ATV C700TDN User Manual

INSTRUCTION MANUAL

DNR Super

High Resolution

Day & Night

Color Camera

1/3” INTERLINE TRANSFER CCD

HIGH RESOLUTION

Please read this manual thoroughly before use and keep it handy for future reference.

WARNINGS AND CAUTIONS

r

A

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
PRODUCT TO RAIN OR MOISTURE. DO NOT INSERT ANY METALLIC OBJECT
THROUGH THE VENTILATION GRILLS OR OTHER OPENINGS ON THE EQUIPMENT.

CAUTION

CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER(OR BACK).

NO USER-SERVICABLE PARTS INSIDE.

REFFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

EXPLANATION OF GRAPHICAL SYMBOLS

is intended to alert the user to
voltage''
to constitute a risk of

The exclamation point within an equilateral triangle is intended to alert
the user to the
(servicing) instructions in the liter

The lightning flash with arrowhead symbol, within an equilateral triangle,

within the product's enclosure that may be of sufficient magnitude

electric shock to persons.

presence of important operating and maintenance

PRECAUTIONS

Safety

Should any liquid or solid object fall into the cabinet,
unplug the unit and have it checked by
qualified personnel before operating it any further.

Unplug the unit from the wall outlet if it is not going to
be u

sed for several days or more.
To disconnect the cord, pull it out by the plug. Neve
pull the cord itself.

llow adequate air circulation to prevent internal heat
build-up. Do not place the unit on soft surfaces (rugs,
carpets, sofas, etc.) or near materials (curtains,
draperies) that may block the ventilation holes.

Height and vertical linearity controls located on the
rear p

anel are for special adjustments by qualified

personnel only.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

the presence of uninsulated ''dangerous

ature accompanying the product.

Installation

Do not install the unit in an extremely hot or humid place
or in a place subject to excessive dust, mechanical
vibration.

The unit is not designed to be waterproof.
Exposure to rain or water may damage the unit.

Cleaning

Clean the unit with a slightly damp soft cloth.
Use a mild household detergent. Never use strong
solv

ents such as thinner or benzine as they might

damage the finish of the unit.

Retain the original carton and packing materials for safe
tran

sport of this unit in the future.

ii

FCC COMPLIANCE STATEMENT

INFORMATION TO THE USER: THIS EQUIPMENT HAS BEEN TESTED

AND FOUND TO COMPLY WITH THE LIMITS FOR A CLASS A DIGITAL DEVICE,
PURSUANT TO PART 15 OF THE FCC RULES. THESE LIMITS ARE DESIGNED
TO PROVIDE REASONABLE PROTECTION AGAINST HARMFUL
INTERFERENCE WHEN THE EQUIPMENT IS OPERATED IN A COMMERCIAL
ENVIRONMENT. THIS EQUIPMENT GENERATES, USES, AND CAN RADIATE
RADIO FREQUENCY ENERGY AND IF NOT INSTALLED AND USED IN
ACCORDANCE WITH THE INSTRUCTION MANUAL, MAY CAUSE HARMFUL
INTERFERENCE TO RADIO COMMUNICATIONS.
OPERATION OF THIS EQUIPMENT IN A RESIDENTIAL AREA IS LIKELY TO
CAUSE HARMFUL INTERFERENCE IN WHICH CASE THE USER WILL BE
REQUIRED TO CORRECT THE INTERFERENCE AT HIS OWN EXPENSE.

CAUTION: CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED

BY THE PARTY RESPONSIBLE FOR COMPLIANCE COULD VOID THE USER'S
AUTHORITY TO OPERATE THE EQUIPMENT.

THIS CLASS A DIGITAL APPARATUS COMPLIES WITH CANADIAN ICES-003.

CET APPAREIL NUMÉRIQUE DE LA CLASSE A EST CONFORME À LA NORME
NMB-003 DU CANADA.

CE COMPLIANCE STATEMENT

WARNING: This is a Class A product. In a domestic environment this product

may cause radio interference in which case the user may be required to take
adequate measures.

iii

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in a
manufacturer’s instructions.

