ATTO Technology FibreBridge 2370E, FibreBridge 2390D, FibreBridge 2390R, FibreBridge 2390C, FibreBridge 2400C Installation And Operation Manual
...
ATTO FibreBridge
Installation and Operation Manual
ATTO FibreBridge 2370E
ATTO FibreBridge 2390C/R/D
ATTO FibreBridge 2400C/R/D
ATTO Technology, Inc.
155 CrossPoint Parkway
Amherst, New York 14068 USA
www.attotech.com
Tel (716) 691-1999
Fax (716) 691-9353
Sales support: sls@attotech.com
Technical support: Monday -- Friday, 8am-8pm EST
techsupp@attotech.com
©
2007 ATTO Technology, Inc. All rights reserved. All brand or product names are trademarks of their respective
holders. No part of this manual may be reproduced in any form or by any means without the express written
permission of ATTO Technology, Inc.
9/2007
........................................................................................................................................................
PRMA-0362-000
Contents
1.0 ATTO FibreBridge provides storage options ...............................1
ATTO FibreBridge 2370E features, benefits
ATTO FibreBridge 2390C/R/D features, benefits
ATTO FibreBridge 2400C/R/D features, benefits
1.1 ATTO FibreBridge 2370E .....................................................3
Board dimensions
Cooling and airflow
Power
Fibre Channel port
SCSI ports
Management access
LED indicators
1.2 ATTO FibreBridge 2390R/D .................................................5
Dimensions
Cooling and airflow
Power
Fibre Channel interface
SCSI ports
Management ports
Manual reset switch
LED indicators
1.3 ATTO FibreBridge 2390C .....................................................7
Board dimensions
Cooling and airflow
Power
Fibre Channel port
SCSI ports
Management access
Manual reset switch
LED indicators
1.4 ATTO FibreBridge 2400R/D .................................................9
Dimensions
Cooling and airflow
Power
Fibre Channel port
SCSI ports
Management ports
Manual reset switch
LED indicators
1.5 ATTO FibreBridge 2400C .....................................................11
Board dimensions
Cooling and airflow
Power
Fibre Channel port
SCSI ports
Management access
LED indicators
2.0 Installing the FibreBridge ...............................................................13
Unpack the packing box; verify contents
Install the FibreBridge
Discover the IP address
Internet Explorer setup
Begin initial configuration
3.0 Configuring the FibreBridge ..........................................................15
Preliminary steps
Port configurations
Modify passwords
Enhance performance
3.1 Map devices ..........................................................................17
FibreBridge mapping
SCSI device mapping
Mapping devices automatically
Mapping devices manually.
Multiple Node addressing (FB2400 only)
3.2 Remote monitoring, management ......................................19
SNMP-based monitoring
Email messages provide error notification
4.0 Updating firmware ..........................................................................23
Preliminary step
Using ExpressNAV
Using FTP
Using the zModem command
5.0 Interface options .............................................................................25
Using ExpressNAV
Opening an ExpressNAV session
Optimizing ExpressNAV in Internet Explorer
Using the serial port
Using Telnet
Appendix A Cabling ...............................................................................i
SCSI port connections
Fibre Channel connections
Serial port connections
Ethernet connections
Appendix B CLI provides ASCII-based interface ................................ii
CLI error messages
CLI summary reference
Command explanations
Appendix C Standards and compliances ............................................xvii
FCC Standards: Radio and Television Interference
Canadian Standards
European Standards
Declaration of Conformity
Certification for the FibreBridge 2400 only
Appendix D Warranty information ........................................................xix
Manufacturer limited warranty
1.0 ATTO FibreBridge provides storage options
The ATTO FibreBridge™
family of products provides Fibre Channel-to-SCSI bridges as embeddable
boards, stand alone enclosures that can be fitted for rack mount integration, or desktop units.
Fibre Channel is a serial communications
technology designed to transfer large amounts of
data between a variety of hardware systems over
long distances. It is a key technology for
applications that require shared, high bandwidth
access to storage.
