Atmos Coopra Installation And User Manual

Download

MV030204 manual Atmos EN 35_40 - E000129013 w pump connection

Installation- and User Manual

Central Heating Boiler……………………………..…………..35C Central Heating Boiler……………………………..…………..40C

Wall hung, fan flue, room sealed gas boilers

E000129013

Atmos Heating Systems Installation and user manual EN_FMT

CONTENTS

CHAPTER 1.

1.1. Technical data 15B; 15C; 30K; 30B; 30C...............................................................................................

1.2. Dimensional sketch................................................................................................................................

1.3. Unit components.....................................................................................................................................

1.4. Diagrams..................................................................................................................................................

1.4.1 Functional flow diagram...........................................................................................................................

1.4.2. Verkabelungsplan...................................................................................................................................

1.5. Operation ...............................................................................................................................................

1.6. Boiler types............................................................................................................................................

1.6.1. Atmos 30K..............................................................................................................................................

1.6.2. Atmos 15B / 30B.....................................................................................................................................

1.6.3. Atmos 15C / 30C .................................................................................................................................

1.6.4. Difference between type 15 and type 30................................................................................................

1.7 Conditions of delivery.............................................................................................................................

1.8. Configuration of flue tube and air supply....................……………………….......………………..............

1.9. Environmental conditions.......................................................................................................................

1.10. Permitted flue resistance..........................................................................................................................

1.11. Heating of central heating water (all models).........................................................................................

1.12. Pump and hydraulic resistance ..............................................................................................................

1.13. HWS.......................................................................................................................................................

1.13.1. Heating of hot water (Combi-Boiler) ………………........…………………………………………...............

1.13.2. Heating of HWS (boiler with external storage cylinder) .........................................................................

1.14. Standards / Guidelines............................................................................................................................

1.15. General satety regulations.....................................................................................................................

1.16. Water quality...........................................................................................................................................

CHAPTER 2. INSTALLATION

2.1. Mounting the rear cabinet with expansion vessel...................................................................................

2.2. Mounting the assembly bracket..............................................................................................................

2.3. Water ans gas connections....................................................................................................................

2.3.1. Gas connection......................................................................................................................................

2.3.2. Central heating water connections..........................................................................................................

2.3.3. HWS connetionto the Combi-boiler.......................................................................................................

2.3.4. Hot water connection to boiler with external storage HWS cylinder........................................................

2.4. Seal on the waterside.............................................................................................................................

2.5. Draconin connection................................................................................................................................

2.6. Electricity connection.............................................................................................................................

CHAPTER 3. SUSPENDING THE UNTI

3.1. The unit ..................................................................................................................................................

3.2. Suspension............................................................................................................................................

3.3. Fitting the flue tube and air supply.........................................................................................................

3.3.1. Connenting the eccentric flue and air supply (2-pipe system)...............................................................

3.3.2. Connecting the concentric flue tube and air supply (80/125 mm adapter).............................................

3.3.3. Connecting the concentric flue tube and air supply (60/100 mm adapter).............................................

3.4. Condensation water drain/overpressure protection on drain..................................................................

3.5. Connection block....................................................................................................................................

3.5.1. On/off room thermostat (if applicable). Connect to terminals (1) and (2)...............................................

3.5.2. Modulating room thermostat (if applicable) . Connect to terminals (1) and (2)......................................

3.5.3. Connection for the external temperature sensor (if appicable) Connect to terminal (3) ans (4).............

3.5.4. Connection of the temperature sensor for the external HWS cylinder. Connect to terminal (5) and (6)

3.6. Assembling the connection block...........................................................................................................

3.7. Placing the jacket...................................................................................................................................

CHAPTER 4. COMMISIONING

4.1. Electrical power.......................................................................................................................................

4.2. Main switch.............................................................................................................................................

4.3. Filling......................................................................................................................................................

4.4. Reading the water pressure...................................................................................................................

4.5. Venting...................................................................................................................................................

4.6. Chimney sweeper function.....................................................................................................................