8. Do not install near any heat sources su
stoves, or other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug.
A polari
grounding type plug has two blades and a third grounding prong. The
wide blade or the third prong are provided for your safety. If the provided
plug does not fit into your outlet, consult an electrician for replacement of
the obsolete outlet.

10. Protect the power cord from being walked o
plugs, convenience receptacles, and the point where they exit from the
apparatus.

11. Only use attachments/accessories

12. Use only with the cart, stand, tripod, bracket, or table
spe
When a cart is used, use caution when moving the
cart/apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when
unused for long periods of time.

14. Refer all servicing to qualified service personnel.
Servicin
damaged in any way, such as power-supply cord or plug
is damaged, liquid has been moisture, does not operate normally, or has
been dropped.

15. CAUTION – THESE SERVICING INS
QUALIFIED SERVICE PERSONNEL ONLY. TO REDUCE THE RISK OF
ELECTRIC SHOCK DO NOT PERFORM ANY SERVICING OTHER
THAN THAT CONTAINED IN THE OPERATING INSTRUCTIONS
UNLESS YOU QRE QUALIFIED TO DO SO.

16. Use satisfy clause 2.5 of IEC60950-1/UL60
Class 2 power source only.

zed plug has two blades with one wider than the other. A

specified by the manufacturer.

cified by the manufacturer, or sold with the apparatus.

g is required when the apparatus has been

ch as radiators, heat registers,

n or pinched particularly at

TRUCTIONS ARE FOR USE BY

ccordance with the

950-1 or Certified/Listed

iv

CONTENTS OF PACKAGE

Installation of the camera must be performed by qualified service personnel in
accordance with all local and national electrical and mechanical codes.

Carefully remove the color camera and its accessories from the carton
and verify that they were not damaged in shipment.

The contents of the package includes:

1. Color CCD camera

2. Mini-DIN connector (for video-o

3. CS adapter ring for C mounting “C” lenses

4. This manual

r dc-type auto-iris lens)

TABLE CONTENTS

INTRODUCTION-------------------------------------------------------------------------------1

COMERA OVERVIEW------------------------------------------------------------------------2

OSD MENU STRUCTURE-------------------------------------------------------------------3

DC IRIS LENS----------------------------------------------------------------------------------10

SPECIFICATIONS----------------

-------------------------------------------------------------11

v

INTRODUCTION

The camera provides high-quality images using SONY 1/3” CCD and digital
Signal process LSIs.

Features:

● 1/3" EXv

Digital Wide Dynamic Range (Xtended Dynamic Range)

●

●

Excellent picture quality

●

700 lines of resolution

● 0.15Lux(Col

●

Auto electronic shutter [1/60(1/50) ~ 1/10,000] and manual electronic
shutter modes

OSD (On Screen Display)

●

●

Auto and manual white balance modes

●

Auto BLC and HLC

Day & Night (Auto/Manual)

●

Privacy Zone 4 point, Motion Detection 4 Point

●

MIRROR, SHARPNESS, HUE, CONTRAST, GAIN

●

AGC (Auto Gain Control)

●

VIDEO OUT(BNC)

● Internal

●

Quick connect for DC lens with 4-pin connector

●

Operates in 12VDC or 24VAC

●

Operates in 100-240VAC

●

Use Certified / Listed Class 2 power source only.

●

If using DC 12V power adaptor, Please use a power supply capable of
supplying over 5.5 Watts.

● Auto White Defect

iew HAD CCD Ⅱ for an image of high sensitivity

or), 0.01Lux(B/W) @ F1.2 Sensitivity

IMPORTANT : The user of this camera is responsible for
checking and complying with local, state, and federal laws and
statutes concerning the recording and monitoring of audio
signals.

