A-Trend ATC-1535 ATC-1535 User Manual

Download

Table of Contents

JUMPER LOCATION DIAGRAM . . . . . . A

CONNECTOR LOCATION DIAGRAM . . B

....................................

CHAPTER 1 INTRODUCTION 2

1-1 SYSTEM FEATURES.......................... 3

1-2 CHECK LIST OF THE PACKING . . . . . . . . . . . . . . . . 4

CHAPTER 2 INSTALLATION 5

2-1 CPU INSTALLATION .......................... 5

2-2 SYSTEM MEMORY INSTALLATION

2-3 SRAM INSTALLATION ........................ 7

2-4 OTHER JUMPERS SETTING . . . . . . . . . . . . . . . . . . . 8

CHAPTER 3 AWARD BIOS SETUP 10

3-1 UPDATE BIOS PROCEDURES

3-2 AWARD SYSTEM BIOS CONFIGURATION SETUP . 12

APPENDIX A

CHAPTER 1

INTRODUCTION

This manual introduce how to set-up and upgrade this mainboard. It's an overview of the layout and features of the mainboard, and provides necessary information for you to change the configuration or system environment.

This manual is divided into two sections :

PART ONE includes page A and page B about this mainboard's layout diagram. You should refer them when you set-up and upgrade your system hardware.

PART TWO includes three chapters as following: Chapter 1 is an overview of the mainboard features and this mainboard's packing contents.

Chapter 2 explains how to upgrade and change hardware configuration including memory, CPU, and lists jumper settings and connectors.

Chapter 3 is the user's guides of AWARD BIOS setup utility, and Flash ROM BIOS update procedures. The menu showed in this chapter are default setting.

Your system dealer will set up the mainboard according to your demand of computer. It means your mainboard's current setting may not be the same as the defaults shown in this user's manual. If you would like to change your configuration, please ask your dealer firstly, be sure this will not against your system warranty. Or ask for your dealer to do it for you.

1-1 SYSTEM FEATURES

Supports INTEL 75/90/100/120/133/150/166MHz and later

Pentium CPUs with one ZIF socket 7.

INTEL TRITON chipset and Winbond high-speed multi I/O chipset. Supports Asynchronous SRAM sockets for eight SRAM chips

and one Synchronous COAST (Cache On A STick) slot for Pipeline Burst SRAM module.

Write Back / Write Through Level 2 external Asynchronous

cache using mixed mode SRAM with size of 256KB / 512KB.

Using four 72-pin SIMM sockets, provides two banks of 64-bit

wide path up to 128MB addressing page mode DRAMs.

Supports EDO DRAM and mixing of EDO SIMMs with fast page

mode DRAM SIMMs among different banks.

Four PCI master slots and three 16-bit ISA slots. Dual IDE connectors support up to four devices in two channels

for connection of high capacity hard disk, CD-ROM, tape backup etc.. PCI IDE controller supports PIO mode 0 to mode

4. Auto detecting of installed IDE devices through BIOS utility.

: "True" Green power management for CPU stop clock state

On board high-speed Multi-I/O connectors:

one FDC port supports two devices up to 2.88MB two 16550A fast UARTs compatiable serial ports one EPP/ECP mode parallel port The selections of all primary and secondary ISA addressing of COM1 - 4, LPT 1-3 and FDC disable or enable from BIOS SETUP configuration please refer to "CHIPSET FEATURES

SETUP" in the chapter three.

Board dimension : 220mm x 280mm , 8.66" x 11.02"

REMARK

Intel™ is a registered trademark of Intel Corporation. MS-DOS is a registered trademark of Microsoft Corporation.

IBM™ ,IBM PC™ ,I BM AT™ and IBM XT™ are registered trademark of

International

Business Machines Corporations. All other brands and product names are trademarks registered trademarks of their

respective companies.

1-2 CHECK LIST OF THE PACKING

The mainboard comes securely packed in a durable box and shipping carton. If any of the above items are missed or damaged, please contact your system dealer.

Each mainboard containing:

Q'TY Description 1 Mainboard : ATC-1535.

1 Diskette : Enhanced IDE driver (3.5"). 1 Cable : Enhanced IDE connector. 1 Cable : F.D.D. connector. 1 Cable : Serial port. 1 Cable : Serial/Parallel. 1 Manual : User`s manual.

NOTE : Leave the mainboard in its original packing until you are

ready to install it.