4.7. Gas / Air Ratio........................................................................................................................................

4.8. Gas / Air adjustment (CO

analysing).....................................................................................................

4.8.1. Full load..................................................................................................................................................

Atmos Heating Systems Installation and user manual EN_FMT

4.8.2. Low load..................................................................................................................................................

4.9. Placing the jacket...................................................................................................................................

4.10. Changing over to LPG-gas....................................................................................................................

4.10.1. Full load om Propane.............................................................................................................................

4.11. Display...................................................................................................................................................

4.11.1. Normal operation (permanent status indication)....................................................................................

4.11.2. blocking operation (permanent status indication)..................................................................................

4.11.3 Lock-out (flashing status indication).......................................................................................................

4.12. Menu structure.......................................................................................................................................

CHAPTER 5. TEMPERATURE REGULATIONS

5.1. Central Heating...........................................................................................................................................

5.1.1. Central heating temperature regulation with on/off thermostat without outside temperature sensor.........

5.1.2. Central heating temperature regulation with on/off thermostat with outside temperature sensor..............

5.1.3. Central heating temperature regulation with modulating thermostat with or without outside tempsensor..

5.2. HWS temperature regulations....................................................................................................................

5.2.1. Combi-boiler...............................................................................................................................................

5.2.1.1. HWS heat demand.....................................................................................................................................

5.2.1.2. End of hot water heat demand...................................................................................................................

5.2.1.3. Store heat demand.....................................................................................................................................

5.2.1.4. End of store demand..................................................................................................................................

5.2.2. Boiler with external HWS cylinder..............................................................................................................

5.2.2.1. HWS cylinder with external sensor without modulating space unit............................................................

5.2.2.2. HWS cylinder with external sensor with modulating space unit..................................................................

5.2.3. HWS cylinder with thermostat without modulating space unit....................................................................

5.2.4. HWS cylinder with thermostat with modulating space unit.........................................................................

CHAPTER 6 BURNER STATES and MONITORING

6.1. Burner states..............................................................................................................................................

6.1.1. Rest state...................................................................................................................................................

6.1.2 Purging/Prestart.........................................................................................................................................

6.1.3. Ignition........................................................................................................................................................

6.1.4. Operation....................................................................................................................................................

6.1.5. Post-ventilation...........................................................................................................................................

6.1.6. Functional locking.......................................................................................................................................

6.2. Monitoring...................................................................................................................................................

6.2.1. Monitoring the pump circulation..................................................................................................................

6.2.2. Pump programm.........................................................................................................................................

6.2.3. Pump test programm..................................................................................................................................

6.2.4. Static pressure monitoring..........................................................................................................................

6.2.5. Difference in temperature...........................................................................................................................

6.2.6. Maximum temperature limitation................................................................................................................

6.2.7 Flue gas temperature limitation..................................................................................................................

6.2.8. Flow sensor protection...............................................................................................................................

6.2.9. Frost protection..........................................................................................................................................

6.2.10. Monitoring the fan speed............................................................................................................................

6.2.11. Glow plug protection...................................................................................................................................

CHAPTER 7. MAINTENANCE

7.1. Annual maintenance..................................................................................................................................

7.1.1. Checking the CO

percentage on full load................………………………………………………………….

7.1.2. Measuring the load on the unit .................................................................................................................

7.1.3. Checking the condensation water drain.......……………………………………………………………………

7.1.4. Ionisation probe..........................................................................................................................................

7.1.5. Water pressure...........................................................................................................................................

CHAPTER 8. MALFUNCTIONS

8.1. Draining the unit.........................................................................................................................................

8.2. No signal on the display.............................................................................................................................

8.3. Fault code U/d or U/O (alternating U with a status code will appear on the display...................................

8.4. Unit does not respond to central heating heat demand..............................................................................

8.5. Unit does not respond to HWS demand......................................................................................................

8.6. Three-way-diverter valve............................................................................................................................

8.7. Check function of gas control.....................................................................................................................

8.8. Measuring the fan impedance....................................................................................................................