1

CAMERA OVERVIEW

n Left Button
o Up

Button

p Enter
q Right
r Do
s Po
t
u
v AC Pow

2

Button

Button
wn Button
wer Indicator

Video Output Connector (BNC)
AC/DC Compatible Input Terminal

er Cord

OSD MENU STRUCTURE

SETUP MENU (page 1)

LENS
SHUTTER/AGC
WHITE BAL
BACKLIGHT
PICT ADJUST
ATR
MOTION DET

NEXT (page2)
EXIT SAVE ALL

LENS

AUTO ↵
MANUAL

SHUTTER/AGC

AUTO↵
MANUAL↵

WHITE BALANCE

ATW ↵
PUSH
USER 1↵
USER 2↵
ANTI CR
MANUAL↵
PUSH LOCK

BACKLIGHT

OFF
BLC
HLC

PICTURE ADJUST↵

MIRROR
BRIGHTNESS
CONT

RAST
SHARPNESS
HUE
GAIN

RETURN

ATR

OFF
ON↵

MOTION DET

OFF
ON↵

3

SETUP MENU (page 2)

PRIVACY
DAY/NIGHT
NR
CAMERA ID
LANGUAGE
CAMERA RESET

BACK (page 1)
EXIT SAVE ALL

NR↵

NR MODE
Y LEVEL
C LEVEL

RETURN

PRIVACY

OFF
ON↵

CAMERA ID

OFF
ON↵

DAY/NIGHT
AUTO
COLOR
B/W↵

LANGUAGE

ENGLISH
日本語
DEUTSCH
FRANCAIS
PYCCKNN
PORTUGUES
ESPANOL

CAMERA RESET

(return the camera to
factory defaults)

4

LENS

AUTO
TYPE (DC / VIDEO)

Sets the type of mechanical iris
(Video lens is not supported)
MODE (AUTO / OPEN /
Sets the type of control to be applie

CLOSE )

d over the mechanical iris.

SPEED (0 – 255)
Sets the convergence speed of the mechanical iris.

MANUAL

Manual lens only

e

. (Not

Since Manual mode AUTO mode is changed SHUTTER/AGC to

SHUT+AUTO IRIS when MANUAL is changed to AUTO, AUTO MODE
should be changed to AUTO IRIS in SHUTTER/AGC)

SHUTTER/AGC

AUTO

HIGH L
MODE
(Note: only

Adjusts the brightness

LOW LUMINANCE

Auto Gain Control on or off

MANUAL

Auto gain control

AGC
Sets the AGC gain applied [dB] for ME (manual exposure)
(6, 12, 18, 24, 30, 36, 42, 44.8dB)

UMINANCE

(SHUT+AUTO IRIS / AUTO IRIS)

SHUT can be selected if LENS is in MANUAL mode

SHUT+AUTO IRIS is AE(

Auto Exposure) for SHUTTER is 1/500(1/480) and

MIRIS)

BRIGHTNESS (0 ~ 255)

MODE (
BRIGHTNESS (x0.25 / x0.50 / x0.75/ x1

AGC / OFF)

.00)

Amount of AGC applied in low lighting conditions

MODE (

SHUT+ AGC)

SHUTTER
Select the shutter speed (1/60, 1/120, 1

/250, 1/500, 1/1000, 1/2000, 1/4000,

1/10000)

5

WHITE BAL

(Auto Trace White balance)

ATW
SPEED (0~255)
Adjusts the pull-in speed of ATW.
DELAY CNT (0~255)
Sets the time-based hysteresis of ATW.
ATW FRAME (x0.5 / x1 / x1.5 / x2)
Sets the pull-in frame magnification.
ENVIROMENT (

INDOOR / OUTDOOR)

Preset for either indoor or outdoor applications of the ATW

PUSH

Wide range Auto White Balance mode (AWB)

USER1 & 2

Both USER 1 & 2 can be individually set up for specific applications. The gain
values for the

outdoor fixed mode are used as the adjustment items of USER1

on the internal OSD menu.
B-GAIN (0
R-GAIN (0

~255)
~255)

ANTI CR

Color rolling suppression

MANUAL

The B and R gain values for manual WB are set on this screen.
LEVEL (NTSC : 13 ~ 56) ,

(PAL : 16 ~ 78)

PUSH LOCK

PUSHLOCK is selected and the Enter input is active

BACKLIGHT

Sharpens subjects with backlight (OFF / BLC / HLC)

PICT ADJUST

MIRROR (OFF / ON) Horizontally inverts image.
BRIGHTNESS (0~255
CONTRAST (0~2
SHARPNESS (0~25
HUE (0~2
GAIN (0~2

) Sets the screen brightness.

55) Sets the screen contrast.

5) Sets the screen sharpness.

