AT&T Partner Plus R3-1 Programming and Use

Download

AT&T

PARTNER® Plus

Communications System

Release 3.1

Programming and Use

AT&T 518-455-217 Issue 1 October 1993

Notice

Every effort was made to ensure that the information in this book was complete and accurate at the time of printing. However, information is subject to change.

Federal Communications Commission (FCC) Interference Notice

This equipment has been tested and found to comply with the limits of a Class A digital device, pursuant to Part 15 of FCC rules. For additional FCC information, see Appendix C of this book.

Canadian Emissions Requirements

This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications (DOC). For additional DOC information, see Appendix C of this book.

Le present appareil numerique n’emet pas de bruits radioelectriques depassant les limites applicable aux appareils numeriques de la classe A prescrites dans le Reglement sur le brouillage radioelectrique edicte par le ministere des Communications du Canada. Vous trouverez des renseignements complémitaires à la annexe C de ce manuel.

Security

As a customer of new telecommunications equipment, you should be aware of the significant and growing problem of theft of long distance services by third parties, known commonly as “toll fraud.”

It is particularly important that you understand and take appropriate steps to deal with this crime

because under applicable tariffs, you will be responsible for payment of associated toll charges. AT&T cannot be responsible for such charges and will not make any allowance or give any credit resulting from toll fraud.

Toll fraud can occur despite the preventive efforts of network providers and equipment manufacturers. Toll fraud is a potential risk for every customer with telecommunications equipment having one or more of the following features: (1) remote access, (2) automated attendant, (3) voice mail, (4) remote administration and maintenance, and (5) call forwarding (remote). This is not a product or design defect, but a risk associated with equipment having one or more of the features described above. If your new telecommunications equipment possesses any of these features, please consult the relevant portion of your documentation for further details and specific procedures to reduce the risk of toll fraud or contact your AT&T dealer for further details.

Trademarks

Call Assistant, PARTNER MAIL, PARTNER MAIL VS, and PassageWay are trademarks of AT&T. Magic on Hold, MERLIN, MLS-34D, MLS-18D, MLS-12D, MLS-12, MLS-6, PagePac, PARTNER, and SYSTIMAX are registered trademarks of AT&T. Microsoft is a registered trademark and Windows is a trademark of Microsoft Corporation.

Warranty

AT&T provides a limited warranty to this product. Refer to “AT&T Limited Warranty and Limitation of Liability” in Appendix B of this book.

Ordering Information

The order number for this book is 518-455-217. To order additional books, call 1 800 432-6600 in the continental U.S. and 1 800 255-1242 in Canada. For information about ordering other system reference materials, replacement parts, accessories, and other compatible equipment, refer to “Product Ordering Information” in Appendix B.

Support Telephone Number

In the continental U.S., AT&T provides a toll-free customer helpline 24 hours a day. Call the AT&T Helpline at 1 800 628-2888 if you need assistance when programming or using your system.

Outside the continental U.S., contact your local AT&T Authorized Dealer.

Contents

About This Guide

Overview

Important Safety Instructions

■

Features and Capabilities

■

System Components Auxiliary Equipment

■

Programming

■

Overview

■

Hardware Considerations

■

Initial System Setup

■

Changing Settings After Installation

■

Changing Settings to Support PBX or Centrex Services

System Programming Options

■

Using System Programming

■

Telephone Programming Options

■

Using Telephone Programming

1-i 1-ii 1-1 1-2 1-6

2-i 2-1 2-2 2-3 2-5

2-6 2-7 2-12 2-15 2-17

Learning About Telephones

■

System Telephones Standard Telephones

■

Combination Extensions

■

■ Using Telephones

3-i 3-1 3-7 3-10 3-11

Contents

Using Auxiliary Equipment

Overview

■

Answering Machines

■

Call Reporting Devices (SMDR)

■

Credit Card Scanners

■

Fax Machines

■

Modems

■

Night Service with Auxiliary Equipment

■

PARTNER Attendant

■

Voice Messaging Systems

■

Feature Reference

Troubleshooting

When You Need Help

■

Power Failure Operation Problems with System Phones

■

Problems with Standard Phones

■

■ Problems with Combination Extensions

■

Other Problems with Phones Problems with Standard Devices

■

System Problems

■

4-i 4-1 4-4 4-8 4-11 4-12 4-19 4-21 4-23 4-24

5-i

6-i 6-1 6-1 6-2 6-4 6-6 6-7 6-10 6-10

Specifications

Maintenance, Repair, and Ordering Information

A-1

B-1

Contents

FCC Information

D Speed Dial Form

Glossary

Index

Programming Quick References

C-1

D-1

GL-1

IN-1

Inside back cover

iii

About This Guide

Purpose

This guide is intended for the system manager. It explains what the PARTNER® Plus Communications System can do, provides instructions for programming and using the system, and tells how to get the most out of its many features and capabilities.

Terminology

Throughout this guide, the PARTNER Plus Communications System is referred to simply as the system and AT&T telephones specifically designed to work with the system are called system phones. You can also use industry-standard telephones with the system, which are referred to as standard phones in this guide. Finally, the PARTNER MAIL VS™ or PARTNER MAIL™ Voice Messaging System, which you may have connected to the system, is referred to as the

voice messaging system.

How to Use This Guide

For information on the following topics, refer to the appropriate chapter:

■

Getting Acquainted. Chapter 1 provides an overview of system features and hardware components.

■

Programming the System. You can change your system’s settings easily to accommodate new or expanding needs. Chapter 2 provides general programming information, while Chapter 5 provides detailed instructions for programming specific system features.

■

Training Co-Workers. Chapter 3 explains how system and standard phones work with the system. To help train co-workers on telephone basics, you can share this information with them.

About This Guide

■

Using Auxiliary Equipment. The system supports a wide variety of auxiliary equipment, including fax machines, modems, voice messaging systems, and call reporting devices. Chapter 4 provides advice on setting up these devices to work effectively with the system.

■

Daily Operation. Depending on how your system is set up, you may need to oversee some of the system’s daily operations. For example, you may need to turn on Night Service at the end of each day before leaving the office. Reference information on all features, including descriptions and instructions for using each feature, is provided in Chapter 5.

■

Solving Problems. Chapter 6 provides information on solving problems

if your system or telephones malfunction.

Once you are experienced with the system, use the Table of Contents or Index to locate the information you need.

Throughout this guide, feature names are printed in bold so you can easily look up the name in Chapter 5, “Feature Reference,” for additional information on the feature. For example, if you see a reference to System Date (#101), you can look it up in Chapter 5 for details.

Product Safety Statements

Product safety statements are identified in this guide by a

CAUTION:

Indicates the presence of a hazard that will or can cause minor personal

injury or property damage if the hazard is not avoided.

WARNING:

Indicates the presence of a hazard that can cause severe or fatal

personal injury if the hazard is not avoided.

How to Comment on This Guide

A feedback form is located at the end of this guide, after the appendixes. If the form is missing, send your comments and recommendations for changes to Documentation Manager, AT&T, 200 Laurel Avenue (Room 4E-409), Middletown, NJ 07748 (FAX 908 957-4009).

About This Guide

Overview

Contents

Important Safety Instructions

Features and Capabilities System Components

Control Unit

■

System Modules System Capacity

Telephones

■

System Telephones Intercom Autodialers Standard Telephones

Auxiliary Equipment

Requirements

■

Connecting Standard Devices

■

ii 1-1

1-2 1-2

1-4 1-4 1-5 1-5 1-5 1-6

1-6 1-7

1-7

1-i

Important Safety Instructions

WARNING:

The following list provides basic safety precautions that should always be followed when using your telephone equipment:

Read and understand all instructions.

Follow all warnings and instructions marked on the product. Unplug all telephone connections before cleaning. DO NOT use liquid

3. cleaners or aerosol cleaners. Use a damp cloth for cleaning.

This product should be serviced by (or taken to) a qualified repair

4. center when service or repair work is required.

DO NOT use this product near water, for example, in a wet basement

5. location

DO NOT place this product on an unstable cart, stand, or table.

6. Never push objects of any kind into slots or openings as they may

7. touch dangerous voltage points or short out parts that could result in a risk of fire or electric shock. Never spill liquid of any kind on the product.

Avoid using this telephone during an electrical storm. There may be a

8. remote risk of electric shock from lightning.

DO NOT use the telephone to report a gas leak in the vicinity of the leak.

10. The product is provided with a three-wire grounding type plug. This is a safety feature. DO NOT defeat the safety purpose of the grounding type plug. DO NOT staple or otherwise attach the AC

power supply cord to building surfaces.

CAUTION:

DO NOT block or cover the ventilation slots and openings. They prevent

the product from overheating. DO NOT place the product in a separate

enclosure unless proper ventilation is provided.

SAVE THESE INSTRUCTIONS

1-ii

Overview

Features and Capabilities

The following list provides an overview of the system’s features:

■

Full line of system phones, providing access to multiple lines from a single phone at each extension.

■

Programmable buttons on system phones, providing one-touch access to system features simply by pressing the button.

■

Intuitive operation of basic call handling capabilities including transfer, conference, and hold.

■

Intercom (inside) calling to other system extensions using an Intercom button and the two-digit number assigned to the extension. Users can either ring or voice signal an idle system phone, or use Voice Interrupt On Busy to signal another user who is active on a call.

■

Grouping of extensions for flexibility in directing and answering calls. Integrated voice messaging support with the PARTNER MAIL VS system

■

or PARTNER MAIL system, so callers can reach a desired extension or group without operator assistance and leave messages at unanswered or busy extensions.

Power failure operation with standard phones, allowing you to make and

■

receive calls during a power failure while retaining programmed equipment settings for up to four days. (An optional Uninterruptible Power Supply, or UPS, is also available to allow full equipment operation during a power failure.)

Centrex or PBX operation support—including one-touch dialing of feature

■

access codes on system phones. Flexible dialing restrictions and permissions so you can control telephone

■

activity and phone bills.

Overview

1-1

■

Special hospitality features that let Bed and Breakfast proprietors, for example, regulate phone use in guest rooms and schedule wake up calls

for guests.

■

Easy-to-use programming procedures, making it simple for you to manage your system and telephones. System display phones provide feedback during programming.

■

Two system programming extensions, allowing you to program the system from one extension without interrupting call activity at the other programming extension—usually the receptionist’s extension.

■

Modular connections to the control unit, making it easy to reconfigure your system or to add lines and/or extensions as your business grows.

■

Direct connections for industry-standard devices—including most standard phones, fax machines, answering machines, modems, and credit card scanners.

■

Optional equipment support, including doorphones, loudspeaker paging systems, music on hold*, call reporting (often referred to as Station Message Detail Recording or SMDR) devices, PARTNER Attendant, and extra alerts.

System Components

Modular hardware design makes the system easy to install and expand. Figure

1-1 shows an example of system components.

Control Unit

The control unit is the heart of the system; it includes a backplane and a cover, and it houses the system modules. All system modules slide into the backplane, which channels power to the system. The cover slides onto the front of the backplane after all the system modules have been installed.

WARNING:

There are no customer-serviceable components inside the system modules or backplane. There are hazardous voltages within that can cause severe or fatal personal injury. DO NOT OPEN THE MODULES.

If you use music-on-hold to broadcast certain copyrighted music or material, including songs or other

material from radio broadcasts, you may be required to obtain the permission of the copyright owner. One way to obtain permission is to contact ASCAP, BMI, and/or similar performing rights organizations, to obtain a license. Or, you can purchase a Magic on Hold® system from AT&T, which does not require you to obtain such a license. AT&T disclaims any liability arising out of the failure to obtain such a license, if required.

1-2

Overview

CONTROL UNIT

206 Modules

Main

Circuit Breaker

Optional/Devices

(for the control unit)

Cover

Processor Module

Outside Line Jacks

Power Indicators (LEDs)

Extension Jacks (206 modules only)

MUSIC ON HOLD Volume Adjustment Screw

MUSIC ON HOLD Jack (for RCA phono plug)

SYSTEM PHONES

MLS-34D® Phone

(with optional MLS-CA24

Intercom Autodialer)

Power Cord Receptacle

400 Modules

PAGE Jack

SMDR Jack

Outside Line Jacks

AT&T Serial

PARTNER

MAIL VS

Voice Messaging

System

AT&T Call Accounting Terminal (Basic or Plus)

AT&T Magic on Hold® deck

Optional Devices

(for extension jacks)

PARTNER MAIL Voice Messaging System

AT&T Paging

Printer

System

Standard Touch-Tone Phone

Figure 1-1.

MLS-18D® Phone

MLS-12D® Phone

MLS-6® Phone

Sample System Components

MLS-12® Phone

MLC-6 Phone

Fax Machine

Doorphone

Overview

Answering Machine

Alert

1-3

System Modules

The following system modules can be installed in your system:

■

If you are upgrading from a PARTNER system or a previous release of a PARTNER Plus system, you can still use its 200 modules, each providing two

line jacks. If you want message waiting capability on standard phones that are equipped

with message waiting lights, you must connect those phones to extension jacks on Release 3.1 (R3.1) 206 modules. Additionally, you need an R3.1 processor module.

Processor Module provides the software intelligence that controls the system’s features. It has jacks for a music-on-hold audio source, a loudspeaker paging system, and a call reporting (SMDR) device, such as a printer.

206E Module has jacks to connect a maximum of two outside telephone lines and six extensions to the system. You can connect telephones and other telecommunications devices (such as fax machines and modems) to the extension jacks (either directly or through your building’s modular wall jacks). Each 206E module has a green power indicator that shows it is receiving power. The system requires at least one 206E module.

400E Module is similar to the 206E module, but without extension jacks. It has four outside line jacks. This module is an inexpensive way to add lines when you do not need more extensions.

Hereafter, references to 206 modules include 206E and all 206 modules used

with previous releases of the product. Similarly, references to 400 modules

include 400E and all 400 modules used with previous releases of the product.

System Capacity

The combination of 206 and 400 modules installed determines the number of available lines and extensions. The system allows up to 12 lines and up to 24 extensions; however, these maximums cannot be achieved simultaneously:

■ For maximum line capacity (12 lines), install two 206 modules and two

■

400 modules. This arrangement allows up to 12 extensions. For maximum extension capacity (24 extensions), install four 206

modules. This arrangement allows up to 8 lines.

1-4

Overview

Telephones

System Telephones

This guide refers to AT&T telephones specifically designed to work with the system as system phones. These include the MLS-34D, MLS-18D, MLS-12D, MLS-12, MLS-6, and MLC-6 telephones.

System phones have several buttons in common: volume control buttons, and the



Feature

programmable buttons that can be used for outside lines, extension numbers,

outside phone numbers, or system features. Outside lines, as well as some system features, require buttons with status lights. Programmable buttons without lines assigned to them can be programmed with numbers or features, so you can use the feature or dial the number with one touch. The number in each model name indicates the number of programmable buttons with status lights plus two

If the system phone has a display, indicated by a “D” in the model name, users receive messages and prompts when making calls and programming. (More information about the display is provided in Chapter 5.) A system display phone is required for system programming. It must be as large as the largest phone in the system, because an MLS-12D or MLS-18D cannot program an MLS-34D. Similarly, an MLS-12D cannot program an MLS-18D.

Table 1-1 summarizes system phone features.



, 

Intercom

Conf



, 

Transfer

buttons.

,

and



Hold



buttons. In addition, each phone has

Table 1-1. System Phones

MLS-6

4 4

2 2 2

—

Total Number of Programmable Buttons

Line Capacity (Number of Programmable Buttons with Status Lights)

Intercom Buttons Display Speaker

Microphone

MLS-34D MLS-18D

12*

✔ ✔ ✔ ✔ ✔

12*

✔

MLS-12D MLS-12

✔ ✔ ✔ ✔

—

✔ ✔

Intercom Autodialers

The system phones at extensions 10 and 11 each support one MLS-CA24 Call Assistant™ Intercom Autodialer, which provides Auto Dial buttons for all of the extensions in your system (up to 24). The Auto Dial buttons allow users to dial and transfer calls to system extensions with one touch. The status lights for the buttons also indicate calling activity at each extension. For more information, see “Auto Dialing” in Chapter 5.

The MLS-34D has 32 programmable buttons with status lights and the MLS-18D has 16 programmable

buttons with status lights. Since the system supports a maximum of 12 lines, you can use up to 12 buttons on these phones for outside lines.

MLC-6

— — —

Overview

1-5

Standard Telephones

You can also use industry-standard single-line rotary or touch-tone telephones, including feature phones with built-in feature buttons and lights, with the system. This guide refers to such telephones as standard phones. AT&T-certified standard phones, such as the 8110 Analog Telephone, are recommended.

The following standard phones with message waiting lights are compatible with the system:

■

Single-Line Telephone with Message Waiting Light and Recall Button

(2500 YMGK) 7102 Plus Analog Voice Terminal

■

Check with your local AT&T Authorized Dealer to find out if other standard phones with message waiting lights will work.

NOTE:

For message waiting capability, you must connect standard phones with message waiting lights to Release 3.1 (R3.1) 206 modules, and equip the system with an R3.1 processor module. This message waiting capability does not apply to standard phones with neon-type message waiting lights.

Auxiliary Equipment

You can connect many types of telecommunications devices to your system without expensive adapters or additional phone lines. Many industry-standard,

single-line devices will work with the system regardless of the manufacturer:

■

Touch-tone, rotary, and cordless telephones (such as those you might

have in your home) Fax machines

■

Answering machines

■

Modems

■

Credit card scanners

■

There are several other devices that may be compatible with the system. For more information, refer to the list in Chapter 4 or contact your local AT&T Authorized Dealer. Also, see Chapter 4 for advice on setting up auxiliary equipment to work effectively with the system.

1-6

Overview

Requirements

An industry-standard device must meet the following conditions:

■

It must be non-proprietary. That is, it cannot be made specifically for use on a particular telephone system. (For example, you cannot connect an AT&T MERLIN® phone because it is specifically designed for use on a

MERLIN system.)

Its Ringer Equivalence Number (REN*) cannot be greater than 2.0. (The

■

REN is shown on a label on the device, usually on the bottom.)

■

You can connect a standard two-line device to the system, but for best

results it should be installed and used as if it were a single-line device.