8.9. Fitting instructions for the pressure sensor................................................................................................

Atmos Heating Systems Installation and user manual EN_FMT

8.10. Fitting instructions for the safety valve.......................................................................................................

8.11. Malfunction code „F“ (flashing)...................................................................................................................

8.11.1. Gas control will not open (no voltage).......................................................................................................

8.11.2. Gas control will not open (gas inlet pressure too high)..............................................................................

8.11.3. Gas control will not open (coils defective)...................................................................................................

8.11.4. Gas/Air mixture is not correctly adjusted....................................................................................................

8.11.5. Check glow plug.........................................................................................................................................

8.11.6. Check ionisation current.............................................................................................................................

8.11.7 inspection / cleaning / replacement of the ionisation probe........................................................................

User manual

General......................................................................................................................................................................

Cleaning the unit.......................................................................................................................................................

Holidays....................................................................................................................................................................

Brrrr, the central heating is not working....................................................................................................................

Electricity and gas.....................................................................................................................................................

Water and air....................... .....................................................................................................................................

Other causes.............................................................................................................................................................

Display.............................................................. .......................................................................................................

Reset button..............................................................................................................................................................

Abbreviated display indications.................................................................................................................................

Atmos Heating Systems Installation and user manual EN_FMT

CHAPTER 1.

1.1. Technical data 35C / 40C

Boiler type 35 / 40

Gas type

natural gas G20 natural gas G25 LPG gas G30/G31

Mains voltage / Frequency 230 V / 50 Hz

Power consumption (max.) 144 W

Electrical data

Thermostat voltage 24 V

Height 600 mm

Width 360 mm

Depth 300 mm

Dimensions and weight

Weight 35 kg

CO2 10 – 100 ppm

CO (0% 02) 12 – 35 ppm

Emission value

NOX (0% O2) 10 – 30 ppm

at 80/60ºC < 70ºC

Flue gastemperature

at 50/30ºC < 35ºC

Maximum chimney resistance

Air feed and flue tube together

125 Pa

Gas Ø 15 mm

CH (flow and return) Ø 25 mm

Connections

Overflow Ø 15 mm

Eccentric Ø 60 – 60 mm

Air feed and flue tube system

Concentric Ø 80 / 125 mm

Water contents 0.8 L

Max. temperature 90°C

Boiler heat exchanger

Max. Water pressure 3 bar

Pump high 40 dB(A)

Sound level

Pump low 30 dB(A)

Certification

CE Identification number CE0063-AT3070

Boiler type 35

Gas type

natural gas G20 natural gas G25 LPG gas G30/G31

Nominal gas pressure 20 mbar 25 mbar 37/50 mbar

Heat input CH (gross) 8.1 – 38.5 kW

Heat input CH (net) 7.3 – 34.7 kW

Nominal output CH at 80/60ºC 7.2 – 33.7 kW

Nominal output CH at 50/30ºC 7.9 – 36.1 kW

Efficiency at 80/60ºC (net) Low load = 98.1 %; High load = 97.2 %

Gas technical data type 35

Efficiency at 50/30ºC (net) Low load = 108.4 %; High load = 104.2 %

Boiler type 40

Gas type

natural gas G20 natural gas G25 LPG gas G30/G31

Nominal gas pressure 20 mbar 25 mbar 37/50 mbar

Heat input CH (gross) 8.1 – 41.1 kW

Heat input CH (net) 7.3 – 37.0 kW

Nominal output CH at 80/60ºC 7.2 – 36.0 kW

Nominal output CH at 50/30ºC 7.9 – 37.9 kW

Efficiency at 80/60ºC (net) Low load = 98.1 %; High load = 97.2 %

Gas technical data type 40

Efficiency at 50/30ºC (net) Low load = 108.4 %; High load = 104.2 %

Atmos Heating Systems Installation and user manual EN_FMT

1.2. Dimensional sketch

Free space

There must be sufficient space at the top and bottom to be able to suspend the unit and to be able to connect all feed and drain pipes. Normally, roughly 300 mm is required. It is recommended to leave a free space of 150 mm on the left (for servicing reasons) and 50 mm on the right of the unit. The front of the unit must be easily accessible for servicing at all times.