CHAPTER 2 INSTALLATION

2-1 CPU INSTALLATION

ATC-1535 can support INTEL Pentium 75/90/100/120/133/150 /166MHz and later CPUs. For installation, please notice CPU pin 1 must align with the ZIF socket 7 Pin 1 location.

2-1-1 CPU TYPE SELECTION

INTERNAL CPU CLOCK

75MHz open open close close 50x1.5 90MHz open open close open 60x1.5 100MHz open open open close 66x1.5 120MHz open close close open 60x2.0 133MHz open close open close 66x2.0 150MHz close close close open 60x2.5 166MHz close close open close 66x2.5 ¡/ If you use the higher internal CPU clock in the future, please

JP7 JP8 JP10 JP11 Ext.x Fre.

refer to 2-1-2 for jumper setting.

2-1-2 CPU CLOCK SETTING

T he following setting is for CPU speed higher than 166MHz.

EXTERNAL CPU CLOCK

JP10 JP11 50(MHz) close close 60(MHz) close open 66(MHz) open close

INTERNAL CPU CLOCK INTEL EXTERNAL CLOCK X 1.5 INTEL EXTERNAL CLOCK X 2.0 INTEL EXTERNAL CLOCK X 2.5 INTEL EXTERNAL CLOCK X 3.0

JP7 JP8 open open open close

close close close open

2-2 SYSTEM MEMORY INSTALLATION

ATC-1535 provides four 72-pin SIMM sockets for system memory expansion from 4MB to 128MB. These four SIMMs are arranged to two banks, Bank0 (SIMM 1,2) and Bank1(SIMM 3,4), please refer to page A,B. Each bank provides 64-bit wide data path. There are no jumper setting required for the memory expansion, and it will be detected by BIOS automatically.

This mainboard can accept either Fast Page Mode or EDO Mode (Extended Data Out) DRAM, with a speed at least 70 nanosecond. You should plug DRAM modules into two sockets (same bank) or four sockets at one time. Each pair of modules must be the same size, type and speed; no matter single-side or double-side module. This mainboard supports mixing of EDO SIMMs with fast page mode DRAM SIMMs among different banks.

¡/ System Memory Combinations Options ¡/

BANK0 BANK1 Total Memory

SIMM1,2 SIMM3,4 SIMM1-4

2MBx2 - 4MB

2MBx2 4MB

4MBx2 - 8MB

- 4MBx2 8MB

8MBx2 - 16MB

- 8MBx2 16MB

4MBx2 4MBx2 16MB

16MBx2 - 32MB

- 16MBx2 32MB

8MBx2 8MBx2 32MB

32MBx2 - 64MB

- 32MBx2 64MB 16MBx2 16MBx2 64MB 32MBx2 32MBx2 128MB

2-3 SRAM INSTALLATION

ATC-1535 can use standard Async. SRAM in socket (U29 to U36) or Sync. Pineline Burst SRAM module in COAST slot. This mainboard uses Mixed Mode (5V in and 3.3V out) SRAM. The setting is according to the mode you choiced, and to the size you used.

TAG SRAM is the same socket for both of SRAM types ( location U21). Most of Pipeline Burst SRAM modules will be included a TAG

SRAM on board, if you purchase the module without TAG SRAM, you should put a TAG SRAM into U21. For the standard Async. SRAM you can use write-back or write through Level 2 SRAM.

You can use Async. SRAM or Sync. SRAM (Pipeline Burst) in a time, there are no jumper setting and BIOS value adjustments for changing the SRAM type. If you would like to change your SRAM type from Sync. to Async. or from Async. to Sync., you have better to move original SRAM out.

Following setting are only for using Async. SRAM chip.

¡/ Async. SRAM Size Jumper Setting :

cache size JP13 JP14 JP16

256KB 1-2 1-2 1-2 512KB 2-3 2-3 2-3

¡/ System Memory Combinations Options ¡/

SRAM TYPE SRAM SIZE DATA SRAM TAG SRAM

Asynchronous 256KB 32K8 x 8pcs 8K8,16K8 or

32K8 x 1pc

512KB 64K8 x 8pcs 16K8 or 32K8

x 1pc

Synchronous 256KB 32K32 x 2pcs

on board

8K8,16K8 or 32K8 x 1pc

¡/ JP17 Setting is for Async.SRAM Voltage Type :

JP17 1-2 Mixed Mode¡6

2-3 3.3V

¡6 Currently ATC-1535 only supports Mixed Mode type.

