Atmos InterSystem HE26, InterSystem HE40C, GC 41-249-05, GC 41-249-07 User Manual

Atmos

InterSystem

Installation & Servicing Instructions for HE26 & HE40C

(GC 41-249-05 & GC 41-249-07)

Atmos Heating Systems

West March

Daventry

Northants, NN11 4SA

Tel: [phone]

Fax: [phone]

e-mail: [e-mail]

internet: www.atmos.co.uk

Issue 01.11.11 (Main revision)

2

© 2011 Atmos Heating Systems

The information provided applies to the product in the standard model. Atmos Heating
Systems can therefore not be held liable for any damage resulting from the product
specifications that deviate from the standard model.

The information provided has been compiled with the utmost care. However, Atmos Heating
Systems cannot be held liable for any faults in the information nor for the consequences
thereof.
Atmos Heating Systems cannot be held liable for any damage resulting from the activities
carried out by third parties.

To be changed without prior notice

Building Regulations and the Benchmark Checklist

Building Regulations (England & Wales) require notification of the installation of a heating appliance in
a dwelling to the relevant Local Authority Building Control Dept. This can be achieved via a
Competent Persons Self Certification Scheme as an option to notifying the Local Authority directly.
Similar arrangements apply in Scotland and Northern Ireland.
Atmos Heating Systems is a member of the Benchmark Scheme and the Benchmark Checklist is
included at the back of these Instructions. The Benchmark Checklist provides a Commissioning
Checklist and Service Record to be completed by the Installer/ Service Engineer.

Benchmark places responsibilities on both manufacturers and installers.

The purpose is to ensure that customers are provided with the correct
equipment for their needs, that it is installed, commissioned and serviced in
accordance with the manufacturer’s instructions by competent persons and
that it meets the requirements of the appropriate Building Regulations. The
Benchmark Checklist can be used to demonstrate compliance with Building
Regulations and should be provided to the customer for future reference.

Installers are required to carry out installation, commissioning and servicing
work in accordance with the Benchmark Code of Practice which is available
from the Heating and Hotwater Industry Council who manage and promote
the Scheme. Refer to www.centralheating.co.uk for more information.

3

TABLE OF CONTENTS

1. Safety Regulations 7

1.1 General ....................................................................................................................................................................... 7

1.2 CH system................................................................................................................................................................... 7

1.3 Gas system ................................................................................................................................................................. 7

1.4 Electrical system ......................................................................................................................................................... 7

1.5 Domestic water system ............................................................................................................................................... 7

1.6 Flue discharge and air supply ..................................................................................................................................... 7

2. Description of the Appliance 8

2.1 General ....................................................................................................................................................................... 8

2.2 Operation .................................................................................................................................................................... 8

2.3 Operating conditions ................................................................................................................................................... 8

2.4 PC interface .............................................................................................................................................................. 10

2.5 Test programmes ...................................................................................................................................................... 10

3. Main Components 11

3.1 Accessories ............................................................................................................................................................... 12

4. Installation 13

4.1 Overall dimensions HE26 .......................................................................................................................................... 13

4.2 Overall dimensions HE40C ....................................................................................................................................... 14

4.3 Unpacking the appliance ........................................................................................................................................... 15

4.4 Additional dimensions ............................................................................................................................................... 15

4.5 Boiler location............................................................................................................................................................ 16

4.6 Mounting ................................................................................................................................................................... 17

4.7 Mount the appliance .................................................................................................................................................. 18

4.8 Fit the pipework cover (optional only for HE26) ........................................................................................................ 18

4.9 Condensate disposal ................................................................................................................................................. 19

5. Connections 20

5.1 Connect the CH system ............................................................................................................................................ 20

5.2 Connecting the gas supply ........................................................................................................................................ 21

5.3 Electrical connection ................................................................................................................................................. 22

5.4 General Flue Requirements ...................................................................................................................................... 25

5.5 Flue discharge and air supply ................................................................................................................................... 26

5.6 Roof outlet prefabricated chimney ............................................................................................................................ 32

5.7 Atmos MS System ..................................................................................................................................................... 33

5.8 Atmos Communal Flue System (CFS) ...................................................................................................................... 34

6. Commissioning 35

6.1 Fill and de-aerate the appliance and the system ...................................................................................................... 35

6.2 Commissioning of the appliance ............................................................................................................................... 36

6.3 System Shutdown ..................................................................................................................................................... 37

7. Setting and Adjustment 38

7.1 Directly via operating panel ....................................................................................................................................... 38

7.2 Settings through the service code ............................................................................................................................. 38

7.3 Parameters................................................................................................................................................................ 39

7.4 Setting maximum CH power ..................................................................................................................................... 40

7.5 Setting pump position ................................................................................................................................................ 40

7.6 Weather-dependent control ....................................................................................................................................... 41

7.7 Conversion to other gas type .................................................................................................................................... 41

7.8 Gas-air control........................................................................................................................................................... 41

7.9 Setting gas-air control ............................................................................................................................................... 42

