Page 1
ATN 10x42RF
OMEGA CLASS BINOCULAR
USER’S GUIDE (ATN 10X42RF) REVISION 2 - SEPTEMBER 2009
user’s manual
Important Export Restrictions! Commodities,
products, technologies and services contained in
this manual are subject to one or more of the export
control laws and regulations of the U.S. Government
and they fall under the control jurisdiction of either the
US Department of State or the US BIS-Department
of Commerce. It is unlawful and strictly prohibited
to export, or attempt to export or otherwise transfer
or sell any hardware or technical data or furnish
any service to any foreign person, whether abroad
or in the United States, for which a license or written
approval of the U.S. Government is required, without
first obtaining the required license or written approval
from the Department of the U.S. Government having
jurisdiction. Diversion contrary to U.S. law is prohibited.
Page 2
Cap of threaded hole for tripod adapter
Lenses
Diopter
adjustment
Neck strap loops
Rubber lens cap
Durable rubber armor body
ATTENTION!
neVer looK aT The sun!
iT may cause loss oF sighT.
CAUTION:
Thi s producT conTains naTural rubber
laTe x wh i ch may cause allerg i c re acTion s.
The information in this manual furnished for information use only, is subject to
change without notice, is not to be construed as a commitment by ATN Corp.
ATN Corp. assumes no responsibility or liability for any errors or inaccuracies
that may appear in this book.
© 2009 ATN Corp. All right reserved.
Page 3
FEATURES
• Meets standards and requirements of MIL-STD810
• Built for professional use
• Multi- Coated Optics
• Built-in Rangefinder
• Full rubber armouring
• Waterproof & shockproof
• O-ring sealed & Nitrogen purged
• Two year warranty
SPECIFICATIONS
Magnification ............................................. 10X
Objective Lens Diameter ........................... 42 mm
Eye Relief .................................................. 10 mm
Minimum Focusing Distance ...................... 6 m
Field of View ............................................... 6°
Field of View at 1000 m .............................. 105 m
Exit Pupil Diameter .................................... 4.2 mm
Interpupillary Adjustments ......................... 56.5-75 mm
Max. Width ................................................. 5.2”/ 132 mm
Length ........................................................ 6.1”/ 155 mm
Weight ........................................................ 26.9 oz / 0.76 kg
* ATN reserves the right to change the above specifications at any time without notice
APPLICATION
ATN is proud to introduce its professional brand of daytime binoculars:
the Omega line. Years of manufacturing German quality glass for our
Night Vision equipment have allowed us to produce a binocular line
with exceptional qualit y at a reasonable price.
The Omega binoculars are technologically advanced with special
coated optics, nitrogen filled, durable rubber armour, and either a builtin range finder or a built-in compass. These binoculars are tough, provide a crystal clear image, and are of the highest qualit y.
Each model is durable enough to withstand the harshest conditions
and is designed to perform under the most stressful situations. This is
2
Page 4
guaranteed by the lifetime manufacturer’s defect warranty on all of the
models in the Omega line.
ATN’s 10x42RF daytime Omega class binoculars are the quintessential
professional binoculars. They provide a sharp stable image with excellent low-light performance.
Features multi-coated optics for superior light transmission, individual
diopter focus for clearer images, built-in range finder reticle and full
rubber armouring for increased shock resistance.
The combination of waterproof and high quality optics make it the perfect binocular for military, law enforcement, boating as well as for most
hunting uses.
Meets standards and requirements of MIL-STD810 for a lifetime of high
performance.
PREPARING THE BINOCULAR
Your ATN OMEGA Series binocular comes with a neck strap. We recommend that you install the neck strap and use it whenever you are
using the binocular.
NOTE : Many accidents can be avoided by using the neck strap.
ATTACHING THE NECK STRAP
Thread the neck strap through the neck strap loop on the body of the
binocular.
Bring the end of the strap back to the neck strap buckle. Thread the
ne ck strap end fro m th e back, through the buckle, as s how n in the illustration. This will secure the neck strap. Using the same procedure on
the other side, adjust the length of the neck strap for the comfort of the
user.
OCULAR LENS COVER
The ocular lens cover or “rain guard” has a loop for the neck strap to
thread through one side. This cover protects the ocular lenses from
debris and rain while the binocular is being carried by use of the neck
strap. The rain guard hangs down out of the way when the binocular is
being used.
ADJUSTING THE BINOCULAR FOR USE
All binoculars must be adjusted to the individual using the binocular.
The following procedures will assure maximum enjoyment and proper
use.
3
Page 5
INTERPUPILLARY DISTANCE ADJUSTMENT
Th is a djust ment uses the bino c ular s ’ hi nge p in to ad just to the d istan c e
between the user’s eyes. With the proper adjustment, the user sees a
round full circle, not two circles. Move the barrels in or out until a round
full circle is seen through the unit. With this adjustment made, you are
now ready to focus the binocular.
INDIVIDUAL EYE FOCUS SYSTEM
The OMEGA Series binoculars are equipped with the individual eye
focus system. This is the focus system preferred by military units around
the world. Once you adjust the binocular to your vision at approximately
100 yards, the unit will be in focus without additional adjustment to an
infinite distance.
