The instructions below are both table and wall installation.
1. Choose a spot near an electrical outlet and a telephone jack.
•
This phone requires a modular telephone jack and a standard electrical outlet (110v AC).
•
The outlet should not be controlled by a wall switch: if the switch is ever turned off, the phone will not
operate.
2.
Install the handset antenna.
in the top of the handset. Turn the antenna clockwise to make sure the tip is set in place, and continue
until the rubber is snug against the top of the handset. Do not overtighten.
3. Install the handset battery.
•
Remove the battery compartment cover on the handset by pressing on the indentation and sliding the
cover downward.
•
Plug the battery pack cord into the handset, and rest the cords on top of the battery pack.
•
Replace the cover by sliding it on its track up over the battery compartment until it snaps firmly in
place.
4.
Set the Dial Mode Switch
pulse/rotary service.
5.
Set the Ringer Switch.
6.
Connect the telephone line cord.
of the base. (If you are wall mounting the phone, wrap the excess cord around the tabs under the base.)
Plug the other end of the line cord into a modular jack. Make sure the plug snaps firmly in place.
7.
Mount the base on the wall.
standard wall jack will fit into the holes on the bottom of the base. Slide the base down onto the knobs
until it locks into place.
8.
Plug in the power cord.
9.
Charge the handset batteries for 10 hours.
base goes on to show the handset is in the right position to charge the batteries.
10.
Check for dial tone.
Check for dial tone by pressing PHONE; the PHONE light should go on and you should hear a dial
tone.
After the batteries are charged, pick up the handset and extend the base antenna.
Slide the metal tip of the handset antenna straight down into the opening
to Tone if you ha ve touch tone servi ce, or PULSE if you have dial
Set the switch to ON (the phone will ring) or OFF (the phone will not ring).
Plug one end of the telephone line cord into the jack on the top side
(Wall Mounting Only) Hold the base so that the mounting knobs on the
Plug the AC adapter on the power cord into an electrical outlet.
Place the handset in the base. The Charging light on the
Operation
Making a call
1. Press PHONE, and wait for the PHONE light to go on.
2. When you hear a dial tone, dial the number.
Answering a Call
•
If the handset is in the base, lift the handset. The phone light goes on, and the call is connected.
•
If the handset is away from the base, press phone. The PHONE light goes on, and the call is connected.
Ending a Call
•
IF you are near the base, place the handset in the base.
•
If you are away from the base, press OFF.
Redial
The last number dialed on this phone is stored in redial memory until you dial another number.
1. Press PHONE, and wait for the PHONE light to go on.
2. When you hear a dial tone, press REDIAL>
Handset Volume Control
To increase the sound level of a call, move the handset Volume control to HI.
To decrease the sound level, move the handset Volume control to LO.
Temporary Tone
If you have dial pulse (rotary) service, this feature allows you to enter codes, or tones needed to operate
answering machines, or use electronic banking services, calling cards, and other special services. This
feature will operate most special services; however, some services may actually require a touch tone line.
To be sure, ask the company that provides the special service.
: If you have touch to ne service, you do not need to use t he Temporar y Tone feature.
Note
1. Dial the call, then press *. Any buttons pressed after this sends tone signals.
2. After you hang up, the phone automatically returns to dial pulse (rotary) dialing.
Page
The page feature allows you to signal someone at the handset from the base.
•
Press PAGE/FIND on the base. A 3-part paging tone will sound at the handset.
Find
This feature is useful if you misplace the handset.To locate the handset using this feature: Press and hold PAGE/FIND on the base for approximately three
seconds. A rep eating paging tone is sounded in the handset.
To cancel the Find feature, press OFF on the handset or PAGE/FIND on the base.
: The find feature will turn itself off in approximately 3 minutes if you haven’t turned it off before then.
Note
Mute
Mute allows you to hear your caller, but prevents the calls form hearing you.While on call:
•
Press MUTE and the phone lightly slowly flashes.
To continue your conversati on:
•
Press MUTE again and the phone light will be steady.
Special Telephone Services
If you subscribe to special local telephone company services like Call Waiting or Call Forwarding, you can
access them by pressing PHONE whenever you would press the switchhook on a regular phone. This is like
the Flash feature on some other phones.
Memory
This cordless phone can store nine telephone numbers that you can dial just by pressing MEMORY and one
of the number buttons.
Storing a Number in Memory
1. Make sure the handset is OFF.
2. Press MEMORY. The phone light will flash.
3. Enter the phone number (up to 16 digits).
4. Press Memory
5. Press any number button from 1 – 9 for the memory location where the number is to be stored.
6. A three – part tone confirms that the number was stored properly. If you hear a long buzzing tone, or
nothing at all, press OFF, then follow the steps above to store the number again.
: You may choose to store emergency numbers in memory locations. The manufacturer assumes no
Note
responsibility for customer reliance upon this memory feature.
Dialing a Number in Memory
1. Press PHONE.
2. Press MEMORY.
3. Press the number button (1 – 9) you assigned to the number you’re calling.
Memory Card
There is a memory card with an erasable surface located on the base to record names or telephone numbers
of the numbers stored in memory locations.
To write on the memory card, remove the plastic cover by inserting a pointed object in the hole and gently
prying the cover up until it pops out.
: The numbers stored in memory might be lost when you change the handset batteries or if the
Note
batteries run down completely: if this happens, you’ll need to store the numbers again.
Replacing a Stored Number
You can replace a stored number by storing a new number in its place.
Storing a Pause In a Memory Dial Number
If this phone is connected to a switchboard you might have to dial an access number (usually 9) to get
outside line. You can store the access number and a pause in the dialing sequence: the pause allows the
switchboard enough time to get an outside line dial tone.
1. When storing a memory number (see above), press and hold the number button of the digit that comes
just before the pause, until a second beep is heard. This inserts a 2 – second pause.
2. You can insert a long pause by continuing to press and ho l d the number button of the digit that comes
before the pause. A beep is heard for each 2 – second pause inserted.
: Each pause you store is counted as a digit. You can store up to 16 digits in each memory location.
Note
For Example, to store 9, PAUSE, 555-1234 in memory location 3: Press MEMORY, 9, hold until the beep.
Then press 5551234 MEMORY 3.
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.