all Panic Recording videos.

Panic Recording will not take place if recording mode is not set to Recycle and the HDD has reached 100% of its capacity.

Page 35

Part 2 - Getting Started

Audio Recording

If the Record Audio option under Record Setup > General has been enabled, the camera will record audio

along with video. For more information, refer to the Audio on page 69, Record Setup on page 44.

Check your local laws and regulations on making audio recordings.

Video Recording Playback

You can play back video recordings by using mouse or remote control.

• Login with an account that has search permission is needed to playback video recordings.

• The initial video playback point in Search mode is the recording's last playback point or the end of the recording data.

• Audio playback of the selected recording is available in full screen mode only.

• Covert protection on cameras also applies to video recording playback.

All Channel Playback

Press the Menu button while in Live mode.

Select the Search Mode icon and then select Time-Lapse Search or Event Log Search.

The selected search mode will be initiated.

For more information on data search, refer to the Part

4 - Search on page 70.

Remote Control Buttons during Playback

Camera Button: Displays the selected recording in full screen.

Zoom Button: Allows you to zoom in on a specic area of the recording.

Layout Button: Cycle through 1x1, 2x2, 1p5, 1p7, 3x3, 4x4, 5x5, and 6x6.

Context Menu

While in Search mode, press the remote control's

button and then the Menu button to display the Context Menu window. Alternatively, right-click on the mouse to access the Context Menu.

• Zoom: Zoom in.

• Audio: Enable/disable audio. (This function supports only in single screen.)

• Edit Group: Rearrange the split screen layout.

Page 36

Menu Use

Information contained in this section (Menu Use) applies to all other instructions found throughout Part

3 - Conguration.

While in Live mode, press the remote control's SETUP button or select Live menu > Setup using the mouse.

System Setup

Record Setup

Event Setup

Network Setup

Device Setup

Display Setup

Notication Setup

Camera Setup

Use the remote control's arrow buttons to select an option and then press the remote control's button or left-click on the option using the mouse.

Change the setting and then select Apply or OK to save the change.

To apply default settings, select the Default button located on the left bottom corner of the setup window.

Text Input via Virtual Keyboard

Use the remote control's arrow buttons to select a virtual keyboard key and then press the remote control's

button or click on the key using the mouse.

Toggle case.

Deletes the character to the left of the cursor.

Deletes the character to the right of the cursor.

Converts keyboard.

Batch Assignment

Certain table-format menus such as the shown in the Record Setup on page 44 allow you to change the title value. In this case, changing the title value simultaneously changes all other entry values on the same row.

Part 3 - Conguration

6 7 8

Page 37

Part 3 - Conguration

Mouse

Using a mouse makes it easier to congure the settings. A mouse lets you make selections faster and use its wheel to scroll through long menus. You can also use the mouse wheel to increase/decrease numerical values.

System Setup

Refer to the Menu Use on page 36 for basic information on using the Setup menus.

General

This Setup menu contains general system options.

• Site: Used to enter a description about the system's installation site (no description by default). You can edit the information using the virtual keyboard.

• System ID: Used to identify the NVR apart from other NVRs. System ID is also used to control the NVR with the remote control.

The default System ID is 0 and can be changed to a value between 0 and 99. The System ID can also be entered using the virtual keyboard.

• Language: Choose a language.

• Version: Indicates the software version.

• Upgrade: Select to upgrade the system. Selecting Upgrade displays the USB search window. You will then be able to select an upgrade package and upgrade the system. Once the upgrade is complete, the NVR will reboot automatically.

If an upgrade attempt fails, an upgrade failure message will be displayed. Refer to Error Code Types on page 84 for more details.

• Setup: Exports current NVR settings or imports existing settings.

• Import: Decide whether to import network settings as well. If you do not wish to change the current network settings, do not select Include Network Setup.

Selecting Setup Import does not change the settings below.

• Time-related settings (Date/Time, Time Zone, and Use Daylight Saving Time)

• Camera-related Advanced Settings

• Camera-related Stream settings (Only if the resolution is dierent from the camera in exporting)

• Export: Exports the current system settings to a storage device connected to the system's USB port. You can designate a File Name for the export le.

For USB ash memory devices, the NVR supports the FAT32 le format only.

• Show System Log: Displays a searchable list of 5,000 most recent system log entries. For more information on types of system log entries, refer to the System Log Types on page 83. The icon appears next to log entries originating from a remote source. To export the system log, select the Export at the bottom of the screen and then designate a le name.

Page 38

Part 3 - Conguration

In order to display the system_log.txt le, you must use the correct character encoding settings and use a xed-width font.

• Clear All Data: Erases all recording data. Selecting

Clear All Data displays a conrmation window. Select Clear to proceed.

• Before you perform Clear All Data, make sure you are not accidentally deleting important data. Erased data cannot be recovered.

• Clear All Data does not aect the system log. Instead, the Clear All Data event will be added to the log.

• System Shutdown: Shuts down the system. When prompted, select System Shutdown.

• The system will restart after changing the channel mode.

Date/Time

• Date: Used to change the system's date setting.

• Time: Used to change the system's time setting.

• Date Format/Time Format: Used to change the system's date and time formats.

• Time Zone: Used to designate the system's time zone.

Refer to the map displayed on the screen and change the time zone using the mouse or the arrow buttons.

• Use Daylight Saving Time: Enables DST correction.

• Time Sync.: Select a time server for the system to synchronize with.

Select Automatic Sync.

Enter the Time Server's IP address or domain name or select

and then choose a server from the list of

registered time servers.

Specify the server synchronization Interval.

Select OK to apply and exit.

• If you have congured the DNS Server setting under Network - WAN, you can enter the time server's domain name instead of its IP address.

• Selecting Run as Server sets the current NVR as a time server for other NVRs within the system.

• Holiday: Designate holidays. On specied holidays, recording takes place according to the holiday recording schedule specied under Record Schedule.

Select the + button at the bottom of the window.

Select a date.

Select OK to apply and exit.

Select the icon to delete the existing holiday date.

Page 39

Part 3 - Conguration

User

Use this option to register users and assign permissions.

Select + Group and enter a group name. A group name can be up to 15 characters in length.

Specify the group's permission settings. For more information on permission settings, refer to the Group Permissions on page 40.

Select + User and then enter a user name.

Select a group for the user and then enter a password. The password can be up to 16 characters in length and may include letters, symbols, and numbers.

Select OK.

Congure Auto Login and Auto Logout settings.

Select Apply or OK to exit.

• Group names, user names, and passwords can be entered using the virtual keyboard. For more information on using the virtual keyboard, refer to the Text Input via Virtual Keyboard on page

36.

• To delete a registered user or group, select the icon on the right of the corresponding user/group. Group Administrator and User admin cannot be deleted.

• Select the

icon next to Group & User on the top of the screen to delete all groups and users except Group Administrator and User admin simultaneously.

• A password entry is required to edit existing groups and users.

• Group Administrator's permissions cannot be changed.

• With the User admin account, only the password can be changed.

• When the system starts up, it will automatically log into the account designated under Auto Login.

• The system will automatically log out of the account if the duration of inactivity specied under Auto Logout.

• Access other account in administrator group to change the user name.

Page 40

Part 3 - Conguration

Group Permissions

System Shutdown May shutdown the system from the system menu.

Upgrade May upgrade the system from the system menu (System Setup).

Color Control May adjust each camera's brightness, contrast, saturation, and hue settings.

System Check May view System Check results.

PTZ Control May control PTZ cameras.

Alarm-Out Control

May reset in the event of an alarm-out. Alarm-outs can be reset by pressing the Alarm button on the device or

selecting the Alarm-Out Control button on the remote program.

Covert Camera View May access covert cameras in Live and Search modes.

Search Clip Copy

The user who has permission for Clip Copy can perform Clip Copy. If the user does not have permission, Clip Copy is not allowed but only search is allowed.

Setup

System Time Change

May change the system's date and time settings.

Data Clear May clear data stored in the system.

PTZ Setup May congure PTZ settings.

Alarm-Out Setup May congure alarm-out settings.

Covert Camera Setup

May congure convert camera settings.

Record Setup May congure recording settings.

VNC May access the NVR and control it remotely via network.

Setup Import May import previously saved NVR settings.

Setup Export May export current NVR settings.

Page 41

Part 3 - Conguration

Storage

Use this option to congure storage settings.

• Type: Indicates the type of the installed disk.

• Capacity: Indicates the disk's capacity.

• Format: If the disk has been formatted, indicates either Record or Not Using. If you have connected an unformatted storage device, the Use As value will be indicated as Not Formatted.

• Information: Indicates if the disk is being used for recording purposes. Disks that were used in dierent systems will show up as Other. Select Information to check the saved data's time information or select Delete to erase the data.

• Select Format to prepare the disk as a storage for data recording.

• Disks formatted with Use As set to Not Using will not be used for data recording.

• This NVR supports SATA2 HDDs.

Mirror

The NVR supports function that records the same data on the two disks at the same time. You can set up mirroring by selecting Storage in the System menu and then selecting Setup in the Mirror. Up to three Mirrors are supported.

This function only works if the two internal hard disks have the same capacity and model.

• If you change the setup related to Mirror, you must reboot the system.

• A disk problem may cause mirroring to stop. The separated disk can be used to reboot the system.

• Internal HDD: Indicates the available disks for mirroring.

• Setup: Congure detailed settings related to Mirror.

– Mirror: Click OK to start mirroring. Once you start

mirroring (writing data on the two disks at the same time between two disks), all existing data on the two disks will be erased.

Once you start mirroring, all existing data on the two disks will be erased. Please be careful not to designate the wrong disk by mistake.

Page 42

Part 3 - Conguration

– Stop: Once mirroring starts, you can stop it by

selecting Stop option and then designating disks to delete. Once mirroring is stopped, all existing data on the disk will be erased.

When mirroring is stopped, the deleted disk will be set to NOT Used. If you want to use the disk for recording, you must reformat it.

Mirror number 1 and 2 cannot resynchronize at the same time.

– Resync: Once you start mirroring, the two disks

will be resynchronized, which means that all data on the destination disk will be erased and the data on the source disk will be copied to the destination disk. Select the Resync option, designate the source disk, and then click OK. When you click OK, all data on the destination disk will be erased. After resynchronization is complete, mirroring will start.

When you try resynchronizing, the disk that has never tried mirroring cannot be selected as the source disk.

Once you start mirroring, all data on the destination disk that designate as the source disk will be erased.