To focus the binocular, close your right eye and look through the left
barrel. Turn the left ocular eyepiece to the right or left until you see a
shar p, clear i m a g e. Use t h e s a m e proc e d u r e for t h e r i g h t eye. Now your
binocular is focused.
Both r ight a n d l ef t o c ular eyepiece s hav e + / -d i o pt e r mark i n g s . R e m e m bering the setting or marking the diopter setting with a permanent
marker makes refocusing the unit easy if another person has used the
binocular and changed the settings.
TRIPOD ADAPTER
Your OMEGA Series binocular is designed to be used with a tripod
adapter for mounting the unit on a tripod or window mount. To use this
feature requires the use of a ATN tripod adapter. To install the tripod
adapter, unscrew the knurled cap that is centered on the hinge pin.
Under the cap is a 1/4x20 N.C. threaded hole. Follow the instructions
included with the tripod adapter for proper installation. Tripod adapters
are available from ATN or your spor t optic dealer.
NOTE : Severe damage to the binocular can occur if the tripod collapses
or is knocked over. It is recommended that the binocular be removed if
the user is not within arm’s reach of the tripod.
RANGEFINDER RETICLE
ATN 10x42RF Binocular Reticle displays the reticle on the right view
side. Reticle focus can be adjusted via an left side eyepiece diopter.
The 10x42RF reticle is universal for different distance. The Reticle has
the 5 to 10 mil increments in the center for long distance, large target
4
Page 6
ra nging ability an d si ngle mil, hal f mi l spacing on t he ou ter reticle quadrants for smaller targets or greater distances. An open Un-Obstructed
field of view is critical for Obser vation.
.5 mil
10 mils
1 mil
5 mils
RETICLE USE EX AMPLES
5
.5 mil
1 mil
5 mils
36 inch Target measured with
Mil-Reticle as: 6.5 mils tall.
Distance to target: 154 Yard s
.5 mil
5 mils
36 inch Target measured with
Mil-Reticle as: 5.25 mils tall.
Distance to target: 191 Yards
Page 7
.5 mil
.5 mil
1 mil
36 inch Target measured with
Mil-Reticle as: 3.5 mils tall.
Distance to target: 286 Yard s
36 inch Target measured with
Mil-Reticle as: 2.25 mils tall.
Distance to target: 450 Yard s
1 mil
MAINTENANCE
Your binocular is designed for years of trouble free use. Following a few
ser vice recommendations will ensure years of ser vice.
OCUL AR LENS COVERS
Ocular lens covers are provided to protect the objective lenses of your
binocular. Keeping the lenses protected when not in use reduces the
amount of dust or debris that settles on the lenses.
BINOCULAR CASE
A rugged binocular case is provided to protect your unit when travelling
and not in use.
CLEANING YOUR BINOCULAR
Keeping your binocular clean and dry will allow you maximum enjoyment and trouble-free service. Remove dust and debris with a soft
brush or compressed air.
If your binocular is used at sea, or near a salt-water environment, it is
strongly recommended that you rinse the binocular in fresh water. This
removes salt that may damage your unit.
6
Page 8
LENS CLEANING
Dust, salt and the oil left from fingerprint smudges should never be
allowed to remain on the lenses because they can harm the sensitive
multi-coatings applied to the lens surfaces.
Loose dust and debris should be removed by blowing the debris off,
using an optical lens cleaning brush or compressed air.
If fingerprints o r smudges remain o n the le n s , use an o p t i c a l lens tissue
and l e n s c l e a n e r s o l u t i o n to cl e a n the lenses. Fo l l o w th e instru c t i ons o n
the lens cleaning tissue and cleaner. Lens cleaning supplies are available from ATN or all camera or optical stores.
NOTE : Do not “over clean” lenses. Excessive cleaning can damage
lens coatings. Do not use household cleaners on the lenses of the binocular.
HELPFUL TIPS FOR BINOCUL AR USERS
• Never leave your binocular exposed to direct sunlight for extended
periods. This can cause damage to the armour coatings or eyepieces.
Th e d as hb o ar d o f an a u t om o bi le i s n ot a p r op er s t o ra g e l o ca t io n for yo u r
binocular, the sunlight is greatly magnified through the windshield.
• Use the neck strap as your “insurance policy” against dropping the
binocular.
• Never walk away from a binocular on a tripod; remove it if you are not
within arm’s length of the tripod.
• Store your binocular in its case and in a cool, dry lo cation.
• Avoid severe temperature fluctuations. For example, bringing it from
an extremely cold condition into a heated environment could cause
condensation build up.
7
Page 9
WARRANTY
2 YEAR PRODUCT WARRANTY
This product is guaranteed to be free from manufacturing defects
in material and workmanship under normal use for a period of 2
(two) years from the date of purchase. In the event a defect that is
covered by t he foregoing warrant y occ urs during the applicable pe riod stated above, ATN, at its option, will either repair or replace the
product, and such action on the part of ATN shall be the full extent
of ATN’s liability, and the Customer’s sole and exclusive remedy.
This warranty does not cover a product (a) used in other than its
normal and customary manner; (b) subjected to misuse; (c) subjected to alterations, modifications or repairs by the Customer of
by any party other than ATN without prior written consent of ATN;
(d) special order or “close-out” merchandise or merchandise sold
“as-is” by either ATN or t h e ATN dealer; o r (e ) merchandise that has
been discontinued by the manufacturer and either par ts or re plac e ment units are not available due to reasons beyond the control of
ATN. ATN shall not be responsible for any defects or damage that in
ATN’s opinion is a result from the mishandling, abuse, misuse, improper storage or improper operation, including use in conjunction
with equipment which is electrically or mechanically incompatible
with or of inferior quality to the product, as well as failure to maintain the environmental conditions specified by the manufacturer.
CUSTOMER IS HEREBY NOTIFIED THAT OPERATION OF THE
EQUIPMENT DURING DAYLIGHT HOURS OR UNDER ANY EXCESSIVE LIGHT CONDITIONS MAY PERMANENTLY DAMAGE
THE INTERNAL COMPONENTS OF THE UNIT AND SAID DAMAGE WILL NOT BE COVERED UNDER THIS WARRANTY. This
warranty is extended only to the original purchaser. Any breach of
this warranty shall be waived unless the customer notifies ATN at
the address noted below within the applicable warranty period.
The customer understands and agrees that except for the foregoing
warranty, no other warranties written or oral, statutory, expressed or
implied, including any implied warranty of merchantability or fitness
for a particular purpose, shall apply to the product. All such implied
warranties are hereby and expressly disclaimed.
8
Page 10
LIMITATION OF LIABILITY
ATN will not be liable for any claims, actions, suits, proceedings,
costs, expenses, damages or liabilities arising out of the use of this
product. Operation and use of the product are the sole responsibility of the Customer. ATN’s sole undertaking is limited to providing
the products and services outlined herein in accordance with the
terms and conditions of this Agreement. The provision of products
sold and services performed by ATN to the Customer shall not be
interpreted, construed, or regarded, either expressly or implied, as
being for the benefit of or creating any obligation toward any third
party of legal entity outside ATN and the Customer; ATN’s obligations under this Agreement extend solely to the Customer. ATN’s
liability hereunder for damages, regardless of the form or action, shall not exceed the fees or other charges paid to ATN by
the customer or customer’s dealer. ATN shall not, in any event,
be liable for special, indirect, incidental, or consequential
damages, including, but not limited to, lost income, lost revenue, or lost profit, whether such damages were foreseeable
or not at the time of purchase, and whether or not such damages arise out of a breach of warranty, a breach of agreement,
negligence, strict liability or any other theory of liability.
PRODUCT WARRANTY REGISTRATION
In order to validate the warranty on your product, ATN must receive
a completed Product Warranty Registration Card for each unit or
complete warranty registration on our website at www.atncorp.
com. Please complete the included form and immediately mail it
to our Service Center: ATN Corporation, 1341 San Mateo Avenue,
South San Francisco, CA 94080.
OBTAINING WARRANTY SERVICE
To obtain warranty service on your unit, End-user must notify ATN
service department by calling 800-910-2862 or 650-989-5100 or
via e-mail service@atncorp.com to receive a Return Merchandise
Authorization number (RMA). When returning please take or send
the product, postage paid, with a copy of your sales receipt to our
service center, ATN Corporation at the address noted above. All
9
Page 11
merchandise must be fully insured with the correct postage; ATN
will not be responsible for improper postage or, missing or dam-
aged merchandise during shipment. When sending product back,
please clearly mark the RMA# on the outside of the shipping box.
Pl e ase i n clud e a let te r t h at ind i cate s your RM A #, N a m e, Return Ad dress, reason for service return, Contact information such as valid
telephone numbers and/or e-mail address and proof of purchases
that will help us to establish the valid start date of the warranty.
Product merchandise returns that do not have an RMA listed
may b e r e f u s ed o r a significa nt de l ay in p rocessing may o c cu r.
Estimated Warranty service time is 10-20 business days. End-user/
customer is responsible for postage to ATN for warranty service.
ATN will c over r eturn postage /ship p i n g af ter war r a n t y r e p a ir to e n duser/customer only if product is covered by aforementioned warranty. ATN will return product after warranty service by domestic
UPS ground and/or domestic mail. Any other requested, required or
international shipping method the postage/shipping fee will be the
responsibility of the end-user/customer.
10
Page 12
For cu stomer ser vice and te ch nical support , please contact
American Technologies Network Corp.
North American Office
1341 San Mateo Avenue, South San Francisco, CA 94080
phone: 800-910-2862, 650-989-5100; fax: 650-875-0129
European Office
The following countries can use our to ll free number:
00 8 0 0 9102- 8 62 0
Austria, France, Germany, Holland, Italy, Spain, Sweden, Switzerland
For other countries, please use
38 048-7770214 or 38 04 8 -77703 45
www.atncorp.com
©2009 ATN Corporation
Loading...