Atmos Heating Systems Installation and user manual EN_FMT

1.3. Unit components

No Description Manufacturer Coopra article code

1 Primary heat exchanger Coopra n.a. 2 Manager Coopra n.a. 3 Pump Wilo N00S110006 4 5 6 Glow plug Saint Gobain N00S070014 7 Ionisation probe Sapco N00S070020 8 Burner type 30 / 40 Furigas N00S020000 9 Vapour tray Coopra N00S020015 10 Gas valve Honeywell N00S020009 11 Fan Vibo N00S020006 12 Venturi type 40 Honeywell N00S020008 13 Water pressure sensor Huba N00S080028 14 Return sensor Honeywell N00S070008 15 Flow sensor Honeywell N00S07008 16 Safety device Emmeti xxxxxxxx 17 Float vent Emmeti xxxxxxxx 18 19 Flue gas temperature sensor Tasseron N00S070017 20 Type plate Coopra n.a. 21 Condensation water overflow Coopra n.a. 22 Gas connection Coopra n.a. 23 Central heating return Coopra n.a. 24 Central heating flow Coopra n.a.

Atmos Heating Systems Installation and user manual EN_FMT

1.4. Diagrams

1.4.1. Functional flow diagram

FSP

-t

BURNER

FLOW X17.6

X7.1

X7.2

X7.4

X14

X6.4

X6.1

X12

X8.6

X8.2

X4.4

X3.5

X3.4

X3.2

X3.1

X22.2

X22.1

X4.6

X4.5

X4.3

X4.1

X8.5

X8.4

X8.3

X8.1

X6.3

X9.2

X1.3

X10.2

X11.2

X9.1

X1.4

X10.1

X11.1

X16.7

X16.6

X16.3

X16.2

X15.2

X15.1

X15.3

X18.1

X18.3

X17.5

X19.1

X17.2

X19.2

X17.3

ROOM THERMOSTAT 24VAC

ROOM THERMOSTAT 230VAC

EbV THERMOSTAT

OPENTHERM THERMOSTAT

PC CONNECTION

FLUE GAS

OUTSIDE

WATER PRESSURE +

RETURN

DHW INLET

EXTERNAL TANK

TANK THERMOSTAT

GLOW IGNITER

IONISATION

GAS VALVE

230 VRAC

COMBUSTION FAN

325 VDC

ALARM CONTACT

MAXIMAL THERMOSTAT

(OPTIONAL)

DISPLAY

230V 50 Hz

FURIMAT-990

DHW

X2.5

X2.4

X2.2

X2.1

X2.3

PUMP

230 VAC

THREE-WAY VALVE

230 VAC

Atmos Heating Systems Installation and user manual EN_FMT

1.4.2. Wiring diagram

Atmos Heating Systems Installation and user manual EN_FMT

1.5. Operation

A fan sucks the air required for the combustion through the air feed canal (A). Because the combustion air in the venturi sucks an under pressure, the correct amount of gas (G) is automatically added to the combustion air. The flammable gas/air mixture thus obtained is fed to the burner, via a mixing chamber, to be ignited at the surface of the burner by a ceramic glow plug. The hot combustion gases are efficiently fed through the heat exchanger, where they give their heat to the water. The flue gases are fed outside, through the flue tube (F), into a flue tube exhaust canal. The condensation water (H

O) thus obtained is discharged

into the sewer.

1.6. Boiler types

Atmos 40C

High efficiency boiler for central heating only.

The Atmos boiler is a heating unit with compact dimensions and a very high efficiency, with versions for domestic and small commercial use for central heating. The type plate, which specifies the type of gas etc. to be used, for which the unit is set, is on the left side of the unit. The unit is fixed to the wall with the aid of a separately delivered assembly bracket or rear cabinet.