Please be careful not to designate the wrong disk by mistake.

• Information: Indicates if the installed disk is being used for mirroring or Resync purposes. Select information about mirroring to check the disk’s model and serial number.

Monitoring

Use this option to congure Monitoring settings.

• Settings: Congure when and what the system should monitor for.

• Actions: Congure alarm-out (NVR alarm-out channel, NVR beep, camera alarm-out channel)and notication (email, LAN1 through 5, SNS, alert window) settings.

Page 43

Part 3 - Conguration

Monitoring Options

System

Dene monitoring times. If self-diagnosis is not performed on a regular basis, the system will assume an error.

Bootup, Restart, Shutdown

Dene bootup, restart and shutdown actions.

Panic Record Dene panic recording actions.

Check Recording

The system will assume an error if the system has been scheduled to record normally but recording does not take place during scheduled intervals.

Select Schedule On and then congure the days of the week, times, and monitoring interval. Select the button on the bottom left of the screen to add a schedule. Select to delete the schedule.

Check Alarm-In

The system will assume an error if the alarm-in status does not change during the specied monitoring interval while alarm-in is active.

Disk Almost Full Generates an event if the disk reaches the specied capacity (80% to 99%).

Disk Full Generates an event when all disks reach their maximum capacity.

Disk Bad

Generates an event when the specied percentage of the disk becomes damaged. Set to between 10% and 90% in 10% intervals.

Disk Temperature

Specify the threshold temperature. Once any disk reaches this threshold, the system will issue an alert.

Disk S.M.A.R.T.

Monitors disks that support S.M.A.R.T. and noties the user if a disk error is detected.

Fan Error Noties the user when the fan inside the system malfunctions.

eSATA Disconnected Noties the user if an eSATA device becomes disconnected while in use.

Disk Cong Change It will be highlighted when the NVR reboots after the hard disk drive has been replaced.

No Storage Found It will be highlighted when no hard disk drive has been connected.

• For system events, only an e-mail notication of actions can be selected.

• In order to use the Notify(Callback) feature, the NVR must be registered to the remote program on the receiving PC's end.

Page 44

Part 3 - Conguration

Record Setup

Refer to the Menu Use on page 36 for basic information on using the Setup menus.

General

Congure general recording settings.

• Recycle: When the recording disks become full, the system overwrites existing data with new data, starting with the oldest rst. If Recycle is disabled, recording will simply stop when the recording disks reach their maximum capacity.

• Record Audio: The camera will record audio along with video.

• Event Record Dwell: If linked recording is designated as an event-triggered action, recording takes place for the duration specied under this setting.

• Auto Deletion: Congure this option to delete recording data automatically after the specied number of days has elapsed. Select between 1 day and 999 day.

To disable Auto Deletion, select Never. If enabled, recording data will be stored on the NVR for the specied number of days and then deleted automatically. Expired recording data are deleted automatically at midnight and will be deleted even if the system reboots or the Auto Deletion setting has been changed.

• Limit Time-Lapse Recording: You can store event recording data for longer. If you do not wish to use Limit Time-Lapse Recording, select Never. This function is activated when data has been stored for longer than as congured because the recording disk has sucient capacity and saves new data by overwriting Time Lapse Recording data that are older than as specied under Recycle mode.

• If the recording stored on the disk is shorter than the duration specied under Limit Time-Lapse

Recording, the older of Event Recording or Time Recording data is deleted rst.

• The system's recording time may change depending on recording quality, resolution, motion, and other congurations made by the user. The duration specied under Limit Time-Lapse Recording may not be guaranteed in certain situations.

• Recording Failover Service: If the network goes down, this feature will transfer temporary data stored in the camera's buer to the NVR when the network goes online again.

• Use Panic Recording: Enable/disable Panic Recording.

• Panic Recording Duration: Disable Panic Recording automatically. Select between 5 mins and 1 hr. If you do not wish to disable the feature automatically, select No Limit.

• Video Prole: Select a recording prole value for

Panic Recording.

Page 45

Part 3 - Conguration

Schedule

Disabling Schedule On suspends schedule recording regardless of the schedule and displays the

icon on the upper left corner of each camera screen. Pressing the Panic button displays the

icon and commences

panic recording. Set Record Schedule mode as Simple Mode or

Advanced Mode. Advanced Mode allows you to congure a unique recording schedule for each event.

Select the

icon to delete a schedule.

• Changing the recording schedule mode suspends all active event-linked actions.

• Select the + button on the bottom left of the screen to add a schedule. Select Day to specify the Day setting or select All. Select Scope to specify the time frame.

Simple Mode Options

• Mode: Select No Record, Time, Event, or Time &

Event.

Record

Unless the Panic button is pressed, no recording will take place during the scheduled time frames on the scheduled days.

Time

The

icon appears on the upper

left corner of the screen. The

icon appears at scheduled times to indicate recording is in progress.

Event

The

icon appears on the upper

left corner of the screen. The

icon appears when the specied event occurs to indicate recording is in progress.

If Pre-Event is enabled, the and

icons appear when recording is not in progress, or the and icons appear when an event occurs and recording is in progress.

Time &

Event

The

icon appears on the upper left corner of the screen and recording commences as per the video prole selected for time under Setup. When an event occurs, the icon changes into (red) icon and recording commences as per the video prole selected for events under Setup.

• Channel: Select which cameras to apply the schedule to.

• Settings: Select to congure default recording prole values for Time Lapse and Event Recording modes.

Page 46

Part 3 - Conguration

Advanced Mode Options

Select to congure event types and video proles.

• Type: Event-specic and time recording icons are as follows:

Time Lapse

(Time)

Audio

Detection

Alarm-In

Trip Zone

Motion

Detection

Tampering

Video Loss

Text-In

Recording Fail

Fan Error

• Video Prole: Congure the prole to use for

recording.

• Dwell: Specify how long to record for after a

corresponding event occurs.

• Upper-tier schedule's settings apply to uncongured channels.

• If multiple events take place on a specic channel and dierent Video Prole and Dwell Time settings apply, highest settings apply to all event-linked recordings.

Pre-Event

When an event occurs, enabling this option includes the specied duration prior to the event in the eventtriggered recording.

• No.: Select which cameras to apply Pre-Event to.

• Video Prole: Select a video prole for the recording.

• Dwell: Specify the duration of pre-event recording data.

• If no event mode schedule exists in the schedule, a warning message prompting you to add an event mode schedule will be displayed.

• The warning message will appear even in Time & Event mode.

Page 47

Part 3 - Conguration

Event Setup

Refer to the Menu Use on page 36 for basic information on using the Setup menus.

Video-Analytics

Video-Analytics methods are Motion, Trip Zone, and Tampering.

Motion

• No.: Select which cameras to apply Motion Detection to.

• Sensitivity: Set daytime and nighttime sensitivity settings between 1 (Low) and 5 (High).

• Zone: Dene the motion detection block.

Use the remote control's arrow buttons to move the block selection window up, down, left, and right. The selection window consists of 8 blocks per row. Select/ deselect individual blocks using the Camera buttons. You can use the mouse to drag the zone and then select, clear, or reverse the selection.

From the zone selection screen, press the

button on the remote control or right-click on the mouse to open up the Zone Setup menu.

- Select: Conrm the block selection in the selection window.

- Clear: Clear the block selection in the selection window.

- Reverse: Clear the blocks selected within the selection window and select all unselected blocks within the selection window.

- Select All: Select all blocks.

- Clear All: Clear all block selections.

- Reverse All: Clear all selected blocks within the screen and select all unselected blocks within the screen.

- OK: Save the changes and exit the menu.

- Cancel: Exit the menu without saving the changes.

• Min. Blocks: Motion needs to be detected in more than the specied number of blocks in order to trigger a Motion Detection event. You may select a value between 1 and the number of blocks selected under Zone for daytime and nighttime, each.

Page 48

Part 3 - Conguration

• Actions: Specify which actions to take when motion is detected.

- Record: Specify which cameras to begin linked recording on when an event occurs. If the schedule is set to Event or Time & Event mode, the selected cameras will begin linked recording when an event occurs.

- Alarm-Out: Designate event-triggered alarm-out channels (each for the NVR and camera) and beeps.

- Notify: Congure to be notied of events by Mail, LAN1 through 5, SNS, and/or Alert Window.

- PTZ: Moves the PTZ camera to a specic preset position when an event occurs.

- Event Monitoring: Selects the cameras to monitor when an event occurs.

In order to use the Callback feature, the NVR must be registered on the remote program.

• Ignoring Interval: The system does not produce event log entries or issue remote notications regarding motion detected for the time specied after the initial motion was detected. Set the value between 1 sec and 5 secs or choose Never.

Ignoring Interval does not aect motion detection recording.

• Daytime Setup: Specify when daytime starts and ends. Adjust the time frame in 15-minute increments. Times outside the specied range will be assumed as nighttime by the system.

Trip Zone

• No.: Select which cameras to apply Trip Zone to.

• Sensitivity: Set daytime and nighttime sensitivity settings between 1 (Low) and 5 (High).

• Zone: Dene the motion detection block.

From the zone selection screen, press the

button on the remote control or right-click on the mouse to open up the Zone Setup menu.

Page 49

Part 3 - Conguration

- Select: Conrm the block selection in the selection window.

- Clear: Clear the block selection in the selection window.

- Reverse: Clear the blocks selected within the selection window and select all unselected blocks within the selection window.

- Select All: Select all blocks.

- Clear All: Clear all block selections.

- Reverse All: Clear all selected blocks within the screen and select all unselected blocks within the screen.

- Trip Direction: Dene in which direction the motion has to occur in order for it to be considered an event. Select In for movements from outside the selection area in or Out for movements from inside the selection area out.

- OK: Save the changes and exit the menu.

- Cancel: Exit the menu without saving the changes.

• Actions: Specify which actions to take when Trip Zone is detected.

- Alarm-Out: Designate event-triggered alarm-out channels (each for the NVR and camera) and beeps.

- Notify: Congure to be notied of events by Mail, LAN1 through 5, SNS, and/or Alert Window.

- PTZ: Moves the PTZ camera to a specic preset position when an event occurs.

- Event Monitoring: Selects the cameras to monitor when an event occurs.

In order to use the Callback feature, the NVR must be registered on the remote program.

• Trip Zone Ignoring Interval: The system does not produce event log entries or issues remote notications regarding Trip Zone events detected during the specied time following the initial Trip Zone event. Set a value between 1 sec and 5 secs or choose Never.