Connecting Standard Devices

You can connect a standard device so that it is on an extension by itself, or so that it shares an extension with another piece of equipment (either another

standard device or a system phone) as long as the REN of the two devices together does not exceed 2.0. (System phones have 0.0 REN.) For example, you can connect a standard phone and an answering machine to the same extension. An extension with two devices connected to it is called a

combination extension. You cannot connect two system phones on one extension. The PARTNER Plus Communications System Installation guide

provides installation instructions.

REN is a measure of the power it takes to ring a phone. The typical home phone line handles 4.0–5.0 RENs;

each extension jack in your system handles up to 2.0 RENs.

Overview 1-7

Programming

Contents

Overview Hardware Considerations Initial System Setup

■ Setting the System Clock

■ Assigning Lines

■

Customizing Extensions

■

Copy Settings

Changing Settings after Installation

■ Changing the System Clock

■ Adding New Lines

Adding New Extensions

■

Swapping Extensions

Changing Settings to Support PBX or Centrex Services

Recall Setting

■

Dialing Restrictions

■ Speed Dial and Auto Dial Numbers

System Programming Options

■ Speed Dialing

■

Dialing Restrictions and Permissions

Restricting Access to Outside Lines

Controlling Calls on Outside Lines Overriding Dialing Restrictions Summary

Setting Up Groups of Extensions

■

■ Setting Up Auxiliary Equipment

■

Hospitality Features

2-1 2-2 2-3

2-3 2-3 2-4 2-4

2-5 2-5

2-5 2-5 2-5

2-6 2-6

2-7 2-7

2-7 2-7 2-8 2-8 2-9 2-10 2-10 2-11

2-i

Contents

Using System Programming

The Programming Overlays

■

Programming Mode

■

■ Changing Programming Type

Telephone Programming Options

■

Automatic Line Selection

■ Extension Name on Display

■

Line Ringing

■

Personal Speed Dialing

■

Programming Telephone Buttons

■ Programming a Receptionist’s Extension

Call Handling Options Button Programming

Using Telephone Programming

■

Telephone Models

■ Using Centralized Telephone Programming

■ Changing Programming Type

■ Using Extension Programming

2-12 2-12

2-14 2-14

2-15 2-15

2-15 2-15 2-15 2-15 2-16 2-16 2-16

2-17 2-17

2-17 2-20 2-20

2-ii

Programming

Overview

After the system hardware is installed, you can customize the system and individual telephones. This chapter explains how to use programming to accomplish that.

There are two types of programming:

■

System Programming allows you to customize the system to meet the needs of your business. When the system is first installed, it uses factory settings that reflect the most commonly used options. You can change system settings as needed.

You can perform System Programming from either extension 10 or 11. Because an extension cannot be in programming mode and handle calls at the same time, consider using extension 11 for programming. Doing so gives you the ability to program without disrupting call handling by the receptionist at extension 10.

■ Telephone Programming allows telephones to be customized to meet

individual users’ needs. Individual telephones can be programmed either from extension 10 or 11 (called Centralized Telephone Programming), or from a user’s extension using a system phone (called Extension

Programming).

A system display phone is required for System and Centralized Telephone Programming. Make sure that the programming phone is as large as the largest phone in the system, because an MLS-12D or MLS-18D cannot program an MLS-34D. Similarly, an MLS-12D cannot program an MLS-18D.

This chapter provides general information on programming procedures. When a specific feature name is referenced, it is printed in bold type. For detailed descriptions and step-by-step instructions, refer to that name in Chapter 5. (Brief summaries of all programming procedures are at the end of this book.)

Programming

2-1

Hardware Considerations

Programming procedures use line and extension numbers. The line number represents the line jack on a 206 or 400 module to which the outside line is connected. Similarly, the extension number represents the extension jack on a 206 module to which the system phone or standard device is connected.

For each 206 module, the system assigns two lines and six extensions; for each 400 module, the system assigns four lines. The system numbers lines and extensions consecutively. Figure 2-1 shows the numbering scheme for a system with maximum lines. Figure 2-2 shows the numbering scheme for a system with maximum extensions. However, your system can have any number of lines and extensions up to the maximum.

Line Jacks

Extension

Jacks

Figure 2-1.

Line Jacks

206 Modules

Maximum Lines

206 Modules 206 Modules

400 Modules

Line Jacks

2-2

Extension

Jacks

Figure 2-2. Maximum Extensions

Programming

Extension

Jacks

Initial System Setup

After the control unit is installed, you set up the system using a combination of system and telephone programming procedures. In this guide, System Programming procedures are identified by a code (# and three digits); Telephone Programming procedures are identified by the feature name only.

Use the System Planner as a guide when programming. The following sections provide an overview of the procedures you use for initial system setup. See Chapter 5 for more information on specific procedures. Other programming procedures are optional, but strongly recommended to make the most of your investment. (See “System Programming Options” and “Telephone Programming Options” later in this chapter for details.)

Setting the System Clock

After supplying power to the control unit, use the following procedures:

■

System Date (#101) to set the month and day. System Day (#102) to set the day of the week.

■

Assigning Lines

For initial setup only, use Number of Lines (#104) to specify the number of lines that will be assigned to all system extensions. Then use the following procedures as needed:

■

System Time (#103)

to set the hour and minutes.

Dial Mode (#201) to identify any rotary lines (the default for all lines is

“touch-tone”).

Line Assignment (#301) to assign lines to specific extensions (if the line

was not assigned using the Number of Lines procedure), to remove lines from some extensions, or to change the button used to pick up a line at a

specific extension.

Line Access Restriction (#302) to limit an extension’s access to a

specific line.

Line Ringing (Centralized Telephone Programming) to specify when a

line will start ringing at each extension that has the line. For additional information on line ringing options, see “Programming a Receptionist’s Extension” later in this chapter.

Automatic Line Selection (Centralized Telephone Programming) to

specify the order in which the system tries to select an available line

(intercom or outside), when a user at the extension lifts the handset or

presses

 Spkr  to make a call without first selecting a specific line button.

For extensions with standard phones, set Automatic Line Selection

to intercom first. This enables standard phones to access equipment

features, including intercom calling. When users lift the handsets on

standard phones, they hear intercom dial tone. To access an outside

line, they must dial 9.

Programming

2-3

Customizing Extensions

In addition to line assignments, the following procedures can be used to customize an extension:

■

Display Language (#303) to specify the language (English, French, or Spanish) for messages that appear on a system display phone.

Automatic Extension Privacy (#304) to prevent other extensions with

■

the same line from joining a call at the extension. This feature is also useful for extensions connected to a modem, fax, or any device whose function can be disrupted by someone trying to join it.

■

Forced Account Code Entry (#307) to prevent the extension from making an outside call until a required account code is entered. You can also use Forced Account Code List (#409) to create a list of valid account codes.

Outgoing Call Restriction (#401) to prevent the extension from making

■

certain types of outgoing calls (on all system lines).

■

Disallowed List Assignments (#405) to assign one or more Disallowed Phone Number Lists to the extension. Use Disallowed Phone Number Lists (#404) to create the lists of outside numbers that extensions cannot dial.

Allowed List Assignments (#408) to assign one or more Allowed Phone

■

Number Lists to the extension. Use Allowed Phone Number Lists (#407) to create the lists of outside numbers that otherwise-restricted extensions can dial.

“Setting Up Auxiliary Equipment” later in this chapter provides an overview of the procedures you use for setting up devices, such as hotline phones, voice messaging systems, and call reporting devices. Also, Chapter 4 provides detailed information and example applications for auxiliary equipment.

Copy Settings

The recommended way to set up your system is to program one extension for

each type of phone in the system, then use Copy Settings (#399) to program other phones of the same type. For example, you can program one MLS-12D phone and then copy its settings to any other extensions that have MLS-12D or MLS-12 phones. See “Copy Settings” in Chapter 5 for a list of the programmed

settings that are copied.

■

Pickup Group Extensions (#501), Calling Group Extensions (#502), Night Service Group Extensions (#504), and Hunt Group Extensions (#505) to place the extension in any of these groups. See “Setting Up

Groups of Extensions” later in this chapter for more information.

■

Fax Machine Extensions (#601), Doorphone Extension (#604 and #605), Doorphone Alert Extensions (#606), or AA Extensions (#607) to

identify the extension as one of these equipment types.

2-4

Programming

Changing Settings after Installation

As your business grows or changes, you will probably need to change the way your system was originally programmed. This section provides some examples and lists the procedures you would use to change settings after installation. For specific details on a procedure, refer to the procedure name in Chapter 5.

Changing the System Clock

You may need to change the system clock for daylight saving time, after a

prolonged power failure, or after a system reset. Use System Date (#101), System Day (#102), and System Time (#103) to set the current date, day, and

time.

Adding New Lines

If you add an outside line to your system, you may need to adjust some line

settings. In particular, use Dial Mode (#201) if the new line is a rotary line, Line Assignment (#301) to assign the line to specific extensions, Line Ringing (Centralized Telephone Programming) to specify when the line will start ringing

at each extension that has the line, and Line Access Restriction (#302) to limit

an extension’s access to the line. Additionally, the system automatically assigns the new line as the last line in the Automatic Line Selection sequence. If you want to change the order, use Automatic Line Selection (Centralized Telephone Programming).

IMPORTANT:

Do not use Number of Lines (#104) if you add lines to the system after initial setup, because it changes Line Access Restriction (#302), Automatic Line Selection, Line Ringing, and Hold Disconnect Time (#203) for existing lines

back to factory settings. To change line assignments without affecting other settings, use Line Assignment (#301).

Adding New Extensions

If you add an extension to your system, you can probably use Copy Settings

(#399) to copy the settings of an existing extension. If you wish to further adjust

a new extension’s settings, see “Customizing Extensions” earlier in this chapter.

Swapping Extensions

If a user changes physical locations but wants to keep the same extension number, you can make the change easily by swapping modular connections at the control unit.

For example, if the users at extensions 29 and 32 switch offices, you can disconnect the modular plug from extension jack 29 in the control unit, and reconnect it at extension jack 32. Likewise, unplug the wire that was connected to extension jack 32 and reconnect it at extension jack 29. Then, the users can take their respective phones to their new location to keep the same extension number and retain the phone’s programmed settings.

Programming

2-5

Changing Settings to Support

PBX or Centrex Services

This section applies only if you use PBX or Centrex services with your system. If

it does not apply, go to the next section, “System Programming Options.”

■

PBX services are provided by a private telephone switch.

Centrex services are provided by your local telephone company from a

■

Central Office (CO) outside your premises. These services include the Centrex lines connected to your control unit modules and some set of features—such as hold, conference, or transfer—that are available on those lines. Centrex services may be offered in your area under a different name. For specific Centrex features to be available to you, your company must subscribe to those features. For specific information on using Centrex, see the Centrex documentation provided by your local telephone company.

Some of the issues you should consider when setting up your system to work effectively behind a PBX or Centrex system are discussed below. Chapter 5 explains how to use the programming procedures discussed here.

Recall Setting

To set up your equipment to work properly with a PBX or Centrex system, first

set Recall Timer Duration (#107) to match the setting used by your PBX or Centrex system (usually 800 msec., or “32”). This setting affects the length of a Recall signal sent by the control unit to access Centrex services.

Dialing Restrictions

Outgoing Call Restriction (#401) is an equipment restriction intended to limit

an extension’s dialing to “inside calls only” (using the system phones) or to “inside and local calls only” (allowing calls within the PBX or Centrex system and local calls outside the PBX or Centrex system).

However, if users in your system use a dial-out code (9 on most PBX or Centrex

systems) before dialing numbers outside the PBX or Centrex system, the equipment will not be able to prevent toll calls for extensions restricted to “inside

and local calls only” (unless you use Disallowed Phone Number Lists to prevent dialing to specific classes of numbers).

If your PBX or Centrex system includes dialing restrictions, use those instead of the equipment restrictions. If you have PBX or Centrex dialing restrictions on a line and also program equipment restrictions, both the PBX or Centrex system and equipment restrictions apply. However, equipment dialing permissions will not override PBX or Centrex system restrictions.

Speed Dial and Auto Dial Numbers

When you program numbers outside the PBX or Centrex system as Speed Dial and Auto Dial numbers, include the PBX or Centrex system dial-out code (9 on most PBX or Centrex systems), followed by a pause, in the stored number.

 Intercom  buttons on

2-6

Programming

System Programming Options

This section discusses programming options that involve multiple procedures (such as dialing restrictions and auxiliary equipment settings), as well as features that can be used throughout your system (such as Speed Dialing). You can use a combination of programming procedures to set up your system to operate most efficiently, taking into account your company’s telephone service, personnel, and equipment, as well as the special needs of particular departments. This section lists the procedures you can use; for details on using a particular procedure, refer to the procedure name in Chapter 5.

Speed Dialing

You can program up to 60 frequently dialed phone numbers—such as suppliers, repair services, customers—so that all users in the system can dial them by pressing three buttons: two-digit code. These are called System Speed Dial Numbers.

Dialing Restrictions and Permissions

The system has several procedures for restricting telephone use, and several for overriding those restrictions. You can use any combination of these procedures to design a system that meets your needs.

When a user makes a call, the system checks the number dialed against all of the dialing restrictions that apply to the extension making the call. When the number dialed passes a restriction, it goes to the next one, if necessary. When a number violates a restriction, the call is stopped and the user hears a reorder tone (fast busy signal).



Feature



(or

 # 

on a standard phone) plus a

IMPORTANT:

While procedures that restrict dialing are very effective, absolute protection against misuse cannot be guaranteed. System phones give more protection than standard phones. Therefore, we strongly recommend that you install system phones where restricting phone use is important.

Restricting Access to Outside Lines

A user can access a line either by pressing the line button on the phone or by dialing a feature code (Direct Line Pickup). If you do not want a user to access a specific outside line, you can use Line Access Restriction (#302) to control an extension’s access to a certain line (whether the line is assigned to the extension or not). Table 2-1 provides examples of settings that can be used to restrict an extension’s access to a specific outside line.

NOTE:

If Forced Account Code Entry (#307) is programmed for an extension, that extension is required to enter an account code before dialing an outside number—even those on the the lines assigned to that extension. If Forced Account Code List (#409) contains entries, the system checks the account code against the list. If the account code is on the list, line access is allowed; if not, line access is denied.

Emergency Phone Number List (#406)

Programming

— on all of

2-7

Controlling Calls on Outside Lines

When an extension is allowed access to an outside line, you can use the

following procedures to control calling:

■

Outgoing Call Restriction (#401) defines the type of calls (inside only, local only, or inside, local, and long-distance) that users can make from

all lines available on an extension. Outgoing Call Restriction Button

(#114) allows the receptionist at extension 10 to quickly change an

extension’s current Outgoing Call Restriction setting.

■

Disallowed Phone Number Lists (#404) creates up to four lists of numbers that cannot be dialed. After creating Disallowed Phone Number Lists, use Disallowed List Assignments (#405) to assign one or more lists to a specific extension.

■

Night Service with System Password (#403) restricts users at

extensions in the Night Service group from dialing outside phone

numbers (except Emergency numbers and Marked System Speed Dial numbers) unless the password is entered first.

Table 2-2 provides examples of settings that can be used to restrict an extension’s dialing once it gets an outside line.

Overriding Dialing Restrictions

The following programming procedures provide ways to override all dialing restrictions, provided the user has access to an outside line:

■

Emergency Phone Number List (#406) defines a list of up to ten numbers that can be dialed from any extension. A typical number is 911.

■

Marked System Speed Dial Numbers are specially identified System Speed Dial numbers, which a user can dial by pressing

 Feature  (or  # 

on a standard phone) followed by a two-digit code.

■

System Password (#403) creates a password that can be entered at any system phone (except an MLC-6) to override dialing restrictions for the duration of a call.

To override all dialing restrictions except Line Access Restriction (#302) and

Night Service with System Password (#403), use Allowed Phone Number Lists (#407) to create lists of outside numbers that otherwise-restricted

extensions can dial. Then use Allowed List Assignments (#408) to assign one or more of the lists to an extension.

2-8

Programming

Summary

Tables 2-1 and 2-2 summarize the available dialing restrictions and permissions, showing how they can be combined in a variety of ways to customize an extension’s dialing privileges.

Table 2-1. Settings that Restrict an Extension’s Access to a Specific Line

Type of Restrictions or Permissions for the

Extension

Can receive and place intercom (inside) calls only

Cannot use a specific outside

Setting for Setting for Line Assignment (#301)

All outside lines* “not assigned”

Outside line “not assigned”

Line Access Restriction (#302)

“No access” for all lines

“No access” for that line

line Can only monitor call activity

Outside line “assigned”

“No access” for that line

and pick up held calls on a specific line

Can only receive calls on a

Outside line “assigned”

“Incoming only” for that line

specific line

Can only place outgoing calls on a specific line

Outside line* may be “assigned”

“Outgoing only” for that line

Table 2-2. Settings that Restrict an Extension’s Dialing Once It Gets an Outside Line

Type of Restrictions or Permissions for the Extension

Can place intercom and local calls only (and can answer

any call)

Can place

intercom, local and longdistance calls (and can answer

any call)

Setting for Line

Assignment

(#301)

Outside line* may be “assigned”

Outside line* may be

“assigned”

Setting for Line Access Restriction (#302)

“No restriction”

Setting for Outgoing Call Restriction (#401)

“Local only” Any local

“No restriction” Any local and

Setting for

Disallowed Phone Number Lists (#404)

numbers the extension should not dial

long-distance numbers the extension should

not dial

If a line is not assigned to the extension, a user can use Direct Line Pickup to access the line. Emergency

numbers, Marked System Speed Dial numbers, Allowed Phone numbers, and numbers dialed using the System Password override all dialing restrictions if a user has access to an outside line to place the call. If Forced Account Code Entry is programmed for an extension, the user must enter an account code before

accessing an outside line. If there are entries in the Forced Account Code List, the entered account code

must match an entry on that list.

Programming

2-9

Setting Up Groups of Extensions

You can set up four types of extension groups:

■

Pickup Group Extensions (#501) assigns extensions to one of four Pickup Groups. A Pickup Group lets any user in the system answer outside calls for any extension in that group.