1.7. Specific caracteristics type 40

1.7.1. Burner assy N00S020000

1.7.2. Primair heat exchanger N00S040005

1.7.3. Venturi N00S020008

1.7.4. Pump N00S110006

1.8. Conditions of delivery

Coopra Advanced Heating Technologies b.v. supplies its products according to the general conditions of delivery for the metal and electro technical industry. Registered with the Clerk of the District Court at Den Haag on 19 October 1998 under no. 119/1998.

Atmos Heating Systems Installation and user manual EN_FMT

1.8. Configuration of flue tube and air supply

See figure below for an overview of possible configurations. The units are approved for application on the drain systems: B23, C13(x), C33(x), C43(x), C53, C63(x), C83(x).

Preferably use flue tube materials, roof ducts and exterior wall ducts with a quality mark. With plastic drain materials, use a unit with a flue gas temperature sensor.

1.9. Environmental conditions

The area in which the unit is installed must satisfy the applicable regulations. The wall must be able to bear the weight of the unit (loaded weight approx. 40 kg). If you use a different assembly surface than a bricky wall of sufficient thickness, you must select suitable fixtures yourself and properly install the unit. The unit may not be fitted in a chemically aggressive environment. The unit with air feed and flue gas exhaust satisfies the requirements of protection class IP44 and may therefore be installed in a wet area. Although the unit is fitted with an internal frost protection, it may not be exposed to extremely low ambient temperatures (lower than -10°C).

1.10. Permitted flue resistance

The total resistance of the flue tube and air supply together may not be greater than 125 Pa.

Indication for the resistance values given in table below apply to a flow rate of 60 m

/hour.

dia. 80 mm

Tube per metre 5.0 Pa

Bend 90°, R = 1.5 D 6.5 Pa

Bend 90°, R = 0.5 D 15.0 Pa

Bend 45°, R = 1.5 D 4.0 Pa

Bend 45°, R = 0.5 D 5.5 Pa Roof duct (concentric,

1.25 m)

30.0 Pa

1.11. Heating of central heating water

If the room thermostat or space unit indicates that heat is required for the central heating, the unit will heat the central heating water as necessary. The power supplied is automatically adapted to the heat required and is also continuously variably adapted to the heat demand with the use of an on/off thermostat. When the thermostat indicates that the desired temperature has been reached, the central heating water is no longer heated. The central heating pump will continue to run for a previously set time to distribute the heat evenly over the heating installation.

A differential bypass valve must be installed on plants where it may happen that various radiators are simultaneously excluded from the circuit because of closure of control or zone valves.

The by-pass valve must be mounted in the installation between the flow and the return, provided that flow direction indicated by arrow is respected. To adjust the by-pass valve rotate knob of the graduated scale on setting 2.5-3.0. This value corresponds to the meters of pump head (m H2O). Lock the screw on the groove knob.

Atmos Heating Systems Installation and user manual EN_FMT

1.12. Pump and hydraulic resistance The pump characteristic and the resistance graph of the unit are given below.

If set on automatic function (menu setting) the electronics switches the speed of the pump to “high” or “low”, depending on the temperature demand:

• Dt > 30 °C : the pump runs „high speed“.

• Dt < 10 °C : the pump runs „low speed“.

Dt = Setpoint temperature deducted with the actual Flow temperature.

1.14. Standards / Guidelines

With the installation of the unit, all local regulations must be followed, where applicable, including the provisions of the following standards and guidelines:

• Building Regulations

• Regulations for natural gas installations

• Regulations for LPG (if applicable)

• Guidelines for existing gas installations

• Safety requirements for central heating

installations

• Safety provisions for low voltage installations

• General regulations for drinking water installations

• Water authority regulations

• Ventilation in dwellings

• Supply of combustion air and exhaust

• House sewerage in homes and dwellings

• Fire Brigade regulations

• Factory Act regulations

• Regulations applicable to HWS water Ask for the

locally applicable regulations at the local water company as they are different in some areas

1.15. General safety regulations

The installation may only be performed by a recognised installer. Take note that internal parts of the unit can carry a dangerous electrical voltage (230 Volt). Take note that the unit, the various pipes and the flue gas

exhausted by the unit can reach high temperatures (up to 90°C). Before carrying out maintenance activities in or on the unit, you must close the gas tap, switch off the electricity supply and pull the mains plug out of the socket.