Fibre Channel provides a logical point-to-point
serial channel for the transfer of data between a
buffer at a source device and a buffer at a
destination device. It moves buffer contents from
one port to another, without regard to the format
or meaning of the data, so different upper level
protocols are able to run over Fibre Channel
hardware.
All ATTO FibreBridge models can be used in a
SAN (Storage Area Network) to connect a variety
of Fibre Channel and SCSI devices. A SAN is a
shared storage architecture connecting computers
and storage devices for online data access. Each
connected system can directly access any attached
storage device.
The ATTO FibreBridge provides the interface
between SCSI and Fibre Channel resources in
SANs. Possible configurations depend upon your
current hardware.
ATTO FibreBridge 2370E features, benefits
The ATTO FibreBridge 2370E is a Fibre
Channel-to-SCSI bridge that offers a highperformance architecture supporting nextgeneration storage media. The FibreBridge
2370E allows users with SCSI storage to add
Fibre Channel connectivity, enabling SAN
connectivity for the storage system. With
industry-leading support for 4-Gigabit Fibre
Channel and Ultra320 SCSI, the FibreBridge
2370E provides the throughput required by
advanced storage media in an embeddable
form factor for easy integration into SCSI
devices.
• One 4-Gb Fibre Channel port which autonegotiates to 1-Gb, 2-Gb or 4-Gb Fibre Channel
• SFP Fibre Channel connector
• Support for direct connect to F-port fabric
switches, full duplex FC data transfers and FCAL, PLDA and public loop login
• Two independent Ultra320 SCSI connections
using standard 68-pin internal SCSI connectors
• Backward compatible with all single-ended SCSI
devices and previous SCSI protocols
• Manual and auto SCSI device mapping
• 200 MB/sec. maximum throughput
• ExpressNAV™ integrated management console
for remote configuration, management and
diagnostic capabilities
• Supports SCSI hard disk drives, tape drives and
CD libraries
• RoHS compliant
1
ATTO Technology Inc. FibreBridge Installation and Operation Manual
ATTO FibreBridge 2390C/R/D features, benefits
The ATTO FibreBridge 2390C/R/D is a 4-Gigabit
Fibre Channel-to-SCSI bridge configured with a
single 4-Gb Fibre Channel port and dual-stacked
Ultra320 SCSI buses featuring VHDCI interfaces.
Designed to integrate industry-leading
performance and SAN capabilities into advanced
storage solutions, the FibreBridge 2390 uses a
high performance architecture suited for tape
automation OEMs who wish to integrate high
performance LTO-3 and SDLT600 tape drives
into 4-Gb Fibre Channel SANs, as well as disk
OEMs looking to add 4-Gb Fibre Channel
connectivity to their disk storage devices.
• One 4-Gb Fibre Channel port which autonegotiates to 1-Gb, 2-Gb or 4-Gb Fibre Channel
• SFP FC connector
• Support for direct connect to F-port fabric
switches, full duplex FC data transfers and FCAL, PLDA and public look login
• Two independent Ultra320 SCSI buses
• Dual-stacked VHDCI SCSI connectors
• Backward compatible with all single-ended SCSI
devices and all previous SCSI protocols
• Manual and auto SCSI device mapping
• 215 MB/sec. maximum throughput
• ExpressNAV
for remote configuration, management and
diagnostic capabilities
• Supports SCSI hard disk drives, tape drives and
CD libraries
ATTO FibreBridge 2400C/R/D features, benefits
The ATTO FibreBridge 2400C/R/D is a 4-Gigabit
Fibre Channel-to-SCSI bridge configured with
dual independent 4-Gb Fibre Channel ports and
dual-stacked Ultra320 SCSI buses featuring
VHDCI interfaces.
Designed to integrate industry-leading
performance and SAN capabilities into future
generation storage solutions, the FibreBridge
2400 uses a high performance architecture suited
for tape automation OEMs who wish to integrate
high performance LTO-3 and SDLT600 tape
drives into 4-Gb Fibre Channel SANs, as well as
disk OEMs looking to add 4-Gb Fibre Channel
connectivity to their disk storage devices.