■

Calling Group Extensions (#502) assigns extensions to one of four Calling Groups. A Calling Group lets users ring or page all extensions in that group simultaneously.

■

Night Service Group Extensions (#504) assigns extensions to the Night Service Group. When Night Service is activated at extension 10, calls ring immediately at Night Service extensions regardless of how they ring at other times (only the lines assigned to an extension will ring).

■

Hunt Group Extensions (#505) assigns extensions to one of seven Hunt Groups. (Hunt Group 7 is used exclusively for the voice messaging system.) A Hunt Group lets users ring or voice signal the first available (non-busy) extension in that group. If a ringing call is not answered, the system tries each available extension in turn until the call is answered. If a voice-signaled call is not answered, the call does not keep hunting. Also use Group Call Distribution (#206) to assign outside lines to a Hunt Group if you want outside calls to ring directly into a group.

Setting Up Auxiliary Equipment

The following programming procedures help you manage auxiliary equipment. See Chapter 4 for more information on auxiliary equipment configurations or refer to Chapter 5 for details on using the procedure:

■

Fax Machine Extensions (#601) identifies extensions to which fax machines are connected.

Music on Hold (#602) activates or deactivates the MUSIC ON HOLD jack

■

on the processor module. When this jack is activated and an audio source is connected, callers hear recorded music or messages while on hold. Also, Background Music lets users with system phones (other than the MLC-6) play the recorded material through their phone’s speaker when the phone is not in use.

Hotline (#603) identifies hotline extensions, so when a person lifts the

■

handset of the hotline phone, a predetermined extension automatically rings.

■

Doorphone Extension (#604 and #605) identifies extensions to which doorphones are connected. Doorphone Alert Extensions (#606) identifies extensions that signal when the doorphone button is pressed.

■

AA Extensions (#607) identifies extensions to which PARTNER Attendants are connected. This lets the system notify users with display phones when they are receiving a call that has been transferred from the PARTNER Attendant. Also, Transfer Return Extension (#306) lets you identify the extension to which a call transferred by the PARTNER Attendant should be routed if the destination extension does not answer.

2-10

Programming

■

SMDR Record Type (#608) specifies the type of calls that you want to record for call reporting—either all calls or outgoing calls only. Account Code Entry lets users specify account codes for outside telephone calls; if used, the account codes are included on the call report. SMDR Top of Page (#609) notifies the system that the printer has been aligned to the top of a new page.

■

The voice messaging system uses the following procedures: – Hunt Group Extensions (#505) assigns the extensions associated

with the voice messaging system hardware to Hunt Group 7—the VMS

Hunt Group. (The PARTNER MAIL VS system uses two extensions;

the PARTNER MAIL system uses two or four extensions.)

– Group Call Distribution (#206) assigns lines to the VMS Hunt Group

so calls can ring directly into the voice messaging system and receive

Automated Attendant Service or directly into the voice mailbox of a specific subscriber.

–

VMS Hunt Delay (#506) determines when outside calls should be answered by the Automated Attendant Service of the voice messaging

system. You can set the system for either immediate call handling or

delayed call handling. The setting you select is used for both day and

night operation.

–

VMS Hunt Schedule (#507) determines when outside calls should

ring the VMS Hunt Group (always, day only, or night only) depending

on the status of the Night Service Button (#503) at extension 10. Automatic VMS Cover (#310) determines whether or not an

–

extension’s unanswered intercom and transferred calls are automatically covered by the voice messaging system.

– Transfer Return Extension (#306) identifies the extension to which a

call transferred by the voice messaging system should be routed if the

destination extension does not answer and does not have voice mail

coverage active. (The transfer return extension for the voice messaging system is typically extension 10.)

Hospitality Features

The following hospitality features are for special applications, such as the Bed and Breakfast and Hotel/Motel industries:

■

Outgoing Call Restriction Button (#114) lets you program a button on the system phone at extension 10 to change an extension’s current Outgoing Call Restriction setting without entering System Programming mode. For example, after a guest’s departure, a hotel manager can change the No Restriction setting of the guest room phone to Inside Only so outside calls cannot be made from the phone after the guest checks out.

■

Wake Up Service Button (#115) lets you program a button on the system phone at extension 10 to be used for scheduling wake-up or reminder calls for specified system extensions.

Programming

2-11

Using System Programming

System Programming changes settings for the system as a whole, or for individual lines or extensions. You can also use System Programming to set up dialing restrictions, define groups, or set up auxiliary equipment. Refer to the filled-out System Planner when you are changing system settings, and be sure that any changes in programming are recorded there.

The Programming Overlays

System Programming requires a programming overlay placed over the dial pad of the MLS-34D, MLS-18D, or MLS-12D system phone at extension 10 or 11. (Overlays are provided with the system documentation. Replacements can be ordered through the AT&T Sourcebook.) Figure 2-3 illustrates the programming overlays.

During System Programming, the normal functions of several buttons on the display phone at extension 10 or 11 change. For example, the left

button becomes  System Program , the button used to enter programming mode.

The programming overlay identifies these buttons. You use the following special buttons while programming:

■

 Next Procedure  and  Prev Procedure  cycle forward and backward through

the programming procedures. You can use these buttons to select a procedure.

 Intercom 

■

 Next Item  and  Prev Item  cycle forward and backward through a

procedure’s parameters. A parameter is typically an outside line, an extension, or a telephone list entry.

■

 Next Data  and  Prev Data  cycle forward and backward through the valid

entries. These buttons work only for fixed data, such as a line or extension number. They do not work for variable data such as date, time, password, telephone numbers, or doorphone assignments.

 Remove  returns the current setting to the factory setting—or when using

■

Line Assignment (#301), removes lines from an extension.

 Enter  ends an entry of variable length, such as a telephone number in an

■

Allowed Phone Number List.



System Program

■

 Central Tel Program  starts the Centralized Telephone Programming process

■



starts the System Programming process.

(to customize individual telephones centrally from extension 10 or 11).

■



Feature



when followed by

 Wild  enters a “wildcard” (a character that matches any digit dialed) in

■

 0   0 ,

enters or exits programming mode.

telephone numbers in Allowed Phone Number Lists (#407), Disallowed Phone Number Lists (#404), and the Forced Account Code List (#409).

2-12

Programming

Figure 2-3.

MLS–34D

MLS-18D/MLS-12D

Programming Overlays for System Display Phones

Programming

2-13

Programming Mode

Place the Programming Overlay over the dial pad of the system display phone

1. at extension 10 or 11—see “The Programming Overlays” earlier in this chapter for more information.

To enter programming mode, press

PROGRAM EXT 10

If you are programming from extension 11, “11” displays instead of “10.”

Press

10 Enter name

This display is for the Extension Name Display feature. When you are entering System Programming mode, skip it by moving on to Step 4.

Press  System Program  again. The display reads:

SYSTEM PROGRAM

5. Specify a programming procedure in one of two ways:

■

Direct Method to dial the code for that procedure. System Programming procedures in this guide are identified by # and a three-digit code (for example, System Date is #101). This method is best when you are using only a few procedures during a programming session and you know the codes.

■

Cycle Method to cycle through the procedures in numerical order. Press through the programming procedures. This method is best when you are using multiple procedures during a programming session, or if you do not know the codes.



Feature

  0   0 .

The display reads:

 System Program . The display reads:

 Next Procedure  and  Prev Procedure  to cycle forward and backward

To exit programming mode, you can press

6. off-hook, then place it back in the cradle.

NOTE:

You can talk on the phone while you program. This is useful if you need to talk with someone at the AT&T Helpline about programming. However, you must

call before you enter programming mode, and you must use the handset to talk, not the speaker and microphone.

Changing Programming Type

When you are in programming mode, you can move between System

Programming and Centralized Telephone Programming. To change to

Centralized Telephone Programming when you are in System Programming,

 Central Tel Program . To move back to System Programming when you are

press in Centralized Telephone Programming, press



2-14

System Program

Programming

.



Feature

  0   0 



Central Tel Program

or lift the handset



then

Telephone Programming Options

System telephones are ready to use when they are installed, but they can be customized to meet the needs of your business and individual users. This customization is accomplished through Telephone Programming.

Automatic Line Selection

When a user lifts the telephone’s handset or presses an idle line automatically. Automatic Line Selection determines the order in which the system looks for an idle line. You can set the system to look for lines in any desired order. For standard phones or for any phone used mainly to call other extensions, select an inside (intercom) line first.

Extension Name on Display

With Extension Name Display, users can assign a name (up to 12 characters long) to their extension. Then, when those users make an intercom call, group call, or transfer a call, their name and extension number appears on the display phone receiving the call. Similarly, users receiving a transfer return call see the name and extension number of the person assigned to the extension that did not answer the transferred call.

Line Ringing

Line Ringing defines when each outside line rings at a phone. For each line at an extension, you can specify Immediate Ring, Delayed Ring (phone rings after a 20-second delay), or No Ring.

Personal Speed Dialing

Personal Speed Dial numbers are outside phone numbers that a user dials by pressing System Speed Dial numbers, which are available to all users in the system, Personal Speed Dial numbers are available only at the extension for which they

are programmed. Users can store up to 20 Personal Speed Dial numbers.

 Feature  (or  #  on a standard phone) plus a two-digit code. Unlike



Spkr

,

the system chooses

Programming Telephone Buttons

Telephone buttons without lines assigned to them can be programmed for system features such as Exclusive Hold or Conference Drop or for telephone numbers, so you can use the feature or dial the phone number with one touch. Once programmed, these buttons are called Auto Dial buttons, because simply pressing the button automatically dials the feature code or the telephone number.

A user who has a system phone with programmable buttons should consider

programming them with a combination of frequently used features and outside and intercom telephone numbers.

Programming

2-15

Programming a Receptionist’s Extension

Call Handling Options

If you set up a centralized telephone answering position at extension 10, use the

following settings to customize it:

■

Immediate Call Answering. If the receptionist should answer all calls, use Line Assignment (#301) to assign all lines to extension 10. Set Line Ringing for all lines at extension 10 to Immediate Ring; set the lines assigned at each user’s extension to Delayed Ring or No Ring.

■

Backup Call Answering. If the receptionist should answer some lines

only when a user does not pick up, set Line Ringing for those lines at extension 10 to Delayed Ring; set the lines assigned at each user’s extension to Immediate Ring.

■

No Answering. If some lines should not be picked up by the receptionist at all, either set Line Ringing for those lines at extension 10 to No Ring or simply use Line Assignment (#301) to remove those lines from extension

10. In either case, set Line Access Restriction (#302) to No Access for those lines at extension 10 to prevent the receptionist from using Direct Line Pickup to access those lines.

Button Programming

The MLS-34D phone shown in Figure 2-4 illustrates the following programmed buttons in addition to some other system features:

■

Extension Numbers. Auto Dial buttons are programmed for extensions 11 through 30, starting with the top left button shown in Figure 2-4. The receptionist can use these buttons to dial or transfer calls to the extensions with one touch. In addition, the lights of the Auto Dial button

show the status of the extension, so the receptionist can tell whether the

phone at the extension is idle (no lights on), busy (red on), calling the receptionist (green flash), or ringing back after the receptionist

transferred a call (green flutter).

■

Fax Management. A button (labeled Fax-31) is programmed as a Fax Management button for the fax machine connected to extension 31. The lights next to the button show what is happening at the fax machine (for example, red broken flutter indicates that the fax machine is not responding—like when it is out of paper). (For more information, see “Fax Management Feature” in Chapter 4.)

Alternatively, the receptionist can use an MLS-CA24 Intercom Autodialer for the

extensions the receptionist dials most frequently. This leaves buttons on the phone free for more features and phone numbers.

2-16

Programming

MLS-34D Phone

Line/ Programmable Buttons

Any unused line button is programmable

Figure 2-4.

Button Programming for Receptionist’s Phone

Using Telephone Programming

There are two ways to program a telephone: Centralized Telephone Programming from extension 10 or 11 (see below) and Extension Programming

from a user’s own extension (see page 2-20).

Telephone Models

Figure 2-5 illustrates an MLS-34D, MLS-18D, MLS-12D/MLS-12, and MLS-6 phone. As you program buttons, mark their functions on the phone’s labeling sheet (see the examples in Figure 2-5).

NOTE:

An MLS-6 phone with 4 lines assigned to it has no buttons available for programming. The MLC-6 cordless phone looks just like an MLS-6 phone when you program it centrally.

Using Centralized Telephone Programming

Use Centralized Telephone Programming to program features or store telephone numbers for individual extensions from extension 10 or 11. Most features also can be programmed on a system phone at the user’s extension.

Keep in mind the following exceptions:

■

Automatic Line Selection and Line Ringing always must be programmed using Centralized Telephone Programming.

If a user has a standard phone, Personal Speed Dial Numbers for the

■

extension can be programmed only by using Centralized Telephone Programming.

If a user has a standard phone or a non-display system phone,

■

Extension Name Display for the extension can be programmed only by using Centralized Telephone Programming.

Programming

2-17

During Centralized Telephone Programming, the display phone at extension 10

or 11 takes on the characteristics of the telephone being programmed, including

any System Programming settings and lines assigned to the phone. Make sure the programming phone is as large as the largest phone in the system, because an MLS-18D phone cannot program an MLS-34D phone and an MLS-12D phone cannot program an MLS-18D phone or an MLS-34D phone.

To program a phone from extension 10 or 11, use the following procedure:

Place the Programming Overlay over the dial pad of the system display phone

1. at extension 10 or 11—see “The Programming Overlays” earlier in this chapter for more information.

To start programming:

2. Press



Feature

  0   0 .

The display reads:

PROGRAM EXT 10

If you are programming from extension 11, “11” displays instead of “10.”

 System Program . The display reads:

Press

10 Enter name

This display is for the Extension Name Display feature. When you are entering Centralized Telephone Programming mode, skip it by moving on to Step 2c.

 System Program  again. The display reads:

Press

SYSTEM PROGRAM

Press  Central Tel Program . The display reads:

CENTRAL TEL PROG Extension:

Dial the extension number of the telephone to be programmed.

Buttons on which lines are assigned for the extension light up to show the current Line Ringing settings; remaining buttons can be programmed with telephone numbers, extension numbers, or system features.

At this point, you can:

■

Use Automatic Line Selection to change the order in which the telephone tries to select a line when the user picks up the handset. (If you want to change Automatic Line Selection for an extension, you must do so immediately after you enter programming mode and dial the extension number.)

■

Use Extension Name Display to assign a user’s name to the extension. (Like Automatic Line Selection, this procedure must be done immediately after you enter programming mode and dial the extension number. If you want to change both Automatic Line Selection and Extension Name Display, first change Automatic Line Selection, then press

 Central Tel Program  and return to Step 3, redial the extension

number, then use Extension Name Display.)

2-18

■

Programming

Use Line Ringing to change the ringing for an individual line.

MLS-34D Phone

Line/ Programmable

Buttons

Any unused line button is programmable

MLS-18D Phone

Line/ Programmable

Buttons

Any unused line button is programmable

MLS-12D/MLS-12 Phone (display on

MLS-12D only)

Programmable Buttons

(without lights)

Line/

Programmable

Buttons

Any unused line button is programmable

MLS-6 Phone

Line/ Programmable Buttons

Any unused line button is programmable

Figure 2-5. Programmable Buttons and Labeling Sheets on System Phones

Programming

2-19

Program Personal Speed Dial Numbers, Auto Dial numbers, or system

5. features as described in Chapter 5.

To erase the current programming from a button, press the button, then press



Mic

.

To change the settings for another extension, press  Central Tel Program , then

6. dial the new extension number.

To exit programming mode, you can press

7. off-hook, then place it back in the cradle.

Changing Programming Type

When you are in programming mode, you can move between System Programming and Centralized Telephone Programming. To change to System Programming when you are in Centralized Telephone Programming, press

 Central Tel Program  then  System Program . To move back to Centralized Telephone

Programming when you are in System Programming, press

Using Extension Programming

Users can program features or store numbers on buttons from their own phones using Extension Programming. Keep in mind the following exceptions:

■

Automatic Line Selection and Line Ringing always must be programmed using Centralized Telephone Programming.

■

If a user has a standard phone, Personal Speed Dial Numbers for the extension can be programmed only by using Centralized Telephone Programming.

■

If a user has a standard phone or a non-display system phone, Extension Name Display for the extension can be programmed only by using Centralized Telephone Programming.



Feature

  0   0 ,

 Central Tel Program .

or lift the handset

2-20

To program at the extension, use the following procedure:

To start programming, dial



Feature

  0   0 .

Buttons on which lines are assigned for the extension light up to show the current Line Ringing settings. Remaining buttons can be programmed

with telephone numbers, extension numbers, or system features.

To assign a name to the extension, press left

2. character codes. See Extension Name Display in Chapter 5 for the codes.

Program Personal Speed Dial Numbers, Auto Dial numbers, or system

features as described in Chapter 5. To erase the current programming from a button, press the button, then

press



Mic

.

To exit programming mode, you can press



Feature

off-hook, then place it back in the cradle.

Programming



Intercom

  0   0 ,

,

then enter the

or lift the handset

Learning About Telephones

Contents

System Telephones

■ Buttons and Indicators

■

Lights

■

Ringing Patterns

■

Dial Tones

■ Using the Handset, Speaker, and Microphone

Hands-Free Answer on Intercom (HFAI)

Voice Interrupt on Busy Calls

Speakerphone Performance Tips

Standard Telephones

■

Ringing Patterns Dial Tones

■

■ Using the Switchhook

Limitations

■

Feature Phones

Combination Extensions Using Telephones

■ Basic Call Handling Features

■ Dial-Code Features

3-1 3-2

3-4 3-5 3-5 3-5 3-6 3-7 3-7

3-7 3-8

3-9 3-9 3-9 3-10

3-10 3-11

3-11 3-12

3-i

Learning About Telephones

This chapter explains how system and standard phones work with the system, as well as combination extensions where more than one phone or standard device is installed. System phones are described first, followed by standard phones on page 3-7 and combination extensions on page 3-10. In addition, call handling features are listed on page 3-11. See the feature name in Chapter 5 for details on a specific feature.

System Telephones

System phones, which include the MLS-34D, MLS-18D, MLS-12D, MLS-12, MLS-6, and MLC-6 models, have several buttons and indicators in common. The following pages explain where they are and how they work.