55) Adjusts the hue.

55) Adjusts the gain.

6

ATR

ATR (Adaptive Tone Reproduction) allows a

djustment of the image to assist

with widely contrasting scenes of view.
LUMINANCE (LOW / MID / HIGH)

Sets the extent of the luminance compression
CONTRAST (LOW / MIDLOW / MID / MIDHIGH / HIGH)
Sets the extent of the contrast enhancement

MOTION DET

DETECT SENSE (0~127)

Sets the motion detection sensitivity (0=low sen

BLOCK DISP (OFF / ON

/ ENABLE)

Applies a Motion block trace in the selected area. To

Enable and push centrally on the joystick. Use the

sitivity, 127=high sensitivity)

define the area, select

Joystick to navigate to the

blocks you want to Disable and not include in motion trace. To return to the
menu, push and hold central joystick for 2secs and release.

MOTION AREA (O
Enables/di

sables the motion detection

AREA SEL (1~

Selects the motion detection area

te: Set the area sel it would be better

(No
to move firstly BOTTOM and RIGHT)
TOP (NTS

C:0~244 , PAL:0~288)
0 = top
BOTTOM (NTSC:0~244 , PAL:0~28
244(288) = bottom
LEFT (NTS

C:0~474 , PAL:0~468)

0 = left
RIGHT (NTSC:0~474 , PAL:0~4
474(468) = right

N / OFF)

4)

68)

8)

MOTION DET
DETECT SENSE IIIIIIIIIII

BLOCK DISP OFF
MONITOR AREA ON
AREA SEL 1/4

TOP IIIIIIIII 000
BOTTOM IIII
LEFT III
RIGHT IIIIIIIII

RETURN

111

IIIII 076

IIIIII 000

183

PRIVACY

AREA SEL (1~4)

Selects the motion detection area

te: Set the area sel it would be better

(No
to move firstly BOTTOM and RIGHT)
TOP (NTS

C:0~244 , PAL:0~288)
0 = top
BOTTOM (NTSC:0~244 , PAL:0~28
244(288) = bottom

8)

PRIVACY

PRIVACY

AREA SEL

AREA SEL 1/4
TOP IIIIIIIIII000

BOTTOM IIIIIIIIII077
LEFT IIIIIIIIII000
RIGHT IIIIIIIIII187
COLOR 1
TRANSP 1.00
MOSAIC OFF

7

LEFT (NTSC:0~474 , PAL:0~468)
0 = left
RIGHT (NTSC:0~474 , PAL:0~4

68)

474(468) = right

COLOR (1~8)
Sets the colors of the privacy zones.

TRANSP (0.00 / 0.50 / 0.75 / 1.00)
Sets the transparency of the privacy zone area if co

lor is selected.

MOSAIC (OFF / ON)

Sets the mosaic function as the privacy to ON or OFF.
(Note: when ON, transparency needs to be set at 0.00 and privacy zones
can only be 1 color OR mosaic and not mixed)

DAY / NIGHT

COLOR (color only operation)

(monochrome only operation)

B/W
BURST (OFF / ON)
Allows the color burst signal in monochrome to be removed if required.

IR OPTIMIZER (OFF / ON)

Smart IR mode OFF or ON

MODE (ONLY IR OPTIMIZER ON, AUTO / CENTE

R)

Auto : Histogram integration mode

Center : Center p

LEVEL (ONLY IR OPTIMIZER ON, 0~

riority mode

31)

NR (2D-DNR)

This is used to remove noise from the image in low light conditions when

AGC is applied.
NR MODE (OFF, Y, C, Y/C)

Sets the 2D NR filter mode.

Y LEVEL (0-15)

Sets the Y filter (Luminance) strength.

C LEVEL (0-15)

Sets the C filter (Chrominance) strength.

8

CAMERA ID

Sets the camera ID to ON or OFF. A title of 52 characters per line can be
applied.

Use the joystick to navigate
the cursor. Pushing centrally
on the joystick will allow
selection of that character.

The arrows at the bottom
allow you to

move the cursor
without changing the
character.