2-4 OTHR JUMPERS AND CONNECTORS

The location of following jumpers and connectors please refer to page A and B.

Connector Function Remark

J7 IDE LED Pin 2 is '+' **

J8 Hardware PMU Power Management Unit J14 K-LOCK KeyLock Connector J15 SPK PC Speaker Connector J16 T urbo LED Pin 1 is '+' ** J18 Reset Hardware Reset Switch

¡/Turbo Switch is fixed to open mode for the TURBO function.

** If you plugged wrong side, the light will be weaker, but the IDE

devices are still workable.

Jumper Function Remark

JP9 ATBUS CLK 1-2: PCI CLK/3 for external

CPU clock 50MHz 2-3: PCI CLK/4 for external

CPU clock 60, 66MHz

JP6 CMOS 1-2: Normal¡6

2-3: Clear CMOS

JP5 M/C Open: Color¡6¡6

Close: Mono

¡6is default setting ¡6¡6is factory default setting (fixed)

Connector Function Remark

CN1 PS/2 Mouse Optional CN2 COM 1 Serial Port Cable

Connector

CN3 COM 2 Serial Port Cable

Connector

CN4 FDC Floppy Disk Drive Cable

Connector

CN5 LPT Parallel Port Cable

Connector

CN7 IDE1 Primary 1st IDE Drive Cable

Connector

CN6 IDE2 Secondary 2nd IDE Drive Cable

Connector

¡/ When you plug a cable into the above I/O connectors, you should let the pin 1 edge of the cable is at the pin 1 end of the connector.

CHAPTER 3 AWARD BIOS SETUP

This chapter explains the system BIOS setup, and how to update

new BIOS. All BIOS screens showed on following pages are default values, your system dealer will set up these values according to your demand of computer.

ATC-1535 uses Flash ROM (5V or 12V) to make BIOS easier to be updated by the floppy disk-based program. and to committe MicroSoft Windows 95 plug & play feature.

There are two jumpers should be set for Flash ROM and BIOS.

¡/ JP12 Setting is for Flash ROM VoltageType

1-2: + 5Volt¡6 ¡6 2-3: +12Volt

¡6 ¡6is factory default setting (fixed)

¡/ JP6 Setting is for Update System BIOS

1-2 NORMAL¡6 2-3 CLEAR CMOS

¡6is defaule setting

3-1 UPDATE BIOS PROCEDURES

If the BIOS should be updated, you can get the new BIOS diskette from your system dealer. The BIOS diskette is included 3 files they are "sst.exe", this BIOS update utility; the new version BIOS file with a file name about its version number; and a text file, a readme file. The update procedures are as following:

1. Boot from hard disk drive C, then change to floppy A (or B).

2. Insert the updated diskette to drive A (or B), press "sst" to run the BIOS update utility.

3. Press new BIOS file name to install the new BIOS.

4. Follow the utility status to back up your existing system BIOS to a file named "bios. old" file. Then the original BIOS will be saved in diskette.

5. Press "Y" when the screen shows " Are you sure to program (Y/N) ?" Now the BIOS updated is finished.

6. Then exit the utility and turn off the power, set JP6 to '2-3' to clear the CMOS. After 10 seconds, set JP6 to '1-2', become the normal status.

7. Turn the power on and test your system workable or not.

8. If your installation fail, re-install the new BIOS again as above procedures. Or re-install original BIOS from the back up file (type file name "bios. old" file ) as above procedures. Or call your system dealer for help.

3-2 AWARD SYSTEM BIOS CONFIGURATION SETUP

Following pages explain how to set up the system configuration (CMOS) under the AWARD BIOS. The SETUP program is stored in the Read-Only-Memory (ROM) on the mainboard. To do the SETUP procedure, press the <Del> key when the system is booting up. The following main menu will appear. Please select " STANDARD

CMOS SETUP" to enter the next screen.

ROM PCI/ISA BIOS (2A59CA29)

CMOS SETUP UTILITY

AWARD SOFTWARE, INC. STANDARD CMOS SETUP PASSWORD SETTING BIOS FEATURES SETUP IDE H DD AUTO DETEC TION CHIPSET FEATURES SETUP SAVE & EXIT SETUP POWER MANAGEMENT SETUP EXIT WITHOUT SAVING PCI CONFIGURATION SETUP LOAD BIOS DEFAULTS LOAD SETUP DEFAULTS ESC: Quit :Select Item F10: Save & Exit Setup (Shift) F2 : Change Color

Tim e, Date, Hard Disk Type .....