1.16. Water quality

The composition and quality of the system water has a direct effect on the performance of the total system and the life of the boiler heat exchanger. Great care must be used with the addition and use of chemicals, water softeners, oxygen binders, de-aerators, aerators and water filters as they increase the chance of malfunctions. Corrosive elements of certain additives can attack the system and cause leakages; the build-up of undesired deposits generally leads to fatal damage of the heat exchanger.

00,2

0,2

0,3

0,6

Flow [m³/h)]

Pressure [bar]

0,7

0,5

0,4

0,1

0,4 0,6 0,8 1,0 1,2 1,4 1,6 1,8 2,0

Pump state high

Pump state low

Boiler resistance

2,2 2,4 2,82,6 3,0

0,8

Atmos Heating Systems Installation and user manual EN_FMT

CHAPTER 2. INSTALLATION

2.2. Mounting the assembly bracket

To mount the assembly bracket on a brick wall of sufficient thickness, use the screw plugs that are supplied. When you have determined the place of assembly, proceed as follows:

1. Draw the position of the hole (1) in the strap of the assembly bracket.

2. Use a masonry drill of 8 mm diameter to drill a hole with a sufficient depth in the wall.

3. Keep the hole (1) in the assembly bracket in front of the hole in the wall and fit one of the screws supplied through the assembly bracket in the hole.

4. Align the assembly bracket with the aid of a spirit level.

5. Use a masonry drill of 8 mm diameter to drill holes with a sufficient depth in the wall through the two bottom holes (2) in the assembly bracket.

6. Fit two of the screws supplied in the bottom holes.

7. When using assembly brackets with ac lamping plate for eccentric flue tube and air feed connection:

- Use a masonry drill of 8 mm diameter to drill a hole with a sufficient depth in the wall through the hole in the clamping plate and fit a nail plug in this hole.

- Fit the clamping plate at right angles.

8. Fix the assembly bracket firmly by tightening all screws.

Atmos Heating Systems Installation and user manual EN_FMT

2.3. Water and gas connections

2.3.1. Gas connection

• Connect the gas pipe to connection (5).

• Install the gas pipe stress free.

• Include an approved stopcock in the pipe.

• Carefully blow the gas pipe clean.

2.3.2. Central heating water connections

• Connect the central heating flow pipe to connection (2.

• Connect the central heating return pipe to connection (1.

• A differential bypass valve must be installed on plants where it may happen that various radiators are simultaneously excluded from the circuit because of closure of control or zone valves.

• Install a filling and draining device in the central heating system. Do not use the overflow valve as a drain. The overflow valve is a safety valve that ensures that the system is not subjected to a too high pressure (max 3.0 bar).

• Stopcocks must be fitted in the central heating flow pipe (2) and the central heating return pipe (1).

• The central heating return pipe (1) must be fitted with a suitable expansion vessel. The size of the expansion vessel must be determined on the basis of the central heating water temperature and the total water content the installation contains.

• If it may be expected that the central heating water will be severely contaminated by under floor heating, fitting is a 2 kg dirt filter in the return pipe is recommended. Atmos cannot give a guarantee for damage to the unit that is caused by dirt in the system.

• Before connecting the boiler unit, rinse the system completely to remove all contamination.

2.4. Seal on the waterside

With the use of the group of taps, you can now make a check on the seal on the waterside of the system.

2.5. Draconin connection

There must be a connection for the removal of the condensation water to the drain. This connection must be fitted with a trap to prevent smell problems. A tundish connection must be made because of possible overpressure or underpressure in the drain. Fit the condensation drain pipe (6) (inner diameter 40 mm minimum) several centimetres left of the gas pipe.

2.6. Electricity connection There must be an electrical outlet with earth connection available at a maximum distance of 1 m from the unit.

