Atop Technology EH2305 User Manual

Download

Page 1

Techn olo gie s

Atop Technologies, Inc.

Industrial DIN-Rail Unmanaged Ethernet Switch

EH2305-1Fm

EH2305-1Fs

EH2306

EH2308

5/6/8-port Industrial Unmanaged Ethernet Switch

Hardware Installation Guide

Version 1.4

Updated on March, 2012

Introduction

Thank you for purchasing Atop EH-series Industrial Ethernet Switch. This document intends to provide customers with brief descriptions about the product and to assist our customers to get started using our devices.

Inside the Package

- Main Product

■

One EH2305-1Fm, EH2305-1Fs, EH2306 or EH2308 device

- Standard Accessories

■

Terminal block for power input

■

The hardcopy of EH-series Hardware Installation Guide

- Optional Accessories

■

US315-12(US), AC100V~240V 50/60HZ 12V/1.25A, US Plug (optional)

→ Atop PN:50500151120009G

■

US315-12(EU), AC100V~240V 50/60HZ 12V/1.25A, EU Plug (optional)

→ Atop PN:50500151120019G

Product Description

EH2305-1Fm

5-Port Unmanaged Fast Ethernet Switch with Multi-mode Optical Fiber

■

4 ports of 10/100Base-TX with RJ-45 connector

■

1 port of 100Base-FX Multi-mode Optical Fiber

with ST connector

Data Link

Fault

F.G.

V-

V+

F.G.

V-

V+

90.6mm

F.G.

V-

V+

F.G.

V-

V+

90.6mm

Data Link

FaultP1

45.4mm

EH2306

6-Port Unmanaged Fast Ethernet Switch

■

6 ports of 10/100Base-TX with RJ-45 connector

P2P2P1

V- V+ V- F.G.

V+

90.6mm

EH2308

90.6mm

P1 P2

Fault

F.G.

V-

V+

F.G.

V-

V+

45.4mm

8-Port Unmanaged Fast Ethernet Switch

■

8 ports of 10/100Base-TX with RJ-45 connector

45.4mm

Hardware Installation

Step1: Installation on “DIN-Rail”

■

All EH23xx Switches are equipped with a DIN-Rail bracket attached onto the rear panel. Please follow the below steps to fasten the switch to the DIN-Rail correctly.

■

Tip the switch forward and press it against the DIN-Rail after align

the bracket springs to the DIN-Rail.

■

Press the bracket against the upper ledge of the DIN-Rail until it

clicks.

Step2: Connecting the Power

■

Prepare the suitable power source and connect it into EH Switch

by Terminal Blocks (TB3/TB5).

■

DC 9-30V for EH2305-1Fm, EH2305-1Fs and EH2306 switch

products.

■

DC 9-48V for EH2308 switch product.

■

You can connect two DC inputs for EH switch power if auto-backup

needed.

■

Check P1/P2 power LED. The LED(s) will be lighted when the

device is ready.

3-pin Terminal Block for Power Input

F.G.

Pin Signal

V-

V+

V+ V- F.G.

DC9-30V 0V Frame Ground

5-pin Terminal Block for Power Input

P2 P1

V+

V- V+ V- F.G.

Pin Signal

V+ V- F.G.

DC9-48V 0V Frame Ground

Warning:

Before connecting EH23xx to the DC power input, please make sure the DC voltage supplied by the power source is correct and stable.

Step3: Connecting the Network Devices

■

Connect your devices using standard UTP/STP cable with RJ-45 connectors to EH switch. (For the cable wiring diagrams, please refer to section 7)

■

The corresponding RJ-45 or Fiber SC/ST LED will be lighted if the Ethernet connection is linked successfully.

■

The LED will be blinked during data transfer by EH switch.

※UL Notice for Power supplier

All the series of EH products are intended to be supplied by a Listed Power Unit marked with “LPS”, “Limited Power Source” or “Class 2” with output rate 9-30VDC 0.6A for EH2305-1Fm, EH2305-1Fs and EH2306; 9-48V 0.35A(max) for EH2308. Or, use the recommended power supplies in “Optional Accessories”.