The section on the bottom of the main menu explains how to control this screen. The other one section displays the items highlighted in the list.

This screen records, some basic hardware information, set the system clock and error handling. These records can be lost or corrupted if the on-board battery is fail or weak.

ROM PCI/ISA BIOS (2A59CA29)

CMOS SETUP UTILITY

Tim e, Date, Hard Disk Type .....

ROM PCI/ISA BIOS (2A59CA29)

STANDARD CMOS SETUP

Date (mm:dd:yy) : Wed, Dec 6 1995

Time(hh:mm:ss) : 3 :

37 : 7

HARD DISKS TYPE SIZE CYLS HEAD PRECOMP LANDZ SECTOR

MODE

Primary Master : AUTO 0 0 0 0 0 0

AUTO

Primary Slave : AUTO 0 0 0 0 0 0

AUTO

Secondary Master : AUTO 0 0 0 0 0 0

AUTO

Secondary Slave : AUTO 0 0 0 0 0 0

AUTO

Drive A : 1.44M, 3.5 in. Bas e Mem ory :

AWARD SOFTWARE, INC.

640K

Drive B : None Extended memory : 64512K

Other Memory :

384K

Video : EGA/VGA ---------------------------------------------

---

Halt On: All Errors Total Memory :

65536K

ESC : Quit :Select Item PU/PD/+/- : Modify

F1 : Help (Shift) F2 : Change Color

This screen is a list of system configuration options. Some of them are defaults

required by the mainboard's design, others will be

depended on the features of your system.

ROM PCI/ISA BIOS (2A59CA29)

CMOS SETUP UTILITY

AWARD SOFTWARE, INC. STANDARD CMOS SETUP PASSWORD SETTING BIOS FEATURES SETUP IDE HDD AUTO DETECTION CHIPSET FEATURES SETUP SAVE & EXIT SETUP POWER MANAGEMENT SETUP EXIT WITHOUT SAVING PCI CONFIGURATION SETUP LOAD BIOS DEFAULTS LOAD SETUP DEFAULTS ESC: Quit :Select Item F10: Save & Exit Setup (Shift) F2 : Change Color

Tim e, Date, Hard Disk Type .....

ROM PCI/ISA BIOS(2A59CA29) BIOS FEATURES SETUP AWARD SOFTWARE , INC. Virus Warning : Disabled Video BIOS Shadow : Enabled

CPU Internal Cache : Enabled C8000-CBFFF Shadow : Disabled

External Cache : Enabled CC000-CFFFF Shadow : Disabled

Quick Power On Self Test : Disabled D0000-D3FFF Shadow : Disabled

Boot Sequence : A, C D4000-D7FFF Shadow : Disabled

Swap Floppy Drive : Disabled D8000-DBFFF Shadow : Disabled

Boot Up Floppy Seek : Enabled DC000-DFFFF Shadow : Disabled

Boot Up NumLock Status : On

Boot Up System Speed : High

Gate A20 Option : Fast

Memory Parity Check : Enabled Esc : Quit :Select Item

Typem ati c Ra te Se tting : Disabled F1 : Help PU/PD/+/- : Modify

Typematic Rate(Chars/Sec) : 6 F5 : Old Values (SHIFT)F2 : Color

Typem ati c De lay(Ms ec) : 250 F6 : Load BIOS Defau lts

Security Option : Setup F7 : Load Setup Defaults

PCI/VGA Palette Snoop : Disabled

This screen controls the se tting for the chipset on the mainboard.

ROM PCI/ISA BIOS (2A59CA29)

CMOS SETUP UTILITY

AWARD SOFTWARE, INC. STANDARD CMOS SETUP PASSWORD SETTING BIOS FEATURES SETUP IDE HDD AUTO DETECTION CHIPSET FEATURES SETUP SAVE & EXIT SETUP POWER MANAGEMENT SETUP EXIT WITHOUT SAVING PCI CONFIGURATION SETUP LOAD BIOS DEFAULTS LOAD SETUP DEFAULTS ESC: Quit :Select Item F10: Save & Exit Setup (Shift) F2 : Change Color

Tim e, Date, Hard Disk Type .....