Trip Zone Ignoring Time does not aect Trip Zone recording.

• Daytime Setup: Specify when daytime starts and ends. Adjust the time frame in 15-minute increments. Times outside the specied range will be assumed as nighttime by the system.

Page 50

Part 3 - Conguration

Tampering

• No.: Select which cameras to apply Tampering to.

• Sensitivity: Set to between 1 (Low) and 5 (High).

• Activation Time: Specify how long tampering detection needs to last in order for it to be considered an event. Tampering detections that do not last for the specied duration of time will not be considered as events.

• Actions: Specify which actions to take when Tampering is detected.

- Alarm-Out: Designate event-triggered alarm-out channels (each for the NVR and camera) and beeps.

- Notify: Congure to be notied of events by Mail, LAN1 through 5, SNS, and/or Alert Window.

- PTZ: Moves the PTZ camera to a specic preset position when an event occurs.

- Event Monitoring: Selects the cameras to monitor when an event occurs.

In order to use the Callback feature, the NVR must be registered on the remote program.

• Use Ignoring Time: Select Time Setup to specify the tampering detection ignore time. Tampering detection will be disabled during the specied time frame.

Alarm-In

• No.: Enable / disable alarm-ins.

This option includes both local and network camera alarm-ins. 1 through 32 are network camera alarm-ins, whereas 33 through 48 are local alarm-ins.

• Title: Use the virtual keyboard to enter titles.

• Type: Change the alarm-in type.

• Actions: Specify which actions to take when Alarm-In is detected.

- Alarm-Out: Designate event-triggered alarm-out channels (each for the NVR and camera) and beeps.

- Notify: Congure to be notied of events by Mail, LAN1 through 5, SNS,

and/or Alert Window.

- PTZ: Moves the PTZ camera to a specic preset position when an event occurs.

- Event Monitoring: Selects the cameras to monitor when an event occurs.

• In order to use the Callback feature, the NVR must be registered on the remote program.

• Select Panic Record to specify which alarm-in channels to use. Panic Record commences when the corresponding alarm-in occurs and terminates when the alarm-in is deactivated.

Page 51

Part 3 - Conguration

Video Loss

• Actions: Specify which actions to take when a Video Loss event occurs.

- Alarm-Out: Designate event-triggered alarm-out channels (each for the NVR and camera) and beeps.

- Notify: Congure to be notied of events by Mail, LAN1 through 5, SNS, and/or Alert Window.

- PTZ: Moves the PTZ camera to a specic preset position when an event occurs.

- Event Monitoring: Selects the cameras to monitor when an event occurs.

In order to use the Callback feature, the NVR must be registered on the remote program.

• Ignoring Interval: The system does not produce event log entries or issue remote notications for video loss detected for the time specied after the initial video loss was detected. Set the value between

0.1 and 15 seconds or choose Never. This is supported only when video encoders are connected.

• Use Ignoring Time: Select Time Setup to specify the time to ignore video loss detection. Video loss detection will be disabled for a specied time period. This is supported only when video encoders are connected.

Audio Detection

• No.: Select which cameras to apply Audio Detection to.

• Sensitivity: Set to between 1 (Low) and 5 (High).

• Activation Time: Specify how long audio detection has to last in order for it to be considered an event. Audio detections that do not last for the specied duration of time will not be considered as events.

• Actions: Specify which actions to take when audio detection events occur.

- Alarm-Out: Designate event-triggered alarm-out channels (each for the NVR and camera) and beeps.

- Notify: Congure to be notied of events by Mail, LAN1 through 5, SNS, and/or Alert Window.

- PTZ: Moves the PTZ camera to a specic preset position when an event occurs.

- Event Monitoring: Selects the cameras to monitor when an event occurs.

In order to use the Callback feature, the NVR must be registered on the remote program.

• Ignoring Interval: The system does not produce event log entries or issues remote notications regarding audio detected during the specied time following the initial audio detection. Set a value between 1 sec and 5 secs or choose Never.

• Use Ignoring Time: Select Time Setup to specify the audio detection ignore time. Audio detection will be disabled during the specied time frame.

Page 52

Part 3 - Conguration

Recording Fail

• Actions: Specify which actions to take when a Recording Fail event occurs.

- Alarm-Out: Designate event-triggered alarm-out channels (each for the NVR and camera) and beeps.

- Notify: Congure to be notied of events by Mail, LAN1 through 5, SNS, and/or Alert Window.

- PTZ: Moves the PTZ camera to a specic preset position when an event occurs.

- Event Monitoring: Selects the cameras to monitor when an event occurs.

In order to use the Callback feature, the NVR must be registered on the remote program.

Text-In

• Setup: Congure text-in devices.

• It's possible to batch congure all text-in devices with the exception for port settings.

• An inux of large amounts of text-in data from multiple channels can hinder system performance.

• Text-In Product: The setup window is updated so that the portion below the port setting matches the corresponding text-in device. Displayed screenshot illustrates Generic Text settings.

• Transaction Start: Once Transaction Start has been designated, the system will recognize the specied string as the beginning of a transaction. You can choose the Any Character setting. Under this setting, any character will trigger the system into recognizing the start of a new transaction.

• Transaction End: Once Transaction End has been designated, the system will recognize the specied string as the end of a transaction. Select 0 more line(s) next to Transaction End and specify a value between 1 and 10. The system will recognize the specied Transaction End string plus the number of lines as being the end of a transaction.

Page 53

Part 3 - Conguration

• Line Delimiter: Designate a string to mark the end of a line. You can enter control strings by selecting and then entering ^, followed by a letter. For example, Carriage Return is ^M and Line Feed (new line) is ^J.

• Ignore String: Specify a string to ignore from transaction records.

• Case Sensitive: Ignores case in strings designated under Transaction Start, Transaction End, Line

Delimiter, and Ignore String.

Case Sensitive does not apply to control strings.

• Time Out: Once Time Out has been enabled, the system will assume the end of a transaction if no new string is entered within the specied duration of time. Select between 5 secs and 15 mins.

Selecting RS-232, RS-485, USB-Serial 1 through 8, or LAN 1 through 16 as the port activates the Port Setup button. Select Setup and congure the Baud Rate, Data Bit, Stop Bit, and Parity settings.

• If any one of LAN1 through 16 has been selected as the port, select the Port Setup button and congure the network port setting.

• If using a USB-serial port, the Text-In feature may malfunction if the USB cable is removed while the system is in operation.

• Title: Designate a name for the text-in device.

• Actions: Specify which actions to take when text-in is detected.

- Alarm-Out: Designate event-triggered alarm-out channels (each for the NVR and camera) and beeps.

- Notify: Congure to be notied of events by Mail, LAN1 through 5, SNS, and/or Alert Window.

- PTZ: Moves the PTZ camera to a specic preset position when an event occurs.

- Event Monitoring: Selects the cameras to monitor when an event occurs.

In order to use the Callback feature, the NVR must be registered on the remote program.

Camera System

The event occurs when the fan has stopped in the fan mounted camera.

• No.: Select which cameras to apply Fan Error to.

• Actions: Specify which actions to take when a Fan Error event occurs.

- Alarm-Out: Designate event-triggered alarm-out channels (each for the NVR and camera) and beeps.

- Notify: Congure to be notied of events by Mail, LAN1 through 5, SNS, and/or Alert Window.

- PTZ: Moves the PTZ camera to a specic preset position when an event occurs.

- Event Monitoring: Selects the cameras to monitor when an event occurs.

• In order to use the Callback feature, the NVR must be registered on the remote program.

• In case of the camera that not supports camera system event, the camera system feature will be disabled.

Page 54

Part 3 - Conguration

Network Setup

Refer to the Menu Use on page 36 for basic information on using the Setup menus.

General

• Remote Audio Channel: Transmits the selected channel's audio to the remote program. Select Select From Client to stream audio of the channel selected on the remote program.

Audio skipping and sync issues can occur under poor network conditions.

• Enable SSL for Transferring Data: Applies SSL (Secure Sockets Layer) protection on remote viewing and recording data transmissions.

• If using the SSL feature, it will not be possible to connect to the NVR from a remote program or a network keyboard that does not support SSL.

• Changing the SSL setting temporarily severs all remote connections to the NVR in order to apply the change.

• This product contains content developed by OpenSSL Project for use in Open SSL Toolkit (http:// www.openssl.org/).

• WebGuard: If you wish to use WebGuard, select WebGuard - Use WebGuard Service. Select WebGuard - WebGuard Port and choose a port number between 1024 and 65535. The port number can also be entered using the virtual keyboard. For more information on WebGuard, refer to the Part 5 - WebGuard on page 78.

• VNC: Use Virtual Network Computing (VNC) by clicking the Use VNC button to toggle between On and O. You will be able to change the settings if Use VNC is enabled. VNC service allows you to access the NVR and control it remotely using a PC or mobile devices via Ethernet.

- Port: Congure the port number of the VNC server.

- Password: Congure the Password to connect to the NVR from a remote locale.

Up to three users at a time can access a NVR remotely via VNC service.

• Network Bandwidth Limit: Congure the bandwidth limit.

If you congured Network Bandwidth Limit, the live video may not display smoothly in a remote program.

Key Function

← or h

Press the ← or h key to move to the left in the menu. This is the same as pressing the Left arrow button on the front panel.

→ or l

Press the → or i key to move to the right in the menu. This is the same as pressing the Right arrow buttons on the front panel.

↑ or k

Press the ↑or k key to move up in the menu. This is the same as pressing the Up arrow button on the front panel.

↓ or j

Press the ↓ or j key to move down in the menu. This is the same as pressing the Down arrow button on the front panel.

m or

Windows

Press the m or Windows key to display the Live Monitoring menu or Search menu on the screen. This is the same as pressing the MENU button on the front panel.

Enter or

Return

Press the Enter or Return key to select the highlighted item or complete an entry that you have made during system setup. This is the same as pressing the Play/Pause button on the front panel.

Page 55

Part 3 - Conguration

d or

PaceUP/

PageDown

Press the d or PageUp or PageDown key to toggle between dierent display formats. This is the same as pressing the DISPLAY button on the front panel.

c or Home

Press the c or Home key to copy video clips. This is the same as pressing the CLIP-COPY button on the front panel.

Press the F5 key to refresh the current VNC screen.

WAN

Designate the IP address type as Manual or DHCP.

Manual

• Set Typ e to Manual.

Manual lets you congure related settings manually. Congure IP Address, Gateway, and Subnet Mask settings manually using the remote control's arrow buttons.

