ATN ThOR-HD 384 9 - 36x, ThOR-HD 640 1.5 - 15x, ThOR-HD 384 1.25 - 5x, ThOR-HD 384 4.5 - 18x, ThOR-HD 640 2.5 - 25x User Manual
...
ThOR-HD Series
THERMAL SMART HD RIFLESCOPE
MANUAL
THOR-HD USER’S GUIDE (REV. 4, AUGUST, 2017)
AMERICAN
TECHNOLOGIES
NETWORK
CORP.
2
THIS PRODUCT CONTAINS NATURAL RUBBER LATEX, WHICH MAY CAUSE ALLERGIC REACTIONS
CAUTION!
The instructions in this manual are for informational use only and subject to change without notice,
this manual is not to be construed as a commitment by ATN Corp.
ATN Corp. assumes no responsibility or liability for any errors or inaccuracies that may appear in this book.
©2017 ATN Corp. All rights reserved.
PICATINNY RAIL
DIOPTER
ADJUSTMENT RING
MOUNTING SYSTEM
POWER BUTTON
FOCUS
ADJUSTMENT RING
BATTERY
HOUSING CAP
START/STOP
VIDEO RECORDING
ENTER BUTTON
TAKE A PICTURE
ZOOM IN
ZOOM OUT
MICROSD,
MICRO HDMI
& MICRO USB
3
TABLE OF CONTENTS
FEATURES ....................................4
APPLICATION .................................4
SPECIFICATIONS ..............................5
PREPARING THE DEVICE .......................7
Unpacking .................................7
Installation of batteries ........................7
MicroSD, USB and HDMI ports .................7
Firmware update ............................8
ON/OFF ...................................9
Using keypad ...............................9
Focusing ..................................9
Mounting your scope ........................10
Compass calibration ........................10
INTERFACE ..................................11
Homescreen ..............................11
Main operations ............................12
Shortcut carousel ..........................13
Using System Settings .......................14
FUNCTIONS ..................................16
Photo modes ..............................16
Recoil Activated video .......................17
Rangefinder ...............................19
Zeroing ..................................21
Ballistic Calculator ..........................22
How to perform a NUC .......................26
Pixel Correction Procedure ...................26
Reticle style adjustment ......................27
SYSTEM SETTINGS .......................... 28
Thermal ..................................28
Photo/Video ...............................28
Display ...................................29
Profiles/Zero ..............................29
Settings ..................................30
SERVICING ..................................31
Warnings and cautions ......................31
MOBILE APPLICATIONS .......................31
4
FEATURES
RECORD HD VIDEO BALLISTIC CALCULATOR
WiFi OBSIDIAN USER INTERFACE
SMOOTH ZOOM BLUETOOTH
E-COMPASS 3D GYROSCOPE
SMART RANGE FINDER
RECOIL ACTIVATED VIDEO (RAV)
APPLICATION
The most technologically advanced line of thermal rifle scopes on the
market, bar none! The all new Obsidian “T” II Thermal Core is at the heart of
all ATN systems. This technology helped ATN to continue to make bigger and
better updates to its award winning thermal product line.
Record videos and photos onto a microSD card. Never again forget to
record that perfect shot with ATN’s patented RAV (Recoil Activated Video).
Use ATN’s Smart Range Finder to quickly range in on your target and allow
the ballistic calculator to make instantaneous corrections to your POI (Point
of Interest) on the fly. Plus, take advantage of the additional features and
sensors packed into these incredible systems, such as; Smooth Zoom, built
in Wi-Fi, Bluetooth, 3D Gyroscope, 3D Accelerometer and 3D Magnetometer.
5
SPECIFICATIONS
ThOR-HD 384
1.25 - 5x
ThOR-HD 384
2 - 8x
ThOR-HD 384
4.5 - 18x
ThOR-HD 384
9 - 36x
ThOR-HD 640
1 - 10x
ThOR-HD 640
1.5 - 15x
ThOR-HD 640
2.5 - 25x
ThOR-HD 640
5 - 50x
Item #
TIWSTH381A TIWSTH382A TIWSTH384A TIWSTH389A TIWSTH641A TIWSTH642A TIWSTH643A TIWSTH645A
Sensor
384×288 640×480
Magnification
1.25 - 5x 2 – 8× 4.5 – 18× 9 – 36× 1 – 10× 1.5 – 15× 2.5 – 25× 5 – 50×
Angle of view
16×12.5 12×9.5 6×4.7 3×2.4 32×25 24×19 12.5×9.7 6×4.7
Objective lens focal length
19 mm 25 mm 50 mm 100 mm 19 mm 25 mm 50 mm 100 mm
Micro Display
HD Display
Core
ATN Obsidian “T” II
Eye relief
65 mm
Waterproof rating / IP rating
Weather resistant
Video Record Resolution
1280×960 @ 30 fps
Microphone
Yes
MicroSD card
Up to 64 GB
Micro USB
Yes
Micro HDMI
Yes
WiFi (Streaming, Gallery,
& Controls)
iOS & Android
Bluetooth
4.1
GPS (Geotagging, Elevation, etc.)