ROM PCI/ISA BIOS (2A59CA29)

CHIPSET FEATURES SETUP

AWARD SOFTWARE, INC. DRAM RAS# Precharge Time : 4 PCI Concurrency : Enabled DRAM R/W Leadoff Timing : 8/6* PCI Streaming : Enabled DRAM RAS To CAS Delay : 3* PCI Bursting : Enabled DRAM Read Burst Timing : x2222* Onboard FDC Control : Enable DRAM Write Burst Timing : x3333* Onboard Serial Port 1 : COM1/3F8 Syste m BIOS Ca cheable : Disabled Onboard Serial Port 2 : COM2/2F8 Video BIOS Cacheable : Disabled Onboard Parallel Port : 378H 8-bit I/O Recovery Time : 1* Onboard Parallel Mode : ECP 16-bit I/O Recovery Tim e : 1* ECP Mode Us e DMA : 3 Memory Hole At 15M-16M : Disa bled Parallel Port EPP Type : EPP1.9 IDE HDD Block Mode : Enabled Serial Port 1 MIDI : Disabled IDE Primary Master PIO : Auto Serial Port 2 MIDI : Disabled IDE Prim ary Slave PIO : Auto IDE Secondary Master PIO : Auto Esc: Quit :Select Item IDE Secondary Slave PIO : Auto F1 : Help PU/PD/+/-:Modify On-Chip Primary PCI IDE : Enabled F5 : Old Values (Shift)F2 :Color On-C hip Secondary PCI IDE : Enabled F6 :Load BIOS Defa ults PCI Slot IDE 2nd Channel : Enabled F7 :Load Setup Defaults

This screen controls the 'green' feature s of this mainboard.

ROM PCI/ISA BIOS (2A59CA29)

CMOS SETUP UTILITY

AWARD SOFTWARE, INC. STANDARD CMOS SETUP PASSWORD SETTING BIOS FEATURES SETUP IDE HDD AUTO DETECTION CHIPSET FEATURES SETUP SAVE & EXIT SETUP POWER MANAGEMENT SETUP EXIT WITHOUT SAVING PCI CONFIGURATION SETUP LOAD BIOS DEFAULTS LOAD SETUP DEFAULTS ESC: Quit :Select Item F10: Save & Exit Setup (Shift) F2 : Change Color

Tim e, Date, Hard Disk Type .....

ROM PCI/ISA BIOS (2A59CA29)

POWER MANAGEMENT SETUP

AWARD SOFTWARE, INC. Power Manag em ent : Disabled IRQ3 (COM 2) : OFF PM Control by APM : Yes IRQ4 (COM 1) : OFF Video Off Method : V/H SYNC IRQ5 (LPT 2) : OFF

+Blank IRQ6 (Floppy Disk) : OFF

IRQ7 (LPT 1) : OFF Doze Mode : Dis abled IRQ8 (RTC Alarm) : OFF Stan dby Mode : Disabled IRQ9 (IRQ2 Red ir) : OFF Suspend Mode : Disabl ed IRQ10 (Rese rved) : OFF HDD Power Down : Dis abled IRQ11 (Reserved) : OFF

IRQ12 (PS/2 Mous e) : OFF IRQ3 (Wake-Up Event) : On IRQ13 (Coproces s or) : OFF IRQ4 (Wake-Up Event) : On IRQ14 (Hard Di sk) : OFF IRQ8 (Wake-Up Event) : On IRQ15 (Reserved) IRQ12(Wake-Up Event) : On

Esc: Quit :Select Item Power Down Activities F1 : Help PU/PD/+/- : Modify COM Ports Accessed : On F5 : Old Values (Shift) F2: Color LPT Ports Acces sed : On F6 : Load BIOS Defaults Drive Ports Acces sed : On F7 : Load Setup Defaul ts

This screen configures the PCI Bus slots.

ROM PCI/ISA BIOS (2A59CA29)

CMOS SETUP UTILITY

AWARD SOFTWARE, INC. STANDARD CMOS SETUP PASSWORD SETTING BIOS FEATURES SETUP IDE HDD AUTO DETECTION CHIPSET FEATURES SETUP SAVE & EXIT SETUP POWER MANAGEMENT SETUP EXIT WITHOUT SAVING PCI CONFIGURATION SETUP LOAD BIOS DEFAULTS LOAD SETUP DEFAULTS ESC: Quit :Select Item F10: Save & Exit Setup (Shift) F2 : Change Color

Tim e, Date, Hard Disk Type .....

