Atop Technology EHG6308 User Manual

Download

Page 1

Techn o lo g ie s

Atop Technologies, Inc.

Industrial DIN-Rail Unmanaged PoE Ethernet Switch

EHG6308 series

8-Port Unmanaged PoE Ethernet Switch

with Gigabit Unlink Ports

Hardware Installation Guide

Version 1.0

Updated on Nov. 9, 2011

Tel: 886-3-5508137

Fax: 886-3-5508131

www.atop.com.tw

Introduction

Thank you for choosing the ATOP Industrial DIN-Rail Unmanaged

PoE Ethernet Switch. The Switch delivers non-blocking, wire speed

switching for your 10/100 and network clients and 1000Mbps for

uplink, so all workstations will perform at their maximum speeds.

The guide covers two product models:

■

EHG6308-4PoE:

8-Port Unmanaged PoE Ethernet Switch with Gigabit Unlinks.

Includes 8-Port 10/100/1000Mbps with 4-Port 802.3at Power

over Ethernet Switch

■

EHG6308-4PoE-4SFP:

8-Port Unmanaged PoE Ethernet Switch with Gigabit Unlinks.

Includes 4-Port 10/100/1000Mbps with 802.3at Power over

Ethernet Switch and 4-Port 1000Mbps SFP Fiber.

Use the instructions in this Hardware Installation Guide to help

you install the Switch. These instructions should be all you need

to get the most out of the Industrial Harsh Ethernet Switch.

Inside the Package

■

Main Product

■

Atop EHG6308 Industrial Unmanaged PoE Ethernet Switch x 1

■

Standard Accessories:

■

7-pin Terminal Block ( 2ESDV-07P) x 1

Atop P/N: 50706491G

■

RJ-45 Port Plugs x 4

Atop P/N: 3990012G

■

Hardware Installation Guide(Warranty card is included) x 1

Atop P/N: 89900407G

■

Optional Accessories

■

Wall mount kit x 1

Atop P/N: 202EH731000003G

■

7-pin Terminal Block (2ESDP-07P) x 1

Atop P/N: 50706551G

■

Grounding cable x 1

Atop P/N: 59906861G

Product Description

1 2 3 5

EHG6308 -4P oE

PWR2

Fault

PWR1

PoE

LAN

1 2 3 5

PWR2

Fault

PWR1

PoE

LAN

1. Green: Power input PWR1 LED

2. Green: Power input PWR2 LED

3. Red: Fault LED

4. Yellow: Port 1~4 LED, PoE Port

5. Green: Port 1~8 LED, LAN Port

6. Port 1 ~ 4:

4 ports of 10/100/1000baseT(X) with

RJ-45 connector and PoE function

7. Port 5~8: 10/100/1000BaseT(X) port

EHG6308 -4P oE- 4SF P

1. Green: Power input PWR1 LED

2. Green: Power input PWR2 LED

3. Red: Fault LED

4. Yellow: Port 1~4 LED, PoE Port

5. Green: Port 1~8 LED,

Switch is sending or receiving data

6. Port 1 ~ 4:

4 ports of 10/100/1000baseT(X) with

RJ-45 connector and PoE function

7. Port 5~8: 1000BaseSFP slot

Hardware Installation

■

Electrical

Step 1: Unpack the Switch, check to make sure no external damages and no parts are missing. Step 2: Connect the power adapter/supply (48V~57VDC). It is normal to see the PWR1 and PWR2 indicator on. If the Switch misses one of PWR1 or PWR2, the Fault indicator will on. Step 3: Hook up one RJ-45 port to your LAN, and another port to your computer. Check to make sure your host computer can access the LAN.

Metal Spring

■

Mechanical

All Ethernet Switches are equipped with DIN-Rail bracket attached onto rear panel. Follow the steps below to fasten the switch to DIN-Rail.

Step 1: Tilt the unit slightly backwards. Step 2: Fit the unit over top the DIN-Rail. Step 3: Push downwards and against the DIN-Rail for locking. Step 4: Check that the unit is locked into position.

LED Indicators

There are five LED indicators located at the front panel of EH series.

Name

Fault

PW1/PW2

RJ-45

LED

RED

Green

Yellow

Status

Off

Power input status is normal

Power input is disconnected or failed

Off

No power input detected from PWR1/PWR2

Power is supplied from PWR1/PWR2

Off

Link is down or no cable is plugged in

Blink

Data is transmitting on this port

Link is down or no Powered Device (PD)

Off

is connected

EHG6308 is supplying power to the

connected PD

Description

Page 2

Configuration and Setting Methods

Any settings or configuration is unnecessary.