CLR

nserts a space

I
POS

Allows you adjust the location of the camera ID title display. (if you move too

right side or down, it might lose ID on the screen)

much

LANGUAGE

LANGUAGE select between:

English, Japanese, German, French, Russian, Portuguese & Spanish.

CAMERA RESET

CAMERA RESET - Returns the camera to the factory default settings.

SAVE ALL

SAVE ALL - Saves all the changes made in the menu.

EXIT

EXIT – Exits the menu a

nd does not save changes made.

9

AUTO WHITE DEFECT

Push the left button for 5 seconds and enter Auto white defect menu.
Cover the lens and Enter for starting.

If white defects are over 65pcs, the camera is faulty and auto defect is
useless.

Over 70'C Auto white defect can't be activated.

10

DC IRIS LENS

r

The lens is not supplied with this camera. Purchase a lens suitable for your

irements. These cameras accept both C-and CS-mount type lens.

requ

<Notes >

For using main functions it is recommended to use Auto Iris Lens with DC

●

<INSTALLING AUTO IRIS LENS>

1. Remove the cover from the iris lens plug su

type.

● If the lens is marked with fingerprints other marks, the image quality might
be poor.

● It is recommended to use a high quality lens to improve the image quality

low illumination.

unde

pplied, and solder the lens cable to the

plug as shown below.

● Video type:
Pin 1 --- Red (Power source)
Pin 2 --- N.C
Pin 3 --- White (Video signal)
Pin 4 --- Black (GND)

● DC type:
Pin 1 --- Damping­ Pin 2 --- Damping+
Pin 3 --- Drive+
Pin 4 --- Drive-

Pin 3

Pin 1

Rib

Pin 4

Pin 2

Connector

Cover

Heat
Shrinkable
Tubes

Automatic
Iris Lens

Iris Control
Cable

Connector

2. Remove the protective cap, and attach the lens to the camera by turning clockwise.

11

SPECIFICATIONS

MODEL NTSC PAL Free

Power source

Power consumption 3.5 Watts (300mA) 4.0 Watts(60mA)

Image sensor 1/3″ SONY EXview HAD CCD II

Total pixels 1020(H) x 508(V) 1020(H) x 596(V)
Effective pixels 976(H)x494(V) 976(H)x582(V)
Scanning system 2:1 Interlace

Scanning frequency

Sync. system Internal
Electronic Shutter 1/60 ~ 1/10,000 sec 1/50 ~ 1/10,000 sec
Resolution 700TVL
Min. illumination 0.15lux
Video output 1.0Vp-p (75 ohm, composite)
S/N ratio More then 50dB (AGC OFF)

General

Camera Control Internal OSD Key

ATR (Adaptive Tone
Reproduction)
Backlight OFF / BLC / HLC

F

Day & Night Color / BW / Auto
MD (Motion Detection) "On (4 areas) / Off Adjustable Size & Sensitivity"

U

PM (Privacy Masking) 0 ~ 4 zone

N

WB (White Balance) ATW/ PUSH/ USER1/ USER2/ ANYICR/ MANUAL/ PUSH LOCK

C

AGC (Auto Gain Control) On / Off

T

Exposure Auto Iris / Auto Iris + Electronic Shutter

I

Brightness 0 ~ 255 steps
Contrast 0 ~ 255 steps

O

Sharpness 0 ~ 255 steps

N

HUE 0 ~ 255 steps
Gain 0 ~ 255 steps
NR(Noise Reduction) OFF / Y / C / Y, C
Mirror ON/OFF

Power input 2-pin terminal block Power Cord
Video output BNC connector

Connector & etc.

Auto iris output 4-Pin Mini Din jack (standard connection)
Lens Mount C/CS Mount (Selected through back focus)
Operating temperature -10ºC ~ +50 ºC
Operating humidity 0~96% (non-condensing)
External dimension 88(W) x 275(H) x 88(D)mm
Weight 240g 440g

Power

/ AC 24V±10%

DC 12V

15.734KHz(H)
x 59.94Hz(V)

LUMINANCE(L/M/H), CONTRAST(L/LM/M/MH/H)

15.625KHz(H) x 50Hz(V)

100-240V~50Hz

±1Hz

12

DNR Super High Resolution

Day & Night Color Camera

PRINTED IN KOREA 50303278B

2