Yes
6
ThOR-HD 384
1.25 - 5x
ThOR-HD 384
2 - 8x
ThOR-HD 384
4.5 - 18x
ThOR-HD 384
9 - 36x
ThOR-HD 640
1 - 10x
ThOR-HD 640
1.5 - 15x
ThOR-HD 640
2.5 - 25x
ThOR-HD 640
5 - 50x
3D Gyroscope
Yes, GS7
3D Accelerometer
Yes
3D Magnetometer
Yes
Range Finder
Yes
Ballistic Calculator
Yes
RAV (Recoil Activated Video)
Yes
Electronic Compass
Yes
Smooth Zoom
Yes
Reticles
Multiple Patterns & Color Options
Mount
Two fixing
screws mount
Picatinny Quick Release Mount, Interchangeable
Compatible mounts
A.R.M.S.® #17® (single lever), A.R.M.S.® #35® (double lever), LaRue LT270, American Defense (AD-170)
Battery life (Li-ion)
8 hr
Battery type
(4) AA (Lithium Recommended)
Dimensions
6.85”×3.16”×3.14”
174×80.26×80 mm
8.81”× 3 .16”×3.14”
224×80.26×80 mm
10.67”×3.97”×3.47”
271×101×8 8 mm
6.85”×3.16”×3.14”
174×80.26×80 mm
8.81” x 3.16” x 3.14”
224×80.26×80 mm
10.67”×3.97”×3.47”
271×101×8 8 mm
Weight
1.55 lb / 0.68 kg 1.85 lb / 0.84 kg 2.75 lb / 1.24 kg 1.55 lb / 0.68 kg 1.85 lb / 0.84 kg 2.75 lb / 1.24 kg
Warranty
3 years
Human Detection Range
625 800 1500 2500 625 800 1500 2500
Human Recognition Range
280 400 600 1100 280 400 600 1100
Human Identification Range
170 250 360 600 170 250 360 600
* ATN reserves the right to change the above specifications at any time without notice
7
PREPARING THE DEVICE
UNPACKING
The following steps must be performed prior to use:
1. Open packaging box, remove ThOR-HD and check the contents.
• ATN Help Card
• ATN Thor- HD
• Battery Lifetime Information and Power Kit Card
• FB Group and ATN Forum Card
• Firmware Update and Review Card
• Black Nylon Case
• Thor HD Manual
• Thor HD Quick Start Guide Card
2. Make sure that nothing is missing.
3. Inspect the device for damage to optical surfaces, body, eyecups, opera-
tion buttons, etc.
4. Ensure that all optical surfaces are clean and ready for use.
NOTE
If any accessories are missing or broken contact ATN’s Customer Ser-
vice.
INSTALLATION OF BATTERIES
The Thor-HD will operate on four AA-type Lithium batteries.
NOTE
We highly recommend using lithium AA
batteries. They will provide much longer battery life. Use only 1.5 V batteries.
Install batteries as follows:
1. Remove the battery cap by unscrewing it
counter clockwise.
2. Insert batteries as shown.
3. Return the battery cap into the housing
socket (screw clockwise until finger tight). Make
sure that the Red O-Ring is not visible to prevent shut off issues due to recoil, but also Do not over-tighten! You want to
ensure you can unscrew the cap next time you replace batteries.
NOTE
Make sure that the device is turned off before changing source of
energy (batteries or USB in power supply mode).
MicroSD, USB
AND HDMI PORTS
The device is equipped with microSD, micro
USB and micro HDMI ports and can be found
under the cap near the battery block (marked
with appropriate icons on the cap).
NOTE
Make sure the device is turned off before
inserting the microSD card into the slot.
8
To Us e:
1. USB cap cover should be unscrewed
counterclockwise.
2. Format new cards before use.
3. Insert microSD card as shown.
4. To lock, insert card in the slot and
push it with a thin object (a small coin,
paperclip, toothpick, etc.).
5. Return the cap to the USB cap cover
(screw clockwise until finger tight).
NOTE
There is only one correct direction to
insert the microSD Card. Do not force
the card into the slot, as it may damage
both the scope and the card itself.
To remove the microSD Card from the
slot:
1. Push it in using the same thin object.
2. When it pops up a few millimeters, it
can be pulled with your fingers or tweezers.
NOTE
If you are going to record video, the microSD card should be a Class 10 (10
Mb/s) or faster and have capacity from 4 to 64 Gb.
FIRMWARE UPDATE
Before operating your device, update the firmware to the latest version.
To receive a notification of new firmware updates, please register your
device on our website (you’ll receive an email letting you know when the new
firmware becomes available).