Learning About Telephones

3-1

Buttons and Indicators

MLS-34D

Display

Line/Programmable

Buttons

Intercom Buttons (2)

(32 with lights)

MLS-18D

The following buttons and indicators appear on system phones:

Display.

a call, extension number (and name if programmed) calling you or transferring a call to you, and duration while a call is in progress. When programming, shows settings, options, and prompts. (To adjust the MLS-18D display contrast, see Volume

Control Buttons.) Line/Programmable Buttons. Used for outside lines or (if no line is assigned on a button) for programming telephone or

extension numbers, or other system features (such as Last Number Redial). When a line is assigned, you can press the line button to make a call on a specific line (lights show status of line). When a number or feature is programmed, you can press the button to dial the number or use the feature. The MLS-34D has 32 programmable buttons (all with lights); the MLS-18D has 16 programmable buttons (all with lights); the MLS-12D and MLS-12 have16 programmable buttons (10 with lights); the MLS-6 and MLC-6 phones have 4 programmable buttons (all with lights).

Intercom Buttons. Press to make (or answer) a call to (or from) another extension in the system. Other Buttons and Indicators (shown in exploded views)

(MLS-34D, MLS-18D, and MLS-12D only) Shows date, day, and time when phone is idle, number dialed when placing

Feature (labeled “Feat” on MLC-6). Press to change programmed settings or use system features. Conf. Press to add other parties to your call. Transfer (labeled “Trans” on MLC-6). Press to pass a call to another extension. Hold. Press to put a call on hold.

Display (not on MLS-12)

Programmable Buttons

(6 without lights)

Line/Programmable Buttons

Intercom Buttons

(2)

MLS-12D/MLS-12

3-2

Learning About Telephones

MLS-6

Line/Programmable Buttons (4)

Intercom Buttons (2)

MLC-6 (Base)

MLC-6 (Handset)

Earpiece Volume Control Switch

Handset Display

Intercom

Buttons (2)

Spkr (all models except the MLC-6). Press to turn on and off speaker and microphone (if available), so you can dial and have a conversation without lifting the handset. The light next to this button shows when the speaker is turned on.

Mic (MLS-34D, MLS-18D, MLS-12D, and MLS-12 only). Press to turn the microphone on and off. The light next to this button shows

when the microphone is turned on. Leave on to use the Hands-Free Answer on Intercom (HFAI) feature.

Message Light.

Lights when someone signals you with the Message Light On feature, or if you have a voice messaging system, when

you have a message in your mailbox.

Volume Control Buttons. (all models except the MLC-6). Press ▼ to decrease or ▲ to increase the volume as follows:

To adjust ringer volume, press ▼ or ▲ while the phone is idle and the handset is in the cradle.

■

To adjust speaker volume, press ▼ or ▲ while listening to a call through the speaker.

■

To adjust handset volume, press ▼ or ▲ while listening through the handset.

■ To adjust background music volume, press ▼ or ▲ while listening to music through the phone’s speaker.

To adjust the display contrast on the MLS-18D phone, press

 ★ 

then ▼ to decrease the brightness or ▲ to increase the brightness,

while the phone is idle and the handset is in the cradle.

On/Off Button (MLC-6 Handset). Turns the handset on and off. (You must turn the handset on to make calls.) Status Button (MLC-6 Handset). Quickly updates the display on the MLC-6 handset.

Earpiece Volume Control Switch (MLC-6 Handset). To adjust handset volume, slide switch up (high) or down (low). Talk indicator (MLC-6 Base). Lights when handset is lifted and turned on. Charge indicator (MLC-6 Base). Lights when handset is placed on the base and handset batteries are charging.

Ringer Volume Control (MLC-6 Base). To adjust volume, press ▼ or ▲ while the phone is idle.

Line/Programmable Buttons (4)

Learning About Telephones

3-3

Lights

Each line button has a green light and a red light. The meaning of these lights varies, depending on whether a button is used to access an outside line, is programmed with a system feature, or is programmed for Auto Dialing an extension number (Intercom Auto Dial button). (Auto Dial buttons for fax extensions show additional information; these “Fax Management” buttons are described in Chapter 4. When a phone is in programming mode, the lights show information about programmed settings; See Chapter 2 for details.)

Table 3-1 shows the meanings of the various light patterns for each possible

button assignment.

Table 3-1. Light Patterns for System Phones

Light Pattern

Steady On

Off

(steady off)

Flash

(long on, long off)

Alternating Red/Green Flash

(red on, green on, red on,

green on)

Wink

(long on, short off)

Line Button

Line is busy. Green means your phone is busy; red means someone at another extension is busy on the line.

Line is idle (not being used).

A call is ringing on the line. — Green flash means a call is

ringing at your extension. Red flash means a call is ringing on the line, but not at your extension.

Alternating green and red flash appears at both extensions in a joined call, and at any extension connected in a conference call.

A call on the line is on hold. — Green wink means the call is on hold at your extension. Red wink means the call is on hold at another extension. (Anyone who has the line can

retrieve the call.)

Green means Red means the extension feature* is on

Feature* is off Extension is idle (not

—

Feature Button

Intercom Auto Dial

is busy (making or answering a call).

being used).

Green flash means someone at another extension is calling you.

—

Green Flutter

(short on, short off)

Red Broken Flutter

(short on/off, long off)

Applies to Do Not Disturb, Night Service, Outgoing Call Restriction Button, Privacy, Voice Interrupt on Busy Talk-Back, and VMS Cover, all of which require programming on a button with lights. Can also apply to Account Code Entry, Background Music, and Call Forwarding/Call Follow-Me, if any of them are programmed on a button with lights. (For more information about programming these features, see Chapter 5.)

A call is on exclusive hold at your extension (and can only be retrieved from your extension).

—

A Wake Up Service call is being scheduled from extension 10

—

A call transferred to the extension is now returning to your phone.

Fax Management only— the fax extension is not answering calls (may be out of paper).

3-4 Learning About Telephones

Ringing Patterns

System phones have these ringing patterns:

■ An outside call will ring . . . ring . . . ring.

■ An intercom call will ring BEEP. . . ring BEEP. . . ring BEEP. If you have

a system display phone, the caller’s extension number (and name if

programmed) will show on the display.

■

A transferred call, or an unanswered transferred call that is ringing back at your extension, will ring BEEP BEEP. . . ring BEEP BEEP. . . ring BEEP

BEEP.

NOTE:

If you use the system with PBX or Centrex lines, the PBX/Centrex distinctive ringing patterns are not passed to phones. Phones use the ringing patterns described here instead.

Dial Tones

You will encounter two different dial tones when calling with a system phone:

■

Outside dial tone is generated by your local phone company to indicate

that you are connected with an outside line.

■

connected with an inside line. You hear this dial tone when you are

making an inside, or intercom, call.

Intercom dial tone is generated by the system to indicate that you are

To hear the difference between the two types of dial tones on a system phone, press a line button. The dial tone you hear is an outside dial tone. To hear an intercom dial tone, press



Intercom

.

Using the Handset, Speaker, and Microphone

Every system phone (except the MLC-6 phone) has a speaker, which you can turn on by pressing

is on. MLS-34D, MLS-18D, MLS-12D, and MLS-12 phones also have a microphone.

On these phones, pressing microphone. In addition, you can turn just the microphone on and off by pressing



Mic



Spkr

.

When the green light next to



Spkr



turns on both the speaker and the

.

When the green light next to



Spkr



is on, the speaker



Mic



is on, the microphone is on.

Learning About Telephones

3-5

If you prefer to dial and conduct calls without lifting the handset, you can use the speaker and the microphone instead. Use these techniques to make calls with the speaker and the microphone (if you have one):

■

To make a call without lifting the handset, press  Spkr  to get a dial tone; then dial the number and you will hear the call ringing. When the other party answers, you can talk without lifting the handset. On MLS-6 phones (which have no microphone), you must lift the handset to talk when the other party answers. You cannot listen through the handset and the phone’s speaker at the same time.

■

To turn off the microphone when you are using the speaker, press This will mute your voice so the other party cannot hear you.

■

If you are already on a call, you can switch from the handset to the speaker and microphone (on an MLS-34D, MLS-18D, MLS-12D, or MLS-12 phone) by pressing

 Spkr  and hanging up the handset.

Conversely, if you are using the speaker and microphone and want to switch to the handset, lift the handset and the speaker and microphone will turn off.

■

Use the Hands-Free Answer on Intercom (HFAI) feature to answer

voice-signaled calls without lifting the handset (see below).

Hands-Free Answer on Intercom (HFAI)

When you receive a voice-signaled intercom call, your phone beeps once to indicate that your speaker has been turned on automatically, and you hear the caller’s voice over your phone’s speaker. If you leave your microphone on all the time, you can start talking when you hear the caller, without lifting the handset. This feature is called Hands-Free Answer on Intercom.

NOTE:

Since MLS-6 phones do not have microphones, you must lift the handset to answer voice-signaled calls to those phones.

Any user in the system can make a voice-signaled call to an idle MLS-model

system phone by pressing

or pressing an Auto Dial button programmed for voice signaling. (You can make a voice-signaled call from either a system phone or a standard phone. However, if you try to make a voice-signaled call to a standard phone or MLC-6 phone, it will ring.)



Intercom

  ✳ 

 Mic .

and then dialing an extension number

NOTES:

The HFAI feature can be turned on or off only when your phone is idle. Muting your voice while you are on a call only turns off the microphone for the duration of the call.

2. If HFAI is on and you are already on a call, you will not hear any other voice signals to your extension.

If you make a voice-signaled intercom call to a busy extension, you may

3. initiate a voice interrupt on busy call to that extension. See “Voice Interrupt On Busy Calls” on the next page for more information.

3-6

Learning About Telephones

Voice Interrupt on Busy Calls

A voice interrupt on busy call is a special intercom call that lets you interrupt

and speak to another user who is busy on a call and who has the Voice Interrupt On Busy feature (#312) activated for that user’s phone. When you use Voice Interrupt on Busy to interrupt another user on a call, the interrupted user hears two beeps before hearing your voice. Be aware that the third party to whom the interrupted user is speaking will probably hear the two beeps and the faint sound of your voice. Therefore, the message you deliver with the interruption should be brief and discreet. If the interrupted user wants to answer you, he or she can press a programmed Talk-Back button—the interrupted user’s response cannot be heard by the third party in this case.

Speakerphone Performance Tips

The speaker on your MLS-34D, MLS-18D, MLS-12D, or MLS-12 telephone has a sensitive sound-activated switch. Room acoustics and background noise can affect the proper operation of the speakerphone. To ensure that your speakerphone works effectively, follow these guidelines:

■

Avoid placing your phone in areas with high background noise caused by

loud voices, radios, printers, copiers, typewriters, other noisy office

equipment, and heater and air conditioning fans.

■

Avoid rustling papers near the microphone (lower right corner of your

phone).

Avoid talking before the other person is finished speaking. When you

■

both talk at the same time, only one person’s voice comes through.

■

Do not use your speaker to make announcements over a loudspeaker

paging system connected to your phone system.

■

When talking, always face your phone and stay within two feet of it.

■

Place your phone at least six inches away from the edge of your desk.

■

If you have difficulty hearing the other party, try increasing the speaker volume. If you have background noise, try turning off the microphone when the party at the other end is speaking and turning it on when you speak. If the difficulty persists, lift your handset to continue the conversation.

■

In conference rooms, a separate speakerphone (such as the AT&T S203 Speakerphone) is recommended, since the built-in speaker on a system phone is designed for individual use.

Standard Telephones

In addition to system phones, you can connect industry-standard touch-tone or

rotary dial phones—and even some feature phones (which have built-in calling features)—directly to the system. You can also combine standard phones on the same extension with system phones or other devices, without using expensive adapters or connectors.

Learning About Telephones

3-7

Standard phones can do many of the things that system phones can do, and you can save money by using them in certain situations when a system

telephone is not needed. Follow these guidelines when using standard phones:

■

Use standard phones as power failure backups. In the event of a power

failure, standard phones at extensions 10, 16, 22, and 28 connect to lines

1, 3, 5, and 7, respectively, for continued operation; but system phones will not work. You can connect standard phones in combination with system phones at power failure extensions, or you can simply keep spare standard phones at those extensions to serve as replacements in case of a power failure.

To use a system feature, press

■

phones) followed by its two-digit code when you hear intercom dial tone. For features that use code when you hear intercom dial tone. (Instructions for using these features on standard phones are included in Chapter 5, “Feature Reference.”)

To use a Speed Dial number, press

■

when you hear intercom dial tone. (For details, see “System Speed Dial Numbers” and “Personal Speed Dial Numbers” in Chapter 5.)

Use the switchhook on a standard phone to place calls on hold, transfer a

■

call, or set up a conference call. (For details, see “Using the Switchhook” on the next page, or “Hold,” “Transferring Calls,” and “Conference Calls” in Chapter 5.)

■

If the standard phone has a message waiting light, use it to notify users of messages. (For details, see “Message Light On” and “Message Light Off” in Chapter 5. For a list of supported phones, see “Standard Telephones” in Chapter 1.) Alternatively, if you have a voice messaging system, the light is used to indicate that a message has been left in your mailbox. On a standard phone, the message light flashes when the

phone is idle to indicate that the extension has received a message.

Ringing Patterns

 # 

(in place of



Feature



used on system

 Intercom  on system phones, dial only the two-digit

 #  followed by its two-digit code

Standard phones have these ringing patterns:

■ An outside call will ring . . . ring . . . ring.

■ An intercom call will ring-ring . . . ring-ring . . . ring-ring.

■ A transferred call, or an unanswered transferred call that is ringing back,

will ring-ring-ring . . . ring-ring-ring . . . ring-ring-ring.

NOTE:

If you use the system with PBX or Centrex lines, the PBX/Centrex distinctive ringing patterns are not passed to phones. Telephones use the ringing patterns described here instead.

3-8 Learning About Telephones

Dial Tones

Standard phones have two different dial tones:

■

Outside dial tone is generated by your local telephone company to

indicate that you are connected with an outside line.

■

Intercom dial tone is generated by the system to indicate that you are connected with an inside line. You hear this dial tone when you are making an inside, or intercom, call.

To hear the difference between the two dial tones, lift the handset. The dial tone you hear (assuming the phone is set to select intercom first, as recommended in this guide) is an intercom dial tone. To hear an outside dial tone, press

Using the Switchhook

Some of the call handling instructions in this guide direct you to “rapidly press and release the switchhook.” Pressing the switchhook for 1/4 to 1 second sends a signal over the line called a switchhook flash. However, do not press the switchhook too quickly. If you press the switchhook and nothing happens, try again and press it a little longer.

NOTE:

If your feature phone has a button labeled “Recall” or “Flash,” use the button instead of pressing the switchhook. If you use the system with PBX or Centrex lines, your PBX or Centrex documentation may tell you to press the switchhook to access PBX or Centrex features. Use the Recall feature instead (see “Recall” in Chapter 5).

 9 .

Limitations

Because standard phones do not have system line buttons, feature buttons, or dedicated function buttons, basic call handling procedures are sometimes different from those for system telephones. In addition, the following actions cannot be performed at a standard telephone:

■

You cannot enter programming mode.

■

Because there are no line buttons on standard phones, users must use Direct Line Pickup—idle Line to select a specific line; otherwise, the system selects an idle line automatically when the user dials a 9 at intercom dial tone. (For information on Automatic Line Selection, see Chapter 5.)

■

If a standard phone is in use, there is no indication of a second call and an inside caller will hear a busy tone.

■

Users can make a voice-signaled call from a standard phone, but if users try to make a voice-signaled call to a standard phone, it will ring because

the standard phone does not have a system speaker.

Users cannot use the

■

System Password.

Learning About Telephones

3-9

■

Users cannot access the following system features: Account Code Entry, Background Music, Do Not Disturb, Exclusive Hold, Privacy, Save Number Redial, VMS Cover, Voice Interrupt on Busy, Voice Interrupt on Busy Talk-Back, and Voice Mailbox Transfer.

■

Do not use Forced Account Code Entry with a standard phone, because the phone will bot be able to get dial tone and make calls.

Feature Phones

A feature phone is a standard telephone that has feature buttons in addition to the regular 12-key dial pad. For example, there are feature phones that have programmable auto dial buttons, last number redial buttons, hold buttons, and built-in speakers. Even though some feature phones have buttons like those provided on system phones, they may not work. Refer to the feature phone’s documentation for more information on what these phones can do.

Combination Extensions

A combination extension is an extension with two devices connected to it—either two standard devices, or a system phone and a standard device (but not two system phones). (For instructions on how to install a combination extension, see the PARTNER Plus Communications System Installation guide.)

The following are examples of useful combination extensions:

■ System phone plus standard telephone, for power failure backup on

extensions 10, 16, 22, and 28 System phone plus answering machine

■

System phone plus fax machine

■

System phone plus headset

■

System phone plus an external alert (such as a bell or chime).

Using the telephones in a combination extension is fairly simple. The main thing to understand is that the two telephones share a single extension in the same way several home telephones share a single line. A system telephone works like it always does and a standard telephone works like it always does when connected to the system. Only one phone or device can be used at a time, unless you want to join the two on a single call (the same way two people can pick up the same call on different telephones at home). For example:

■

Both phones share the same extension number.

■

Both phones share the same voicepath, that is, when either phone is busy, the extension is busy.

■

Calls ring at both phones.

■

A second call can ring at the system phone while the standard phone is busy, but do not use the system phone to answer the second call until the

standard phone is idle or the first call will be disconnected.

3-10

■

If you make a voice-signaled intercom call to a combination extension with a system phone, only the system phone signals.

Learning About Telephones

■

The lights on the system phone show what the standard telephone is doing as well as what the system phone is doing. For an explanation of light patterns, see “Lights” at the beginning of this chapter.

■

If Privacy is active at a combination extension, no other extension can

join a call in progress at either a system phone or a standard device.

(However, a phone can interrupt a call on a standard device at the same extension. For example, if a system phone and modem are combined at an extension, picking up the handset of the system phone could interrupt a modem transmission, even if Privacy is active.)