Tel: 886-3-5508137

Fax: 886-3-5508131

www.atop.com.tw

EH2305-1Fs

5-Port Unmanaged Fast Ethernet Switch

45.4mm

with Single-mode Optical Fiber

■

4 ports of 10/100Base-TX with RJ-45 connector

■

1 port of 100Base-FX Single-mode Optical Fiber

with SC connector

Notice :

The EH23xx series switch is designed to be mounted on a well-grounded place, such as a metal panel.

Page 2

LED Indicators

There are four LED indicators located at the front panel of EH series.

Name

Fault

P1/P2

RJ-45

Fiber

SC/ST

LED

Green

Yellow

Data

Link

Status

Off On Off On Off

Blink

Off On Off

Blink

Off On

Both P1 and P2 on or off Either P1 or P2 on Power input 1/2 is not plugged yet Power status is ready Link is broken, or no cable is plugged in

The device is transferring data through the port

The link is operated at rate of 10 Mbps The link is operated at rate of 100 Mbps No data transfer

The device is transferring data through the port

No media available Working, the media is ready

Description

Configuration and Setting Methods

Any settings or configurations are unnecessary.

Pin Assignment of Network Connections

RJ-45(8-pin) to RJ-45(8-pin) straight-through cable wiring

1 8

Cable

10/100BaseT(X) Ethernet Port Connection

RJ-45

Pin Signal

RJ45(8-pin) to RJ45(8-pin) cross-over cable wiring

10/100BaseT(X) Ethernet Port Connection

RJ-45

1 2 3 4 5 6 7 8

Tx+ T x - R x + Rx-

1 8

100Base-Fx Fiber SC/ST Port Connection

SC Connectors ST Connectors

Fiber Port

100Base-Fx Fiber SC/ST Cable Wiring

ST Connector

TX RX

SC Connector

TX RX

Single-mode Multi-mode

A B

←→ ←→

B A

Warning:

To protect user’s eyes from a serious damage, don’t stare into the Laser Beam.

Mechanical dimensions(unit=mm)

4.5

90.6

103.2

115.2

27.2

RX TX

Warranty Policy

Warranty Conditions

Products supplied by Atop Technologies are covered in this warranty for sub-standard performance or defective workmanship. The warranty is not, however, extended to goods damaged in the following circumstances:

(a) Excessive forces or impacts (b) War or an Act of God: wind storm, fire, flood, electric shock, earthquake (c) Use of unqualified power supply, connectors, or maintenance procedure (d) Replacement with unauthorized parts

RMA and Shipping Costs Reimbursement

Customers shall always obtain an authorized "RMA" number from Atop before shipping the goods to be repaired to Atop. When in normal use, a sold product shall be replaced with a new one within 3 months after purchase. The shipping cost from the customer to Atop will be reimbursed by Atop.

After 3 months and still within the warranty period, it is up to Atop whether to replace the unit with a new one; normally, as long as a product is under warranty, all parts and labor are free of charge to the customers.

After the warranty period, the customer shall cover the cost for parts and labor.Three months after purchase, the shipping cost from the customer to Atop will not be reimbursed, but the shipping cost from Atop to the customer will be paid by Atop.

Limited Liability

Atop shall not be held responsible for any consequential losses from using Atop’s product.

Warranty Period

Product Categories

Ethernet Switches Wireless Serial Device Servers Modbus Gateways

90.6

Embedded Device Servers DIN-Rail Power Supplies Power Adaptors Antennas Other Accessories

Warranty

5 Years

3 Years

1 Year

The warranty certification will not be effective until an authorized stamp issued by Atop’s overseas agents.

Purchase Date: / / (yyyy/mm/dd)

Serial Number:

ATOP Customer Services and Supports

1. Please contact your local dealers or Atop Technical Support Center at the following numbers.

+ 886-3-550-8137 (Atop Taiwan) + 86-21-6495-6232 (Atop China)

2. Please report the defected problems via Atop’s Web site or E-mail account

Web Site：www.atop.com.tw, e-mail：service@atop.com.tw Web Site：www.atop.com.cn, e-mail：service@atop.com.cn

Pin Signal

1 2 3 4 5 6 7 8

Rx+ R x - T x + Tx -

32.2

45.4

78.7

90.3

─ Any change by website in material announcement primarily. ─

Housing side view(Mount kit)Backboard rear view