To update the new firmware you will need a microSD card and batteries that
are fully charged.
NOTE
In the event of a power failure during an update. The device may crash,
corrupting its system files. It will need to be sent back to the ATN factory for
service. DO NOT USE an additional source of power during firmware update!
Update the new firmware as follows:
1. Download the ***.bin file from
https://www.atncorp.com/firmware (You
may need to create an account, if you
didn’t create it earlier) and copy to your
microSD Card — root directory.
2. Insert the card into the device.
3. Turn ON the device.
4. In the “Firmware Update” dialog
box select “Yes” to start the update.
5. When the update counter rea ches
“100%” the device will automatically restart.
6. Once the device is powered up it will enter self configuration mode.
7. After completing it will automatically restart and will be ready for use.
8. Motion Sensing platform will be configured when first turned on.
9. Once the Firmware update completes, please do a factory reset before using
the product.
10. Please remember to delete the Firmware File off of the microSD card after
all steps are completed.
9
NOTE
If the device does not restart within 30 seconds, remove and re-insert
the batteries, and again power-up the device. Once the device has been
updated you will need to either format the card or delete the update file
manually. In the event you do not perform the previous actions, the system
will ask you if you wish to update the device every time you turn it on.
ON/OFF
To TURN ON the device,
press and hold the POWER
Button until you see the ATN
splash screen.
To TURN OFF the device,
press and hold the POWER
Button until the “Shut down
the device?” appears in the
dialog box. Choose “Yes” to turn off the unit.
NOTE
Upon startup you must perform a NUC. Please refer to page 26 to learn
how to perform the NUC process correctly.
USING KEYPAD
The KEYPAD is programmed to be used
in two different ways:
• Short and Quick Taps — used for most
functions and to get around the menu;
• Press and Hold — designed to be
used in the following situations — ON/
OFF, ZOOM and SHORTCUT MENU.
NOTE
Using LEFT or RIGHT buttons in the
Menu will allow you to quickly choose
Exit Shortcut from any position.
FOCUSING
DIOPTER ADJUSTMENT
Look through the eyepiece, focusing on
the reticle on the screen, and rotate the
Diopter Adjustment Ring until optimal
sharpness is achieved. Do not take the
rubber cap off the objective lens.
NOTE
You should not have to re-adjust the
Diopter Adjustment unless another
user, with different vision needs, uses
the scope.
FOCUS ADJUSTMENT
Remove the cap from the objective lens
and rotate the focus adjustment ring, as
necessary, to achieve the proper focus at
various distances.
DIOPTER
ADJUSTMENT RING
FOCUS
ADJUSTMENT
RING
10
MOUNTING YOUR SCOPE
OPEN
CLOSE
Secure the ThOR-HD to your Picatinny Rail using the Quick Release Mount
as shown above. However, the ThOR-HD 384 1.25-5x has a different mount —
with two fixing screws.
1. Slightly loosen the fixing
screws on the 7/8˝ weaver
mount built into the scope.
2. Place the scope on the
weaver rail of the firearm.
3. Tighten the fixing screws.
NOTE
Fixing screws may need
to be tightened after continuous shooting. ATN recommends using “Loctite”
to ensure screws do not
loosen up during shooting.
COMPASS CALIBRATION
When the compass needs
to be calibrated, the word
“CAL” appears instead of
the Compass Scale. To calibrate, rotate the three axis
points as pictured on the left,
on the device.
NOTE
After calibrating the device, please remember that
the compass will work best
when holding the ThOR-HD
parallel to the ground.
Other possible abbreviations:
• ERR — an error was detected, you may need to restart the device or reca-
librate the compass;
• SMF — your device is under a strong magnetic field, move away from the
source;
• UPD — your firmware needs to be updated.
11
INTERFACE
HOMESCREEN
The Homescreen will first appear when you switch on the device. It consists
of Scales, Status Bar icons and different Information Widgets.
SCALES
• The E-Compass Scale shows yaw angle based on e-Magnetometer data.
• Roll Scale shows the rifles cant based on internal 3D Gyroscope.
• Pitch Scale shows rifle inclination based on internal 3D Gyroscope.
STATUS BAR
Information displayed will only be about the current state of system.
Inactive icons become invisible, only the important information will show at
the moment:
• Battery — appears when energy level is low;
• SD Card — shows the presence of memory card;
• Ballistic Calculator, Bluetooth, GPS and WiFi — shows when a function
is enabled.
WIDGETS
There are interface elements that provide quick access to useful informa-
tion. There are several types of widgets:
• icons without value are used for mode display (Photo and Video Modes).
• only numerical value (Detailed Roll and Pitch Values).
• icons with a numerical value: Zoom, Time, Reticle Correction, Distance,
Video Recording.
• Photo Preview appears in the bottom of the Homescreen, after the photo
was taken.
Loading...