While on a call on a standard phone, you can use the system phone’s

■

dial-pad and fixed-feature buttons to handle calls. For example, you can

use the system phone to select a specific outside line, and conduct the

call on the standard phone. Or, if someone is on a call using the standard phone, someone else can put that call on hold by pressing

 Hold  on the system phone. To do this, it is not necessary to lift the

handset of the system phone. Held calls do not ring at a standard phone in a combination extension. To retrieve a held call from the standard

phone, use Direct Line Pickup—Active Line.

■

A standard phone’s message waiting light will not light if Background Music is playing through the system phone’s speaker.

The ringer equivalence number (REN) of a standard device or the

■

combined REN of two devices cannot be greater than 2.0. (The REN of a

system phone is 0.0.)

Using Telephones

Your system provides intuitive operation of basic call handling features, plus dial-code features that make it easy for users to handle calls flexibly and efficiently from both system and standard phones. For more information on a specific feature, refer to the feature name in Chapter 5.

Basic Call Handling Features

The following features are available from both system and standard phones:

■

Making Calls

■ Answering Calls

■

Hold (placing a call on hold)

■

Transferring Calls (passing a call to another system extension)

■ Conference Calls (making a conference call)

■

Joining Calls

Learning About Telephones

3-11

Dial-Code Features

Dial-code features are features that you access by dialing a feature code at the telephone keypad. From a system phone, you can dial followed by the two-digit code (or press a programmed Auto Dial button); from a standard phone, you typically dial have intercom dial tone. Some dial-code features are not available on standard

phones, as noted by an asterisk (*) in the following list.

Account Code Entry*

■

Background Music*

■

Call Forwarding/Call Follow-Me

■

Call Pickup

■

Conference Drop

■

Direct Line Pickup—Active Line

■

Direct Line Pickup—Idle Line

■

Exclusive Hold*

■

Group Calling—Ring/Page

■

Group Hunting—Ring/Voice Signal

■

Group Pickup

 Feature  or  Intercom ,

 #  followed by the two-digit code when you

■

Last Number Redial

■

Loudspeaker Paging

■

Message Light Off Message Light On

■

Personal Speed Dial Numbers

■

Recall

■

Save Number Redial*

■

System Speed Dial Numbers

■

Touch-Tone Enable

■

Voice Mailbox Transfer*

Available only on system phones.

3-12

Learning About Telephones

Using Auxiliary Equipment

Contents

Overview

■

If a Device Has Trouble

Answering Machines

■

Single Answering Machine

■

Multiple Answering Machines

■

Personal Answering Machine

Call Reporting Devices (SMDR)

■

Programming

■

Call Reports

■

Considerations

■

Output Format

■

Serial Printers

■

Call Accounting Devices

Credit Card Scanners Fax Machines

■

Using Fax Machines

Fax Management Feature

Transferring a Call to the Fax Machine

Using the Fax Machine’s Notify Feature

■ Setting Up Fax Machines

Restricting Dialing from a Fax Machine

■

Single Fax Machine

■

Fax Line Saver

■

Send and Receive Fax Machines

Modems

■

Stand-Alone Modem for Placing Calls Only

■

Send and Receive Modem

4-1 4-3

4-4 4-5

4-6 4-7

4-8 4-8

4-9 4-10 4-10 4-10 4-10

4-11 4-12

4-12 4-12 4-13 4-13 4-14 4-14 4-15

4-16

4-17 4-19

4-19 4-20

4-i

Contents

Night Service with Auxiliary Equipment PARTNER Attendant

■

Backup for Receptionist

Voice Messaging Systems

■

Delayed Call Handling

4-21 4-23

4-23 4-24

4-24

4-ii

Using Auxiliary Equipment

Overview

There are many ways to set up auxiliary equipment—the setup you choose depends upon your needs and the number of devices you have. This chapter

presents some common setups. (It does not cover how to physically connect

the equipment, or how to program the features. See the PARTNER Plus

Communications System Installation guide for installation instructions, Chapter 5

for programming instructions, and the equipment manufacturer’s documentation

for complete details on the device you connect.)

This chapter shows various applications for the following types of equipment:

Answering Machines

■

Call Reporting Devices

■

Credit Card Scanners

■

Fax Machines

■

Modems

■

PARTNER Attendant

■

Voice Messaging Systems

Using Auxiliary Equipment

4-1

In addition, you can connect the following devices to your system:

■

Doorphones allow visitors to signal extensions by pressing a button on the doorphone; the person who answers a doorphone call can then speak with the visitor at the doorphone. A doorphone is especially useful for providing access to offices or departments after hours. For example, you can install a doorphone outside your building entrance to allow visitors to ring telephones inside the building when the receptionist is not there and the front door is locked.

The system supports up to two AT&T PARTNER Doorphones or any number of AT&T Universal Doorphones. Universal Doorphones offer a door unlock feature and can be installed in addition to PARTNER Doorphones.

■

Loudspeaker paging systems allow you to broadcast a message over a large area, by connecting the paging system directly to the PAGE jack on the processor module. The system supports all AT&T paging systems including the entire PagePac® line, and most paging systems from other manufacturers. In addition to its numerous paging features, the PARTNER PagePac provides doorspeaker and door unlock capabilities. For information on how to use a loudspeaker paging system with the system, see Chapter 5.

■

PARTNER Passage Way™ Solution

allows you to combine your Personal Computer (PC) running Microsoft® Windows™ 3.1 with your phone. You can then use your PC for tasks such as dialing out from an electronic phone list, logging phone calls, and programming your phone.

■

Music-on-hold systems allow you to play recorded music or messages to callers while they are on hold, by connecting the audio source to the processor module. The system supports the AT&T Magic on Hold system and most models from other manufacturers. (If you use equipment that rebroadcasts music or other copyrighted materials, you may be required to obtain a license from a third party such as ASCAP or BMI.)

■

Extra alerts help make users aware of incoming calls. For example, you can use an audible alert (chime, horn, or bell) to replace a phone ring in a noisy area, such as a factory. Similarly, you can use a visual alert (strobe or light) to replace a phone ring in a quiet area, such as a library. AT&T offers several compatible alerts.

■

Speakerphones provide hands-free two-way operation of a phone without lifting the handset. Combining a speakerphone with a system phone or a standard phone in a conference room or office is an inexpensive way for several people at a meeting to conference in other parties. (System phone speakers are designed for individual use—not group use.) The system supports the AT&T S203 speakerphone and any industry-standard speakerphone.

■

Headsets allow users to hold hands-free conversations. A headset is a combination earphone and microphone worn on the head, useful for receptionists, salespeople, or others who need to have their hands free while talking on the phone. AT&T offers several compatible headsets.

4-2

Using Auxiliary Equipment

■

Specialty Handsets are designed for those individuals who need greater functionality than that provided by the handsets on system phones and standard phones. For example, an amplified handset is available for certain system phones for hard-of-hearing users.

■

In-Range Out-of-Building (IROB) protectors are required to prevent electrical surges from damaging your system when phones are installed in another building, but on the same continuous property. The system supports the AT&T IROB protector, which provides coverage for up to 3,000 feet (915 meters) for standard phones and 1,000 feet (305 meters) for system phones.

■

Electromagnetic Interference (EMI) filters allow you to block “noise” generated by a nearby radio station, as well as most electrical devices.

■

Caller ID devices, such as a PC with Caller ID software, support applications for storing or processing Caller ID information. You can connect these devices provided you subscribe to the service from your

local phone company and connect the device directly to the Caller ID line. To install devices, refer to “Connecting Caller ID Devices” in the PARTNER Plus Communications System Installation guide for details.

Follow the manufacturer’s instructions packaged with the devices. To order auxiliary equipment, refer to “Product Ordering Information” in Appendix B.

If a Device Has Trouble

Two System Programming procedures can be used to adjust the system settings for auxiliary equipment installed at an extension, if a device has trouble answering calls or dialing out. If a device (such as an answering machine) does not pick up transferred or intercom calls, you can use Distinctive Ring (#308) to change the ringing, so that all calls ring like outside calls at that extension. If an autodialing device (such as a modem) has trouble autodialing, use Intercom Dial Tone (#309) to change the intercom dial tone for the extension to Machine (outside line) dial tone.

Using Auxiliary Equipment

4-3

Answering Machines

You can use an answering machine to answer calls at night when no one is around, or during business hours when no one can get to the phone. If you have an AT&T answering machine with the Call Intercept feature, you can pick up a call that has been answered by the answering machine by joining the call from any system phone. When you do so, the system sends the answering machine a signal that makes it hang up.

The following are ways you can connect answering machines to your system:

■

Single answering machine. This basic setup can cover all the lines in the system. Anyone on the system can call the machine to retrieve messages.

■

Multiple answering machines. If you get too many calls for one machine to cover, connect two or more machines to cover all calls.

■

Personal answering machine. An answering machine can share an extension with a phone to answer calls to the extension.

NOTE:

If you have an answering machine and a system phone on the same extension, the answering machine will be able to answer calls only when the phone is idle.

4-4

Using Auxiliary Equipment

Single Answering Machine

The single answering machine setup (Figure 4-1) serves the entire system. The answering machine is connected to its own extension, and can cover all the lines in the system, or as many lines as you assign to it. You can install the answering machine on an extension by itself, or combine it with a system phone or a standard phone on the same extension (see “Combination Extensions” in

the PARTNER Plus Communications System Installation guide).

Figure 4-1. Single Answering Machine

To Use

Lines

CONTROL

UNIT

Telephone

(optional)

Ext X

ANS

MACH

■

Go to the machine to manually play back messages.

■

From any system extension, make an intercom call to the answering machine extension. When the machine answers, dial its message retrieval code.

■

From outside the system, call in on any line assigned to the machine. When the machine answers, dial its message retrieval code.

To Program

Set Line Ringing for all lines assigned to extension X to Immediate Ring.

Use Line Assignment (#301) to assign all the lines to extension X that you want the answering machine to cover.

Make sure extension X is not assigned as a Pickup Group Extension (#501),

Calling Group Extension (#502), Night Service Group Extension (#504),

or Hunt Group Extension (#505). Adjust the answering machine to answer according to your needs. For

4. example, set the machine to answer on the fourth ring during the day so someone has a chance to pick up the call.

Using Auxiliary Equipment

4-5

Multiple Answering Machines

If a single answering machine cannot handle all your calls, you can set up two or more machines at different extensions (Figure 4-2) so that a call does not go unanswered. If one answering machine is busy, a second call will be answered by the second machine. A setup such as this might be used by a movie theater to announce movie times to people calling for information.

Lines

Figure 4-2.

CONTROL

UNIT

Multiple Answering Machines

Ext X

Ext Y

ANS

MACH

ANS

MACH

To Use

■

Go to the machines to manually play back messages.

■

From any system extension, make an intercom call to an answering machine extension. When the machine answers, dial its message retrieval code.

■

From outside the system, call in on any line assigned to the machine.

When the machine answers, dial its message retrieval code. Note,

however, when calling in from outside, you can retrieve messages only

from the first machine that answers.

To Program

For extensions X and Y, set Line Ringing for all lines to Immediate Ring.

Use Line Assignment (#301) to assign all the lines to extensions X and Y that you want the machines to cover.

Make sure extensions X and Y are not assigned as Pickup Group Extensions

(#501), Calling Group Extensions (#502), Night Service Group Extensions (#504), or Hunt Group Extensions (#505).

Adjust both answering machines to answer on a different number of rings (so

4. they do not both try to pick up the same call). For example, set answering machine 1 to 4 rings and answering machine 2 to 6 rings. (If you cannot adjust the two answering machines to answer on a different number of rings, assign some lines to Immediate Ring at extension X and other lines to Immediate Ring at extension Y.)

4-6

Using Auxiliary Equipment

Personal Answering Machine

A personal answering machine is used to answer all the calls that ring at a

certain extension (Figure 4-3). It is useful for the following situations:

■

When you do not want to dedicate an extension to an answering machine

■

When the extension receives a lot of intercom calls

■

When outside calls come through a receptionist and are transferred to the

extension

■

When an extension has a private line

Lines

Ext X

ANS

MACH

CONTROL

UNIT

Figure 4-3.

Personal Answering Machine

To Use

■

Go to the machine to manually retrieve messages.

■ From any system extension, make an intercom call to the extension.

When the machine answers, dial the message retrieval code.

■ From outside the system, call in and have someone transfer you to the

extension. When the machine answers, dial the message retrieval code. Or, call in when no one will answer before the answering machine does.

To Program

Set Line Ringing for all lines assigned to extension X to the desired ring (Immediate, Delayed, or No Ring).

If the lines assigned to extension X are also assigned to other extensions, adjust the answering machine to answer on the third or fourth ring so that it does not answer calls before someone else can.

NOTE:

If you intercept a call from the answering machine, you will hear a click to notify you that the answering machine has turned off.

Using Auxiliary Equipment

4-7

Call Reporting Devices (SMDR)

SMDR (Station Message Detail Recording) is a call reporting feature that provides records of call activity. Call reporting information provides you with the

ability to:

■

Detect any unauthorized calls

■

Bill clients or projects

■

Bill back by departments

■

Reduce telephone costs by identifying the need to change

telecommunications services (like adding a WATS line for calls to a

particular area code)

Call reporting information is recorded after each call is completed. The system

records information for each call that lasts at least 10 seconds. For outgoing

calls, the timing begins when you get dial tone. For incoming calls, the timing

begins when you answer the call. Timing stops when the call is disconnected.

The system sends the information through a 1200-baud serial interface to either

a serial printer or a call accounting device. The device connects directly to the

SMDR jack on the processor module.

Programming

Use the following programming procedures for call reporting:

■

SMDR Record Type (#608) to specify the type of calls that you want to record for call reporting—either all calls or outgoing calls only.

■

SMDR Top of Page (#609) to notify the system that the printer has been aligned to the top of a new page.

■

Forced Account Code Entry (#307) to identify extensions that are required to enter an account code prior to making outside calls and Forced Account Code List (#409) to create a list of valid account codes.

■

Display Language (#303) to specify the language to be used for display messages. The call report header is printed in the same language as is specified for extension 10.

4-8

Using Auxiliary Equipment

Call Reports

A call report is a page of information that begins with a header. The header includes field names that describe the information in each call record. The call record is a line of information that includes the fields shown in Figure 4-4.

DATE

C 11/17/93 11:11 C 11/17/93 11:34 I 11/17/93 13:35

Figure 4-4.

Sample Call Report

Each page includes 59 records. The report has the following fields:

■

Call Type. “C” indicates outgoing calls; “I” indicates incoming calls.

(SMDR Record Type (#608) defines whether or not incoming calls are reported.)

■

Date. The date of the call is shown in mm/dd/yy format, where mm is the month, dd is the day, and yy is the year. The system uses the date set with System Date (#101).

■

Time. The time of the connection is shown in hh:mm format, where hh is the hour and mm is the minute. The system uses the time set with System Time (#103) and is shown in 24-hour (military) time.

■

Number. For an outgoing call, this is the dialed number (first 15 digits only) or the speed dial code of a Marked System Speed Dial number (preceded by an “F”). For an incoming call, “IN” appears in this field.

A “*” character prints as the last digit of a dialed number if the called party hangs up before the system user, or a “?” prints if the number of digits dialed exceeds the 15 digits that this field can hold.

TIME

CALLED NUMBER

12015558014 19085556036

DUR.

00:01:40 00:04:28 00:02:12

LINE

STN.

ACCOUNT

18 32 1725 10

■

Duration. The duration of the call is shown in hh:mm:ss format, where hh is the hour, mm is the minutes, and ss is the seconds. This is the total time of the call, including any time the call is on hold.

■

Line Number. This is the outside line (01–12) that was used to make or receive the call.

■

Station (Extension). In general, this is the extension that answered or placed the call. For redirected incoming calls, the last extension on the call is shown on the report, as follows:

– For transferred incoming calls: the destination extension. –

For transferred outgoing calls: the originator extension.

–

For pickup calls: the extension picking up the call.

–

For forwarded calls: the extension answering the forwarded call.

■

Account Code. This is the account code (up to 16 digits) assigned to the call. This code is typically used for charging calls to a specific project or department.

Using Auxiliary Equipment

4-9

Considerations

■

Output Format

The following serial transmission protocol is used for SMDR records:

■

The System Date (#101) and System Time (#103) must be set correctly to ensure accurate call reports.

If a report cannot print because the printer is jammed or out of paper, the

system will store up to 45 records in its memory until they can be printed.

Additional calls will not be recorded. In the event of a power failure, records of any calls in progress are lost. Inside (intercom) calls are not recorded. If you place a call on hold and the caller hangs up, the call is considered

complete and the record is sent to the call reporting device. Conference calls appear as two outside calls. (This means two records

are generated on the report.)

1200 baud

no parity

8 data bits 2 stop bits

The call reporting feature also supports XON/XOFF protocol, carriage returns,

and line feeds.

Serial Printers

Use a 355A adapter, which converts a modular jack interface to an RS-232 25-pin connector, to connect a serial printer to the processor module. If you connect a printer, make sure the printer can receive SMDR data in the format described above (refer to the printer’s instructions if you need help).

Call Accounting Devices

You can send call information to a call accounting device (such as AT&T’s Call Accounting Terminal—Basic or Plus) if you want to further analyze call activity. The device stores rate table information and processes the information it

receives into meaningful reports that can help you optimize your communications system. For example, you can use it to determine the best combination of local and long distance lines for your business.

The call accounting device connects directly to the SMDR jack on the processor

module and can also print out reports that include summaries by hour, line, and extension. Refer to the manual provided with the call accounting device for instructions on connecting it to your system.

4-10

Using Auxiliary Equipment

Credit Card Scanners

Many retail businesses and restaurants use credit card scanners to get instant approval of credit card purchases. The system allows your credit card scanners to share the lines in your system (as shown in Figure 4-5). You can install the credit card scanner on an extension by itself, or combine it with a system phone or a standard phone on the same extension (see “Combination Extensions” in the PARTNER Plus Communications System Installation guide).

Lines

Figure 4-5.

CONTROL

UNIT

Credit Card Scanner

Telephone

(optional)

Ext

Credit

Card

Scanner

To Use

When you make a call on the credit card scanner, an outside line is

automatically selected. If you combine the credit card scanner with a system phone or standard phone, you cannot use the phone while the credit card

scanner is operating. You can use only one of the devices at a time.