• DNS Server: Enter the DNS server's IP address. The IP address can also be entered using the virtual keyboard.

• Remote Port: The port used by the remote program to connect to the NVR. Choose a value between 1024 and 65535. The port number can also be entered using the virtual keyboard.

• Remote Callback: Set the port number using for remote callback. The port number can also be entered using the virtual keyboard.

• Ping Test: Select to test the current WAN settings you made.

Enter the IP address of the NVR.

Adjust the frequency of the ping test.

Select Run to do the test. The test result is displayed.

Select Close to exit.

• If using a rewall, select Change Port to change the port number to one that is permitted by the rewall.

• Changing the port temporarily severs the NVR's remote connection.

Remote point IP and port settings on the remote program must also be changed in order for it to connect to the NVR.

• To use the UPnP (Universal Plug and Play) feature, select Use UPnP. If using an IP router (or NAT), UPnP service allows the device to automatically forward the port to the NVR.

• This port is used to access a port that has a private IP address.

• In order to use the UPnP service, the IP router (or NAT) must support UPnP port forwarding and have the relevant options enabled.

• Port number cannot be changed with Use UPnP selected.

• Status: Indicates the number of the port forwarded by the IP router (or NAT) to the NVR via UPnP service.

Page 56

Part 3 - Conguration

DHCP

Select DHCP and then Save to retrieve IP address and other network settings automatically from the DHCP server. Once the network settings have been retrieved, the NVR's current IP address is displayed in the IP Address eld.

• It may not be possible to retrieve the IP address if there is no DHCP server. If this is the case, contact your network administrator.

• With DHCP, the NVR's IP address might change with each startup.

There is a limit to the number of users allowed to connect remotely at the same time. Contact the service center for more information.

FEN

If using a dynamic IP address, FEN service makes it easy to connect to the NVR from a remote program without having to congure dynamic IP or router settings.

• Use FEN: Check if you wish to use FEN service.

• FEN Server: Enter the FEN server's IP address or domain name.

If you have congured the DNS Server setting under Network - WAN, you can enter the FEN server's domain name instead of its IP address in the FEN Server eld.

• Port: Specify the FEN server's port number.

If using an IP router (or NAT), port conguration and other network functions will depend on the usage method of the IP router (or NAT).

• FEN Name: After entering the NVR name you wish to register on the FEN server, check and register the entered name. This is a unique NVR name that will be registered on the FEN server.

• You will not be able to save FEN settings unless you click on the Check button next to the NVR Name eld and check the entered name's availability.

• You will be prompted with an error message if you do not enter NVR name or enter a name already registered to the FEN Server.

• If the device name contains the #, \, and/or % symbol, it might not be able to connect to the NVR from the WebGuard program.

• Status: Used to check the status of the device being registered to the FEN server.

Select Save after making changes to register the NVR's name to the FEN server.

If FEN has been congured correctly, the FEN server's help desk information will be displayed in the Help Desk eld the next time you access the FEN Setup screen.

Page 57

Part 3 - Conguration

Device Setup

Refer to the Menu Use on page 36 Menu Use on page 36 for basic information on using the Setup

menus.

Alarm-Out

Select the + icon at the bottom left corner of the screen to add a schedule.

You can apply dierent schedules for dierent Days of the week.

Select

to delete the schedule.

• Dwell Time: Select a value between 5 secs and 15 mins as the alarm-out duration.

• Title: Designate a name for the alarm-out.

• Range: Change the schedule time frame.

• Mode: Select Event, On, or O.

Event

Generates an alarm-out when an event occurs.

On Alarm-out is always on.

O

Alarm-out is always o.

• Channels: Congure alarm-out port and beep settings.

Remote Control

• Port: Select None, or RS232. Click the Setup button and then select the correct Baud Rate, Parity, Data Bits and Stop Bits for the device you are connecting to the NVR. You can select the device from the Remote Control Product list. If the RS232 port and RS485 port are in use for PTZ control, networking or text input, the remote keyboard cannot be congured. A warning message window will appear when other devices are using the same port, such as PTZ control, networking or text input. The message warns that you cannot use another device because the ports overlap.

Display Setup

Refer to the Menu Use on page 36 for basic information on using the Setup menus.

OSD

Show OSD (On Screen Display) information on the bottom of the screen.

Page 58

Part 3 - Conguration

Status

• Date and Time: Displays the date and time.

• Remote Control: Displays remote control receptivity.

• Free Space: Displays whether or not the NVR is in the recycle mode, and displays the available storage space when not in the recycle mode.

• User Name: Displays the current user logged in.

• Background Panel: Displays background panel at the bottom of the screen in black.

Camera

• No.: Displays the camera number on the upper left corner of the camera screen.

• Title: Displays the camera name on the upper left corner of the camera screen.

• Record: Displays recording and schedule icons.

• Audio: Displays the

icon on channels generating

audio.

• PTZ: Displays the

icon on PTZ cameras.

• PTZ Zoom: Displays the zoom magnication (e.g. x2, x3, etc.)

• Resolution (Search): Displays the recording resolution in Playback mode.

• Text-In: Displays strings received from text-in devices. Select Display Dwell and specify how long to display the text-in string. Text-in strings are shown on the single screen only.

• Zoom: Displays a zoomed in state.

• Network: Displays the icon when the unit is connected to a network via Ethernet.

• Freeze & Sequence: Displays freeze and sequence icons.

• Screen Group: Displays the current screen's group.

Main Monitor

Congure monitor-related settings.

• Mode: Select Full Sequence or Cameo Sequence.

• Interval: Select between 3 secs and 2 mins. For more information on Sequence, refer to the 6 Sequence on page 29.

• Resolution: Select 1920 x 1200, 1920 x 1080, 1680 x 1050, 1600 x 1200.

• Supported resolutions may be restricted depending on the monitor.

• We recommend that you use 1920 x 1080 resolution.

• Manual Conguration: Set the resolution manually regardless of the resolution supported by the monitor.

• Event Monitoring On: With Event Monitoring enabled, video feed from the camera congured to start recording when an event occurs is shown on the screen. For more information on Event Monitoring, refer to the Event Monitoring on page 33.

Page 59

Part 3 - Conguration

Notication Setup

Schedule

Select the + icon at the lower left corner of the screen to add a notication schedule.

• Day: Add dierent schedules for dierent days of the week.

• Range: Change the event notication time frame.

• Notify: Select which notications to generate when an event occurs. Select Mail, LAN 1 through 5, SNS, and/or Summary.

• In order to use the Notication (Callback) feature, the NVR must be registered on the remote program.

• Select the

icon to delete the existing schedule.

• Summary Email Interval: Transmit event summary emails to a remote destination at specied intervals.

Callback

Congure Callback settings.

Enter the IP address of the receiving server and set

Retry to between 1 and 10 in case of connection failure.

Mail

Congure Mail settings.

Select the + icon at the bottom left corner of the screen to add a mail account.

Select Recipient and then enter the mail address and server information.

The recipient's mail address must be in the correct email format and contain the @ symbol.

Select the icon to attach event recordings to outgoing mails.

Select the

icon to delete the account.

Select MP4 Clip to attach event recordings to outgoing mails.

Page 60

Part 3 - Conguration

The event recordings generated by a camera can be attached only. Select the MP4 Clip option at the bottom to attach .mp4 video clips.

SMTP Setup

Select SMTP Setup at the bottom right corner of the screen to congure an SMTP server.

Select the SMTP server Type.

Enter the SMTP Server's IP address or domain name and then congure the Port and Sender settings.

Default SMTP server port number is 25. Select Test to send out a test mail using the current settings. Select Use SSL/TLS to use an SMTP server that requires SSL connections.

• If you have congured the DNS Server setting under Network - WAN, you can enter the STMP server's domain name instead of its IP address in the SMTP Server eld.

• Address entered under Sender must be in the correct email format and include the @ symbol.

If user authentication is required by the SMTP server, select Use and then enter the User and Password information.

Select OK to apply and exit.

This product contains content developed by OpenSSL Project for use in Open SSL Toolkit (http://www. openssl.org/).

SNS

This option enables the NVR to send out SNS messages.

The SNS (Social Network Service) feature sends out event-related messages to designated Twitter accounts. Select the + icon at the bottom left corner of the screen to add an SNS account. Select the

icon on the right

side of the list to remove the SNS account. Enter the User Name and Password information.

Messages may not be transmitted successfully due to limitations in Twitter's services.

Page 61

Part 3 - Conguration

Camera Setup

Refer to the Menu Use on page 36 for basic information on using the Setup menus.

Registration

You can register cameras at remote locales. By selecting a number from the list, you can move the camera up or down the list using the mouse wheel to reorder its position. The remaining cameras will move down the list automatically.

• Title: Edit the camera’s name.

• MAC Address: Displays the camera’s MAC address registered to the NVR.

• Address: Displays the camera’s IP address registered to the NVR.

• Model: Indicates the camera’s model.

• Scan: Select to scan and register the device connected to the NVR.

This feature is supported only when connected to the NVR from a remote program.

Device Scan

Scan the device under Registration - Scan.

• Protocol: Select the protocol you wish to search for that was used by the camera (or encoder).

• Even if the network device uses a protocol supported by the NVR, the device itself may not be visible for scanning and registration by the NVR. For more information about supported network devices and models, contact your retailer.

• The supported scan modes may vary depending on protocol selected.

• Mode: Select the scan mode.

– Auto Scan(LAN): Lists any cameras in a LAN

environment. If Auto scan (LAN) fails to recognize the camera, try using IP Address scan instead.

– IP Address: Enter the IP address of a camera.

The NVR scans for the camera that matches the specied address. If you enter an IP address range, the NVR scans for cameras falling under the specied address range. By specifying an IP address, you can also specify which port to use with the Remote Admin feature. It is recommended that you do not network the camera via DHCP (Dynamic Host Conguration Protocol). If the camera is networked via DHCP, the camera may not be connected properly depending on changes in the external network environment.

If Auto Scan (LAN) fails to recognize a camera, try using the IP Address scan instead.

• Filter: Enter a keyword in the MAC Address / Address / Model / Name / Status elds for the selected camera. This allows the user to scan this camera easily.

When conguring a port, the device may fail to scan if the port selected for the NVR and the port selected for the camera dier. In this case, you must register the camera to change its IP address.

Page 62

Part 3 - Conguration

• No.: Select the registered camera number and click the Add Camera button to register the camera.

• MAC Address: Displays the scanned camera’s MAC address.