Pin Assignment of Network Connections

10/100/1000Base-T(X) Ethernet Port Connection

Rx + DC -

TxRx C+

1 8

Rx DC -

TxRx

B -

C -

DC -

UTP 100 m (328 ft)

2km

30 km

TxRxD+TxRx

D -

RJ-45

SFP

RJ-45

10/100Base –T(X)

Signal

1 2 3 4 5 6 7 8

Tx +

Tx -

DC+

1000base-T(X)

Signal

1 2 3 4 5 6 7 8

TxRx

TxRx A DC+

TxRx B+ DC -

A+ DC+

Cable type, Max. Transmission and Connector

Speed Cable Max. Length Connector

10Base-T

100Base-T

1000Base-T

1000Base-SX\SX+

1000Base-LX\LHX\XD

Cat. 3, 4, 5

Cat. 5 UTP

Cat. 5/Cat.5e UTP

Multi-mode

Single-mode

1000Base- Fiber SFP Port Connection

Fiber Port

Single-mode & Multi-mode

Note: The above picture shows the optional accessories available upon request.

7-pin Terminal Block for Power Input

1. Grounding screw

2. Frame Ground

3. Terminal block for power input PWR1

4. Relay output warning for power failure and break alarm. Normally Closed.(1A@24VDC)

5. Terminal block for power input PWR2

1 2 3 4 5

EHG6308 series Physical appearance and Dimensions

(unit=mm)

Front View

EHG6308-4PoE

46,20

PWR2

PWR1

Fault

PoE

LAN

141,25

Real View Panel Mountinrg View

12,50

38,60

17,95

32,60

38,60

19,30

45,90

Redundant inputs Power Supply (48V~57V VDC)

Front View

EHG6308-4PoE-SFP

PWR2

PWR1

Fault

PoE

LAN

4,00

138,20

6,00

DIN-Rail Mount

Top View

Side View

145,70

117,85

PWR1 or PWR2 Failure to Tigger Fault (Normally Closed) (1A@24 VDC)

Warranty Policy

Warranty Conditions

Products supplied by Atop Technologies are covered in this

warranty for sub-standard performance or defective workmanship.

The warranty is not, however, extended to goods damaged in the

following circumstances:

(a) Excessive forces or impacts

(b) War or an Act of God: wind storm, fire, flood, electric shock,

earthquake

procedure

(d) Replacement with unauthorized parts

RMA and Shipping Costs Reimbursement

Customers shall always obtain an authorized "RMA" number from Atop before shipping the goods to be repaired to Atop. When in normal use, a sold product shall be replaced with a new one within 3 months after purchase. The shipping cost from the customer to Atop will be reimbursed by Atop.

After 3 months and still within the warranty period, it is up to Atop whether to replace the unit with a new one; normally, as long as a product is under warranty, all parts and labor are free of charge to the customers.

After the warranty period, the customer shall cover the cost for parts and labor.Three months after purchase, the shipping cost from the customer to Atop will not be reimbursed, but the shipping cost from Atop to the customer will be paid by Atop.

Limited Liability

Atop shall not be held responsible for any consequential losses from using Atop’s product.

Warranty Period

Product Categories

Serial-to-Ethernet Server Serial-to WLAN Server Industrial Wireless Ethernet Device Modbus Gateway Series Industrial Ethernet Switch Embedded Serial Server Pick-to-Light System Auto-Identification and Data Collection-AIDC

※ Warranty coverage for accessories such as power adapters and high-gain antenna is one year.

Warranty

5 Years

1 Year

The warranty certification will not be effective until an authorized stamp issued by Atop’s overseas agents.

Purchase Date: / / (yyyy/mm/dd)

Serial Number:

ATOP Customer Services and Supports

1. Please contact your local dealers or Atop Technical Support Center at the following numbers.

+ 886-3-550-8137 (Atop Taiwan) + 86-21-6495-6232 (Atop China)

2. Please report the defected problems via Atop’s Web site or E-mail account

Web Site：www.atop.com.tw, e-mail：service@atop.com.tw Web Site：www.atop.com.cn, e-mail：service@atop.com.cn

G V1- V1+ V2- V2+

Relay

PWR1

PWR2

─ Any change by website in material announcement primarily. ─