ROM PCI/ISA BIOS (2A59CA29)

PCI CONFIGURATION SETUP

AWARD SOFTWARE, INC. PnP BIOS Auto-Config : Disabled Slot 1 Usi ng INT# : AUTO Slot 2 Usi ng INT# : AUTO Slot 3 Usi ng INT# : AUTO Slot 4 Usi ng INT# : AUTO

1st Available IRQ : 10 2nd Available IRQ : 11 3rd Available IRQ : 9 4th Available IRQ : 12 PCI IRQ Actived By : Level PCI IDE IRQ Map To : PCI-AUTO Primary IDE INT# : A Esc: Quit :Select Item Secondary IDE INT# : B F1 : Help PU /PD/+/- : Modify

F5 : Old Values (Shift) F2: Color F6 : Load BIOS Defaults F7 : Load Setup Defau lts

The last step is 'save and exit'. If you selec t this item and press 'Y', then these records will be saved in the CMOS memory on the mainboard. It will be checked every time when you turn your computer on.

ROM PCI/ISA BIOS(2A59CA29)

CMOS SETUP UTILITY

AWARD SOFTWARE, INC. STANDARD CMOS SETUP PASSWORD SETTING BIOS FEATURES SETUP IDE HDD AUTO DETECTION CHIPSET FEATURES SETUP SAVE & EXIT SETUP POWER MANAGEMENT SETUP EXIT WITHOUT SAVING PCI CONFIGURATION SETUP LOAD BIOS DEFAULTS LOAD SETUP DEFAULTS ESC: Quit :Select Item F10: Save & Exit Setup (Shift) F2 : Change Color

Tim e, Date, Hard Disk Type .....

ROM PCI/ISA BIOS (2A59CA29)

CMOS SETUP UTILITY

AWARD SOFTWARE, INC. STANDARD CMOS SETUP PASSWORD SETTING BIOS FEATURES SETUP IDE HDD AUTO DETECTION CHIPSET FEATURES SETUP SAVE & EXIT SETUP POWER MANAGEMENT SETUP EXIT WITHOUT SAVING PCI CONFIGURATION SETUP SAVE to CMOS and EXIT (Y/N):Y LOAD BIOS DEFAULTS LOAD SETUP DEFAULTS ESC: Quit :Select Item F10: Save & Exit Setup (Shift) F2 : Change Color

Tim e, Date, Hard Disk Type .....

¡/ Control Key Description ¡/

UP ARROW DOWN ARROW LEFT ARROW RIGHT ARROW

¡ô ¡õ ¡ö ¡÷

Move to previous item Move to next item Move to the item in the left hand Move to the item in the right hand

Esc KEY Esc Main Menu : Quit and not save

changes Setup menu : Exit current page and return to main menu

PgUp KEY Increase the numeric value or

make changes

PgDn KEY Decrease the numeric value or

make changes

F1 KEY Help General help F2 KEY ¡ÕShift¡Ö+F2Change color from total 16 colors

F5 KEY Old Value Restore the pervious CMOS

value from CMOS

F6 KEY Load BIOS

default

F7 KEY Load setup

default

F10 KEY Save & Exit

Setup

Load the default CMOS value from BIOS default table Load Setup default

Save all the CMOS changes and Exit setup, only for Main Menu

APPENDIX A

¡/ ¡/ TECHNICAL SUPPORT REQUEST FORM¡/ ¡/

If the mainboard doesn't function properly, please complete the following informationand return it to your system dealer. If the further information is needed, pleas e attach this s eparatin g s heets .

Model No : ATC-1535 Date of Purchase : ______________

Serial No : ___________________

HARDW ARE :

BRAND MODEL SPEED Q'TY CPU Co-processor SIM Module Asyn.Cache TAG SRAM Sync. Cache

Chipset Brand :__________ Model :__________ Cache Memory :________KB SIMM :___ ____MB (__ EDO Suppo rt) Bus Interface : PCI x ______ , ISA x ______ Hard Disk Interface Controller : __ __ IDE, ____ SCSI Hard Disk Brand :___________, Model :_________, Capacity :________ Display Controller Brand :_____________,Model :__________

Controller Chip Brand :_____________,Model :__________

SO FTW ARE:

SYSTEM BIOS:____ <A>AMI, <W>AWARD Version _________ Date Code _____________ Keyboard BIOS: Brand __________

Other Add-on Cards Informa tion:

Add-on Card Bus Interface Model Remark

Error Description :

A-Trend ATC-1535 ATC-1535 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual