How it Works
ATTO Technology
Loading...
2400C

ATTO Technology 2390R, 2390C, 2390D, 2400C, 2400R Installation And Operation Manual

...
ATTO FibreBridge
Installation and Operation Manual
ATTO FibreBridge 2370E
Embedded 4-Gigabit Fibre Channel to SCSI bridge
ATTO FibreBridge 2390C/R/D
Multiple form factor 4-Gigabit Fibre Channel to SCSI bridge
ATTO FibreBridge 2400C/R/D
Multiple form factor 4-Gigabit Fibre Channel to SCSI bridge
ATTO Technology, Inc.
www.attotech.com
Tel (716) 691-1999 Fax (716) 691-9353
Sales support: sls@attotech.com Technical support: Monday -- Friday, 8am-8pm EST
techsupp@attotech.com
©
2008 ATTO Technology, Inc. All rights reserved. All brand or product names are trademarks of their respective holders. No part of this manual may be reproduced in any form or by any means without the express written permission of ATTO Technology, Inc.
5/2008
........................................................................................................................................................
PRMA-0362-000
ii
Contents
1.0 ATTO FibreBridge Provides Storage Options .............................................1
ATTO FibreBridge 2370E features, benefits ATTO FibreBridge 2390C/R/D features, benefits ATTO FibreBridge 2400C/R/D features, benefits
1.1 ATTO FibreBridge 2370E Physical Attributes ..................................3
Board dimensions Cooling and airflow Power Fibre Channel port SCSI ports Management access LED indicators
1.2 ATTO FibreBridge 2390R/D Physical Attributes ..............................5
Dimensions Cooling and airflow Power Fibre Channel interface SCSI ports Management ports Manual reset switch LED indicators
1.3 ATTO FibreBridge 2390C Physical Attributes ..................................7
Board dimensions Cooling and airflow Power Fibre Channel port SCSI ports Management access Manual reset switch LED indicators
1.4 ATTO FibreBridge 2400R/D Physical Attributes ..............................9
Dimensions Cooling and airflow Power Fibre Channel port SCSI ports Management ports Manual reset switch LED indicators
1.5 ATTO FibreBridge 2400C Physical Attributes ..................................11
Board dimensions Cooling and airflow Power Fibre Channel port SCSI ports Management access LED indicators
2.0 Install the FibreBridge ...................................................................................13
Unpack the packing box; verify contents Install the FibreBridge Discover the IP address Internet Explorer setup Begin initial configuration
3.0 Configure the FibreBridge ............................................................................15
Preliminary steps Page descriptions
3.1 Map Devices ........................................................................................17
FibreBridge mapping SCSI device mapping Mapping devices automatically Mapping devices manually. Multiple Node addressing (FB2400 only)
3.2 Monitor, Manage Remotely ................................................................19
SNMP-based monitoring Email messages provide error notification
4.0 Modify System Values ...................................................................................23
Preliminary steps Modify passwords Enhance performance
5.0 Update Firmware ............................................................................................25
6.0 Interface options ............................................................................................27
Using ExpressNAV Opening an ExpressNAV session Optimizing ExpressNAV in Internet Explorer Using the serial port Using Telnet
Appendix A Cabling ..............................................................................................i
SCSI port connections Fibre Channel connections Serial port connections Ethernet connections
Appendix B CLI provides ASCII-based Interface ...............................................ii
CLI error messages CLI summary reference Command explanations
Appendix C Standards and Compliances ...........................................................xv
Appendix D Warranty Information .......................................................................xvii
Manufacturer limited warranty
1.0 ATTO FibreBridge Provides Storage Options
The ATTO FibreBridge™ family of products provides Fibre Channel-to-SCSI bridges as embeddable boards, stand alone enclosures that can be fitted for rack mount integration, or desktop units.
Fibre Channel is a serial communications technology designed to transfer large amounts of data between a variety of hardware systems over long distances. It is a key technology for applications that require shared, high bandwidth access to storage.