To Program

Set Automatic Line Selection for extension X to select outside lines first.

Use Line Assignment (#301) to assign the lines you want the scanner to use to extension X.

3. Set Automatic Extension Privacy (#304) for extension X to Assigned.

If the scanner has an auto answer feature, turn it off. For multiple scanners, repeat Steps 1–4 for each extension.

Using Auxiliary Equipment

4-11

Fax Machines

This section suggests several ways you can set up fax machines to work with your system. It includes instructions for programming and using a Fax

Management button on a system phone (in order to monitor the status of a fax machine and transfer calls to it with a single touch), transferring calls to the fax machine extension, and using an AT&T fax machine’s Notify feature.

Using Fax Machines Fax Management Feature

On any system phone, you can program a button with lights to serve as a Fax

Management button. The lights next to this button tell you when the fax machine

is in use, available, or not answering (for example, when it is out of paper). You can also use the button to transfer calls from your extension to the fax machine with a single touch.

Programming for Fax Management

To program a Fax Management button, first assign the fax machine extension

using Fax Machine Extensions (#601). (See Chapter 5 for details.) Then

program the fax machine extension number on an Auto Dial button. For more

information, see “Auto Dialing” in Chapter 5.

Using the Fax Management Button

The lights next to the Fax Management button show what is happening at the fax

machine—see Table 4-1.

Table 4-1. Fax Management Button Light Patterns

Light Pattern

Red broken flutter

Red steady

Green flash

Green flutter

Indicates...

Fax trouble. The fax machine is not answering. If broken flutter occurs because the fax machine is out of paper, refill the paper. The light clears the next time the machine transmits or receives a call. If the machine takes longer than four rings to answer, the light shows fax trouble; when the machine does answer, the light changes to fax busy (red steady).

Fax busy. The fax machine is busy transmitting or receiving a call.

Fax calling. The green flash indicates that the fax machine extension is calling you. An AT&T fax machine with the “Notify” feature can call you automatically after it receives a transmission. See “Using the Fax Machine’s Notify Feature” on the next page.

Fax transfer return. A call you transferred to the fax machine was not answered and is returning to you.

4-12

Using Auxiliary Equipment

Transferring a Call to the Fax Machine

There are two situations in which you would want to transfer a call to your fax machine:

■ You answer an outside call and hear a fax machine signaling. (A fax

signal is a single beep sequence— beep . . . . beep . . . . beep). If you

hear this, you should transfer the call immediately to the fax machine extension.

■

You are on a call with a person who wants to send you a fax using the fax machine that is connected to his or her phone. You can receive the fax by transferring the call to your fax extension. Tell the other party to wait until he or she hears the fax signal before pressing the Start button on their fax machine.

In addition, if you have a PARTNER MAIL system and a fax call comes in on a line covered by the PARTNER MAIL system, its Automated Attendant Service can be programmed to automatically transfer the call to a fax extension or (if you have multiple fax machines) to the extension Hunt Group for the fax machines.

There are four ways to transfer the call to the fax extension:

■

If you have a Fax Management button, simply press the button. When the fax machine answers, hang up.

■

If you do not have a Fax Management button, press machine’s extension number. When the fax machine answers, hang up.

On a standard phone, rapidly press and release the switchhook to place

■

the call on hold, then dial the fax extension number and hang up.

■

If you have multiple fax machines in an extension Hunt Group, press



Transfer

,

then



Intercom

  7   7 

When a fax machine answers, hang up.

Using the Fax Machine’s Notify Feature

Some AT&T fax machines (for example, models 5300, 5350, 9025 Plus, and 9035 Plus) have a feature called Notify. After such a machine receives a fax call, it automatically dials a number and plays a recorded message, such as, “You have just received a fax.” If you need to know exactly when a fax comes in, or if your fax machine is located in an isolated part of your building, you can use Notify in any of the following ways:

■

Program the fax machine to make a ringing or voice-signaled intercom call to an individual extension or to a group. (Program the fax machine to dial

 ✴ 

plus the extension number for a voice-signaled call;

group number (1–4) for a call to a Calling Group;

number (1–6) for a call to a Hunt Group.)

■

Program the fax machine to turn on the message light at someone’s extension by dialing

■

Program the fax machine to dial announcement over your loudspeaker paging system.

 #   0   9 

 Transfer  plus the fax

plus the fax extension Hunt Group number.

 7 

and a

 7   7 

and a group

plus the extension number.

 7   0 

to make its recorded

Using Auxiliary Equipment

4-13

For all of these examples, program the fax machine extension’s Automatic Line Selection to select intercom first, followed by whatever outside lines you want to

assign to it. (If you set the fax extension to select intercom first and the machine has an auto dial feature, program a 9 and a few pauses before each Auto Dial number. When manually making a call, dial instructions on how to set the Automatic Line Selection, see Chapter 5.)

Setting Up Fax Machines

There are many ways to set up fax machines. The following configurations are basic and easy to use:

■

Single fax machine. Good for light or moderate fax traffic. This basic

setup uses a published fax number.

■

Fax machine line saver. Good for light fax traffic, with no need for a published fax number.

■

Send and receive fax machines. Good for high-volume fax traffic. One

machine sends, the other receives.

You can install both a telephone and a fax machine on the same extension—see “Combination Extensions” in the PARTNER Plus Communications System Installation guide. This lets you receive both voice and fax calls on the same line (but not at the same time). If you pick up the phone and hear a fax signal, push the Start button on your fax machine and then hang up.

 9  to get an outside line. For

If you are using the PARTNER MAIL system’s Automated Attendant Service, you can program PARTNER MAIL to transfer fax calls to the fax extension or a group of fax extensions automatically. Use Fax Machine Extensions (#601) to identify fax extensions. If you have multiple fax machines, put all of the fax extensions into a single Hunt Group (any of groups 1–6) using Hunt Group Extensions

(#505).

Restricting Dialing from a Fax Machine

You can use dialing restrictions to restrict calling activity on a fax machine. For example, you can use Outgoing Call Restriction (#401) to restrict the fax machine to local calls only. For a more detailed discussion of dialing restrictions, see Chapter 2.

4-14

Using Auxiliary Equipment

Single Fax Machine

The single fax machine setup (shown in Figure 4-6) is good for moderate traffic. The fax machine has its own line (Line A), the number of which is published as the fax number. (The fax line can be used by other phones when all other lines are busy.) The fax machine is connected to its own extension (extension X).

Fax Line A

Figure 4-6.

CONTROL

UNIT

Ext

Single Fax Machine

FAX

To Use

The fax machine automatically answers all calls that come in on the fax line. If a call comes in on another line, you can transfer the call to the fax extension (see “Transferring a Call to the Fax Machine”). If you have programmed a Fax Management button, you can transfer a call to the fax machine with a single touch, as well as monitor the status of the fax machine (see “Fax Management Feature” earlier in this chapter).

When you send a fax, the system automatically selects the fax line.

To Program

Set Automatic Line Selection for extension X to select line A only. Set Automatic Line Selection to select line A last on all other extensions or remove line A if all other extensions should not use it to make outgoing calls.

Set Line Ringing for line A on extension X to Immediate Ring. On all other extensions, set line A to Delayed Ring or No Ring.

Use Line Assignment (#301) to assign only line A to extension X.

Set Automatic Extension Privacy (#304) for extension X to Assigned. Make sure extension X is not assigned as a Pickup Group Extension (#501),

Calling Group Extension (#502), Night Service Group Extension (#504),

To monitor the fax machine, use Fax Machine Extensions (#601) to identify

6. extension X as a fax extension and program a Fax Management button by programming the fax machine extension number on an Auto Dial button.

Hunt Group Extension (#505).

Using Auxiliary Equipment

4-15

Fax Line Saver

If you do not use your fax machine enough to justify paying for its own outside line, you can put the machine on its own extension. With this setup, you must transfer calls to it manually. If you have programmed a Fax Management button, you can transfer a call to the fax machine with a single touch, as well as monitor the status of the fax machine (see “Fax Management Feature” earlier in

this chapter). Figure 4-7 shows the setup.

Lines

Figure 4-7.

CONTROL

A B C

UNIT

Fax Line Saver Setup

Ext X

FAX

To Use

When a person answers a call and hears a fax machine signaling on the other end, the person can transfer the call to extension X—the fax machine extension. To send a fax transmission, simply lift the handset on the fax machine—an outside line will be automatically selected.

To Program

Set Automatic Line Selection for extension X to Line A, B, C, . . . .

Set Line Ringing for all lines on extension X to No Ring.

Use Line Assignment (#301) to assign all lines to extension X.

Set Automatic Extension Privacy (#304) for extension X to Assigned. Make sure extension X is not assigned as a Pickup Group Extension (#501),

Calling Group Extension (#502), Night Service Group Extension (#504), or Hunt Group Extension (#505).

To monitor the fax machine, use Fax Machine Extensions (#601) to identify

6. extension X as a fax extension and program a Fax Management button by programming the fax machine extension number on an Auto Dial button.

4-16 Using Auxiliary Equipment

Send and Receive Fax Machines

If your business has high-volume fax traffic, you can set up two fax machines, one that only sends and the other that only receives. For example, in Figure 4-8, fax 1 is the send machine, fax 2 is the receive machine. Line A is the fax line, the number of which is published as the fax number. If fax 2 doesn’t answer line A, fax 1 will.

Fax Line A

Lines

Figure 4-8.

Ext X

CONTROL

UNIT

Ext Y

Send and Receive Fax Machines

FAX 1

Send

FAX 2

Receive

To Use

When you send a fax, an outside line will be automatically selected. Incoming fax calls on the fax line are answered automatically by fax 2. If a fax comes in on a line other than line A, you can transfer the call to fax 2 (see “Transferring a Call to the Fax Machine” earlier in this chapter). If you have programmed a Fax Management button, you can transfer a call to the fax machine with a single touch, as well as monitor the status of the fax machine (see “Fax Management Feature” earlier in this chapter). If fax 1 is set for Delayed Ring on line A, fax 1 can pick up fax transmissions when fax 2 does not answer.

To Program Fax 1 (Send—Ext. X)

Set Automatic Line Selection for extension X to select outside lines first (line A selected last).

Set Line Ringing for line A at extension X to Delayed Ring; set all other lines to No Ring.

Use Line Assignment (#301) to assign one or more lines to extension X (including line A).

Set Automatic Extension Privacy (#304) for extension X to Assigned. Make sure extension X is not assigned as a Pickup Group Extension (#501),

Calling Group Extension (#502), Night Service Group Extension (#504), or Hunt Group Extension (#505).

To monitor the fax machine at extension X, use Fax Machine Extensions

6. (#601) to identify extension X as a fax extension and program a Fax Management button by programming the fax machine extension number on an Auto Dial button.

Using Auxiliary Equipment

4-17

To Program Fax 2 (Receive—Ext. Y)

If the fax machine has the Notify feature, set it to select intercom first. If the fax machine does not have the Notify feature and you want it to be able to dial out when fax 1 is unavailable, set Automatic Line Selection for extension Y to select outside lines first (line A selected last).

Set Line Ringing for line A at extension X to Immediate Ring; set all other lines at extension Y to No Ring. (For all other extensions, set line A to No Ring or Delayed Ring.)

Use Line Assignment (#301) to assign only line A to extension Y.

Set Automatic Extension Privacy (#304) for extension Y to Assigned. Make sure extension Y is not assigned as a Pickup Group Extension (#501),

Calling Group Extension (#502), Night Service Group Extension (#504),

Hunt Group Extension (#505).

To monitor the fax machine at extension Y, use Fax Machine Extensions

6. (#601) to identify extension Y as a fax extension and program a Fax Management button by programming the fax machine extension number on an Auto Dial button.

4-18

Using Auxiliary Equipment

Modems

There are several ways to use modems with your system, as described below.

NOTE:

Modems can connect directly to an extension jack without an adapter.

However, if you connect a high-speed modem through the control unit, you may experience some degradation of efficiency and throughput, depending on the quality of the central office lines connected to the system. To solve the problem,

either connect modems directly to the network interface jacks, or contact your

local telephone company for information about upgrading line quality.

Stand-Alone Modem for Placing Calls Only

A modem and a terminal allow you to dial out and connect to computer bulletin boards and other data services. This setup, which lets you dial out but not

receive calls, is shown in Figure 4-9. Note that the telephone is optional and can be used if you want the terminal to share an extension with a phone.

Lines

Figure 4-9.

CONTROL

UNIT

Ext

Stand-Alone Modem for Placing Calls Only

Telephone

(optional)

Modem

PC or

Terminal

To Use

Follow the modem manufacturer’s instructions.

To Program

If the modem will only dial outside the system, set Automatic Line Selection

1. for extension X to select outside lines first. If you also use the modem for calls within the system, set Automatic Line Selection to select intercom first, and include a 9 in the modem’s dialing sequence for outside calls.

Set Line Ringing for all lines assigned to extension X to No Ring.

Use Line Assignment (#301) to assign one or more lines to extension X.

Set Automatic Extension Privacy (#304) for extension X to Assigned. Make sure extension Y is not assigned as a Pickup Group Extension (#501),

Calling Group Extension (#502), Night Service Group Extension (#504),

or Hunt Group Extension (#505).

Set the auto answer feature of the modem to Off.

Using Auxiliary Equipment

4-19

Send and Receive Modem

If you need to place and receive calls with the modem, use the setup shown in Figure 4-10. This setup makes line A the primary modem line, but keeps the line available for users at other extensions when all other lines are busy.

Modem Line A

Lines

Figure 4-10.

CONTROL

UNIT

Send and Receive Modem

Ext

MODEM

To Use

Calls on the modem line (line A) ring only at extension X. Likewise, line A is the last line selected by other extensions in the system, so the modem line is unavailable for the modem only when all other lines in the system are being

used.

To Program

Set Automatic Line Selection for all other extensions so that line A is the last

line in the select sequence. That way, the modem line is used for outgoing

voice calls only when all other lines are busy.

Set Line Ringing for all lines assigned to extension X to No Ring.

Use Line Assignment (#301) to assign one or more lines to extension X.

Set Automatic Extension Privacy (#304) for extension X to Assigned.

4-20

Using Auxiliary Equipment

Night Service with Auxiliary Equipment

You can set up modems, fax machines, and answering machines to receive calls automatically after hours. When Night Service is on, calls ring immediately at the appropriate extensions, so that no human intervention is required to transfer calls to the fax, modem, or answering machine. When Night Service is off, you can use the auxiliary equipment lines for normal business purposes, so that lines are dedicated to auxiliary equipment only after hours.

By putting auxiliary equipment in the Night Service Group as described in this section, auxiliary equipment can start ringing and answering calls whenever you turn Night Service on. In other words, the Night Service button at extension 10 acts like a switch, turning auxiliary equipment on and off, as well as putting the system into Night Service.

NOTE:

If you have a voice messaging system, turning Night Service on also activates Night Service operation of the voice messaging system.

Figure 4-11 shows a system with a fax machine and a modem connected to separate extensions. Line A is published as the fax line, and line B is published as the modem line.

Lines

Figure 4-11.

CONTROL

UNIT

Night Service with Fax Machine and Modem

Ext

FAX

MODEM

To Use

During the day, lines A and B do not ring at extensions X and Y. When you turn Night Service on, calls on line A ring immediately at the fax (extension X). Since that line is not assigned to any other extension in the Night Service Group, only extension X receives fax transmissions. Likewise, with Night Service on, calls on line B ring immediately at the modem (extension Y). All lines ring at the system phone at extension Z.

Using Auxiliary Equipment

4-21

NOTE:

If answering machines are connected to Night Service extensions, you can join a call that was already answered by an answering machine from any system phone. If you have an AT&T answering machine with the Call Intercept feature, the answering machine drops off the call when you join it.

To Program

Set Line Ringing for line A at extension X and for line B at extension Y to No Ring.

Use Line Assignment (#301) to assign line A to extension X (for the fax

2. machine to cover), line B to extension Y (for the modem to cover), and all lines to extension Z.

Make sure extensions X and Y are not assigned as Pickup Group Extensions

(#501), Calling Group Extensions (#502), or Hunt Group Extensions (#505).

Assign a Night Service Button (#503) at extension 10.

4. Assign extensions X and Y to the Night Service Group (#504).

4-22

Using Auxiliary Equipment

PARTNER Attendant

The PARTNER Attendant answers calls and directs them to a specified extension or to a Hunt Group (based on the digits a caller dials after listening to a list of choices in a recorded greeting). For example, the PARTNER Attendant could answer calls and tell callers to press 1 for Sales, 2 for Parts, 3 for Service, and so on. The PARTNER Attendant can be set up for immediate call handling or delayed call handling.

Backup for Receptionist

A common use of PARTNER Attendant is as a backup for the receptionist. If the receptionist cannot pick up a call within a specified number of rings, PARTNER Attendant handles it. This prevents calls from going unanswered. Figure 4-12 shows how the PARTNER Attendant would be connected to your system.

PARTNER Attendant

Lines

CONTROL

UNIT

Ext.

Receptionist's

Desk

Figure 4-12. Backup for Receptionist

To Use

Follow the instructions packaged with the PARTNER Attendant. Make sure that the unit is in backup call answering mode.

When callers call the main number for your company, the receptionist normally picks up the call. If the receptionist is busy, the PARTNER Attendant answers

and plays a recorded message, such as: “Please hold for the receptionist or

dial an extension number now.”

To Program

Set Line Ringing for all lines assigned to the PARTNER Attendant to Delayed

1. Ring.

Set the PARTNER Attendant to pick up within a specific number of rings, so if the receptionist does not pick up a call, the PARTNER Attendant will.

Using Auxiliary Equipment

4-23

Voice Messaging Systems

Two voice messaging systems are compatible with your system. You can install one or the other, depending on your business needs:

The PARTNER MAIL VS Voice Messaging System, which physically

■

resembles a 206 module, resides in the control unit and provides voice messaging capabilities for up to 10 subscribers. An optional Mailbox Expansion Card can extend service for up to 20 subscribers.

