DK
BRUGERVEJLEDNING
BEDIENUNGSANLEITUNG
USER MANUAL
MANUEL D’UTILISATEUR
BRUKERVEILEDNING
BRUKSANVISNING
KÄYTTÖOHJE
GEBRUIKERHANDLEIDING
DK - 1
CONTENTS
ElectronicAIR 17
Start-up 17
Inserting batteries in the remote control 18
Synchronisation of the remote control and receiver 18
Setting the remote control 19
Use of wood-burning stove with ElectronicAIR 21
Troubleshooting 22
GB
16 - GB
ELECTRONICAIR
ElectronicAIR is an electronic system that is programmed to regulate the combustion air in the wood-burning stove. Two
thermocouples constantly communicate with the receiver and remote control. Based on this communication, the damper opens
or closes automatically to ensure the optimal combustion during the start-up and continuous burning. The LED indicates when the
wood-burning stove automatically changes the damper’s position.
When the wood-burning stove is not in use, the damper is fully closed. When the door is opened, the door switch ensures that the
damper is fully open to create extra air when starting the re and when stoking the re.
If the batteries in the receiver or remote control become at, the wood-burning stove will continue to function. But the wood-
burning stove damper will always be fully open.
If you wish to manually regulate the damper and thus the supply of air, then set the remote control to manual.
Follow these instructions to use ElectronicAIR.
START-UP
We recommend that only alkaline batteries or equivalent high-quality batteries are used. The batteries should be replaced before
using the wood-burning stove for the rst in the year. Do not use a pointed item to remove old batteries.
Remote control
Use qty. 2 AAA batteries for the remote control.
Remote control
Receiver
Use qty. 4 AA batteries for the receiver.
The receiver is positioned in the opening behind the wood-burning stove.
Pull out the tray with the receiver to gain access to the batteries (see drawing).
Receiver
GB
A
GB - 17
INSERTING BATTERIES IN THE REMOTE CONTROL
1. First, insert new batteries in the remote control.
2. The remote control must be in the manual setting for the remote control and the receiver to synchronise. If the remote
control is in the automatic setting, set it to manual by briey pushing the ‘up’ and ‘down’ buttons at the same time.
Manual setting Automatic setting
GB
Down Up
SYNCHRONISATION OF THE REMOTE CONTROL AND RECEIVER
The remote control must now be synchronised using the wood-burning stove receiver. Procedure to synchronise the remote control
and receiver:
1. Insert batteries in the receiver.
2. The LED light in the front of the wood-burning stove should ash yellow and then light green. This means that the damper
is operating a start-up reference test. You may also hear a ‘click’ sound, which is completely normal. This process may take
up to two minutes.
3. After the test is nished, the LED light will ash red for 20 seconds. During this time, the remote control and receiver are
synchronised*. First, press the ‘up’ button and then press the ‘down’ button.
4. The LED light will briey light green when the synchronisation is complete and then go out.
NB: Whenever the batteries are changed in the receiver, synchronisation must be repeated.
*If you did not manage to synchronise the remote control and the receiver during this time, remove the batteries and then put
them back. You can then repeat the synchronisation process.
18 - GB
SETTING THE REMOTE CONTROL
The remote control can be set to display the time, temperature, etc.
To enter the manual setting menu, press the ‘up’ button and ‘down’ button at the same time for about ve seconds, until the
display changes.
NB:
• To change the setting, press the ‘up’ button (the button on the right) will change the setting.
• To move to the next menu, press the ‘down’ button (the button on the left).
• Move to the next menu within 15 seconds.
• After 15 seconds of inactivity, the programming menu will be exited.
• Settings are saved automatically.
GB
Menu 1:
Select whether you want to display the temperature in degrees Fahrenheit
or degrees Celsius.
The gure states the room temperature.
Menu 2:
Select whether you want to display the time in 24-hour or 12-hour format.
GB - 19
Menu 3:
Set the time.
First select the hours.
Menu 4:
Next, select the minutes.
GB
Menu 5:
Activate or de-activate the child lock.
Menu 6:
Settings for type of fuel: 00 wood or 01 coal.
It is very important that this setting is set to 00 (wood).
00 Setting for wood 01 Setting for coal
When you have nished with the six settings, you must wait 15 seconds for the settings to be
saved and the settings menu to be exited.
20 - GB
USE OF WOOD-BURNING STOVE WITH ELECTRONICAIR
After the remote control is synchronised and set, the wood-burning stove can be used. The wood-burning stove can be used with
automatic or manual operation.
AUTOMATIC OPERATION
If you want the damper on the wood-burning stove to be regulated automatically, you can use the remote control to set the stove
to automatic operation. Follow this guide showing how to operate a wood-burning stove with ElectronicAIR that is in automatic
operation mode.
1. First, you must ensure that the wood-burning stove has been set to automatic operation. To switch to automatic operation,
briey press the ‘up’ button and ‘down’ button at the same time. “Auto” is shown in the display.
2. Light the re in the wood-burning stove. If required, read the section “Starting the re correctly” in the user manual.
3. Let the door stay slightly open for approximately ve minutes. Next, close the door.
4. Once there is a good layer of embers, place two logs on the re.
5. ElectronicAIR regulates the actual combustion air during burning.
MANUAL OPERATION
If you wish to personally regulate the wood-burning stove, you can use the remote control to set the stove to manual operation.
Follow this guide showing how to operate a wood-burning stove with ElectronicAIR that is in manual operation mode.
1. First, you must ensure that the wood-burning stove has been set to manual operation. To switch to manual operation, briey
press the ‘up’ button and ‘down’ button at the same time. “Manual” is shown in the display.
2. Light the re in the wood-burning stove. If required, read the section “Starting the re correctly” in the user manual.
3. Let the door stay slightly open for approximately ve minutes. Next, close the door.
4. Once there is a good layer of embers, place two logs on the re.
5. Open and close the damper by using the two arrows on the remote control.
GB
NB! The LED light on the front of the wood-burning stove lights green when you open and close the
door and the damper automatically regulates up or down. In addition, the LED light lights briey
when you press the buttons on the remote control.
If the LED light lights red or yellow, then please refer to the troubleshooting section below .
GB - 21
TROUBLESHOOTING
The table below lists the most frequent causes of why the LED light is lit red or yellow.
LED light Cause Solution
The LED light ashes yellow twice
a minute.
Warning: Low battery power in the
receiver.
Replace the batteries in the receiver.
LED light is constantly lit red. Fault: The receiver has no power.
The LED light ashes yellow three
times a minute.
GB
In this situation, the damper opens
completely and stays open until the
batteries are replaced.
Warning: The door is open and the
sensor indicates the temperature is
over 50° C.
Replace the batteries in the receiver.
Close the door to the wood-burning
stove.
22 - GB
Loading...