Fibre Channel provides a logical point-to-point serial channel for the transfer of data between a buffer at a source device and a buffer at a destination device. It moves buffer contents from one port to another, without regard to the format or meaning of the data, so different upper level protocols are able to run over Fibre Channel hardware.
ATTO FibreBridge 2370E features, benefits
All ATTO FibreBridge models can be used in a SAN (Storage Area Network) to connect a variety of Fibre Channel and SCSI devices. A SAN is a shared storage architecture connecting computers and storage devices for online data access. Each connected system can directly access any attached storage device.
The ATTO FibreBridge provides the interface between SCSI and Fibre Channel resources in SANs. Possible configurations depend upon your current hardware.
The ATTO FibreBridge 2370E is a Fibre Channel-to­SCSI bridge that offers a high-performance architecture supporting next-generation storage media. The FibreBridge 2370E allows users with SCSI storage to add Fibre Channel connectivity, enabling SAN connectivity for the storage system. With industry-leading support for 4-Gigabit Fibre Channel and Ultra320 SCSI, the FibreBridge 2370E provides the throughput required by advanced storage media in an embeddable form factor for easy integration into SCSI devices.
• One 4-Gb Fibre Channel port which auto-
negotiates to 1-Gb, 2-Gb or 4-Gb Fibre Channel
• SFP Fibre Channel connector
• Support for direct connect to F-port fabric
switches, full duplex FC data transfers and FC­AL, PLDA and public loop login
• Two independent Ultra320 SCSI connections
using standard 68-pin internal SCSI connectors
• Backward compatible with all single-ended SCSI
devices and previous SCSI protocols
• Manual and auto SCSI device mapping
• 200 MB/sec. maximum throughput
• ExpressNAV™ integrated management console for remote configuration, management and diagnostic capabilities
• Supports SCSI hard disk drives, tape drives and CD libraries
ATTO FibreBridge 2390C/R/D features, benefits
The ATTO FibreBridge 2390C/R/D is a 4-Gigabit Fibre Channel-to-SCSI bridge configured with a single 4-Gb Fibre Channel port and dual-stacked Ultra320 SCSI buses featuring VHDCI interfaces.
Designed to integrate industry-leading performance and SAN capabilities into advanced storage solutions, the FibreBridge 2390 uses a high performance
1
ATTO Technology Inc. FibreBridge Installation and Operation Manual
architecture suited for tape automation OEMs who wish to integrate high performance tape drives into 4­Gb Fibre Channel SANs, as well as disk OEMs looking to add 4-Gb Fibre Channel connectivity to their disk storage devices.
• One 4-Gb Fibre Channel port which auto­negotiates to 1-Gb, 2-Gb or 4-Gb Fibre Channel
• SFP FC connector
• Support for direct connect to F-port fabric switches, full duplex FC data transfers and FC­AL, PLDA and public look login
• Two independent Ultra320 SCSI buses
• Dual-stacked VHDCI SCSI connectors
• Backward compatible with all single-ended SCSI devices and all previous SCSI protocols
• Manual and auto SCSI device mapping
• 215 MB/sec. maximum throughput
• ExpressNAV for remote configuration, management and diagnostic capabilities
integrated management console
• Supports SCSI hard disk drives, tape drives and CD libraries
ATTO FibreBridge 2400C/R/D features, benefits
The ATTO FibreBridge 2400C/R/D is a 4-Gigabit Fibre Channel-to-SCSI bridge configured with dual independent 4-Gb Fibre Channel ports and dual­stacked Ultra320 SCSI buses featuring VHDCI interfaces.
Designed to integrate industry-leading performance and SAN capabilities into future generation storage solutions, the FibreBridge 2400 uses a high performance architecture suited for tape automation OEMs who wish to integrate high performance tape drives into 4-Gb Fibre Channel SANs, as well as disk OEMs looking to add 4-Gb Fibre Channel connectivity to their disk storage devices.
