Attwood 66514, 66516, 66510, 66513, 66512 User Manual

...

(4.19cm)

1.650"

Figure 2

(3.63cm)

1.429"

• Location on vessel must be able to withstand loads specified in application section.

• Location is large enough and wide enough to accommodate the entire cleat body.

Figure 1

• Access to the underside of the vessel is necessary for both models in order to tighten

FLUSH CLEAT TEMPLATES

See ABYC Reg. H-40 for details and ratings.

the fasteners.

Select an installation location that meets the following criteria:

WARNING:

Installation Instructions

SAVE THESE INSTRUCTIONS

Form Number 69343 Rev. G 04-04

APPLICATION

Attwood flush pull-up cleats provide easy fittings for mooring and anchoring applications.

NOTE: It is recommended that the installation of the Attwood Flush Cleats be done by a

boat builder, boat dealer, or a qualified marine mechanic.

REQUIRED FOR INSTALLATION

• Adjustable wrench • Sabre saw

• Length of 3/8" (9.5mm) I.D. hose • Screwdriver

• Cordless drill and bits • Marine sealant

To prevent personal injury, always disconnect the power source when installing or

servicing this product. Always remove the boat from the water before using any 120V AC

power tools.

LOCATION

4" and 6" Flush Mounted Cleat

66510, 66511, 66512, 66513, 66514, 66516

6" Cut-Out Template

(5.08cm)

1" Radius

6.475" (16.45cm)

2.220" (5.64cm)

4" Cut-Out Template

7/8" Radius

(4.45cm)

1.75"

1.657" (4.21cm)

4.764" (12.1cm)

The Flush Cleats are not to be used for towing, lifting, or for any other anchoring application

beyond those listed above. Any misuse of the intended application may result in personal

injury and/or damage to the boat.

4. Ensure the screw is long enough to provide for proper engagement with the nut. Attach

washers and nuts to the studs or screws and tighten.

WARNING:

3. Align backing plate with the underside of the cleat. For the 4" thru-bolt version use (4)

#10 machine screws, locking washers and nuts (regular washers and nylock nuts can

be substituted). For the 6" thru-bolt version use (4) 1/4"-20 machine screws, locking

washers and nuts (regular washers and nylock nuts can be substituted).

and drill four 1/4" (6.4mm) holes where indicated (thru-bolt cleat only).

sealant around the edge of the cut-out and place cleat in hole cut-out.

FLUSH CLEAT INSTALLATION INSTRUCTIONS

NOTE: Before you drill or cut a hole on your boat, BE ABSOLUTELY CERTAIN there is

room for the unit beneath the deck or gunwale where it will be installed. The cleat mechanism,

in the down position, will be recessed beneath the deck or gunwale.

1. Use templates provided to mark opening in deck (Figure 1 or 2). Cut using sabre saw

2. Remove the supplied fasteners from the studded cleat. Apply a small bead of marine

ATTWOOD LIMITED WARRANTY

ATTWOOD CORPORATION, 1016 North Monroe, Lowell, Michigan 49331 (“Attwood”)

warrants to the original consumer purchaser that Attwood brand products will be free from

defects in materials and workmanship under normal use and service for one year from the

date of original consumer purchases.

This limited warranty is not applicable if the product has been damaged by accident,

improper installation, unreasonable or improper use, lack of proper maintenance,

unauthorized repairs or modifications, normal wear and tear, or other causes not

arising out of defects in materials or workmanship.

Attwood products are warranted for use on pleasure boats. Any other use — including

but not limited to commercial, racing, or non-marine use — are not covered under this

warranty. Attwood’s obligation under this warranty is limited to repair of the product at

Attwood’s plant or replacement of the products at Attwood’s option without expense

to the original consumer purchaser. Any expenses involved in the removal, reinstallation

or transportation of the product are not covered by this warranty.

The product must be returned to Attwood’s plant at the address above, postage prepaid,

and insured with proof of original purchase including date.

Hose Fitting

•

Lock Washer

Nut

•

(Sold Separately)

Receptacle

Water

Backing Plate

•

Marine Sealant

Cut-Out Hole

•

Tension/Travel

Adjustment

Set Screw

Figure 3

the bilge or to a drain fitting.

•

Thru-Bolt Flush Cleat

Machine Screws

OPTIONAL WATER RECEPTACLE INSTALLATION. (Water receptacle sold separately.)

If using the water receptacle on:

Thru-Bolt Version

The same cut-out can be used when the cleat is mounted with the receptacle.

1. Place water receptacle on underside of cleat and attach per flush cleat installation

2. Connect 3/8" inner diameter hose to the fitting on the receptacle. Route the hose into instructions (Figure 3). The screws used must be long enough to go through the flange

of the cleat, deck, mounting plate and then the water receptacle.

1016 N. Monroe Street, Lowell, MI 49331-0260 www.attwoodmarine.com

you may have other rights which vary from state to state.

If Attwood is unable to replace the product and repair is not commercially practical or

cannot be timely made, or if the original consumer purchaser is willing to accept a refund

in lieu of repair or replacement, Attwood may refund the purchase price, less an amount

for depreciation. The acceptance by Attwood of any product returned or any refund

provided by Attwood shall not be deemed an admission that the product is defective

or in violation of any warranty. Products that are replaced or for which a refund is

issued become the property of Attwood.

THIS WARRANTY IS ATTWOOD’S ONLY EXPRESS WARRANTY OF THIS PRODUCT.

NO IMPLIED WARRANTY SHALL EXTEND BEYOND ONE (1) YEAR FROM THE DATE

OF ORIGINAL CONSUMER PURCHASE. ATTWOOD SHALL NOT BE LIABLE FOR ANY

DAMAGES FOR LOSS OF USE OF THIS PRODUCT, NOR FOR ANY OTHER

INCIDENTAL OR CONSEQUENTIAL DAMAGES, COSTS OR EXPENSES.

Some states do not allow limitations on how long an implied warranty lasts or the

exclusion or limitation of incidental or consequential damages, so the above limitations

and exclusions may not apply to you. This warranty gives you specific legal rights, and

MAINTENANCE

•A silicone based lubricant maybe used on cleat shafts to increase the ease of travel.

Hose Fitting

•

Self-Tapping Screws

(Sold Separately)

•

Receptacle

Water

Nut

•

Lock Washer

•

Marine Sealant

Backing Plate

•

Cut-Out Hole

Studs

Figure 4

•

Studded Flush Cleat

1. After the cleat has been installed, attach water receptacle to the backing plate using (4)

2. Connect 3/8" inner diameter hose to the fitting on the water receptacle. Route hose into

#8 self-tapping screws (Figure 4).

bilge or to a drain fitting.

Studded Version