Congratulations on your new AT&T U-verse TV Point Anywhere RF
Remote Control. The remote, with the USB converter, eliminates the
need to point your remote control at the AT&T U-verse Receiver in
order to change channels or access any of the receiver’s features. This
universal remote control allows you to control up to three additional
devices, such as a TV, DVD player, or audio device. It even has the
ability to “learn” commands from existing remote controls.
NOTE:The Point Anywhere RF Remote Control only controls the AT&T U-verse
Receiver using RF (radio frequency) technology. All other devices are controlled
with IR (infrared) signals.
FCC ID Numbers:
RF Remote Control - CAC3033
USB Converter - CAC3000
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following
two conditions:
1. This device may not cause harmful
interference, and
2. This device must accept any interference
received, including interference that may cause
undesired operation.
Privacy of communications may not be ensured
when using the AT&T U-verse
RF Remote Control.
NOTE: This equipment has been tested and
found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide
reasonable protection against harmful
interference in a residential installation. This
equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used
in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference
will not occur in a particular installation. If this
equipment does cause harmful interference
to radio and television reception, which can be
determined by turning the equipment off and
on, the user is encouraged to try and correct
the interference by one or more of the following
measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the
equipment and receiver.
3. Connect the equipment into an outlet on a
circuit different from that to which the receiver is
connected.
4. Consult the dealer or experienced radio/TV
technician for help.
Warning: Changes or modifications to this unit
not expressly approved by the party responsible
for compliance could void the user’s authority
to operate the equipment.
®
TV Point Anywhere
2
23
BLU-RAY/DVD CONT’D
Craig20831
Curtis22235, 23403, 23052, 21493
Curtis Mathes22331, 23925
Daewoo20833, 20869
Denon22258, 21634, 22748, 23851,
DigitalMax21738
Digix22464, 23850
Directed Video 20717
Disney20675, 21270, 23246
Durabrand23464
Dynex22596
Emerson20675, 22213
Fisher20670
Funai20675
Gateway21158
GE20717, 20522
General Electric 20717, 20522
GFM20675
Go Video20869, 21044, 20741, 21075,
GoldStar20741, 20869
GPX22235
Greenhill20717
Grundig20539
Harman/
Kardon
Hello Kitty20831
Hitachi20664, 20573
Hiteker20672
Initial20717
Insignia22596, 22095, 22428, 20675,
Integra22147, 21769, 21634
Irradio20646
JBL20702
JVC20623, 21164, 20867, 21602,
Kawasaki20790
20490
20744, 20833, 21158, 20717
20702, 22927, 23228, 20582,
21229
21013, 20741
22855
Kenwood20534, 20490
KLH20717, 20790
Lexicon22545
LG20741, 21602, 22135, 20869
LiteOn21738, 21158, 21416
Logitech22639
Magnavox20675, 21354, 20503, 20646,
Marantz22481, 22414, 20539, 23444
McIntosh21273
Memorex22213, 23153, 20831, 21270,
Microsoft22083, 22627, 20522
Mintek20717
NAD20741
Naxa22235
Nesa20717
New Acoustic
Dimension
Nyko22340
Ölevia22331
Onkyo22147, 21627, 22562, 20503,
Oppo22545, 21224
Panasonic21641, 20490, 23641, 21579,
Philco20675, 20790
Philips22056, 22434, 23488, 22084,
Pioneer22442, 21571, 20631, 22854,
Polaroid21013
Polk Audio20539
Presidian20675, 21738
Proceed20672
Proscan20522
RCA20522, 22919, 22213, 22587,
RE-BL22555
Rio20869
23488, 21506, 20539
22331
20741
21769
20703, 20503
20646, 21354, 20539, 21506,
20503, 20675, 21158
22847, 20142
23464, 21013, 20717, 22871,
21769, 20790
Getting started
How to activate the batteries of the
Point Anywhere RF Remote Control
Two AA size alkaline batteries have been preinstalled for
your convenience. Pull the “Remove to Operate Remote”
plastic tab on the back of the remote control straight out
with one smooth motion. The AT&T mode key will flash red
twice. If it does not light up, please open the battery door,
reinstall the batteries, and try again.
How to install the USB converter
NOTE: Make sure the receiver is powered on before testing the USB converter.
Step 1:
Remove the cover from the USB converter.
Step 2:
Plug the USB converter into the USB port on the front of
your AT&T U-verse Receiver. Your port location may differ
from the picture shown. The blue power LED on the USB
converter will light up and stay on.
Step 3:
The USB converter may be swiveled up or down for
optimum performance. Press the POWER or CH+/-
(CHANNEL UP/DOWN) keys to ensure proper operation.
NOTE: The USB converter must be installed in the front
USB port of the AT&T U-verse Receiver. It will not operate
if installed in the USB port on the back of the receiver.
3
Program your remote
Program your device using one of the methods below
• Program your remote control for popular brands
• Program your remote control using auto search
• Program your remote control using manual setup
• Program your remote control using the learning feature
Program your remote control for popular brands
Program your remote to control popular devices, including a TV, DVD, Blu-ray,
home theater receiver, or sound bar.
Ensure the protective battery strip has been removed. Make sure the device you
are programming is powered on and you can hear sound from it.
Step 1:
Find your device brand in the chart below – Note which number relates to your
brand. If your device brand is NOT shown, proceed to PROGRAM YOUR REMOTE
USING AUTO SEARCH.
DIGIT TV BRAND
1LG
2Panasonic
3Philips, Magnavox
4RCA
5Samsung
6Sanyo
7Sharp
8Sony
9Toshiba
0VIZIO
Step 2:
Enter programming mode – Press and hold the OK and
MENU keys simultaneously for three seconds until all four
mode keys flash red twice and you hear two short beeps to
confirm you are in programming mode.