Page 1
Quick Reference Guide For
Partner R3 – System Programming
System Programming – From extension 10 (MLS-12D or MLS-18D recommended) dial
Feature 00, then press the Left Intercom button 2 times to enter System Programming.
The numbers in parentheses after the program item heading are the factory default values.
To end the System Programming session dial Feature 00.
System Date (010100) System Time (0000)
Dial #101 Dial #103
Dial date (MMDDYY) Dial time (HHMM) in
24-hour format.
Recall Timer (18=450msec) Dial Mode (1)
Dial #107 Dial #201
Dial recall interval (01-80) 1=Touchtone, 2=Rotary
Each increment of 1 = 25msec
Hold Disconnect Time (1) Automatic Extension Privacy (2)
Dial #203 Dial #304
1=Long-450msec, 2=Short-50msec Dial extension (10-21)
1=Assigned, 2=Not assigned
Abbreviated Ringing (1) Outgoing Call Restriction (1)
Dial #305 Dial #401
Dial extension (10-21) Dial extension (10-21)
1=On/1 ring, 2=Off/repeated ringing 1=No restriction, 2=Inside only,
3=Local only
Outgoing Call Prefix (1) Music/Tones On Hold (2)
Dial #402 Dial #602
1=0/1 plus area code and number, 1=Tones on hold, 2=Not active,
2=Area code and number only 3=Music on hold
Note: Extension 15 is the music jack
Doorphone / Internal Hotline / Emergency Phone (2)
Dial #604
Dial extension (11-21)
1=Assigned, 2=Not assigned
System Initialization
Dial #989
Dial 25327 (CLEAR)
System returned to factory default
Page 1 of 3
Page 2
Quick Reference Guide For
Partner R3 – Centralized Programming
Centralized Programming – From extension 10 (MLS-12D or MLS-18D
recommended) dial Feature 00, press the Left Intercom button 2 times, then press the
Right Intercom button 1 time to enter Centralized Programming. The following
station features can only be changed in Centralized Programming. To program another
extension, press the Right Intercom button. Dial Feature 00 to end the programming
session.
Automatic Line Selection (Do this procedure first before programming other features)
Dial extension (10-21)
Dial **
Touch line buttons in the order of desired selection. (To select intercom dial tone, touch
the Left Intercom button first, then touch line buttons in the order of desired selection.)
Dial ** to end
Line Ringing
Dial extension (10-21)
Observe the green lights for each line assigned to the extension.
Immediate Ring = Steady light
No Ring = Fast fluttering light
Press each line button until the desired ring option is set.
Alert Extension or Emergency Phone Number (See #604 in system programming)
Dial doorphone or hotline extension (11-14,17-21, and 15 if not used for MOH)
Press leftmost autodial button on the top row
Assign either Doorphone/Alert Extension, or External Hotline per below instructions:
Doorphone/Alert Extension Emergency Phone Number
Press Left Intercom Dial outside phone number (up to
Dial alerted extension (10-21), or 7 for 20 digits)
all extensions
Page 2 of 3
Page 3
Quick Reference Guide For
Partner R3 – Auto/Speed Dialing
Auto Dial – Inside (Station DSS/BLF)
Enter Station Programming, or Centralized Programming
Press the button to be programmed
Press Left Intercom
Dial an extension (10-21), or *7 for Group Paging
Note: Dial * before the extension to make this a voice call instead of a ringing call
Auto Dial – Outside
Enter Station Programming, or Centralized Programming
Press the button to be programmed
Dial outside phone number (Up to 20 digits including special dialing characters)
System Speed Dial (Note: NOT Done In System Programming)
At extension 10, dial Feature 00
Press Feature followed by a 2-digit speed dial code (20-79)
Dial phone number (Up to 20 digits including special dialing characters)
Dial Feature 00 to end
Special Dialing Characters
Pause = Press Hold
Recall (Flash) = Press Spkr
Stop = Press Mic
Touchtone Enable = Press Transfer
J & J Communications
770-795-5462 or 888-552-6665
www.jandjcommunications.com
Page 3 of 3
Loading...