• Address: Displays the scanned camera’s IP address.

• Model: Indicates the camera model.

• Protocol: Indicates the scanned camera’s protocol.

• Name: Displays the scanned camera’s IP name.

• Status: The “Registered” indicates the camera is registered to the NVR and “Not registered” indicates the camera is not registered to the NVR.

If the password is set or you want to register the third party cameras, registering a device requires an authorized user login.

Select the desired device from the list and click the Add Camera button, then the login window will appear.

Select a user, enter the password, and then select OK.

• By selecting Apply to All Devices, you can apply the same authentication information to all of the network devices in the list.

• When you select multiple network devices from the list and click the Add camera button, a window for the network device will appear. Select Skip to skip the authentication settings for the current network device and to display the Authentication window of the next network device.

General

Enable/disable the covert view and rename cameras.

• Title: Edit the camera's name.

• Use: Set the camera as Normal, Covert 1, or Covert 2.

Live images and video recordings from cameras that have been set as Covert 1 or Covert 2 will not be available to users who do not have covert camera access. Setting a camera as Covert 1 hides its images but does display OSD information about the camera. Setting a camera as Covert 2 hides its images as well as ODS information about the camera as if it has been deactivated completely.

Page 63

Part 3 - Conguration

Advanced Setup

Congure security and other advanced camera settings.

• Video: Adjust the camera image sensor settings such as white balance and exposure. Conguration options may dier depending on the camera model.

• Privacy Masking: Enable/disable and congure privacy masking for the camera.

• SSL: Set the camera's security level as Unavailable,

Standard, High, or Very High. Standard, High and Very High settings apply SSL (Secure Sockets Layer)

protection to the camera.

• Mode: Select a resolution mode. It is supported by video encoders or analog cameras only.

• PTZ: If using RS-485-compliant camera, congure it for use in PTZ Mode.

– PTZ Product: Choose to select the model of

installed PTZ device. – ID: Choose to assign an ID to each PTZ device. – Choose to set up Baud Rate, Data Bit, Stop Bit

and Parity of the connected device.

Refer to the PTZ device manufacturer’s instructions for the proper settings.

Types of conguration options shown vary depending on the PTZ functions supported by the camera.

2 3 4

7 8 9

Numbers shown below Preset, Scan, Pattern, and Tour indicate the numbers of congured functions.

1 Preset

• Use the buttons below to choose a preset position.

- Directional Buttons (

Used to tilt and pan the camera.

- Zoom (

): Zoom in and out.

- Focus (

): Adjust camera focus to far or

near.

- Speed: Specify the camera's panning and tilting speed.

Page 64

Part 3 - Conguration

• Set: Choose a preset number and then enter a name. This saves the current preset under the specied preset number and name.

• Go to: Select a preset from the list and then click Go to to move the camera to the selected preset position.

• Edit: Used to change the selected preset's name.

• Remove: Used to remove the selected preset.

2 Scan Used to set up a prole for moving the camera

between two points. At least two presets must be available in order to use the scan feature.

• Set: Used to set up a scan prole.

- Name: Enter a name for the scan prole.

- Start/Stop: Specify which presets to use as start and stop points.

- Dwell Time (sec.): Specify how long the camera will dwell at start and stop positions.

- Speed/Direction: Specify scanning speed and direction.

• Test: Select a scan prole and then click Test to test it.

• Edit: Used to edit the selected scan prole.

• Remove: Used to remove the selected scan prole.

3 Pattern Used to set up a pattern prole for the camera to

follow along.

• Start recording: Select a pattern number, enter a name for the pattern, and then click OK to save the pattern. Move the camera using directional, zoom, and focus buttons and then click Stop recording to save the pattern prole. You can record up to two minutes of movement.

- Directional Buttons (

Used to tilt and pan the camera.

- Zoom (

): Zoom in and out.

- Focus (

): Adjust camera focus to far or

near.

- Speed: Specify the camera's panning and tilting speed.

• Test: Select a pattern prole and then click Test to test it.

• Edit: Used to edit the selected pattern prole.

• Remove: Used to remove the selected pattern prole.

4 Tour Used to set up a tour prole of multiple functions in

a designated sequence.

Page 65

Part 3 - Conguration

• Set: Used to set up a tour prole.

- Name: Enter a name for the tour prole.

- No.: Indicates the order of the function in the tour sequence.

- Dwell Time (sec.): Specify how long to perform the selected function for.

- Speed: Specify the preset speed.

• Test: Select a tour prole and then click Test to test it.

• Edit: Used to edit the selected tour prole.

• Remove: Used to remove the selected tour prole.

Select Apply after setting up a preset, scan, pattern, or tour prole to see images from the concerned camera on the left side of the screen. Selecting Apply or OK displays a popup screen that indicates whether the prole has been set up successfully.

5 PTZ Reset: Reboots the camera’s panning / tilting

and zoom settings.

6 Home Position: Specify the camera's home

position.

• Default: Uses the factory-default position as the camera's home position.

• Custom: Uses the user-dened position as the home position.

• Select Set to change the home position.

7 Auto Run: Specify which action to take if the

camera has not been controlled for the specied duration of time.

8 Auto Pan: Specify the camera's panning

direction. When Auto Pan is selected from a remote program, the camera pans in the direction selected here.

9 Auto Flip: Automatically ips the image when

the camera tilts past 90° to prevent the objects from appearing upside down.

• Digital: Flips the image left to right or top to bottom.

• Mechanical: Automatically pans or tilts the camera.

• O: Disables Auto Flip.

0 Tilt-Range: Specify the camera's tilting range.

! Restore: Specify whether to restore the camera

to its last position or function. Enabling this option restores the camera to its last position or function after being restarted.

Privacy Masking Options

Select Name to rename the privacy masking area. Select the

icon to delete the existing privacy masking area. Select Privacy Masking Setup to display additional privacy masking area options. You can drag on the area with the mouse to resize it or add up to 16 dierent areas.

• Edit: Rename the selected privacy masking area.

• Delete: Delete the selected privacy masking area.

• Save: Save the changes and exit the privacy masking area options screen.

• Cancel: Exit the privacy masking area options screen without saving the changes.

Page 66

Part 3 - Conguration

Image Sensor Options

• Product, Firmware Version: Displays the camera model name and rmware version.

• Video Style: Select TV Color or PC Color.

• Backlight Compensation: Enable/disable Backlight Compensation. If enabled, objects are exposed brighter in backlit situations.

• Sharpness: Adjust the sharpness level. Adjust the contours to make the images look sharper. Increasing the value raises the sharpness level, but using too high a value can result in unwanted noise.

• Noise Filter: Select the noise lter level. Noise lter can reduce the noise in images taken under lowlighting conditions. Increasing the value reduces the noise, but using too high a value can result in blurry images.

• 3DNR : Enable/disable 3DNR (3D Noise Removal). 3DNR reduces background noise in images taken under low-lighting conditions. 3DNR does not produce blurry images like Noise Filter but can result in ghosting.

• IR Mode: IR Mode blocks out the infrared spectrum. You can ensure clear images at all times by blocking out the infrared spectrum in high-lighting conditions and allowing the infrared spectrum to pass through in low-lighting conditions.

– Daytime Mode/Nighttime Mode: Enable/disable

IR Mode.

– Auto: Allow the system to enable/disable IR Mode

automatically.

– Schedule: Set up the IR Mode schedule. IR

Mode is disabled for all days and times that are designated as Daytime in the schedule and is enabled at all other times.

• White LED Mode: Clicking on/o enables or disables White LED lighting when motion is

detected by the PIR sensor. Also clicking auto allows the system to enable/disable White LED mode automatically.

• Black & White Mode: Display the images in greyscale for greater clarity in low-lighting conditions.

– On/O: Enable/disable Black & White Mode. – Auto: Allow the system to enable/disable Black &

White Mode automatically.

– Schedule: Set up the Black & White Mode

schedule. Black & White Mode is disabled for all days and times that are designated as Daytime in the schedule and is enabled at all other times.

• Smart IR: Adjust the IR LED's brightness level. Select On to allow the system to adjust the brightness level automatically. Deselect On to select a brightness level manually between 0% (darkest) and 100% (brightest).

• Advanced AE Mode: Select desired setup mode between Normal and Number-Identication. In Number-Identication mode, when a certain area of images is too bright due to backlight under low lighting conditions and it causes the other area to be too dark, this function provides the other area of images brightly and clearly by blocking the backlight in the certain area. Dark parking lot entrances and gas station entrances at night, for example (Local Exposure compensates for the bright light coming from incoming vehicle headlights and makes it possible to see the license plates). When setting to the Number-Identication mode, some option settings will be adjusted automatically, and you cannot change them as long as the Setup Mode is not changed.

• Switching Level: Controls the changing time of daytime / nighttime mode, depending on the Switching Level between 1 to 10. The higher the value is, day / nighttime mode is changed under high-lighting conditions. Also the lower the value is, day / nighttime mode is changed under low-lighting conditions.

• Mirror: Select Horizontal or Vertical to ip the image horizontally and/or vertically.

Select Apply after setting up a camera to see images from the concerned camera on the left side of the screen. Selecting Apply or OK displays a popup screen that indicates whether the camera has been set up successfully or not.

Page 67

Part 3 - Conguration

White Balance Options

• Preset: Use precongured white balance settings.

- Auto: Allow the system to adjust the white balance automatically. The system will assess the lighting conditions and adjust the white balance automatically.

- Incandescent - Fluorescent Cold: Select a lighting type to apply the appropriate white balance.

• Manual: Adjust the white balance manually. Adjust Red and Blue gain values. Greater the value, greater the intensity of the corresponding color.

Exposure Options

• AE Target Gain: Specify exposure compensation's target gain. Exposure is compensated automatically based on the specied target gain. Higher the gain, brighter the images.

• Local Exposure: Activate Local Exposure. Use Local Exposure on images that appear too dark due to backlighting conditions and on images containing over-exposed sections. Greater the value, clearer the image. e.g.) Dark parking lot entrances and gas station entrances at night (Local Exposure compensates for the bright light coming from incoming vehicle headlights and makes it possible to see the license plates).

• Anti-Flicker: If the lights in the area where the camera is located use alternating current, specify the frequency of the lights to minimize ickering. Matching the frequencies can eliminate ickering completely. (NTSC: 60Hz, PAL: 50Hz).

• Slow Shutter: Activate Slow Shutter. The slow shutter mode functions only under low lighting conditions. When the slow shutter mode is enabled, images are displayed bright even under the low-lighting conditions. There may be a dierence in the way it functions depending on the camera model. See the camera user's manual for details.