• Two independent 4-Gb Fibre Channel ports
which auto-negotiate to 1-Gb, 2-Gb or 4-Gb
Fibre Channel
• SFP FC connectors
• Support for direct connect to F-port fabric
switches, full duplex FC data transfers and FCAL, PLDA and public look login
• Two independent Ultra320 SCSI buses
• Dual-stacked VHDCI SCSI connectors
• Backward compatible with all single-ended SCSI
devices and all previous SCSI protocols
• Manual and auto SCSI device mapping
• 440 MB/sec. maximum throughput
• ExpressNAV
for remote configuration, management and
diagnostic capabilities
• Supports SCSI hard disk drives, tape drives and
CD libraries
integrated management console
integrated management console
2
1.1 ATTO FibreBridge 2370E
The ATTO FibreBridge 2370E is a 4-Gigabit Fibre Channel to SCSI bridge offering the ability to add
4-Gigabit Fibre Channel connectivity to Ultra320 SCSI devices.
The FibreBridge 2370E is available in an
embeddable card for easy integration into storage
devices.
Default values are appropriate for most applications.
Refer to
Configuring the FibreBridge
on page 15
for more information.
Board dimensions
Width:
Length:
Height of tallest component:
3.9 inches
7.995 inches
.55 inches on top,
0.1 inches on bottom
Cooling and airflow
Operating temperature:
Humidity:
10-90% non-condensing
0-40 °C
Power
The FibreBridge board
is powered from a
4-pin power connector
+12V GND GND +5V
standard 4-pin disk
drive power connector.
Input voltage and
power draw:
5.0V = 10 Watts, 12V = 24 Watts
421 3
Fibre Channel port
The 4-Gb Fibre Channel port uses a Small
Formfactor Pluggable (SFP) interface. Its rate is
set to automatic detection by default.
SCSI ports
The two independent SCSI ports are Ultra320
SCSI busses with internal HD68 connectors,
downward compatible with all forms of singleended SCSI and all previous SCSI protocols.
Management access
The 10/100 Base T Ethernet port is accessible
from the RJ-45 connector to provide local and
remote diagnostics, monitoring and management.
A serial 10-pin
header provides
support for an RS232 remote
monitoring and
management port
through the
Command Line Interface. The baud rate is
programmable and preset at the factory to 115200
bps.
LED indicators
On-board LED indicators are on the board front or
LED headers may be connected to outside panels.
SCSI ports:
a green LED indicates activity if it is
lit, no activity if it is off.
Fibre Channel port:
A green LED indicates
activity if it is lit, no activity if it is off. A separate
green LED indicates speed: you may set the LED
to signify 1 Gb/sec or 2 Gb/sec if it is off or 4
Gb/sec or 2 Gb/sec if it is on. Refer to
FCSpeedLED2G (FB2370E)
on page ix of the
Appendix.
A Ready LED
lights green to indicate ready and is
off to indicate not ready.
A Power Status LED
is on to indicate 5V and 12V
are applied to the board; flashing green indicates
that 12V is applied but 5V is not.
A Yellow LED indicates fault status:
off means
not faulted; on means faulted status.
Embedded in the Ethernet port connector:
a
lighted green LED shows a valid link; off
indicates that no link is present. A separate
blinking yellow LED indicates activity.
3
ATTO Technology Inc. FibreBridge Installation and Operation Manual
LED Header P5 Pins LED Header P6 Pins
2
4
6
8
7
5
3
1
1
3
1 Ready LED Cathode
2VDD 3.3
3 Power OK LED Cathode
4VDD 3.3
5 Fault LED Cathode
6VDD 3.3
7NC
8NC
7
5
Exhibit 1.1-1 FibreBridge 2370E board layout
8
6
1 SCSI Port 1 Activity LED Cathode
2VDD 3.3
3 SCSI Port 2 Activity LED Cathode
4VDD 3.3
5 Fibre Channel Port Speed LED Cathode
6VDD 3.3
7 Fibre Channel Port Activity LED Cathode
8VDD 3.3
2
4
4
1.2 ATTO FibreBridge 2390R/D
The ATTO FibreBridge 2390R/D is a 4-Gigabit Fibre Channel to SCSI bridge offering the ability to add 4-Gigabit
Fibre Channel connectivity to Ultra320 SCSI devices.
The FibreBridge 2390R/D is available in an industrystandard IU form factor for easy integration into racks.
The advanced connectivity options make it suitable to
support next-generation storage media such as LTO-3
and SDLT600.
Default values are appropriate for most applications.
Refer to
Configuring the FibreBridge
on page 15
for more information.
Dimensions
Width:
Length:
Height:
Weight:
16.494 inches
10 inches
1.579 inches (1U)
approximately 10 pounds
Cooling and airflow
Operating temperature:
Humidity:
10-90% non-condensing
Air enters from the front and is exhausted out the
connector side. Ambient air near the inlets should not
exceed 40 °C. The unit automatically stops operation
if the temperature goes beyond this threshold.
CAUTIONCAUTION
Do not block the enclosure’s vents. The
FibreBridge does not allow data transfer if
overheating occurs.
0-40 °C external
Power
The power supply circuit is permanently mounted
within the enclosure and is not hot swappable. It has
one standard IEC320 power receptacle and switch.
The universal power supply provides power for the
bridge board and cooling fan.
The power requirements of the ATTO FibreBridge
2390R plus the power draw of the other equipment in
the rack must not overload the supply circuit and/or
wiring of the rack.
Input voltage:
range of 90-132V AC or 175-264V AC, 100-240
VAC; 1.7-.7A, 50-60Hz.
110/230V AC, with operating input
Battery-backed event log SRAM & Real-TimeClock:
A rechargeable Lithium ion battery cell holds
the memory in a 512KB SRAM for up to 30 days.
WARNING
WARNING
Risk of explosion if the battery is removed
and/or replaced by an incorrect type.
Dispose of used batteries in accordance
with your local environmental regulations.
Explosionsgefahr, wenn die Batterie falsch
entfernt und/oder ersetzt wird. Entsorgen
Sie benutzte Batterien in Übereinstimmung
mit Ihren lokalen
Umweltschutzbestimmungen.
If the FibreBridge becomes disconnected from power,
recharging begins automatically when power is
restored to the system. The battery is fully charged
after 24 hours of continuous power application.
Fibre Channel interface
The optical SFP 4-Gb Fibre Channel port autonegotiates to 1-Gb, 2-Gb or 4-Gb devices.
SCSI ports
The two independent SCSI ports are Ultra320 SCSI
busses with VHDCI connector, downward compatible
with all forms of single-ended SCSI and all previous
SCSI protocols.
Management ports
The 10/100 Base T Ethernet port is accessible from the
RJ-45 connector to support local and remote
diagnostics, monitoring and management.
The RS-232 serial port provides
support for remote monitoring
and management using a DB9
connector. The baud rate is
programmable and preset at the
factory to 115200 bps.
RX
TX
GND
1
2
3
4
5
6
7
8
9
5
ATTO Technology Inc. FibreBridge Installation and Operation Manual
Manual reset switch
A manual reset switch reboots the FibreBridge.
To reset the FibreBridge, depress the reset button
for no more than three seconds.
To restore factory defaults, press the reset button
for more than four seconds until the green
Ready
LED blinks.
LED indicators
The LED indicators can be viewed from the connector
(back) side and the front side of the FibreBridge
2390R/D. (See Exhibit 1.2-1)
LEDs on the connector (back) side are:
A bicolor Ready/Fault LED
ready, lights yellow to show a faulted condition, and is
off to indicate not ready.
Embedded in the Ethernet port connector:
lights green to indicate
a
that no link is present. A separate blinking yellow LED
indicates activity.
Fibre Channel port:
A lighted green LED indicates
link; off means no link. A separate green LED
indicates activity if it is lit, no activity if it is off.
SCSI ports:
activity if is lit.
A green LED on each port indicates
LEDs on the front panel are:
A bicolor Ready/Fault LED
is lighted green to
indicate ready, lighted yellow to show a faulted
condition, and off indicates not ready.
SCSI ports:
A green LED on each port indicates
activity if is lit.
Fibre Channel port:
bicolor LED indicates FC
speed. If it is off, speed is 1-Gb; if it is green, 2-Gb,
and yellow indicates 4-Gb FC. A separate green LED
indicates activity if it is lit, no activity if it is off.
lighted green LED shows a valid link; off indicates
Exhibit 1.2-1 Fibre Bridge 2390R/D dimensions with front panel LEDs and connector side details
Ready, Fault LEDs
Serial port
Ethernet port Fibre Channel port
Reset switch
FC Activity, Link LE Ds
SCSI Activity LEDs
SCSI ports Power receptacle
6
1.3 ATTO FibreBridge 2390C
The ATTO FibreBridge 2390C is a 4-Gigabit Fibre Channel to SCSI bridge offering the ability to add 4-Gigabit
Fibre Channel connectivity to Ultra320 SCSI storage devices.
The FibreBridge 23900C is available in an industrystandard 4U cPCI card. Default values are appropriate
for most applications. Refer to
FibreBridge
on page 15 for more information.
Configuring the
Board dimensions
Width:
Length:
Height of tallest component:
6.1939 inches
6.299 inches
.545 inches
Cooling and airflow
Operating temperature: 0-40 °C
Humidity: 10-90% non-condensing
Power
The FibreBridge
board may be
powered from the
cPCI backplane
connector or a 6-pin connector.
Input voltage:
Power draw:
Battery-backed event log SRAM & Real-Time-
Clock:
A rechargeable Lithium ion battery cell holds
the memory in a 512KB SRAM for up to 30 days.
5.0V
30 Watts
6-pin connection pinouts
NU 5V GND 5V 5V GND
4 521 3 6
Fibre Channel port
The 4-Gb Fibre Channel port uses a Small Formfactor
Pluggable (SFP) interface.
SCSI ports
The two SCSI ports connect storage devices into the
Fibre Channel Storage Area Network (SAN). Each
port is totally independent from the other.
The ports are Ultra320 SCSI busses with VHDCI
connectors, downward compatible with all forms of
single-ended SCSI and all previous SCSI protocols.
Management access
The 10/100 Base T Ethernet port is accessible from the
RJ-45 connector to support local and remote
diagnostics, monitoring and management.
A serial 10-pin
header provides
support for an RS232 remote
monitoring and
management port
through a Command
Line Interface. The baud rate is programmable and
preset at the factory to 115200 bps.
WARNING
WARNING
Risk of explosion if the battery is removed
and/or replaced by an incorrect type.
Dispose of used batteries in accordance
with your local environmental regulations.
Explosionsgefahr, wenn die Batterie falsch
entfernt und/oder ersetzt wird. Entsorgen
Sie benutzte Batterien in Übereinstimmung
mit Ihren lokalen
Umweltschutzbestimmungen.
If the FibreBridge becomes disconnected from power,
recharging begins automatically when power is
restored to the system. The battery is fully charged
after 24 hours of continuous power application.
7
ATTO Technology Inc. FibreBridge Installation and Operation Manual
Manual reset switch
A manual reset switch reboots the FibreBridge.
To reset the FibreBridge, depress the reset button for
no more than three seconds.
To restore factory defaults, press the reset button for
more than four seconds until the green
Ready
LED
blinks.
LED indicators
The on-board LED indicators show through the
faceplate and follow left to right.
SCSI ports:
no activity if it is off.
Fibre Channel port:
link; off means no link. A separate green LED
indicates activity if it is lit, no activity if it is off.
a green LED indicates activity if it is lit,
A lighted green LED indicates
Embedded in the Ethernet port connector:
a
lighted green LED shows a valid link; off indicates
that no link is present. A separate blinking yellow LED
indicates activity.
Exhibit 1.3-1 The FibreBridge 2390C connectors and LEDS.
Exhibit 1.3-2 The FibreBridge 2390C board layout.
A bicolor Ready/Fault LED
lights green to indicate
ready, lights yellow to show a faulted condition, and is
off to indicate not ready.FibreBridge 2400C bracket
detail and board layout
8
1.4 ATTO FibreBridge 2400R/D
The ATTO FibreBridge 2400R/D is a high performance bridge adding 4-Gigabit Fibre Channel connectivity to
legacy SCSI storage devices.
The FibreBridge 2400R/D is available in an industrystandard 1U form factor for easy integration into racks.
Default values are appropriate for most applications.
Refer to
Configuring the FibreBridge
on page 15
for more information.
Dimensions
Width:
Length:
Height:
Weight:
17 inches
11 inches
1.7 inches (1U)
approximately 10 pounds
Cooling and airflow
Operating temperature:
Humidity:
10-90% non-condensing
Air enters from the front and is exhausted out the
connector side. Ambient air near the inlets should not
exceed 40°C. The unit automatically stops operation if
the temperature goes beyond this threshold.
CAUTIONCAUTION
Do not block the enclosure’s vents. The
FibreBridge does not allow data transfer if
overheating occurs.
0-40 °C external
Power
The power supply circuit is permanently mounted
within the enclosure and is not hot swappable. It has
one standard IEC320 power receptacle and switch.
The universal power supply provides power for the
bridge board and cooling fan.
The power requirements of the ATTO FibreBridge
2400R plus the power draw of the other equipment in
the rack must not overload the supply circuit and/or
wiring of the rack.
Input voltage:
100-240 VAC; 1.7-.7A; 50-
60Hz.
Battery-backed event log SRAM & Real-TimeClock:
the memory in a 512KB SRAM for up to 30 days.
A rechargeable Lithium ion battery cell holds
WARNING
WARNING
Risk of explosion if the battery is removed
and/or replaced by an incorrect type.
Dispose of used batteries in accordance
with your local environmental regulations.
Explosionsgefahr, wenn die Batterie falsch
entfernt und/oder ersetzt wird. Entsorgen
Sie benutzte Batterien in Übereinstimmung
mit Ihren lokalen
Umweltschutzbestimmungen.
If the FibreBridge becomes disconnected from power,
recharging begins automatically when power is
restored to the system. The battery is fully charged
after 24 hours of continuous power application.
Fibre Channel port
The dual independent 4-Gigabit Fibre Channel ports
can connect the FibreBridge to either a Fabric or
Arbitrated Loop using a Small Formfactor Pluggable
(SFP) interface. The FibreBridge 2400R/D auto
negotiates with 1-Gb, 2-Gb and 4-Gb/sec. devices
SCSI ports
The two SCSI ports connect storage devices into the
Fibre Channel Storage Area Network (SAN). Each
port is totally independent from the other.
The ports are Ultra320 SCSI busses with VHDCI
connector, downward compatible with all forms of
single-ended SCSI and all previous SCSI protocols.
Management ports
The 10/100 Base T Ethernet port is accessible from the
RJ45 connector to support local and remote
diagnostics, monitoring and management.
The RS-232 serial port provides
support for remote monitoring
and management using a DB9
connector. The baud rate is
programmable and preset at the
factory to 115200 bps.
RX
TX
GND
1
2
3
4
5
6
7
8
9
9
ATTO Technology Inc. FibreBridge Installation and Operation Manual
Manual reset switch
A manual reset switch reboots the FibreBridge.
To reset the FibreBridge, depress the reset button for
no more than three seconds.
To restore factory defaults, press the reset button for
more than four seconds until the green Ready LED
blinks.
LED indicators
The LED indicators can be viewed from the connector
side and the front side of the FibreBridge 2400R/D.
(See Exhibit 1.4-1)
LEDs on the connector side are:
A bicolor Ready/Fault LED
ready, lights yellow to show a faulted condition, and is
off to indicate not ready.
Embedded in the Ethernet port connector:
lighted green LED shows a valid link; off indicates
lights green to indicate
a
that no link is present. A separate blinking yellow LED
indicates activity.
Fibre Channel port:
A lighted green LED indicates
link; off means no link. A separate green LED
indicates activity if it is lit, no activity if it is off.
SCSI ports:
A green LED on each port indicates
activity if is lit.
LEDs on the faceplate are:
A bicolor Ready/Fault LED
is lighted green to
indicate ready, lighted yellow to show a faulted
condition, and off indicates not ready.
SCSI ports:
A green LED on each port indicates
activity if is lit.
Fibre Channel port:
bicolor LED indicates FC
speed. If it is off, speed is 1-Gb; if it is green, 2-Gb,
and yellow indicates 4-Gb FC. A separate green LED
indicates activity if it is lit, no activity if it is off.
Exhibit 1.4-1 Connectors, LEDs and power receptacle
air vents
Serial port
Ready/Fault LED
Reset switch
FC activity & link LEDs
Ethernet port
Fibre Channel ports
on the connector side and LEDs on the faceplate
SCSI activity LEDs
Power receptacle
SCSI ports
10
1.5 ATTO FibreBridge 2400C
The ATTO FibreBridge 2400C is a high performance bridge adding 4-Gigabit Fibre Channel connectivity to
legacy SCSI storage devices.
The FibreBridge 2400C is available in an industrystandard 4U cPCI card for easy integration into storage
devices. Default values are appropriate for most
applications. Refer to
Configuring the FibreBridge
on page 15 for more information.
Board dimensions
Width:
Length:
Height of tallest component:
6.1939 inches
6.299 inches
.545 inches
Cooling and airflow
Operating temperature: 0-40 °C
Humidity: 10-90% non-condensing
6-pin connection pinouts
Power
The FibreBridge
board may be
powered from the
cPCI backplane connector or a 6-pin connector.
Input voltage:
Power draw:
Battery-backed event log SRAM & Real-Time-
Clock:
the memory in a 512KB SRAM for up to 30 days.
If the FibreBridge becomes disconnected from power,
recharging begins automatically when power is
restored to the system. The battery is fully charged
after 24 hours of continuous power application.
11
ATTO Technology Inc. FibreBridge Installation and Operation Manual
A rechargeable Lithium ion battery cell holds
WARNING
WARNING
Risk of explosion if the battery is removed
and/or replaced by an incorrect type.
Dispose of used batteries in accordance
with your local environmental regulations.
Explosionsgefahr, wenn die Batterie falsch
entfernt und/oder ersetzt wird. Entsorgen
Sie benutzte Batterien in Übereinstimmung
mit Ihren lokalen
Umweltschutzbestimmungen.
NU 5V GND 5V 5V GND
4 521 3 6
5.0V
30 Watts
Fibre Channel port
The dual independent 4-Gb Fibre Channel ports can
connect the FibreBridge to either a Fabric or
Arbitrated Loop using a Small Formfactor Pluggable
(SFP) interface. The FibreBridge auto negotiates with
1-Gb, 2-Gb and 4-Gb/sec. devices
SCSI ports
The two SCSI ports connect storage devices into the
Fibre Channel Storage Area Network (SAN). Each
port is totally independent from the other.
The ports are Ultra320 SCSI busses with VHDCI
connectors, downward compatible with all forms of
single-ended SCSI and all previous SCSI protocols.
Management access
The 10/100 Base T Ethernet port is accessible from the
RJ-45 connector to support local and remote
diagnostics, monitoring and management.
A serial 10-pin
header provides
support for an RS232 remote
monitoring and
management port
through a Command
Line Interface. The baud rate is programmable and
preset at the factory to 115200 bps.
LED indicators
The on-board LED indicators show through the
faceplate and follow left to right.
SCSI ports:
no activity if it is off.
Fibre Channel port:
link; off means no link. A separate green LED
indicates activity if it is lit, no activity if it is off.
Embedded in the Ethernet port connector:
lighted green LED shows a valid link; off indicates
that no link is present. A separate blinking yellow LED
indicates activity.
A bicolor Ready/Fault LED
ready, lights yellow to show a faulted condition, and is
off to indicate not ready.
a green LED indicates activity if it is lit,
A lighted green LED indicates
a
lights green to indicate
Loading...