• Two independent 4-Gb Fibre Channel ports which auto-negotiate to 1-Gb, 2-Gb or 4-Gb Fibre Channel
• SFP FC connectors
• Support for direct connect to F-port fabric switches, full duplex FC data transfers and FC­AL, PLDA and public look login
• Two independent Ultra320 SCSI buses
• Dual-stacked VHDCI SCSI connectors
• Backward compatible with all single-ended SCSI devices and all previous SCSI protocols
• Manual and auto SCSI device mapping
• 440 MB/sec. maximum throughput
• ExpressNAV for remote configuration, management and diagnostic capabilities
• Supports SCSI hard disk drives, tape drives and CD libraries
integrated management console
2
1.1 ATTO FibreBridge 2370E Physical Attributes
The ATTO FibreBridge 2370E is a 4-Gigabit Fibre Channel to SCSI bridge offering the ability to add 4-Gigabit Fibre Channel connectivity to Ultra320 SCSI devices.
The FibreBridge 2370E is available in an embeddable card for easy integration into storage devices.
Board dimensions
Width: Length: Height of tallest component:
inches on bottom
3.9 inches
7.995 inches .55 inches on top, 0.1
Cooling and airflow
Operating temperature: Humidity:
10-90% non-condensing
Power
The FibreBridge board is powered from a standard 4­pin disk drive power connector.
Input voltage and power draw:
12V = 24 Watts
0-40 °C
4-pin power connector
+12V GND GND +5V
421 3
5.0V = 10 Watts,
Fibre Channel port
The 4-Gb Fibre Channel port uses a Small Form factor Pluggable (SFP) interface.
SCSI ports
The two independent SCSI ports are Ultra320 SCSI busses with internal HD68 connectors, downward compatible with all forms of single-ended SCSI and all previous SCSI protocols.
Management access
The 10/100 Base T Ethernet port is accessible from the RJ-45 connector to provide local and remote diagnostics, monitoring and management.
A serial 10-pin header provides support for an RS-232 remote monitoring and management port through the Command Line Interface. The baud rate is programmable and preset at the factory to 115200 bps.
RX TX
GND
1 2
3 4
5
6 7
8 9
SCSI ports:
a green LED indicates activity if it is lit,
no activity if it is off.
Fibre Channel port:
a green LED indicates activity if it is lit, no activity if it is off. A separate green LED indicates speed: you may set the LED to signify 1 Gb/sec or 2 Gb/sec if it is off or 4 Gb/sec or 2 Gb/sec if it is on.
A Ready LED
lights green to indicate ready and is off
to indicate not ready.
A Power Status LED
is on to indicate 5V and 12V are applied to the board; flashing green indicates that 12V is applied but 5V is not.
A Yellow LED indicates fault status:
off means not
faulted; on means faulted status.
Embedded in the Ethernet port connector:
a lighted green LED shows a valid link; off indicates that no link is present. A separate blinking yellow LED indicates activity.
LED Header P5 Pins
2
4
6
8
1
3
1 Ready LED Cathode 2VDD 3.3 3 Power OK LED Cathode 4VDD 3.3 5 Fault LED Cathode 6VDD 3.3 7NC 8NC
7
5
LED Header P6 Pins
785
634
1 SCSI Port 1 Activity LED Cathode 2 VDD 3.3 3 SCSI Port 2 Activity LED Cathode 4 VDD 3.3 5 Fibre Channel Port Speed LED Cathode 6 VDD 3.3 7 Fibre Channel Port Activity LED Cathode 8 VDD 3.3
1
2
LED indicators
On-board LED indicators are on the board front or LED headers may be connected to outside panels.
3
ATTO Technology Inc. FibreBridge Installation and Operation Manual
Exhibit 1.1-1 FibreBridge 2370E board layout
4
1.2 ATTO FibreBridge 2390R/D Physical Attributes
The ATTO FibreBridge 2390R/D is a 4-Gigabit Fibre Channel to SCSI bridge offering the ability to add 4-Gigabit Fibre Channel connectivity to Ultra320 SCSI devices.
The FibreBridge 2390R/D is available in an industry­standard IU form factor for easy integration into racks. The advanced connectivity options make it suitable to support next-generation storage media.
