ATV CHVD37PS User Manual

Height Strip Covert Camera

Please read this manual thoroughly before use, and keep it handy for future reference.

Design and specifications are subject to change without notice.

WARNINGS AND CAUTIONS:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR
MOISTURE. DO NOT INSERT ANY METALLIC OBJECTS THROUGH THE VENTILATION GRILLS OR
OTHER OPENINGS ON THE EQUIPMENT.

CAUTION:

CAUTIONCAUTION

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER(OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

EXPLANATION OF GRAPHICAL SYMBOLS

The lightning flash with arrowhead symbol, within an equilateral triangle, is
intended to alert the user to the presence of uninsulated "dangerous voltage"
within the product's enclosure that may be of sufficient magnitude to constitute a
risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to
the presence of important operating and maintenance (servicing) instructions in the
literature accompanying the product.

PRECAUTIONS

Installation -----------------------------------

Do not install the unit in an extremely hot or humid place or in a place subject to excessive dust.

Cleaning --------------------------------------

Clean the unit with a slightly damp soft cloth.
Use a mild household detergent. Never use strong solvents such as thinner or benzine as
they might damage the finish of the unit.

Retain the original carton and packing materials for safe transport of this unit in the future.

- ii -

FCC COMPLIANCE STATEMENT

FCC INFORMATION : THIS EQUIPMENT HAS BEEN TESTED

AND FOUND TO COMPLY WITH THE LIMITS FOR A CLASS A DIGITAL
DEVICE, PURSUANT TO PART 15 OF THE FCC RULES. THESE
LIMITS ARE DESIGNED TO PROVIDE REASONABLE PROTECTION
AGAINST HARMFUL INTERFERENCE WHEN THE EQUIPMENT IS
OPERATED IN A COMMERCIAL ENVIRONMENT. THIS EQUIPMENT
GENERATES, USES, AND CAN RADIATE RADIO FREQUENCY
ENERGY AND IF NOT INSTALLED AND USED IN ACCORDANCE WITH
THE INSTRUCTION MANUAL, MAY CAUSE HARMFUL INTERFERENCE
TO RADIO COMMUNICATIONS. OPERATION OF THIS EQUIPMENT IN
A RESIDENTIAL AREA IS LIKELY TO CAUSE HARMFUL
INTERFERENCE IN WHICH CASE THE USER WILL BE REQUIRED TO
CORRECT THE INTERFERENCE AT HIS OWN EXPENSE.

CAUTION : CHANGES OR MODIFICATIONS NOT EXPRESSLY

APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE
COULD VOID THE USER'S AUTHORITY TO OPERATE THE EQUIPMENT.

THIS CLASS A DIGITAL APPARATUS COMPLIES WITH CANADIAN
ICES-003.

NORME NMB-003 DU CANADA.

CE COMPLIANCE STATEMENT

WARNING

THIS IS A CLASS A PRODUCT. IN A DOMESTIC ENVIRONMENT THIS
PRODUCT MAY CAUSE RADIO INTERFERENCE IN WHICH CASE
THE USER MAY BE REQUIRED TO TAKE ADEQUATE MEASURES.

- iii -

IMPORTANT SAFEGUARDS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4 . Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the
manufacturer's instructions.

8. Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type
plug. A po la ri ze d pl ug h as t wo b la de s wi th o ne w id er t ha n th e ot he r.
A gr ou nd in g ty pe p lu g ha s tw o bl ad es a nd a t hi rd g ro un di ng p ro ng .
The w id e bl ad e or t he t hi rd p ro ng a re p ro vi de d fo r yo ur s af et y. If t he
provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.

10.Protect the power cord from being walked on or pinched particularly
at plugs, convenience receptacles, and the point where they exit from
the apparatus.

11. On ly u se a tt ac hm en ts /a cc es so ri es s pe ci fi ed b y th e ma nu fa ct ur er.

12. Use only with the cart, stand, tripod, bracket,
or table specified by the manufacturer,
or sold with the apparatus.
When a cart is used,use caution when moving
the cart/apparatus combination to avoid injury
from tip-over.

13. Unplug this apparatus during lightning storms or when unused for
long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way, suc h as
power-supply cord or plug is damaged, liquid has been moisture, does
not operate normally, or h as b ee n dr op pe d.

15. CAUTION THESE SERVICING INSTRUCTIONS AR E FO R US E BY
QUALIFIED SERVICE PERSONNEL ONLY. TO R ED UC E TH E RI SK
OF ELECTRIC SHOCK DO NOT PERFORM AN Y SERVICING OTHER
THAN THAT CO NTA IN ED I N TH E OP ER ATING INSTRUCTIONS
UNLESS YO U QR E QU AL IF IE D TO D O SO .

