Page 1
FUNCTION SETTINGS
1. To change & set BAUD Rating, Parity & Print Mode
Press [ON/OFF] to turn on the scale on. This display will show --------. As soon as
you see --------, press [PRINT] and the display will show b xxx BAU value (BAUD
Rate). Press [UNIT] to select 1200, 2400, 4800 or 9600.
Press [ZERO] to enter Parity mode, the display will show P XXX PAR. Press [UNIT]
to select odd, even or none (odd stands for 7 data bits with odd parity, even stands
for 7 data bits with even parity, none stands for 7 data bits without parity).
Press [ZERO] to enter Print mode. The display will show n xxx Mod. Press [UNIT]
to select ON, OFF, KEY or STB (OFF stands for serial data output disabled, KEY
stands for demand mode by pressing [PRINT], STB stands for automatic print when
scale is stable and ON stands for continuous print. Press [ZERO] again to return to
weighing mode.
2. To activate and deactivate weighing units
Press [ON/OFF] to turn on the scale on. The display will show digits and then
--------. As soon as you see -------- press [UNIT] to enter unit selection mode. The
display will show ON X (X stands for the units i.e. g or oz). Press [ZERO] to select
an unit and press [UNIT] to select ON (to activate the selected unit) or OFF (to
de-activate the selected unit). Press [ZERO] until you return to weighing mode.
2. To change & set the Zero, Tare, Overload & Back Light settings
Press [ON/OFF] to turn on the scale on. The display will show digits and then
--------. As soon as you see -------- press [PCS]. Following the table below, use the
[ZERO] button to enter each setting and [UNIT] button to change the value in each
setting.
Setting (shown as it is
seen on the display)
What setting you are
changing
What you can choose
from
ZRD X.X
Zero Track Value
0.0, 0.2, 0.4, 0.6,
0.8, 1.0,
1.5 & 2.0
ZRT X.X
Zero Track Time
0.5, 1.0, 1.5, 2.0, 2.5, 3.0,
3.5 & 4.0
RZD X.X
Zero Value
0.8, 1.8, 2.8 & 3.8
FIL X Filter Range
0, 1, 2, 3, 4, 5, 6 & 7
PZR XX
Set percentage for zero
range when the scale is
first turned on
1, 2, 3, 4, 5,
8, 10 & 20
TZR XX
Set percentage of zero
range
3, 4, 5 & 10
TTR XXX
Set percentage of tare
range
50 or 100
OUR XX
Overload Protection
Mode
2, 5, 10 9d
b2 XX
Activate or deactivate
beep when buttons are
pressed
ON or OFF
ZT XX
Unite tare & zero funct
ion ON or OFF
A XXX
Auto-power off settings
3, 5, 10mins or OFF
L XXX
Back Light settings
AUTO, OFF or ON
COMPACT SCALE/BALANCE
INSTRUCTION MANUAL
Page 2
SAFETY PRECAUTIONS
All safety messages are identified by the following the words "WARNING" and
"CAUTION". These words mean the following:
△WARNING
Important information to alert you to a situation
that might cause serious injury and damage to
your scale if instructions are not followed.
△CAUTION
Important information that tells
how to prevent
damage to equipment.
When using the scale/balance, the following safety precautions should always be
followed.
△ WARNING
Use only the AC/DC mains adapter provided with the scale/balance. Other
adapters may cause damage to the scale.
Do NOT use the mains adapter while batteries are fitted inside this scale. It
will result in permanent damage to the circuit board.
△ CAUTION
Avoid installing the scale/balance in direct sunlight; this may cause discoloration or
malfunctions.
Avoid overloading the scale; it could cause damage to the scale/balance.
Do not allow the scale to come into contact with water; it is not water-proof. If
water comes in contact with the circuit board it will damage the scale/balance.
Avoid using the scale near anything that has electrically charged matter. Discharge
the static electricity using an electrification prevention spray and spray on both
sides of the weighing platform.
1
SPECIFICATIONS
Model number Capacity Division
FHB -600 600g 0.01g/0.005g
FHB -3000 3000g 0.05g/0.1g
FHB -6000 6000g 0.1g/0.2g
Platter 120 x 135mm or 160 x 195mm
Net/gross weight 1.8Kg
Package
Standard carton: 36.5x26x16(cm3)
Operating Temperature
0-40℃(32-104℉)
Power source
AC/DC Adapter or Batteries
Adapter 10V/500mA
Parts Counting procedure
1. Press [ON/OFF] to turn on the scale.
Wait for "0" to appear on the display.