Dimensions
Width: Length: Height: Weight:
16.494 inches
10.000 inches
1.579 inches (1U) approximately 8 pounds
If the FibreBridge becomes disconnected from power, recharging begins automatically when power is restored to the system. The battery is fully charged after 24 hours of continuous power application.
Explosionsgefahr, wenn die Batterie falsch entfernt und/oder ersetzt wird. Entsorgen Sie benutzte Batterien in Übereinstimmung mit Ihren lokalen Umweltschutzbestimmungen.
Cooling and airflow
Operating temperature: Humidity:
10-90% non-condensing
Air enters from the front and is exhausted out the connector side. Ambient air near the inlets should not exceed 40 °C. The unit automatically stops operation if the temperature goes beyond this threshold.
CAUTIONCAUTION
Do not block the enclosure’s vents. The FibreBridge does not allow data transfer if overheating occurs.
0-40 °C external
Power
The power supply circuit is permanently mounted within the enclosure and is not hot swappable. It has one standard IEC320 power receptacle and switch.
The universal power supply provides power for the bridge board and cooling fan.
The power requirements of the ATTO FibreBridge 2390R plus the power draw of the other equipment in the rack must not overload the supply circuit and/or wiring of the rack.
Input voltage:
range of 90-132V AC or 175-264V AC, 100-240 VAC;
1.7-.7A, 50-60Hz.
Battery-backed event log SRAM & Real-Time­Clock:
a rechargeable Lithium ion battery cell holds
the memory in a 512KB SRAM for up to 30 days.
WARNING
Risk of explosion if the battery is removed and/or replaced by an incorrect type. Dispose of used batteries in accordance with your local environmental regulations.
110/230V AC, with operating input
WARNING
Fibre Channel interface
The optical SFP 4-Gb Fibre Channel port auto­negotiates to 1-Gb, 2-Gb or 4-Gb devices.
SCSI ports
The two independent SCSI ports are Ultra320 SCSI busses with VHDCI connector, downward compatible with all forms of single-ended SCSI and all previous SCSI protocols.
Management ports
The 10/100 Base T Ethernet port is accessible from the RJ-45 connector to support local and remote diagnostics, monitoring and management.
The RS-232 serial port provides support for remote monitoring and management using a DB9 connector. The baud rate is programmable and preset at the factory to 115200 bps.
RX
TX
GND
1 2
3 4
5
6 7
8 9
Manual reset switch
A manual reset switch reboots the FibreBridge. To reset the FibreBridge, depress the reset button for
no more than three seconds. To restore factory defaults, press the reset button for
more than four seconds until the green
Ready
LED
blinks.
LED indicators
The LED indicators can be viewed from the connector (back) side and the front side of the FibreBridge 2390R/D. (See Exhibit 1.2-1)
LEDs on the connector (back) side are:
5
ATTO Technology Inc. FibreBridge Installation and Operation Manual
A bicolor Ready/Fault LED
ready, lights yellow to show a faulted condition, and is off to indicate not ready.
Embedded in the Ethernet port connector:
lighted green LED shows a valid link; off indicates that no link is present. A separate blinking yellow LED indicates activity.
Fibre Channel port:
a lighted green LED indicates link; off means no link. A separate green LED indicates activity if it is lit, no activity if it is off.
SCSI ports:
a green LED on each port indicates
lights green to indicate
a
LEDs on the front panel are:
A bicolor Ready/Fault LED
is lighted green to indicate ready, lighted yellow to show a faulted condition, and off indicates not ready.
SCSI ports:
a green LED on each port indicates
activity if is lit.
Fibre Channel port:
bicolor LED indicates FC speed. If it is off, speed is 1-Gb; if it is green, 2-Gb, and yellow indicates 4-Gb FC. A separate green LED indicates activity if it is lit, no activity if it is off.
activity if is lit.
Exhibit 1.2-1 FibreBridge 2390R/D dimensions with front panel LEDs and connector side details
Ready, Fault LEDs
Serial port
Ethernet port Fibre Channel port
Reset switch
FC Activ ity, Link LEDs
SCSI Activity LEDs
SCSI ports Power receptacle
6
1.3 ATTO FibreBridge 2390C Physical Attributes
The ATTO FibreBridge 2390C is a 4-Gigabit Fibre Channel to SCSI bridge offering the ability to add 4-Gigabit Fibre Channel connectivity to Ultra320 SCSI storage devices.
The FibreBridge 23900C is available in an industry­standard 4U cPCI card.
Board dimensions
Width: Length: Height of tallest component:
6.1939 inches
6.299 inches .545 inches
Cooling and airflow
Operating temperature: Humidity:
10-90% non-condensing
0-40 °C
Power
The FibreBridge board may be powered from the cPCI backplane connector or a 6­pin connector.
Input voltage: Power draw: Battery-backed event log SRAM & Real-Time-
Clock:
the memory in a 512KB SRAM for up to 30 days.
If the FibreBridge becomes disconnected from power, recharging begins automatically when power is restored to the system. The battery is fully charged after 24 hours of continuous power application.
a rechargeable Lithium ion battery cell holds
WARNING
Risk of explosion if the battery is removed and/or replaced by an incorrect type. Dispose of used batteries in accordance with your local environmental regulations.
Explosionsgefahr, wenn die Batterie falsch entfernt und/oder ersetzt wird. Entsorgen Sie benutzte Batterien in Übereinstimmung mit Ihren lokalen Umweltschutzbestimmungen.
5.0V
30 Watts
WARNING
6-pi n connecti on pinouts
NU 5V GND 5V 5V GND
4 521 3 6
Fibre Channel port
The 4-Gb Fibre Channel port uses a Small Formfactor Pluggable (SFP) interface.
SCSI ports
The two SCSI ports connect storage devices into the Fibre Channel Storage Area Network (SAN). Each port is totally independent from the other.
The ports are Ultra320 SCSI busses with VHDCI connectors, downward compatible with all forms of single-ended SCSI and all previous SCSI protocols.
Management access
The 10/100 Base T Ethernet port is accessible from the RJ-45 connector to support local and remote diagnostics, monitoring and management.
A serial 10-pin header provides support for an RS-232 remote monitoring and management port through a Command Line Interface. The baud rate is programmable and preset at the factory to 115200 bps.
Manual reset switch
A manual reset switch reboots the FibreBridge. To reset the FibreBridge, depress the reset button for
no more than three seconds. To restore factory defaults, press the reset button for
more than four seconds until the green blinks.
Ready
LED
LED indicators
The on-board LED indicators show through the faceplate and follow left to right.
SCSI ports:
no activity if it is off.
Fibre Channel port:
link; off means no link. A separate green LED indicates activity if it is lit, no activity if it is off.
Embedded in the Ethernet port connector:
lighted green LED shows a valid link; off indicates that
a green LED indicates activity if it is lit,
a lighted green LED indicates
a
7
ATTO Technology Inc. FibreBridge Installation and Operation Manual
no link is present. A separate blinking yellow LED indicates activity.
A bicolor Ready/Fault LED
ready, lights yellow to show a faulted condition, and is off to indicate not ready.
Exhibit 1.3-1 The FibreBridge 2390C connectors and LEDS.
Exhibit 1.3-2 The FibreBridge 2390C board layout.
lights green to indicate
8
1.4 ATTO FibreBridge 2400R/D Physical Attributes
The ATTO FibreBridge 2400R/D is a high performance bridge adding 4-Gigabit Fibre Channel connectivity to legacy SCSI storage devices.
The FibreBridge 2400R/D is available in an industry­standard 1U form factor for easy integration into racks.
Explosionsgefahr, wenn die Batterie falsch
Dimensions
Width: Length: Height: Weight:
16.494 inches
10.000 inches
1.579 inches (1U) approximately 8 pounds
Cooling and airflow
Operating temperature: Humidity:
10-90% non-condensing
Air enters from the front and is exhausted out the connector side. Ambient air near the inlets should not exceed 40°C. The unit automatically stops operation if the temperature goes beyond this threshold.