• Focus Mode: Used to change the focus movement format as Auto/Manual/Semi-Automatic. It may not be supported depending on the device.

• WDR: Disables or enables the WDR (Wide Dynamic Range). When the very dark and very bright areas exist simultaneously on the screen, WDR allows you to recognize the both areas.

• DC IRIS: Select the lens IRIS type. If a manual IRIS lens is mounted on the camera, select Manual. If a DCtype auto IRIS lens is mounted, select DC IRIS.

Page 68

Part 3 - Conguration

• Shutter Speed Control: Adjust Shutter Speed. This option is available only when Anti-Flicker and Slow Shutter are both set to O.

- Auto: The system will assess the lighting conditions and adjust the shutter speed automatically.

- Manual: Use the slider to select the desired shutter speed. Select the most suitable minimum and maximum shutter speeds for the lighting conditions in the area where the camera is located. (1/30 to 1/8000)

Miscellaneous

• Image Stabilizer: Activate Image Stabilizer. The Image Stabilizer reduces blurring caused by camera shake that results from external conditions such as the wind.

Stream

Congure the camera's live and recording resolution, picture quality and ips speed settings.

• Camera Channels: It's possible to congure a unique stream for each camera.

•

: Apply the stream settings of the camera

selected under Camera Channel to a dierent camera.

• Stream: Congure Stream 1, Stream 2, or Stream 3.

- Resolution: Select a resolution supported by the camera. Maximum available resolution is chosen automatically based on the selected streams.

- Quality: Select Very High, High, Standard, or Basic. You can assign dierent Quality settings to dierent cameras.

- ips: Select a value between 1 and 30. Maximum ips is determined automatically based on the selected the stream.

• Live Video Prole: Check the current Live streams. It allows you to select the streams according to split screen.

• Record Video Prole: Display 3 record video prole.

• Remote Video Prole: Set up the remote streams.

- Dynamic Stream: Automatically transmits the Stream 1, Stream 2, or Stream 3, depending on

the remote program’s live screen layout.

Page 69

Part 3 - Conguration

Audio

Congure audio recording settings for all cameras simultaneously.

• Audio Codec: Select an audio codec. (G.711 u-Law, G.711 a-Law or G.726)

• Audio In: Select an audio input source (microphone or line-in) and then adjust the volume.

• Audio Out: Adjust the volume.

• Associated Audio In: Associates the selected audio channel with the camera. It is supported by analog cameras only.

Cameras do not feature built-in audio amplier units and therefore require the user to purchase a speaker system with a built-in amplier separately.

Upgrade

Select Firmware Upgrade to display the USB search window.

Select the corresponding upgrade package from the storage device connected to the NVR's USB port.

After selecting an upgrade package, select Apply to upgrade the camera.

• If an upgrade attempt fails, an upgrade failure message will be displayed. Refer to Error Code Types on page 84 for more details.

• The camera will reboot after the upgrade and then reconnect automatically.

• Current software version is not checked when upgrading a network camera.

Page 70

Time-Lapse Search

While in Live mode, select the Search Mode icon and select Time-Lapse Search or Event Log Search.

Select MENU button on the remote control while in Search mode to display a menu from which you can select Control Area.

Press MENU button once more to move the Control Area.

In 2 seconds after moving the Control Area, the Control Area becomes selected and the corresponding menu disappears.

After selecting the desired Control Area, use the Arrow buttons on the remote control to select the menus and options. Search menu can also be displayed by placing the mouse cursor on the upper portion of the screen.

The Control Area consists of Menu, Screen, Record Table Search, and Playback.

1 Menu: Activates side Search menu. Use the arrow buttons to select an option. 2 Screen: Activates the middle screen section. Use the arrow buttons to select a camera. 3 Record Table Search: Activates the bottom record table. Use the arrow buttons to select a record table.

Part 4 - Search

Page 71

Part 4 - Search

Search Menu

1 Layout

Used to change the screen layout to single screen, 2x2, 1p5, 1p7, 3x3, 4x4, 5x5, or 6x6.

2 Display

• OSD On/O: Enables/disables the OSD feature.

• Aspect Ratio: Select whether to enable the original aspect ratio of video transmitted from the camera.

3 Previous/Next Group

Loads the previous/next screen group. (in single screen only)

4 Search Mode

Search by changing Time-Lapse Search and Event Log Search.

5 Live Mode

Activates Live mode.

6 G o To

Search video recordings based on date and time. Specify the date and time and then select Go to jump to the corresponding video recording. Select a

(bookmark) button on the

right side to move to the saved bookmark position.

7 Select Camera

Select a camera channel and display it as a single screen.

8 Zoom

Zoom in.

9 Panic Recording

Use the Panic Record feature.

0 Alarm

Pressing this button while the alarm has been activated resets all NVR alarm outputs, including the built-in buzzer.

! Database

• Record: Search recording data contained in the main recording device.

• Other: Search data recorded while disks used in other systems were connected.

@ Print

Print the current image.

Page 72

Part 4 - Search

Time-Lapse Search Menu

1 Record Table

Display the current channel's recording information.

Recording date and time are shown on the top of the search window. The grey indicator line on Record Table indicates the current playback position. Use the arrow buttons on the remote control to move the current playback position in units of individual sectors. Alternatively, use the mouse to jump to the desired playback position.

• Farther back the data is on the record table, the more recent it is.

• If the system's clock is changed to a previous date and time, it is possible for multiple recordings with the identical time stamp to exist. Overlapped segments are highlighted in yellow.

Selecting or on the bottom left portion of the Time-Lapse search window changes the size of search window and displays all or minimum channels. Using the scroll, the information of other channels

which is not shown can be checked in the minimum size of Time-Lapse search window. Select

(zoom-in) to compose recording data

in 1-minute segments and select

(zoom-out) to compose recording data in 3-minute segments. Selecting zoom-out displays more time in one screen than zoom-in screen.

If recording from points in time prior or after the time frame displayed on the screen is available, scroll appear on both ends of the date and time information line. Scroll using the arrow buttons on the remote control or by dragging with the mouse to check recording data.

Display the latest update recording information when selecting

(Refresh).

547

613

Page 73

Part 4 - Search

Recording Data Bar Colors

Blue Time Lapse Recording

Purple Event Recording

Yellow Pre-Event Recording

Red Panic Recording

Green

Faulty recording due to a temporary disruption in device connection.

2 Playback Controls

Play and scan through video recordings. Playback controls have the same functions as their remote control counterparts.

• Jog Shuttle

Adjust the playback method and speed. Jog shuttle's vertical indicator indicates the current

playback direction and speed. Vertical indicator placement to the right of the center means the video is being played back in the forward direction. Placement to the left means the opposite. Farther away the vertical indicator from the center, faster the playback speed. Click and drag the vertical indicator to adjust the playback speed. Releasing the mouse button returns the vertical indicator to the center and stops video playback.

3 Bookmark

Select Add Current Position to add a bookmark to the current playback position. Select Title and enter the name of the registered bookmark.

The maximum number of bookmarks that can be saved is 12.

Select a bookmark from the Bookmarks window to move to the registered playback position.

Select Bookmark list and then the icon to delete the corresponding bookmark.

4 Calendar Search

Use the calendar to search for video recordings by specic dates.

Dates containing video recordings are highlighted in light grey. Selecting a date containing video recording data loads the earliest recording from that date (paused state). Selected date is highlighted in black of grey background.

5 Clip-Copy

• A-B Clip-Copy

Designate a start point and an end point and copy the data in between. The Clip-Copy Setup window will appear. Select A and B points are automatically applied as From and To values.

• Clip-Copy

Open up the Clip-Copy Setup window. Specify the

From and To settings. Pressing the remote control’s CLIP COPY button while in Live or Playback mode will

also open the Clip-Copy setup window.

• Channels: Specify which channel to save the

Page 74

Part 4 - Search

recording to.

• Password: Enable password protection for the saved video clip and assign a password.

• Dest.: Select which storage media to use.

• File name: Designate a name for the le. The name may be up to 63 characters in length.

Special characters such as \, /, :, ;, *, ?, !, “, <, >, and | are not permitted.

• Include Text-In Data: Enabling this option will save the video clip along with any available text-in data.

• Use Site Info: Adds Site info to the Clip Copy le's name.

Special characters contained in the location info (such as \, /, :, ;, *, ?, !, “, <, >, and |) will be replaced with _ when the information is added to the le name.

Selecting Start displays a calculation on the size of the data to be copied. Check the calculation and then select Continue to proceed. While Clip Copy is in progress, you can select Cancel to cancel the process or select Close to allow the window to run in the background. Selecting Close does not cancel Clip Copy. Once the process is complete, you will be prompted with a conrmation window.

• One-Touch Clip Copy congures the storage range automatically based on the storage drive's capacity. If there is insucient space available on the selected storage device, you will only be able to Clip Copy an amount of data equaling the remaining space available on the storage device.

• The NVR displays the volume as 30GB regardless of the actual disk volume and the maximum size limit on Clip Copy les is 30GB.

• Saving a segment that is more than 2GB in size produces multiple les that are up to 2GB in size, each.

• Clip Copy les can be played back on Windows systems. For more information, refer to the REVO Remote Pro operation manual.

• For USB ash memory devices, the NVR supports the FAT32 le format only.

Do not disconnect the USB cable or power o the USB device while USB Clip Copy is in progress. Doing so can cause the NVR to malfunction or critically damage the external USB device's le system. You may be prompted with an error message when trying to back up on the device. If so, you will need to restart the NVR. If the USB hard disk's le system has been damaged, restarting the NVR will not solve the problem and the aforementioned error message will continue to be displayed each time you attempt a backup. If this is the case, you will need to format the HDD or use a recovery program to repair the damage to the drive's le system.

6 Motion Search (This function supports only in single screen.) Motion Search cannot be performed while using a split

screen layout. Select Single Screen mode.

• Select First under From and Last under To to search the recording from start to nish. Alternatively, you can uncheck the First and Last options and specify the search time frame manually.

• Type: Motion Search looks for motion in the selected area by comparing individual frames against their preceding frames. This means slow and gradual movements, no matter how long they persist, will not be recognized. In contrast, Museum Search looks for changes in the specied area by using the From frame as a reference. Museum Search, therefore, recognizes even minute deviations from the original From frame.

