Page 1
AMERICAN
TECHNOLOGIES
NETWORK
CORP.
u s e r ` s g u i d e
Ultra Sight
Digital Ultra Sight
Page 2
The information in this manual furnished for information use only, is subject to change without notice, is not
to be construed as a commitment by ATN Corp.
ATN Corp. assumes no responsibility or liability for any errors or inaccuracies that may appear in this book.
©2002 ATN Corp. All right reserved.
FOUR RE TIC LE PAT TE RNS
Circle with dot
1 MOA
60 MOA
60 MOA
Cross Hair
2 MOA
Dot
25 MOA
50 MOA
60 MOA
6 MOA
Open Cross Hair
with Dot
ULTRA SIGHT SPECIFICATIONS
• Magnification: 1
• Exit Pupil: 32mm
• Windage & Elevation: 1click=1/2” at 100 yards
• Multi (4) Reticle System
• Maximum movement after change reticle is 2MOA
• Parallax Free
• 3V lithium battery (CR2032)
• Dimensions: 130x45x72 mm
• Weight: 0.2kg (0.45lb)
Large 33 mm
Heads Up
Display
Reticle Pattern
Selector
Elevation
Windage
Standard Weaver
Mount
Battery Housing
6 MOA
50 MOA
11 Position
Brightness
Control
ULTRA SIGHT
Page 3
2
ULTRA SIGHT FEATURES
• 4 reticle patterns to choose from.
• 11-position rheostat for
reticle pattern brightness
adjustment.
• Instant Target acquisition.
• Fits standard Weaver style base.
• ldeal for handguns, rifles and shot
-
guns.
• Heads up display for extra wide field
of view.
• Installs quickly using 2 thumbnut
tightened clamps for extra stability.
• High intensity diode for super bright
reticle pattern.
• Efficient electrical design for long
battery life.
ABOUT ULTRA SIGHT
The Ultra Sight by ATN is designed to
be a both eyes open, heads-up, rapid
acquisition red dot sight. A revolution
ary design lets you choose between
four reticle patterns with a simple twist
of a knob. A 11-position adjustment
for brightness and an accurate wind
age Ultra Sight one of the best Red
Dot sights on the market.
OPERATING INSTRUCTION
Insert Battery:
The battery (included) is a coin style
3volt lithium (model #2032).
Unscrew the battery cap that is
located on the top of the 11-position
brightness control rheostat.
The battery goes in negative side
first.
Turning the Ultra Sight on:
After the battery is inserted turn the
11-position brightness control rheo
-
stat from 0 (off) to the desired bright
ness 1 through 11. Hold the Ultra sight
away from you and look through it with
both eyes open to see a reticle pat
tern.
Reticle Patterns:
Every Ultra Sight comes with four reticle patterns.
• Cross hair
• Dot
• Circle with dot
• Open cross hair with dot
You can choose your preferred pat
tern by turning the Reticle Pattern
adjustment knob.
Page 4
3
4
DIGITAL ULTRA SIGHT SPECIFICATIONS
• Magnification: 1
• Exit Pupil: 32 mm
• Windage & Elevation: 1 click=1/2" at 100 yards
• Multi-Reticle System
• Parallax Free
• 3V lithium battery (CR2032)
• Dimensions: 130x45x72 mm
• Weight: 0 2kg (0.45lb)
Large 33 mm
Heads Up
Display
Reticle Pattern
Selector
Power Button
Elevation
Windage
Digital
Brightness
Control
Standard Weaver
Mount
Battery Housing
FIVE R E TICLE PAT TE RNS
1 MOA
60 MOA
60 MOA
Open Cross Hair
2 MOA
Dot
1 MOA
60 MOA
Post
6 MOA
60 MOA
1 MOA
Post with Dot
60 MOA
1 MOA
60 MOA
6 MOA
Cross Hair
DIGITAL ULTRA SIGHT
Page 5
4
DIGITAL ULTRA SIGHT
FEATURES
• Patented technology keeps point
of impact from shifting when you
change reticles.