2. Start the Count Procedure
If necessary, press the [ZERO] key to set the display to “0”.
3. Press the [PCS] key to put the scale in parts counting mode, the display will
show P=X X, press UNIT to select XX value (10, 20 ,50, 100) and place your
sample on the platform of the scale/balance.
4. Press the [PCS] key, the display will show “XX pcs”, then the scale will recall
the sample size you selected and show the starting sample size on the display.
5. You can now remove the samples if you want to return the scale to 0 & start
counting.
6. Press the [PCS] key to return to the weighing mode
Page 3
6
CALIBRATION
When to calibrate
Calibration may be required when it is initially installed or if the scale/balance is
moved to a substantial distance. This is necessary because the weight of a mass in
one location is not necessarily the same in another location due to gravity. Also,
with time and use, mechanical deviations may occur.
How to calibrate
1. Before entering calibration mode, there is a switch key on the bottom of the
scale. Turn on the switch key first then press [ON/OFF] button on the front of the
scale/balance to turn the power on and leave the scale/balance to warm up for 1
minute.
2. Enter calibration mode
Press [ON/OFF] button to turn the power on. The display will show different digits
and then “--------”. As soon as you see “--------” press [ZERO] twice, the display
will show “CAL.” Press [ZERO] again, the display will show “X0000 CAL”; X
indicates the digit flashing on the display. Press [UNIT] key the flashing digit will
move to the right. Press [PCS] key to increase the flashing digit. (X is the
calibration weight which can be set according to your requirements).
3. Calibration by the weight
When you have entered the weight you wish to carry out the calibration with, place
the calibration weight/s onto the platform of the scale/balance. Then press [ZERO]
key, the display returns to the weighting mode. Remove the calibration weight and
calibration is now complete.
4. Check the calibration has worked
Press [ON/OFF] to turn the scale/balance off. Then press [ON/OFF] to turn the
scale/balance back on. Place the weight on the platform and check that the
scale/balance is weighing correctly, if not, repeat steps 2-4.
5
PARTS DESCRIPTION
BACK
AC adaptor
Socket
FRONT
·Key pad function
1. ON/OFF key: Turn the power on or off.
2. ZERO key: For zero setting of the scale up to 4% of the scales capacity (i.e.
for a 600g capacity 4% would be 24g)
3. TARE key: Press this button to deduct the weight on the display (useful for
containers)
4. PRINT key: To print the displayed data.
5. UNIT key: Press this button to select different weighing units.
6. PCS key: For parts counting function.
DISPLAY
Low battery indicator weighing unit TARE indicator
Negative value indicator
STABLE indicator
Indicates when the
reading is stable.
ZERO indicator
Page 4
2
PREPARATION
1. Installing batteries
Batteries
Battery
compartment switch power
6 AA Batteries
2. Setting up the scale/balance
△! CAUTION
Avoid installing the scale/balance in direct sunlight it may cause discoloration or
malfunctions. Place your scale/balance on a firm weighing table so that the
scale/balance is level. (The scale/balance will not perform accurately when it is not
level.)
Place the scale/balance on a firm surface that is flat and level for an accurate
reading.
3
WEIGHING
Before weighing
Turn the scale on and leave for 10 minutes to warm up before use
Error messages
Err-O: Overload
Err-Z： Zero tracks has been exceeded
Err- S: The scale is unstable
: Low battery
Weighing procedures
1. Press [ON/OFF] to turn on the balance.
When the scale/balance is turned on, all display segments appear on the LCD
display for a few seconds and finally "0" will appear on the display.
2. Select the weighing unit with [UNIT].
Press [UNIT] to select a weighing unit, e.g. g, ct, oz or dwt (there are 16 units to
choose from)
3. Start weighing
If you do not use a container for weighing
Check that the display is showing 0. If not, press [ZERO].
Place objects on the weighing platform to weigh.
When the reading becomes stable, the stable indicator is displayed.
If you use a container for weighing
Check that the display is showing 0. If not, press [ZERO].
Place an empty container on the platform.
Wait for the stability indicator to be displayed and press [TARE].
Place the objects to be weighed in the container.
When the reading becomes stable, the stable indicator is displayed.
FEATURES
User calibration ● Auto shut off (selectable)
Auto zero tracking ● Auto backlight (selectable)
Recharge ●g/ct/oz/….. conversion
Large LCD Display ●counting function
Stability indicator
1/120000 & 1/200000 division available
4
Loading...