CAUTIONCAUTION
Do not block the enclosure’s vents. The FibreBridge does not allow data transfer if overheating occurs.
0-40 °C external
Power
The power supply circuit is permanently mounted within the enclosure and is not hot swappable. It has one standard IEC320 power receptacle and switch.
The universal power supply provides power for the bridge board and cooling fan.
The power requirements of the ATTO FibreBridge 2400R plus the power draw of the other equipment in the rack must not overload the supply circuit and/or wiring of the rack.
Input voltage: Battery-backed event log SRAM & Real-Time-
Clock:
a rechargeable Lithium ion battery cell holds
the memory in a 512KB SRAM for up to 30 days.
WARNING
Risk of explosion if the battery is removed and/or replaced by an incorrect type. Dispose of used batteries in accordance with your local environmental regulations.
100-240 VAC; 1.7-.7A; 50-60Hz.
WARNING
If the FibreBridge becomes disconnected from power, recharging begins automatically when power is restored to the system. The battery is fully charged after 24 hours of continuous power application.
Fibre Channel port
The dual independent 4-Gigabit Fibre Channel ports can connect the FibreBridge to either a Fabric or Arbitrated Loop using a Small Formfactor Pluggable (SFP) interface. The FibreBridge 2400R/D auto negotiates with 1-Gb, 2-Gb and 4-Gb/sec. devices
SCSI ports
The two SCSI ports connect storage devices into the Fibre Channel Storage Area Network (SAN). Each port is totally independent from the other.
The ports are Ultra320 SCSI busses with VHDCI connector, downward compatible with all forms of single-ended SCSI and all previous SCSI protocols.
Management ports
The 10/100 Base T Ethernet port is accessible from the RJ45 connector to support local and remote diagnostics, monitoring and management.
The RS-232 serial port provides support for remote monitoring and management using a DB9 connector. The baud rate is programmable and preset at the factory to 115200 bps.
Manual reset switch
A manual reset switch reboots the FibreBridge. To reset the FibreBridge, depress the reset button for
no more than three seconds. To restore factory defaults, press the reset button for
more than four seconds until the green Ready LED blinks.
entfernt und/oder ersetzt wird. Entsorgen Sie benutzte Batterien in Übereinstimmung mit Ihren lokalen Umweltschutzbestimmungen.
RX
TX
GND
1 2
3 4
5
6 7
8 9
9
ATTO Technology Inc. FibreBridge Installation and Operation Manual
LED indicators
The LED indicators can be viewed from the connector side and the front side of the FibreBridge 2400R/D. (See Exhibit 1.4-1)
LEDs on the connector side are:
A bicolor Ready/Fault LED
ready, lights yellow to show a faulted condition, and is off to indicate not ready.
Embedded in the Ethernet port connector:
lighted green LED shows a valid link; off indicates that no link is present. A separate blinking yellow LED indicates activity.
Fibre Channel port:
link; off means no link. A separate green LED indicates activity if it is lit, no activity if it is off.
a lighted green LED indicates
lights green to indicate
a
SCSI ports:
activity if is lit. LEDs on the faceplate are:
A bicolor Ready/Fault LED
indicate ready, lighted yellow to show a faulted condition, and off indicates not ready.
SCSI ports:
activity if is lit.
Fibre Channel port: a
speed. If it is off, speed is 1-Gb; if it is green, 2-Gb, and yellow indicates 4-Gb FC. A separate green LED indicates activity if it is lit, no activity if it is off.
a green LED on each port indicates
is lighted green to
a green LED on each port indicates
bicolor LED indicates FC
Exhibit 1.4-1 Connectors, LEDs and power receptacle
air vents
Serial port
Ready/Fault LED
Reset switch
FC activity & link LEDs
Ethernet port
Fibre Channel ports
SCSI activity LEDs
on the connector side and LEDs on the faceplate.
Power receptacle
SCSI ports
10
Loading...
+ 35 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use