• 5 reticle patterns to choose from.
Pattern can be changed with a push
of a button.
• Digital push controls to adjust reticle
pattern brightness.
• Parallax Free.
• Brightness level memory.
• Reticle pattern memory.
• Instant Target acquisition.
• Fits standard Weaver style base.
• Ideal for handguns, rifles and shot
-
guns.
• Heads up display for extra wide field
of view.
• Installs quickly using 2 thumbnut
tightened clamps for extra stability.
• High intensity diode for super bright
reticle pattern.
• Efficient electrical design for long
battery life.
• Low battery indication.
• Optional Bright Light Filter available
for optimum performance in super
bright conditions.
ABOUT DIGITAL ULTRA SIGHT
The Digital Ultra Sight by ATNc is
designed to be a both eyes open,
heads-up, rapid acquisition reflex
sight with a New revolutionary feature
called MultiAim®.
MultiAim® makes the ATNc Digital
Ultra Sight the only sight on the
market where user can instantly
change the reticle pattern of the sight
with pushing a button, without a shift
in the point of impact.
Digitally controlled MultiAim® allows
an array of features such as 5-reticle
configurations, reticle brightness
adjustments, brightness level
memory, reticle pattern memory and
low battery indication.
Since there are no movable parts
the reliability of the device is greater
then standard reflex sights. MultiAim®
combined with superb optics, rugged
construction, highly accurate windage
and elevation system and an efficient
electrical design for long battery life
makes the Digital Ultra Sight the best
Reflex sight on the market.
Military Personnel, Law Enforcement
Professionals, Hunters and Sport
Marksmen can enjoy the sight that sur
passes the competition in features and
is priced far more economically.
OPERATING INSTRUCTION
Insert Battery
The battery (included) is a coin style
3Volt lithium (model #2032).
Unscrew the battery cap that is
located on the rear side of the unit.
The battery goes in negative side first.
Page 6
5
6
Turning the Digital Ultra Sight on
After the battery is inserted press
Power button to turn unit on. Adjust
reticle pattern with a push of the
Digital Brightness Control buttons to
the desired brightness. Hold the Ultra
sight away from you and look through
it with both eyes open to see a reticle
pattern.
Reticle Patterns
Every Digital Ultra Sight comes with
five reticle patterns.
• Dot
• Post
• Post with Dot
• Open Cross Hair
• Cross Hair
You can choose your preferred pattern by pushing the Reticle Pattern
Selector button.
MOUNTING
The Ultra Sight and Digital Ultra
Sight are designed to be mounted on
a standard 7/8 weaver rail.
CAUTION: Be sure gun is not loaded. Use safe
gun handling procedures at all times.
Slightly loosen horizontal fixation
screws. Place the scope on the
dovetail mount, making certain that
the mount aligns with the receptor
attachment screw. Re-tighten hori
-
zontal fixation screws.
WINDAGE AND ELEVATION
ADJUSTMENTS
The vertical (elevation) and horizontal (windage) adjustments for the
Ultra Sight and Digital Ultra Sight can
be achieved by turning the windage
and elevation adjustment mecha
nisms. Each click equals 1/2 inch at
100 yards. When reaching the maxi
-
mum of the rotation do not use force.
MAINTAINING YOUR
ULTRA SIGHT
The Ultra Sight and Digital Ultra
Sight are waterproof and shockproof. However, you should never try
to take apart or clean it infernally
(it will void your warranty). If your
scope ever does need repairs or
adjustments, it should be returned
to ATN's service department. The
exposed optical surfaces will perform
their best if they are occasionally
wiped clean with a lens cloth or with
optical quality lens paper like those
for eyeglasses or camera lenses.
Maintain the metal surfaces of you
ultra sight by removing any dirt or
sand with a soft brush so as to avoid
scratching the finish. Wipe down the
scope with a damp cloth and follow
with a dry cloth. Finally, going over
the body with a silicon treated cloth
will restore luster and protect the
scope against corrosion, be careful
not to touch any of the lenses with the
silicon cloth.