■ The PARTNER MAIL Voice Messaging System is an auxiliary device

that connects to the system through extension jacks. It is available in a 2-port or 4-port configuration, providing service for up to 20 or 40 subscribers, respectively.

Both voice messaging systems offer your business complete call processing features. Specifically, they can:

■

Insure that incoming calls are answered and directed to destination extensions correctly and efficiently, using immediate or delayed call handling. (Immediate call handling sends calls directly to the voice

messaging system, while delayed call handling allows the receptionist to answer calls first.)

■

Answer and route calls during the day and after normal business hours.

■

Alleviate the problem of inaccurate or incomplete messages by allowing callers to leave detailed, confidential messages for subscribers.

■

Allows subscribers to assign a password to their mailbox, change their

personal greeting, and retrieve messages.

The PARTNER MAIL system also offers advanced voice mail features, such as outcalling, group lists, broadcast messages, and fax management. You can refer to the documentation provided with your voice messaging system for complete details.

Delayed Call Handling

Figure 4-13 shows a PARTNER MAIL VS system that provides delayed call handling. This setup allows the receptionist at extension 10 to provide personalized service by answering calls during the day. The PARTNER MAIL VS system (connected to extensions Z1 and Z2) is used to handle calls when the receptionist is busy or not available, so calls do not go unanswered. The PARTNER MAIL VS system also answers calls received after business hours and prompts callers to leave a message in the receptionist’s mailbox.

This example also includes two user extensions (X and Y), which are not automatically covered by the PARTNER MAIL VS system. This allows the receptionist to give the caller more personalized service; if the receptionist transfers a call to extension X or Y and that extension does not answer, the call returns to the receptionist. The receptionist can then take a message or send the call to the extension’s mailbox if the caller prefers.

4-24

Using Auxiliary Equipment

PARTNER MAIL VS

Lines

System

Ext. Z1

Ext. Z2

CONTROL

UNIT

(not automatically

Ext. X

covered by the PARTNER MAIL VS

Ext. Y

System)

Ext. 10

Receptionist’s Desk

Figure 4-13. Delayed Call Handling

To Use

Follow the instructions packaged with the PARTNER MAIL VS system to install it. During the day, the PARTNER MAIL VS system uses delayed call handling; the

receptionist picks up all calls at extension 10. If the receptionist cannot answer within four rings, the system routes the call to the PARTNER MAIL VS system where the day menu plays to the caller. At night (when Night Service is activated at extension 10), outside calls are answered directly by the PARTNER MAIL VS system. Any user who is still in the office can pick up calls before the PARTNER MAIL VS system answers.

To Program

The following list summarizes the PARTNER Plus system programming procedures you use to implement the previous example:

Use Group Call Distribution (#206) to assign outside lines to Hunt Group 7 (the VMS hunt group) to provide Automated Attendant Service on these lines.

Use Transfer Return Extension (#306) for extensions Z1 and Z2 to ensure that calls transferred by the PARTNER MAIL VS system return to extension 10 if they are not answered.

Use Hunt Group Extensions (#505) to assign extensions Z1 and Z2 to Hunt Group 7 (the VMS hunt group).

Set the VMS Hunt Delay (#506) to Delayed.

Set the VMS Hunt Schedule (#507) to Always. Make sure that a Night Service Button (#503) is assigned at extension

6. 10—the receptionist’s extension. When Night Service is on, callers hear the night menu when no one is available to answer their calls.

Program a Voice Mailbox Transfer button at extension 10 to enable the receptionist to transfer calls directly to extension X’s and Y’s mailboxes without first ringing their phones. (This is useful when the receptionist knows that the users at extensions X and Y are away from their desk.)

Program an Auto Dial button for the VMS hunt group

(

Intercom

  7   7   7 )

extensions X and Y to allow the subscribers to call in for their messages with one touch.

Using Auxiliary Equipment

4-25

Feature Reference

Contents

Overview AA Extensions (#607) Abbreviated Ringing (#305) Account Code Entry (F12) Allowed List Assignments (#408) Allowed Phone Number Lists (#407) Answering Calls Auto Dialing Automatic Extension Privacy (#304) Automatic Line Selection Automatic VMS Cover (#310) Background Music (F19)

Call Forwarding/Call Follow-Me (F11) Call Pickup (I6XX) Calling Group Extensions (#502) Conference Calls Conference Drop (F06)

5-1 5-2 5-3

5-4 5-7 5-8 5-10 5-12 5-14 5-15 5-17 5-18 5-20 5-22 5-23 5-24 5-26

Copy Settings (#399) Dial Mode (#201) Direct Line Pickup—Active Line (I68LL) Direct Line Pickup—Idle Line (I8LL) Disallowed List Assignments (#405) Disallowed Phone Number Lists (#404) Display Display Language (#303)

5-27 5-28 5-29 5-31 5-32 5-33 5-35 5-37

5-i

Contents

Distinctive Ring (#308)

Do Not Disturb (F01)

Doorphone Alert Extensions (#606) Doorphone Extension (#604 and #605) Emergency Phone Number List (#406)

Emergency Telephone (#311)

Exclusive Hold (F02)

Extension Name Display Fax Machine Extensions (#601) Forced Account Code Entry (#307) Forced Account Code List (#409)

Group Call Distribution (#206)

Group Calling—Ring/Page (I7G/I*7G)

Group Hunting—Ring/Voice Signal (I77G/I*77G)

Group Pickup (I66G)

Hold Hold Disconnect Time (#203) Hotline (#603) Hunt Group Extensions (#505)

Intercom Dial Tone (#309) Joining Calls Last Number Redial (F05) Line Access Restriction (#302)

5-38 5-39 5-40 5-41 5-42 5-44 5-46 5-47 5-49 5-50 5-52 5-54 5-56 5-58 5-61 5-63 5-65 5-66 5-68 5-70 5-71 5-73 5-74

5-ii

Line Assignment (#301) Line Ringing Loudspeaker Paging (I70)

Making Calls

Message Light Off (F10)

Message Light On (F09) Music On Hold (#602) Night Service Button (#503) Night Service Group Extensions (#504) Number of Lines (#104) Outgoing Call Restriction (#401)

5-76 5-78 5-80 5-82 5-86 5-88 5-90 5-92 5-94 5-95 5-96

Contents

Outgoing Call Restriction Button (#114) Outside Conference Denial (#109) Personal Speed Dial Numbers Pickup Group Extensions (#501) Privacy (F07) Recall (F03) Recall Timer Duration (#107) Rotary Dialing Timeout (#108) Save Number Redial (F04) SMDR Record Type (#608) SMDR Top Of Page (#609) Special Dialing Functions System Date (#101) System Day (#102) System Password (#403) System Reset—Programming Saved (#728) System Speed Dial Numbers

5-98 5-100 5-101 5-103 5-104 5-105 5-107 5-108 5-109

5-110 5-111 5-112 5-114 5-115 5-116 5-117 5-118

System Time (#103) Toll Call Prefix (#402) Touch-Tone Enable (F08) Transferring Calls Transfer Return Extension (#306) Transfer Return Rings (#105) VMS Cover (F15) VMS Hunt Delay (#506) VMS Hunt Schedule (#507) Voice Interrupt On Busy (#312) Voice Interrupt On Busy Talk-Back (F18) Voice Mailbox Transfer (F14) Wake Up Service Button (#115)

5-121 5-122 5-123 5-124 5-127 5-128 5-129 5-131 5-132 5-133 5-135 5-136 5-137

5-iii

Feature Reference

Overview

This chapter provides reference information for programming and using system features. Features are listed in alphabetical order. System Programming procedures include the procedure code (# and three-digit number) in the heading; dial-code features include the feature code (F for

 Intercom , plus a two-digit code). Some feature codes also include a variable:

XX for a two-digit extension number from 10–33, LL for a two-digit line number from 01–12, or G for a single-digit group number. Headings with no codes are general call-handling topics and Telephone Programming procedures.

 Feature  or I for

Each feature includes the following information, if applicable:

■

Description

■

Related Features

■

Considerations

■

Valid Entries (

This chapter gives step-by-step instructions, using the following conventions:

■

Programming instructions tell you to use the  Next Data  button to change values for specific settings. You can, however, enter a value using the keypad if you prefer. Similarly, there are different ways to exit programming mode as described in Chapter 2—use the method with which you are most comfortable.

■

For Telephone Programming, this chapter provides only the instructions for Centralized Telephone Programming. To program from individual extensions, users should refer to their Quick Reference cards.

All of the instructions in this chapter assume that system phones select outside lines first and standard phones select intercom first (as determined by each extension’s setting for Automatic Line Selection).

See Chapter 2 for a review of the methods and buttons you can use while in programming mode.

✔

= factory setting)

Examples

■

Programming

■

Using

Overview

5-1

AA Extensions (#607)

Description

This System Programming procedure identifies extensions where PARTNER Attendants are connected to the system. Doing so lets the system notify users with display phones when they are receiving a call that has been transferred from the PARTNER Attendant. (This procedure applies only to PARTNER Attendants—do not use it with the Automated Attendant Service of a voice

messaging system.)

Related Features

■

For each PARTNER Attendant extension, use Transfer Return Extension

(#306) to identify the extension to which a call should be routed if the

destination extension does not answer.

■

Set Automatic Extension Privacy (#304) to Not Assigned for the PARTNER

Attendant extension if you want to be able to intercept calls routed to the

device.

Considerations

■

Chapter 4 provides information on using PARTNER Attendants with the system.

■

On system display phones, “AA” displays when a call is being transferred from a PARTNER Attendant. “Transfer from AA” displays when a call transferred by a PARTNER Attendant was not answered and is being returned to your extension.

Valid Entries

1 = 2 = Not Assigned ✔

Programming

To identify an extension where a PARTNER Attendant is installed:

Assigned

Press



Feature

  0   0  

System Program

 

System Program

  #   6   0   7 .

Enter the extension number to which the PARTNER Attendant is connected.

For example, to select extension 27, press

 2   7 .

To assign or unassign the extension, press  Next Data  until the appropriate value displays.

To assign or unassign a second PARTNER Attendant extension, press

 Next Item  or  Prev Item  until the extension number shows on the display.

Then repeat Step 3. Select another procedure or exit programming mode.

AA Extensions (#607)

5-2

Abbreviated Ringing (#305)

Description

This System Programming procedure turns Abbreviated Ringing on or off at a

specific extension. When a user is on a call and Abbreviated Ringing is on, any incoming call rings only once. The green light next to the line button flashes until the call is answered or the caller hangs up (or for a transferred call, until it returns to the transfer return extension). This feature prevents incoming calls

from distracting users when they are busy on another call. To allow calls to ring

repeatedly, set Abbreviated Ringing to Not Active.

Considerations

■

Receptionists, and others who handle many calls quickly, often leave Abbreviated Ringing off, so they have an audible reminder of incoming calls.

■

Abbreviated Ringing works for both outside calls and intercom calls.

■

The volume of an abbreviated ring is lower than a normal ring.

■

Calls to a busy extension ring at a lower volume than normal even if Abbreviated Ring is set to Not Active.

■

This feature applies only to system phones.

Valid Entries

1 = 2 =

Programming

To change the Abbreviated Ringing setting for an extension:

5. Select another procedure or exit programming mode.

Active (incoming calls ring once) ✔ Not Active (incoming calls ring repeatedly)

Press



Feature

  0   0  

System Program

 

System Program

  #   3   0   5 .

display reads:

Abbrev. Ring Extension:

Enter the number of the extension to be programmed. For example, to program extension 12, press

To set Abbreviated Ringing, press

 1   2 .

 Next Data ) until the appropriate value

displays. To set Abbreviated Ringing for another extension, press

 Next Item  or  Prev Item 

until the extension number shows on the display. Then repeat Step 3.

The

Abbreviated Ringing (#305)

5-3

Account Code Entry (F12)

Description

This feature lets a user with a system phone enter an account code (up to 16 digits) for an outside call (incoming or outgoing). An account code is typically used to identify a department, project, or client for charge-back or tracking purposes.

Related Features

■

You can use Forced Account Code Entry (#307) to identify extensions that are required enter an account code prior to dialing any outside number (including those on the Emergency Phone Number List). A forced account code must be entered at the beginning of a call; however, a different account code can be entered any time during the call. (Use Forced Account Code Entry only for extensions with system phones.)

■

You can use Forced Account Code List (#409) to create a list of valid account codes, which should be distributed to the appropriate users. If a Forced Account Code List exists, the system checks the list whenever a user enters a forced account code. If a forced account code is valid, the system provides the user access to an outside line. If a forced account code is invalid, the system denies the user access to an outside line—to dial out, the user must repeat the procedure for entering a forced account code.

■

For faster entry of frequently-used account codes, you can program an account code on an Auto Dial button or as a System or Personal Speed Dial number (but not as a Marked System Speed Dial number). See Auto

Dialing, System Speed Dial Numbers, and Personal Speed Dial Numbers for programming instructions.

Considerations

■

When an account code is entered during a call, the caller on the other end does not hear the touch-tone digits dialed.

■

If SMDR is used, the account code assigned to incoming or outgoing calls prints on call reports. (See “Call Reporting Devices (SMDR)” in Chapter 4 for more information on call reporting.)

■

If an account code is entered for an outgoing call and the call is transferred to another extension, the call report shows the originating extension as the owner of the call. Conversely, if an account code is entered for an incoming call and the call is transferred to another extension, the call report shows the destination extension as the owner of the call.

■

Account codes can be changed during a call. However, only the person who entered the original account code can enter a different account code. SMDR prints changed account codes as follows:

–

For optional or forced account code entry without a Forced Account Code List, the call report prints the last account code entered.

–

For forced account code entry with a Forced Account Code List, the call report prints the last valid account code entered. If the changed account code is not valid, the report prints the original account code.

5-4

Account Code Entry (F12)

■

Programming

To program an Account Code Entry button:

If a Forced Account Code List exists, you can check to see if an account code is valid when entering or changing an account code by pressing



Feature

  1   2 

after entering the account code. If the account code is not

valid, you will hear a denial tone. The AT&T Call Accounting Terminal uses less than 16 digits for an account

code. Refer to the device’s documentation to determine the maximum

digits supported. You can program the Account Code Entry feature code on a button on a

system phone. It is recommended that you use a button with lights. (This

button can be used for optional Account Code Entry or Forced Account Code Entry.)

This feature can be used only from a system phone.

Press



Feature

  0   0  

System Program

 

System Program

 

Central Tel Program

.

Enter the number of the extension to be programmed with this feature. Press a programmable button, preferably one with lights. Press



Feature

  1   2 .

Program another button for this extension or exit programming mode.

Using

To enter or change an optional account code:

From a system phone, if a password is programmed for the system, you must enter it before lifting the handset. (See System Password (#403) for more information.)

After lifting the handset (or while already active on an outside call), press the programmed Account Code Entry button or press



Feature

  1   2 .

If the Account Code Entry button has lights, the green light turns on.

Enter an account code using one of the following methods:

■

Dial it manually using the phone’s keypad

■

Dial a System or Personal Speed Dial number programmed with the

account code

■

Press an Auto Dial button programmed with the account code.

Press the programmed Account Code Entry button or press



Feature

indicate the end of the code.

If the Account Code Entry button has lights, the green light turns off.

Make the call, if you are not already on a call.

5. To change the account code, repeat Steps 2 through 4.

  1   2 

Account Code Entry (F12)

5-5

To enter or change a forced account code:

From a system phone, if a password is programmed for the system, you must

1. enter it before lifting the handset. (See System Password (#403) for more information.)

Lift the handset or press



Spkr

.

Press the programmed Account Code Entry button or press



Feature

If the Account Code Entry button has lights, the green light turns on.

Enter an account code (supplied by your system manager) using one of the

following methods:

■

Dial it manually using the phone’s keypad

■

Dial a System or Personal Speed Dial number programmed with the account code

■

Press an Auto Dial button programmed with the account code.

Press an idle line button:

■

If a Forced Account Code List exists and the account code is valid (or if the Forced Account Code List is empty), you hear outside dial tone. Go to Step 6.

■

If a Forced Account Code List exists and the account code is not valid, you are denied access to the outside line. Verify the account code with your system manager, then repeat this procedure starting from Step 1.

Make the telephone call.

6. To change the account code while on a call:

Press the programmed Account Code Entry button or press



Feature

  1  2 .

  1   2 .

b. c.

5-6

Account Code Entry (F12)

Enter a different account code. Press the programmed Account Code Entry button or press



Feature

  1   2 .

If a Forced Account Code List exists and the account code is invalid,

you hear denial tone. Verify the account code, then repeat Step 7 making sure to enter a valid account code.

Allowed List Assignments (#408)

Description

This System Programming procedure lets you assign up to four Allowed Phone Number Lists to a specific extension.

Related Features

You must use Allowed Phone Number Lists (#407) to create up to four lists of Allowed Telephone numbers before you use this procedure.

Valid Entries

1 =

Assigned to extension

2 =

Not Assigned to extension ✔

Programming

To assign Allowed Phone Number Lists to an extension:

1. Press



Feature

  0   0  

System Program

 

System Program

  #   4   0   8 .

display reads:

AllowTo

Extension:

Enter the number of the extension to be programmed. For example, to

2. program extension 27, press

 2   7 .

The display reads:

AllowTo 27

List No:

Enter the list number (1–4). For example, to select list 1, press  1 .

To assign or unassign the list, press  Next Data  until the appropriate value

displays. At this point:

■

To assign or unassign another list to this extension, press

 Prev Item  until the list number shows on the display. Then repeat Step

4. To program another extension, press

■

 Next Procedure   Prev Procedure  and

begin at Step 2.

Select another procedure or exit programming mode.



Next Item

The



Allowed List Assignments (#408)

5-7

Allowed Phone Number Lists (#407)

Description

This System Programming procedure specifies telephone numbers that users can dial regardless of other dialing restrictions, as long as they have access to an outside line. For example, if you restrict an entire category of calls through Disallowed Phone Number Lists (#404), you can permit calls to a specific number in that category by placing that number on an Allowed Phone Number List. Using this procedure, you can create up to four lists of up to 10 telephone numbers each.

Related Features

■

After completing this procedure, you must use Allowed List Assignments (#408) to assign the Allowed Phone Number Lists to specific extensions.