• The Zone setting can be congured in the identical manner as the Zone setting under System Setup Motion Detection. For more information, refer to the

Motion on page 47.

Museum Search may not function properly if the

edge of the object is included in the Zone. For more accurate search results, set the inside of the object's edge as the detection zone.

• Sensitivity: Set to between 1 (Low) and 5 (High).

Page 75

Part 4 - Search

• Min. Blocks: The Min. Blocks option is available with Motion Search only.

Once all the options have been congured, select Search. Select search results entry to display the video recording on the left. To play the recording, exit the setup window by selecting Close.

7 Text-In Search

Perform Text-In Search.

Select a Transaction to display the video recording that corresponds to the selected time and date (paused state).

Text-in information is superimposed on the screen at normal playback speed. The information is not shown under any other playback speed.

Select Option... to congure Text-In Search options.

• Select First under From and Last under To to search the recording from start to nish. Alternatively, you can uncheck the First and Last options and specify the search time frame manually.

• Channels: Select a channel.

• Select Text-In Device to select a device type.

• + Button: Add a search variable.

• Case Sensitive: Congure case sensitivity.

• Load: Retrieve stored search option settings.

• Save: Save the current search option settings.

Once all the options have been congured, select

Search to begin the search and return to the Text-In Search setup window.

8 Slow Play Option

Search the playback screen at low speeds. Select the desired playback speed (x1/2, x1/3, x1/4, x1/6, x1/8) and then select Play.

Context Menu

Select the Menu button or right-click on the Camera screen to access the context menu.

• Zoom: Zoom in.

• Audio: Enable/disable audio. Audio playback of the selected camera is available in full screen mode only.

• Show/Hide Text-In: Show/hide text-in information contained in the recording.

• Edit Group: Rearrange the split screen layout.

Print the current image. While in Search Mode, select Pause to pause playback.

Select Print from the Search menu to open up the Print Setup window.

• Printer Model

- File Printer: Saves the current frame to the USB storage device as a .pdf le that can be printed on the printer connected to a computer.

• Paper Size: Select the desired paper size.

• File name: Designate a name for the le.

Page 76

Part 4 - Search

Event Log Search

Select Search Mode > Event Log Search to bring up the Event Log Search window.

• Select an event to display the recording made on the selected time and date (paused state). Select the Play button in the middle of the screen to start playing back the recording. Use the drop-down menu above to load recordings from other cameras.

• You can uncheck the First and Last options at the top of the Event Log Search window and specify the search time frame manually.

Select First for From and Last for To to select the entire recording from start to end.

• If designating From or To settings manually, you will be able to enable/disable the Check Time Overlap option.

If the system's clock has been changed and the designated From or To point exists at more than one location, you will have to choose one. Only the events that took place between the selected From and To points will be searched. If Check Time Overlap has not been selected, events from the entire From and To range will be searched.

Use event lters to include/exclude specic system events such as Panic Record, Check Recording,

Check Alarm-In, Disk Almost Full, Disk Bad, Disk Temperature, Disk S.M.A.R.T., Fan Error, eSATA Disconnected and Disk Cong Change from the

search.

Camera Filter

• Alarm-In: Select which channels to search alarm-in events in.

• Motion: Select which channels to search motion detection events in.

• Video Loss: Select which channels to search video loss events in.

• Audio Detection: Select which channels to search audio detection events in.

• Trip Zone: Select which channels to search trip zone events in.

• Tampering: Select which channels to search tampering events in.

• Text-In: Select which channels to search text-in events in.

• Record Channel: Select which record channels to search events in.

• Recording Fail: Select which channels to search recording fail events in.

• Fan Error: Select which channels to search fan error events.

Selected record channels are searched for events with at least one linked recording. If no camera is selected, only the events with no linked recording camera are searched.

Page 77

Part 4 - Search

Overlapped Recording Search

If the system's clock is changed to a point in the past, overlapping recordings may be produced. Overlapped recordings have to be searched in segments.

For example, making a recording from 1 o'clock to 5 o'clock, changing the system's clock at 5 o'clock to 3 o'clock, and then continuing to record until 6 o'clock produces two recordings that overlap between 3 o'clock and 5 o'clock. This results in two segments for the period between 3 and 5.

1:00 2:00 3:00 4:00 5:00

3:00 4:00 5:00 6:00

Segment 1

Segment 2

When searching overlapped video recordings, you can choose a specic point in time or a time frame. If you use the Go to the Date/Time option and select a point within the overlapped time period (4 o'clock, for example), you must specify 4 o'clock in which of the two existing segments.

If you use the Event Log Search or Motion Detection option and select a time frame within the overlapped time period (4 o'clock to 5 o'clock, for example), you must choose between the two redundant sets of From and To values. Selectable search ranges are as follows:

• 4 o'clock in segment 1 to 5 o'clock in segment 1

• 4 o'clock in segment 1 to 5 o'clock in segment 2

• 4 o'clock in segment 2 to 5 o'clock in segment 2

Page 78

WebGuard is a program that allows you to view and search video from remote locations over the Internet and can be accessed on a regular web browser such as Internet Explorer.

System requirements for running WebGuard are as follows:

• OS: Microsoft

Windows® XP (Service Pack 3), Microsoft® Windows® Vista (Service Pack 1), Microsoft® Windows® 7

(Home Premium, Professional, Ultimate) or Microsoft

Windows® 8 (Pro, Enterprise)

• CPU: Intel Pentium IV 2.4GHz or above (Core 2 Duo E4600 recommended)

• RAM: 1GB or more

• VGA: 128MB or more (1280x1024, 24bpp or above)

• Internet Explorer: Ver. 7.0 or above (32-Bit)

• WebGuard only works with Microsoft Internet Explorer and will NOT work with other browsers.

• WebGuard does not work in Microsoft

Windows® 8 metro UI.

Launch Internet Explorer and then enter the following information in the address bar.

– http://IP Address:Port Number (NVR system's IP address and WebGuard port number congured under Network

> General (Default Value: 12088))

– http://FEN server address/FEN Name (FEN Name: NVR name congured on the FEN server)

– http:/www.dvronline.net (will be prompted to enter NVR's IP address or FEN name registered to the FEN server

upon login)

Contact your network administrator for the IP address of the NVR you wish to connect to and the WebGuard port number.

When prompted with the WebGuard login window, select WEBWATCH or WEBSEARCH as the desired mode. Enter the ID and password and click LOGIN to sign in using the selected mode.

If connecting by entering http://www.dvronline.net, enter the NVR's IP address in the Device Address eld. Selecting the Use DVRNS option on the login window allows you to enter the NVR name registered to the FEN server instead of its IP address. You will be prompted to enter the FEN server's address and port number under Setup.

• Do not close the login window while WebGuard is running. Switching over to Web monitoring or Web Search mode

can cause a script error, requiring you to restart the

WebGuard program.

• If running

WebGuard, the bottom section of the screen may get cut o if the address bar or the status bar is shown.

In this case, change Internet Options so that the address bar or the status bar is hidden. (Tools → Internet Options → Security → Custom level... → Allow websites to open windows without address or status bars (Enable))

• To use

WebGuard on Microsoft Windows Vista or above, launch Internet Explorer by right-clicking on the icon and

selecting the Run as administrator option. Otherwise, certain

WebGuard functions might not be available.

Part 5 - WebGuard

IDIS Web

Page 79

Part 5 - WebGuard

• Launching a new version of WebGuard for the rst time can cause Internet Explorer to load information from the

previous version. In this case, navigate to Tools → Internet Options → General, delete temporary Internet les, and then restart

WebGuard.

• On Microsoft Windows Vista or above, lowered image transmission rate can prevent the screen from being displayed or updated. In this case, we recommend that you disable the computer's auto tuning function. Open the command prompt as an administrator. (Start → Accessories → Command Prompt → Right-Click and then select Run as administrator) Type in "netsh int tcp set global autotuninglevel=disable" and then press Enter. Restart the computer to apply the change. To enable auto tuning again, launch the command prompt as an administrator and then type in "netsh int tcp set global autotuninglevel=normal". Restart the computer to apply the change.

Web Monitoring Mode

A remote web monitoring program that allows you to monitor images from remote locales in real-time.

1 2

! @

7 8 9

Press

to log out WebGuard.

Click to switch over to Web Search mode.

Place the mouse pointer on the WebWatch logo to check WebGuard's version.

Displays the current time and login information of WebGuard.

Page 80

Part 5 - WebGuard

Select the desired mode. Changing the mode places the selected camera in the rst cell of the layout that will be changed.

Select the camera you wish to monitor.

Used to adjust live video quality.

Used to control a PTZ camera at a remote location.

Controls remote alarm out devices.

Click

to congure rendering mode and OSD settings. Select rendering mode to adjust the video

output rate or select which OSD elements to display on the screen from the OSD list.

Click

to save the current video screen as an image le.

Click

to congure event, camera, stream settings, etc of NVR at remote locales.

Event status window at the bottom of the screen displays a list of events detected at remote locales.

Select a camera from the screen and right-click to bring up the pop-up menu.

• Change Camera Title: Used to change the camera's name.

Renaming the camera in Web Live mode does not aect the camera's name on the remote system. If no name is entered for the camera, the name used at the remote locale is shown on the screen.

• Enable Audio: Enables audio transmission with remote locales. Select to display buttons.

Enables transmission of audio to the remote locale via microphone.

Enables playback of audio from the remote locale on speakers.

Enables two-way audio communication with the remote locale.

Disables audio transmission.

If the remote locale connected to supports audio transmission, icon appears on the corresponding camera screen.

• Aspect Ratio: Changes the aspect ratio of the video displayed on the screen.

- Fit to Screen: Fit the video to the size of the camera screen.

- Fit to Aspect Ratio: Resizes camera screen to original aspect ratio of the video.

- Half Size (x0.5) - 4 Times Bigger (x4): Displays the camera videos in the selected size based on the original size of the video. For example, original size (x1) displays the video in its original size. Half size (x0.5) through 4 times larger (x4) options are only available if there is enough space on the camera screen to accommodate the selected size.

• Anti-Aliasing Screen: Removes stair step eect (blocks) that is caused when zooming a video to improve overall quality of video output.

Page 81

Part 5 - WebGuard

Web Search Mode

A remote web search program that allows you to search for recordings from remote locales in real-time.

While in Web Search mode, connection to remote locales will terminate automatically after 30 minutes of inactivity.

1 2

$ %

^ &

6 7

(

)

Press

to log out WebGuard.

Click

to switch over to Web monitoring mode.