Page 7
6
2 YEAR PRODUCT
WARRANTY
This product is guaranteed to be free from
manufacturing defects in material and workmanship under normal use for a period of 2
(two) years from the date of purchase. In the
event a defect that is covered by the foregoing
warranty occurs during the applicable period
stated above, ATN, at its option, will either
repair or replace the product, and such action
on the part of ATN shall be the full extent of
ATN’s liability, and the Customer’s sole and
exclusive remedy. This warranty does not cover
a product (a) used in other than its normal and
customary manner; (b) subjected to misuse;
(c) subjected to alterations, modifications or
repairs by the Customer of by any party other
than ATN without prior written consent of ATN;
(d) special order or “close-out” merchandise or
merchandise sold “as-is” by either ATN or the
ATN dealer; or (e) merchandise that has been
discontinued by the manufacturer and either
parts or replacement units are not available
due to reasons beyond the control of ATN.
ATN shall not be responsible for any defects or
damage that in ATN’s opinion is a result from
the mishandling, abuse, misuse, improper
storage or improper operation, including use in
conjunction with equipment which is electrically
or mechanically incompatible with or of inferior
quality to the product, as well as failure to maintain the environmental conditions specified by
the manufacturer. This warranty is extended
only to the original purchaser. Any breach of
this warranty shall be waived unless the customer notifies ATN at the address noted below
within the applicable warranty period.
The customer understands and agrees that
except for the foregoing warranty, no other
warranties written or oral, statutory, expressed
or implied, including any implied warranty of
merchantability or fitness for a particular pur
pose, shall apply to the product. All such
implied warranties are hereby and expressly
disclaimed.
Limitation of liability
ATN will not be liable for any claims, actions,
suits, proceedings, costs, expenses, damages or liabilities arising out of the use of this
product. Operation and use of the product
are the sole responsibility of the Customer.
ATN’s sole undertaking is limited to providing
the products and services outlined herein in
accordance with the terms and conditions of
this Agreement. The provision of products
sold and services performed by ATN to the
Customer shall not be interpreted, construed,
or regarded, either expressly or implied, as
being for the benefit of or creating any obligation toward any third party of legal entity
outside ATN and the Customer; ATN’s obligations under this Agreement extend solely to
the Customer. ATN’s liability hereunder for
damages, regardless of the form or action,
shall not exceed the fees or other charges
paid to ATN by the customer or customer’s
dealer. ATN shall not, in any event, be
liable for special, indirect, incidental, or
consequential damages, including, but
not limited to, lost income, lost revenue,
or lost profit, whether such damages were
foreseeable or not at the time of purchase,
and whether or not such damages arise
out of a breach of warranty, a breach of
agreement, negligence, strict liability or
any other theory of liability.
Product warranty registration
In order to validate the warranty on your product, ATN must receive a completed Product Warranty Registration Card for each unit. Please
complete the form below and immediately mail
it to our Service Center: ATN Corporation, 20
South Linden Ave., Suite 1B, South San Francisco CA 94080. Products qualifying for warranty repair will be either repaired or replaced
within 10 business days of receipt of merchandise unless the customer is notified otherwise.
Obtaining warranty service
To obtain warranty service on your unit, take or
send the product, postage paid, with a copy of
your sales receipt to our service center, ATN
Corporation at the address noted above. All
merchandise must be fully insured with the correct postage; ATN will not be responsible for
improper postage, or, missing or damaged merchandise during shipment.
Page 8
For customer service and technical support, please contact
American Technologies Network Corp.
North American Office
20 S. Linden Ave. Suite 1B, South San Francisco, CA 94080
phone: 800-910-2862, 650-875-0130; fax: 650-875-0129
European Office
phone: 44(0)870-0111286, fax: 44(0) 870-121-3590
The following countries can use our
toll free number 00 800 9102-8620
Austria, France, Germany, Holland, Italy, Spain, Sweden, Switzerland
www.atncorp.com
Loading...