■

Allowed Phone Number Lists override Disallowed Phone Number Lists (#404) and Outgoing Call Restriction (#401), but not Line Access Restriction (#302) or Night Service Button (#503) with a System Password (#403). (There are other ways of overriding restrictions—see Marked System Speed Dial Numbers, Emergency Phone List Numbers (#406), and System Password (#403) for more information.)

■

The entries you must make to permit or restrict toll calls differ depending on the setting for Toll Call Prefix (#402). This setting tells the system whether a “0” (for operator-assisted calls) or “1” (for direct-dial calls) is required when you make toll calls.

Considerations

■

Each list entry can include up to 12 digits. You can use the wildcard character (by pressing the single digit (it appears as “!” on the telephone display).

■

If you are restricting an extension from placing toll calls, do not place numbers beginning with a “0” on an Allowed Phone Number List for the extension. Once a user is active on an operator-assisted call, the user will be able to avoid dialing restrictions by asking the operator to dial restricted numbers.

Valid Entries

Up to 12 digits including 0–9 and  Hold  (any single digit)

 Hold  button on a system phone) to match any

5-8

Allowed Phone Number Lists (#407)

Examples

The examples below show how you would enter telephone numbers for an

Allowed Phone Number List in Step 4 of “Programming.” When an Allowed List

is assigned to an extension, users can dial numbers on that list, even if the numbers would otherwise be restricted.

■ Specific Telephone Numbers. Enter the phone number exactly as you

■ All Telephone Numbers in One Area Code. The following list entries allow

Programming

To create a list of Allowed Phone Numbers:

would dial it. For example, to allow calls to the number 201 555-1111, make the following entries:

Toll Call Prefix required

–

12015551111

Toll Call Prefix not required

–

2015551111

calls to the 800 area code:

Toll Call Prefix required

–

1800

– Toll Call Prefix not required

800

Press



Feature

  0   0  

At the List No: prompt, enter a list number (1–4). For example, to select the first list, press

At the Entry: prompt, select a list entry (01–10). For example, to select the

3. first entry, press

At the Data

To save the telephone number in memory,

At this point:

■

To enter other phone numbers in this list, press

 1 .

 0   1 .

------------

System Program

 

System Program

  #   4   0   7 .

prompt, enter the first telephone number.

you must press

 Next Item  and repeat



Enter

.

Steps 4 and 5.

■

To change the phone number you just entered, press

 Remove  and

repeat Steps 4 and 5.

■

To delete the phone number you just entered, press

■

To create another list, press  Next Procedure   Prev Procedure  and go to

 Remove .

Step 2.

Select another procedure or exit programming mode.

Allowed Phone Number Lists (#407)

5-9

Answering Calls

Description

This section describes how users can answer calls ringing at their own extensions. Additional features enable users to pick up calls at other extensions—see “Related Features” below.

Related Features

■

A user can answer an outside call, an intercom call, or a transferred call that is ringing at a specific extension or at any extension in a group. For more information, see Call Pickup and Group Pickup.

■

A user can use Direct Line Pickup—Active Line to answer calls on lines not assigned to the user’s phone.

■

A user can join a call in progress at another extension, as long as Privacy is not on for that extension. See Joining.

■

A user can program the Voice Interrupt on Busy Talk-Back feature on a button with lights to respond to a voice interrupt on busy call. Also see

Voice Interrupt On Busy (#312).

Considerations

■ If you are using an MLC-6 cordless phone, make sure the handset is on

before using the following instructions.

■

There are several ways to access a line for answering calls:

On either a system phone or a standard phone, lift the handset to answer

–

a ringing call (if more than one call is ringing at a system phone, you get the call that has been ringing for the longest time).

On a system phone, press a specific line or

–

 Intercom  button. You can

also use Direct Line Pickup to pick up a ringing or held call, or to join an active call, by dialing

–

On a standard phone, you can use Direct Line Pickup to pick up a



Intercom

  6   8 

and the two-digit line number

ringing or held call, or to join an active call on a specific line: at intercom dial tone, dial

 6   8 

and the two-digit line number.

5-10

Answering Calls

How to Answer Calls Ringing at Your Extension

System Phone

You can answer a call on any line that is ringing, or select a specific line if more than one is ringing:

■

When the telephone is ringing, lift the handset.

You are connected to the incoming call. If more than one line is ringing, you are connected to the line that has been ringing for the longest time. If the call is an intercom call and you have a display phone, the caller’s extension number briefly appears on your display.

■

To answer a call on a specific line:

Press the line button for the line you want to answer.

1. Lift the handset or press



Spkr

.

You are connected to the call.

To answer a call when you are already on a call:

■

Press



Hold

.

The call you are on is placed on hold.

Press the button for the new call.

You are connected to the new call.

To return to the first call, put the second call on hold and press the line button for the first call.

■

To answer a voice-signaled call (your phone beeps and you hear the caller’s voice):

––If the microphone is on, you can speak after the beep.

If the microphone is not on, press



Mic



or lift the handset.

Standard Phone

When the telephone is ringing, lift the handset.

You are connected to the incoming call.

Answering Calls

5-11

Auto Dialing

Description

This Telephone Programming procedure lets users dial outside numbers, extension numbers, feature codes, or account codes with a single touch, by pressing a programmed button. An Auto Dial number can be stored on any programmable button (a button with no line assigned) on a system phone.

Related Features

■

To set up a Fax Management button, program the fax extension number on an Auto Dial button with lights. Special light patterns on the Auto Dial button for the fax extension indicate fax machine status. Chapter 4 provides more information on using a Fax Management button. Identify fax extensions using Fax Machine Extensions (#601).

■

You can include special functions, such as a Pause, in the Auto Dial number. Special Dialing Functions provides more information on these functions.

Considerations

■

If you program an extension number on a button with lights, the lights show calling activity at the extension (see “Lights” in Chapter 3). Similarly, you can connect an MLS-CA24 Intercom Autodialer to the system phones at extension 10 and 11 to have Auto Dial buttons for all of the extensions in your system (up to 24); this lets the users at extensions 10 and 11 transfer calls to any extension by pressing one button, and view call activity at all extensions with a glance.

■

Each user can have only one Auto Dial button—either on the system phone or on the MLS-CA24 Intercom Autodialer—for another extension in the system.

■

When programming emergency numbers for Auto Dialing and/or making test calls to those numbers, you should: 1) Remain on the line and briefly explain to the dispatcher the reason for the call before hanging up and 2) Perform such activities in the off-peak hours, such as early morning or late evening.

Auto Dial buttons do not override dialing restrictions for an extension.

■

MLS-6 and MLC-6 system phones only have four buttons available for lines

■

and/or features.

■

For PBX or Centrex systems that require a dial-out code to make calls outside the PBX or Centrex system, include the dial-out code on an Auto Dial button for a number outside the PBX or Centrex system.

■

Auto Dial buttons can be programmed only on system phones.

5-12

Auto Dialing

Examples

The examples below show some possible entries for an Auto Dial number in Step 4 of “Programming.”

■

Programming

To program an Auto Dial button:

Outside Phone Number. Enter the phone number (up to 20 digits) exactly as you would dial it. For example, to program 555-2398, press

 5   5   5   2 

 3   9   8 .

Extension Number. Press the left  Intercom  button and enter the two-digit extension number. Include a

 ✴  before the extension number to program

the Auto Dial button to voice signal an extension. For example, to program extension 20 for voice signaling, press



Intercom

  ✴   2   0 .

The display

reads:

Intercom *20

Feature Code. Enter the appropriate code. For example, to program the

Call Forwarding feature code on a button, press

Press



Feature

  0   0  

System Program

 



Feature

System Program

  1   1 .

 

Central Tel Program

.

Enter the number of the extension to be programmed. Press a programmable button.

Using

Enter an outside phone number, feature code, account code, or PBX/Centrex feature access code; or press left

Repeat Steps 3 and 4 to program additional Auto Dial buttons, or exit

 Intercom  and enter an extension number.

programming mode.

From a system phone, to dial an outside number or extension number (you can

lift the handset or press

If you want to call on a specific line, press the line button (or press  Intercom 

 Spkr , but you do not have to do so):

 8  and the two-digit line number) before pressing the Auto Dial button.

If you did not lift the handset, the lights next to



Spkr



and



Mic



go on, and

you are active on the speakerphone.

Press the Auto Dial button on which the outside number or extension number is programmed.

The system automatically selects a line if you did not specify one, turns on

the speaker (if you did not lift the handset), and dials the Auto Dial number. The number being dialed will show on a display phone.

To use an Auto Dial button programmed with a feature code or account code, follow the directions for the feature you want to use.

Auto Dialing

5-13

Automatic Extension Privacy (#304)

Description

This System Programming procedure lets you either allow users to join active

calls at an extension or prevent users from joining active calls at the extension.

When Automatic Extension Privacy is Assigned for an extension, other users

cannot join active calls at that extension. This feature is typically used for standard phones and extensions connected to fax machines, modems, and

credit card scanners, which make and receive data calls that should not be

interrupted.

Related Features

■

To manually change an extension’s Privacy state, users can program the Privacy feature on a button with lights. Users can then press the Privacy button to activate the feature (green light on) or deactivate the feature (green light off) when they want someone to join a call at their extension. (If

Automatic Extension Privacy is Assigned at an extension, the green light is

lit automatically after programming the Privacy button to indicate that Privacy is currently active. If this is the case, and the Privacy button is pressed, the feature is deactivated. To activate Privacy again, you must press the button.)

This feature applies only to active calls. Any user can retrieve a held call

■

unless Exclusive Hold is used.

Considerations

■

as an answering machine, voice messaging system, or PARTNER

Attendant—make sure Automatic Extension Privacy is Not Assigned for the

auxiliary equipment extension.

■ Standard phones and system phones without a programmed Privacy button

cannot override this feature once it is assigned to an extension.

Valid Entries

1 =

Assigned Not Assigned ✔

2 =

Programming

To change the Automatic Extension Privacy setting for an extension:

If you want to be able to intercept calls routed to an auxiliary device—such

Press



Feature

  0   0  

System Program

 

System Program

  #   3   0   4 .

Enter the number of the extension to be programmed. For example, to program extension 16, press

 1   6 .

To assign or unassign Automatic Extension Privacy for the extension, press

 Next Data  until the appropriate value displays.

To program another extension, press



Next Item





Prev Item



until the extension

number shows on the display. Repeat Step 3.

5-14

Select another procedure or exit programming mode.

Automatic Extension Privacy (#304)

Automatic Line Selection

Description

This Telephone Programming procedure determines the line a user is connected to after lifting the handset to make a call. When the user picks up the handset, the system looks for lines in the order specified by this procedure and selects the first available line. For example, if you specify outside lines first for an extension, but all outside lines are busy, the user will hear the intercom dial tone after lifting the handset.

Related Features

■

To copy the Automatic Line Selection setting (as well as other system settings) to other extensions, you can use Copy Settings (#399).

■

If Forced Account Code Entry (#307) is assigned to an extension, Automatic Line Selection is not active for that extension. This means the user must manually select a line after entering a required account code.

Considerations

■

This feature must be programmed from extension 10 or 11 only, using Centralized Telephone Programming. Individual users cannot program this feature directly.

■

You should program Automatic Line Selection when you first enter Centralized Telephone Programming, before programming any other features. However, if you want to program both Automatic Line Selection and Extension Name Display (which also must be programmed when you first enter Centralized Telephone Programming), first program Automatic Line Selection, then exit and re-enter Centralized Telephone Programming again to program Extension Name Display.

■

For standard touch-tone or rotary phones, or for any phone used mainly to call other extensions, program the extension to select intercom first.

■

Valid Entries

Outside lines 01–12, Left Intercom ✔

For combination extensions, the automatic line selection for both devices (including a standard device) follows the automatic line selection for the extension.

For hotline and doorphones, program the extension to select only the intercom, with no outside lines in the selection sequence.

You do not need to include all available lines for an extension, only the ones you want the system to search through and connect automatically.

Automatic Line Selection

5-15

Examples

System Phone

With Automatic Line Selection at its factory setting, the system first searches to find an idle outside line in numerical order (starting with line 1). Then, if all outside lines are busy, the system searches for an idle intercom line. This order can be changed, however, to accommodate your business needs. For example, a telemarketing firm with a WATS line (line 5) to reduce telephone expenses would set Automatic Line Selection for all telemarketers’ extensions to “5, 1, 2, 3, 4, Intercom.” This way the WATS line would be selected first.

Standard Phone

If a standard phone user intends to place intercom calls and access system features, Automatic Line Selection for his or her extension should be set to intercom first for proper operation. For example, the setting for a standard phone in a lobby, used for internal calling or making local calls on line 1, would be set to “Intercom, 1.”

Programming

To program Automatic Line Selection for an extension:

Press



Feature

  0   0  

System Program

 

System Program

 

Central Tel Program

.

Enter the number of the extension to be programmed for Automatic Line Selection.

Press

 ✴   ✴ 

Press the line and/or left intercom buttons in the desired order. For each button pressed, the display reads:

Auto Line Select

To exit Automatic Line Selection, press

Press  Central Tel Program  and enter a new extension number or exit

 ✴   ✴ .

programming mode.

5-16

Automatic Line Selection

Automatic VMS Cover (#310)

Description

This System Programming procedure automatically routes an extension’s unanswered intercom and transferred calls to the Call Answer Service of the

voice messaging system after three rings, so callers can leave a message.

Related Features

■

To turn VMS Cover on and off, users can program a VMS Cover button with

lights. Users can then press the VMS Cover button to activate (green light

on) or deactivate (green light off) VMS Cover.

■

If an extension has VMS Cover and Do Not Disturb active, intercom and transferred calls go directly to the voice messaging system without ringing the extension.

■

If an extension has VMS Cover and Call Forwarding active, calls ring at the

forwarding destination; they are not covered by the voice messaging system

Considerations

This feature applies only if you have a voice messaging system.

Valid Entries

1 = 2 =

Programming

To change the Automatic VMS Cover setting for an extension:

Assigned Not Assigned ✔

Press



Feature

  0   0  

System Program

 

System Program

  #   3   1   0 .

display reads:

AutoVMS Cover Extension:

Enter the number of the extension to be covered by the voice messaging system. For example, to program extension 11, enter

To assign or unassign Automatic VMS Cover, press

 1   1 .



Next Data



until the

appropriate value displays. To program another extension, press



Next Item





Prev Item



until the extension

number shows on the display. Then repeat Step 3. Select another procedure or exit programming mode

The

Automatic VMS Cover (#310)

5-17

Background Music (F19)

Description

This feature provides background music through the speaker of an idle system

phone (except the MLC-6) for a user’s work area. Background Music plays the recorded material from the Music On Hold audio source.

Related Features

Background Music is available only if Music On Hold (#602) is active and an

audio source is connected to the processor module.

Considerations

If you use the Background Music feature to broadcast certain copyrighted

■

music or material, including songs or other material from radio broadcasts, you may be required to obtain the permission of the copyright owner. One

way to obtain permission is to contact ASCAP, BMI, and/or similar performing rights organizations, to obtain a license. AT&T disclaims any liability arising out of the failure to obtain such a license, if required. For

alternative (usually pre-licensed) sources of music to use with this feature,

you may wish to contact Telephonetics International, Inc. at 1-800-446-5366.

■

Background Music stops when a user makes or answers a call, but resumes when the phone becomes idle again.

■

Programming

To program a Background Music button:

4. Press

If a system phone and a standard phone with a message waiting light are

connected in a combination extension, the standard phone’s message

waiting light will not light if Background Music is on at the system phone. You can program a Background Music button on a system phone to use the

feature with one touch. A button with lights is recommended.

This feature is not available on MLC-6 or standard phones.

Press



Feature

  0   0  

System Program

 

System Program

 

Central Tel Program

.

Enter the number of the extension to be programmed with this feature. Press a programmable button, preferably a button with lights.



Feature

  1   9 .

Program another button for this extension or exit programming mode.

5-18

Background Music (F19)

Using

To turn Background Music on:

From a system phone (except an MLC-6), press the programmed button or press



Feature

  1   9 .

If the system phone is idle, you hear background music. If the Background Music button has lights, the green light turns on.

To adjust the volume of Background Music, use the system phone’s volume

control buttons while listening to the background music. To turn Background Music off: Press the programmed button or press



Feature

  1   9 

again.

If the Background Music button has lights, the green light turns off.

Background Music (F19)

5-19

AT&T Partner Plus R3-1 Programming and Use

Specifications and Main Features

Frequently Asked Questions

User Manual

About This Guide

Purpose

Terminology

How to Use This Guide

Product Safety Statements

How to Comment on This Guide

Overview

Important Safety Instructions

Features and Capabilities

System Components

Control Unit

System Modules

System Capacity

Telephones

System Telephones

Intercom Autodialers

Standard Telephones

Auxiliary Equipment

Requirements

Connecting Standard Devices

Programming

Overview

Hardware Considerations

Initial System Setup

Setting the System Clock

Assigning Lines

Customizing Extensions

Copy Settings

Changing Settings after Installation

Changing the System Clock

Adding New Lines

Adding New Extensions

Swapping Extensions

Recall Setting

Dialing Restrictions

Speed Dial and Auto Dial Numbers

System Programming Options

Speed Dialing

Dialing Restrictions and Permissions

Restricting Access to Outside Lines

Controlling Calls on Outside Lines

Overriding Dialing Restrictions

Summary

Setting Up Groups of Extensions

Setting Up Auxiliary Equipment

Hospitality Features

Using System Programming

The Programming Overlays

Programming Mode

Changing Programming Type

Telephone Programming Options

Automatic Line Selection

Extension Name on Display

Line Ringing

Personal Speed Dialing

Programming Telephone Buttons

Programming a Receptionist’s Extension

Call Handling Options

Button Programming

Using Telephone Programming

Telephone Models

Using Centralized Telephone Programming

Changing Programming Type

Using Extension Programming

Learning About Telephones

System Telephones

Buttons and Indicators

Lights

Ringing Patterns

Dial Tones

Using the Handset, Speaker, and Microphone

Hands-Free Answer on Intercom (HFAI)

Voice Interrupt on Busy Calls

Speakerphone Performance Tips

Standard Telephones

Ringing Patterns