Place the mouse pointer on the WebSearch logo to check WebGuard's version.

Displays time information of the video recording from the remote NVR.

Apply image lters (Sharpen, Blur, Equalizer, Interpolation, and Revert) to the images.

Image calibration is applied only during the paused state.

Page 82

Part 5 - WebGuard

Zoom in or out on the video.

Adjust image brightness.

Use the playback controls to play back video.

Go to First Fast Forward

Play by Frame (backwards) Play by Frame (forwards)

Rewind Go to Last

Play/Pause

Select the desired mode.

Use the calendar to search for video recordings by specic dates. Dates containing video recordings are highlighted in black. Selecting a date containing video recording

data loads the earliest recording from that date(paused state). Selected date is highlighted in red.

Click to designate recent recordings you wish to search and then jump to a specic point in the recording.

Select to enable time lapse search mode and search/play back video recordings in chronological order. In Time Lapse Search mode, search is conducted by selecting days on the calendar. The time table at the bottom displays recording data information for the selected date. Select a point in time to display video from that moment. If multiple recordings are available for the selected point in time, you can select the desired segment.

Select to enable event search mode and search for events matching user-designated parameters.

Click to congure rendering mode and OSD settings. Select rendering mode to adjust the video output rate or select which OSD elements to display on the screen from the OSD list.

Click

to save the video recording as an executable le.

Click

to save the current video screen as an image le.

Click

to print the current video screen using a printer connected to the computer.

Click to reload recent video recordings from remote locales.

(

Indicates the selected camera's recording data on a time bar. If the camera's system clock has been changed to a point in the past and more than one recording exists at the same point in time as a result, you will be able to choose which segment to search from the segment menu on the upper right portion of the time table.

)

Select a camera from the screen and right-click to bring up the pop-up menu.

• Change Camera Title: Used to change the camera's name.

Renaming the camera in Web Search mode does not aect the camera's name on the remote system. If no name is entered for the camera, the name used at the remote locale is shown on the screen.

• Enable Audio: If audio was recorded with the video, enabling this option plays audio upon playback (limited to single-screen playback).

• Aspect Ratio: Changes the aspect ratio of the video displayed on the screen.

• Anti-Aliasing Screen: Removes stair step eect (blocks) that is caused when zooming a video to improve overall quality of video output.

Page 83

Part 6 - Appendix

System Log Types

Boot Up Panic On

System Shutdown Panic O

Restart Clear All Data

Upgrade Success Clear Disk

Upgrade Error Format Disk

Power Failure Disk Full

Time Changed Auto Deletion

Time Zone Change Search Begin

Time Sync. Search End

Time Sync. Failed Clip-Copy Begin

Disk Bad Clip-Copy End

Logout Clip-Copy Failure

Setup Begin Clip Copy User

Setup End Clip-Copy Begin

Remote Setup Change Clip-Copy Finished

Remote Setup Failure Clip Copy Duration of Video

Setup Import Clip Copy Camera

Setup Import Failure Callback Failed

Setup Export Factory Reset

Setup Export Failure Camera Upgrade Begin

Setup Export Canceled Camera Upgrade End

SNS Failure Camera Upgrade Failure

Schedule On Camera Upgrade User

Schedule O Camera Upgrade Camera

Page 84

Part 6 - Appendix

Error Code Types

Upgrade Error Codes

No. Type No. Type

0 Unknown Error 301 Remote Network Error

1 Incorrect File Version 302 No Remote Upgrade Permission

2 Incorrect OS Version 303 Remote Upgrade File Save Failure

3 Incorrect Software Version 304 Remote Upgrade Cancelled by User

4 Incorrect Kernel Version 400 USB Storage Device Mount Failure

100 Storage Device Mount Failure 401 USB Storage Device File Read Failure

101 File Not Found 402 USB Storage Device File Copy Failure

102 File Decompression Failure 403 USB Device Not Connected

103 LILO Execution Failure 404 USB Storage Device in Use

104 Reboot Failure 405 Unsupported File System

105 Improper File 500 Clip Copy in Progress: Upgrade Not Available

300 Remote Connection Failure

Clip Copy Error Codes

No. Type No. Type

0 Unknown Error 12 Disk Error

1 Device Error 13 Clip Player Execution File Not Found

2 Device Connection Failure 14 Clip Player Execution File Access Failure

3 CD Media Not Found 15 Clip Player Execution File Save Failure

4 Incorrect Media 16 Image Generation Failure

5 File Name Taken 17 Burn Failure

6 Insucient Space 18 Burn Time Overrun

7 Temporary File Generation Failure 19 Device Connection Failure

8 Disk Access Failure 20 Device in Use

9 Disk Format Failure 21 Unsupported File System

10 Database Changed 22 Data Validation Failure

11 Save Failure 23 No Saved Data within Range

Page 85

Part 6 - Appendix

Network Error Codes

No. Type No. Type

0 Cause of Failure Unknown 20 Connection Cancelled by User

1 Normal Logout 21 No Response from Network Device Host

2 All Channels in Use - Connection Denied 22 High Network Noise Level

3 Incorrect Product Version Info 23 Transmission Queue Full

4 Incorrect User Name or Password 24 Incorrect OEM Info

5 Forced Disconnection by Admin 25 No Search Permission

6 Timeout 26 Port in Use

7 Network Device Terminated 27 SSL Connection Failure

8 Unable to Connect: No Available Port 28 Network Timeout

9 Server Not in Operation: Unable to Connect 29 Network Device Host Timeout

11 Network Unavailable 30

RTP via TCP Not Supported by Network Device Host

12 Dierent Network Zone: Unable to Access 31 Socket Error

13 Connection Timeout 100 Unknown CODEC

14 Forced Disconnection by Network Device 101 .jpeg CODEC (not supported)

15 Network Device Host Terminated 103 .mpeg4 CODEC (not supported)

16 Unable to Route to Network Device Host 400 Unsupported Resolution

17 Connection Severed -1 Normal Access

Page 86

Part 6 - Appendix

Troubleshooting

Problem Solution

The main unit won't turn on.

• Check the power cable connection status.

• Check the power outlet.

Unable to display Live video.

• Check the camera's video cable connection status.

• Check the monitor's video cable connection status.

• Check the camera's power setting.

• Check the camera lens settings.

NVR stopped working in the middle of a recording.

• Hard disk may be full. Delete video recordings to free up space.

• Set the NVR to Recycle mode. For more information, refer to the General on page 44.

icon is shown, but video is

not being recorded.

If the Pre-Event is enabled, the and icons appears when recording is not in progress, or the

and icons appear when an event occurs and recording

is in progress. For more information, refer to the Schedule on page 45.

The NVR keeps on rebooting during a system upgrade without completing the upgrade.

Check the upgrade le's version. To downgrade to a previous version, you must rst press the factory reset button and reset all NVR settings to their factory defaults. A factory reset will clear all NVR settings congured by the user. For more information on factory reset, refer to the Factory Reset section on page

90.

Page 87

Part 6 - Appendix

Specications

These product specications may change without prior notice.

General

Exterior Dimensions (W x H x D)

430mm x 88mm x 415mm

Weight (Main Unit) 6.4kg (with 1HDD)

Weight (Packaging) 9.4kg (with 1HDD)

Packaging Dimensions (W x H x D)

535mm x 238mm x 535mm

Working Temperature 0°C – 40°C

Operating Humidity 0% – 90%

Power 100V-240V~

Power Consumption 75W (with 6HDDs)

Certications FCC, UL, CE, CB, PSE

Video

Video In 32 cameras (Up to 16 BNC, Up to 32 IP cameras)

Monitor Out

HDMI: 1 HDMI VGA: 1 DB15

Video Resolution 1920 x 1200, 1920 x 1080, 1680 x 1050, 1600 x 1200

Recording Speed (IPS) 960ips @ Full HD

Playback Speed (IPS) 120ips @ Full HD

I/O

Alarm In 16TTL, NC/NO programmable, 2.4V (NC) or 0.3V (NO) threshold, 5V DC

Alarm Out 4 relay output, NC/NO, 2A@125V AC, 1A@30V DC

Alarm Reset In 1 TTL, terminal block

Internal Buzzer 78dB at 10cm

Network Connection 10Mbps/100Mbps/1Gbps Ethernet

Audio In 16 lines, RCA

Audio Out 1 line, RCA

Text I n POS Interface, ATM Interface

* If more than 16 cameras from video encoders are registered on the NVR, video may not be displayed smoothly in a

remote program.

Page 88

Part 6 - Appendix

Connectors

Video In Ethernet: 1 port, Composite: 16 BNC

Video Loop Composite: 16 BNC

Monitor Out

HDMI: 1 HDMI VGA: 1 DB15

Audio In 16 RCA connectors

Audio Out 1 RCA connector

Alarm Terminal block

Ethernet Port 1 RJ-45

eSATA Ports 2 eSATA ports

RS-232 Serial Port Terminal block, text insertion (POS/ATM)

RS-485 Serial Port Terminal block, telemetry control, remote control keyboard (programmable)

IR Remote Control Port Remote Control

USB Ports

2 x USB 2.0

(5V, less than 0.5A)

Storage

Internal Storage 6 SATA2 bays

External Storage 2 eSATA Ports

Clip Copy Device USB Storage Device (USB HDD, USB Memory, etc.)

Some hard disks may not function properly when mounted on to this product. Refer to the compatibility chart below before mounting any add itional hard disk on to the product. Hard disk compatibility chart is subject to change without notice. Contact your retailer for the latest compatibility chart.

Storage Manufacturer Model Note

1TB

Seagate ST1000VX001

TOSHIBA DT01ACA100

2TB

Western Digital WD20PURX-64P6ZY0

TOSHIBA DT01ACA200

3TB

Western Digital WD30PURX-64P6ZY0

TOSHIBA DT01ACA300

4TB Western Digital WD40PURX-64GVNY0

Page 89

Part 6 - Appendix

Audio Recording 35

Event Monitoring 33

FEN 56

Live Mode 28

Motion Search 74

Mouse 37

OSD 57

Panic Recording 34

Pre-Event 46

PTZ Control 32

Recording 34

Record Setup 44

Schedule 45

Search 70

Storage 41

Stream 68

Text-In 52

Timelapse Mode 70

Time-Lapse Search 71

Upgrade 69

Video-Analytics 47

WebGuard 78

Wizard 22

Index

V1.0

Page 90

ATV DR-6232H Operation Manual

Specifications and Main Features

Frequently Asked Questions

User Manual