7.10 Carbon monoxide : carbon dioxide ratio (CO/CO2 ratio) ........................................................................................... 43

8. Faults 44

8.1 Display last fault code. .............................................................................................................................................. 44

8.2 Burner does not ignite ............................................................................................................................................... 45

8.3 Burner ignites with much noise ................................................................................................................................. 45

8.4 Burner resonates ....................................................................................................................................................... 46

4

8.5 No heating (CH) ........................................................................................................................................................ 46

8.6 Reduced output ......................................................................................................................................................... 47

8.7 CH does not reach the correct temperature .............................................................................................................. 47

9. SERVICING THE BOILER AND COMPONENT REPLACEMENT 48

9.1 SERVICING THE BOILER ........................................................................................................................................ 48

9.2 COMPONENT REPLACEMENT ............................................................................................................................... 49

10. Technical Specifications 52

10.1 Electrical diagram HE26 ............................................................................................................................................ 53

10.2 Electrical diagram HE40C ......................................................................................................................................... 54

11. CE Declaration 55

NOTE The Benchmark Checklist & Service Record are included at the back of the Manual.

5

This manual

Using this manual you can safely install and maintain this appliance.
Carefully follow the instructions.

In case of doubt, contact Atmos Heating Systems.
Keep these instructions near the appliance.

Abbreviations and names used

Description

To be referred

to as

High Efficiency

HE

Atmos InterSystem wall

-

mounted gas heater

Appliance

Appliance with piping for central heating

CH system

Icons

The following symbols are used in this manual:-

CAUTION

Procedures that, when not carried out with due care,
may result in damage to the product or the
environment or in personal injury.

Service and technical support

For information about specific adjustments, installation, maintenance and
repair activities, please contact:

Atmos Heating Systems,
West March,
DAVENTRY,
Northants, NNII 4SA
Tel: [phone]; fax: [phone]
Email: [e-mail]; internet: www.atmos.co.uk

Environment

When the appliance needs replacement, your installer

may

arrange for disposal. Should this not be possible, then
make enquiries with your local council about the
possibilities for re-use or environmental-friendly processing
of the materials used, or contact a scrap dealer about
disposal.

Various plastics and metals have been used in producing
the appliance. Also, the appliance contains electronic
components that are electronic waste.

Intended use

The appliance as described in this documentation is intended for heating rooms
with a central heating system and, if required, heating hot water via an indirect
hot water tank. Any other use is outside the scope of intended use for this
appliance. Any liability for damage resulting from improper use shall not be
accepted.

6

Atmos Warranty – Short version

1. Atmos Warranty covers any material, construction or operation faults that are
found to be of original manufacturing origin. A full statement of the Atmos
Warranty can be found on www.atmos.co.uk.

2. Atmos boiler warranty is two years from date of invoice or 12 months from
date of installation, whichever is the later. This warranty covers the cost of
replacement parts and associated labour. However the ignition & ionisation
probe and the glass fuse are excluded from this warranty. The warranty for
the heat exchanger is 10 years in total, but this covers the cost of associated
labour only for the first two years from date of invoice.

3. There is no carriage charge for the delivery of replacement parts covered by
the warranty. Any alleged faulty part must be returned to Atmos carriage
prepaid. Carriage will be credited if the fault is found to be a manufacturer’s
fault.

4. The serial number of the boiler must be supplied with any warranty claim.

5. All products must be used in an appropriate application and manner. This
includes, but is not limited to, correct boiler sizing, system design, system
cleansing and use of corrosion inhibitors. If the boiler installed is a combi
boiler, an approved water conditioner device must be fitted in areas where the
water hardness exceeds 200ppm, as required by Building Regulations.

6. The Benchmark Checklist & Service Record, found in the back of the
installation Instructions, must be filled in. Failure to install and commission
according to the manufacturer’s instructions and complete the Benchmark
Commissioning Checklist invalidates the warranty.

7. The Warranty card must be completed and the signed Atmos copy must be
received within 14 days of installation together with a copy of the Benchmark
Commissioning Checklist, completed by the installer. By signing the Warranty
card the buyer agrees that the goods have been delivered in a satisfactory
condition.

Exceptions

8. In the event of full payment for a product not being received, Atmos shall be
discharged from all further contractual or warranty obligations.

9. Surface and/or transport damage are outside the scope of this warranty.

10. Any warranty provision shall not apply if Atmos determines that the fault is
due to improper application, use, neglect, accidental damage or injudicious
treatment, non-observance of instructions contained in Atmos Manuals or due
to improper repair, adjustment, installation or maintenance or due to work
carried out by unqualified engineers. The warranty also lapses if the Atmos
boiler has not had a yearly service in accordance with instructions.

11. This warranty shall not apply if the fault is caused by scale, failure or
abnormality of gas or water supply, or impact of any external influence that
adversely affects the normal operation of the product. This shall include but
not be restricted to dehydration, abnormal or high voltage, and hard water.

12. Excluded parts are the ignition & ionisation probe and the glass fuse as these
are subject to wear and tear in normal use.