16. Use satisfy clause 2.5 of IEC60950-1/UL60950-1 or Certified/Listed
Class 2 power source only.

- iv -

INTRODUCTION

Features:

High resolution and high performance 1/3" Color CCD

Excellent picture quality

600 lines of resolution (Color)

0.1 lux(Color), 0.04ux(B/W) @ F1.2 - 50IRE Sensitivity

Auto electronic shutter [1/60(1/50) ~ 1/100,000]

Auto white balance

AGC (Auto Gain Control)

Use Certified / Listed Class 2 power source only

2D DNR

(Digital Noise Reduction)

Side Light Compensation

3.7mm Pin hole Lens

BNC (Video connection), 2-Pin terminal block (Power)

Operates in DC12~15V +/- 10%

IMPORTANT : The user of this camera is responsible for
checking and complying with local, state, and federal laws
and statutes concerning the recording and monitoring of
audio signals.

1

Step 1

77 3/4 "

Drill feed-thru hole for cable on mounting surface 77 3/4" above the finished floor.

2

Step 2

Feed wire through the 3/4" hole on the gimble mount.

3

Step 3

Center the gimbal mount to mounting surface and mark the mounting holes for the gimbal
mount on the surface.

Secure the gimbal mount to the surface using installer supplied self tappers for aluminum
frame structure.

If mounting on soft surface such as drywall be sure to use to use anchors.

4

Step 4

Completing the housing installation

Remove the five white head M4 screws that hold the face plate to the housing
and set the face plate aside.

Feed the wire coming through the gimbal mount through the 3/4" hole in the
back of the camera housing.

Attach the camera housing to the gimbal mount using the M6 Allen head screws
and washer previously removed.

Place the external tooth washer between the housing and the gimbal mount then
the split lock washer on the M6 screw and insert the screw into the housing
through the gimbal mount and external tooth lock wasker.

Install the bolt and washers assembly at the bottom and top of the gimbal mount
finger tight. (See Figure-1)

M6 Allen head screw

Split lock washer between gimbal mount and housing

External tooth lock washer under head of bolt

Figure-1

After connecting the video and power to their proper connections replace the
face plate that was removed in an earlier step using the five screws.

Adjust the position of the housing in the gimbal mount for the proper view and
then tighten the top and bottom Allen head screws using an Allen head wrench.

Verify that the housing is in the proper position and is secure.

5

Optional Camera Height Setting

1. The CHVD37JB/CHVD37PB/CHVD37PS Height strip camera has the
capability to be set in the housing at 5ft or 5.5ft above the floor.
The default setting of the camera is set to 5.5ft.
If the lower setting is desired the following housing change must be
completed.

* Remove housing from gimbal

1

* Note the position of the hole in the housing base for cable throughput

2

Figure-2

[ft] [cm]

Figure-3

The cable hole is at the top of the mounting bracket

* Remove three Allen head screws along each side of the housing and
separate the front cover with the camera from the housing base.

Allen head screw

* Replace the front cover with the camera to the housing base after
turning the cover 180
Replace the three Allen head screws along each side of the housing
and continue the installation

o

from original position.

2

1

* From to to change the camera position. (See Figure-2)

2. Camera lens position can be adjusted up and down 5 degrees.

o

92

3. Two height marker strips are provided, one marked in feet
and one marked in centimeters. Use the appropriate one.
(See Figure-3)

o

92

o

92

o

5

o

5

6

DIMENSIONS

HEIGHT STRIP CAMERA

CHVD37JB
CHVD37PB
CHVD37PS

inch

7

SPECIFICATIONS

Power

General

Connector

&

etc.

MODEL

Power source
Power consumpti on
Image sensor
Number of pixels
Scanning system
Scanning freque ncy
Sync. system
Electronic shut ter
Resolu tion
Min. illuminati on

Side Lig ht Compen sation
Digita l Noise Red uction

Video out put
S/N ratio
AGC
Day / Night

White Balance
Power input
Video ou tput

Lens mount
Lens
Operating Temperature
Operating humid ity

External Dimens ion

Weight

NTSC

DC12~15V +/-10%

130mA (1.5 Watts)

768(H) x 494(V)

15.734KHz(H) x 59.94Hz(V)

1/60 ~ 1/100,000 sec.

0.1 lux(COLOR), 0.04 lux(BW) @ F1.2, 50 IRE

1/3" Color CCD

600 TV lines (Color)

1.0 Vp-p (75 ohm, composite)
More than 50dB (AGC off)

Terminal Block

BNC Connector

F3.7mm Pin hole Fixed

o o o o

-10 C ~ +50 C [14 F ~ 122 F
0 ~ 96% (non-condensing)

1.8"(W) x 34.4"(H) x 1.4"(D)

set : 1260g packing : 2035g

2:1 interlace

15.625KHz(H) x 50Hz(V)

Internal

1/50 ~ 1/100,000 sec.

Auto

2D DNR

ON

Auto

Auto(ATW)

Fixed mount

752(H) x 582(V)

* Use the power consumption 2W over.

PAL

]

8

Height Strip Covert Camera

PRINTED IN KOREA