The electricity connection (230 VAC) must consist of live, neutral and earth A good earth connection is a requirement for good operation of the unit.

Atmos Heating Systems Installation and user manual EN_FMT

CHAPTER 3. SUSPENDING THE UNIT

3.1. The unit

Before unpacking the unit, check whether the type of gas to be used corresponds with the specification on the packing. If you have any questions, contact your supplier. To prevent back injury, take account of the fact that the weight of the unit is roughly 35 kg.

3.2. Suspension

Place an O-ring in the middle of each of the connections present (1) - (5). Remove the caps from the pipes of the unit. Keep the unit straight against the wall at about 5 cm above the site of the mounted assembly bracket or the assembly cabinet. Press the unit into the guide and let it drop carefully, so that the hook on the suspension bracket falls into the opening at the rear of the unit and the pins at the bottom of the unit fall in the corresponding openings in the suspension bracket. Here, the connection pipes of the unit fall over the connection points of the suspension bracket. Firmly tighten the union nuts of each of the connections present (1) to (5) with the aid of a spanner.

3.3. Fitting the flue tube and air supply

3.3.1. Connecting the eccentric flue and air supply (2pipe system)

When the flue tube and air supply are connected eccentrically, proceed as follows:

1. Fit the flue tube in the opening, in the suspension bracket.

2. Let the pipe protrude 30 -35 mm under the clamping plate. Slide the sliding piece (1) upwards over the flue tube.

3. Fit the air supply in the opening in the suspension bracket.

4. Let the pipe protrude 40 - 45 mm under the clamping plate.

5. Fit the rubber bellows over the air supply pipe and seal them with the hose clip.

6. Fit the clamping plate on the suspension bracket and tighten it with the three screws supplied. Take care here

that the clamping plate falls in the groove of the sliding piece.

3.3.2. Connecting the concentric flue tube and air supply (80/125 mm adapter)

When the flue tube and air supply are connected concentrically, proceed as follows:

1. Fit the 80/125 mm adapter on the unit before you place the unit.

2. After you have placed the unit, fit the concentric pipes on the 80/125 mm adapter.

3.3.3. Connecting the concentric flue tube and air supply (60/100 mm adapter)

When the flue tube and air supply are connected concentrically, proceed as follows:

1. Fit the 60/100 mm adapter on the unit before you place the unit.

2. After you have placed the unit, fit the concentric pipes on the 60/100 mm adapter.

3.4. Condensation water drain/overpressure protection on drain

Make a tundish between the condensation water drain/overpressure protection of the unit and the drainpipe.

3.5. Connection block

The connections of the green connection block are all voltfree contacts. Therefore, do not connect 230 Volts to them!

terminals (1) - (2)

Connection for 24 Volt thermostat

terminals (3) - (4)

Connection for 12 kOhm external temperature sensor

terminals (5) - (6)

Connection for 10 kOhm or 12 kOhm sensor of external cylinder

If no on/off room or modulating room thermostat is used at all, terminals (1) and (2) must be connected by wire.

3.5.1. On/off room thermostat (if applicable). Connect to terminals (1) and (2)

The on/off room thermostat (24 V) must be fitted in the same building as the unit. Strip about 5 mm off the insulation of the wires of the room thermostat. Stick the stripped ends of the wires into connections (1) and (2) of the connection block. Make sure that the wires do not make a short circuit. Firmly tighten the screws in the connection block.

3.5.2. Modulating room thermostat (if applicable). Connect to terminals (1) and (2)

The modulating room thermostat must be fitted in the same building as the unit. Strip about 5 mm off the insulation of the wires of the room thermostat. Stick the stripped ends of the wires into connections (1) and (2) of the connection block. Make sure that the wires do not make a short circuit. Firmly tighten the screws in the connection block.

Atmos Heating Systems Installation and user manual EN_FMT

When using a modulating thermostat, the plug on the printed circuit board must be connected with the correct polarity. To reach the printed circuit board, the black casing must be opened. Connect the plug for the relevant modulating space unit to terminal a, b or c, according to the following photograph.

a White

Connection for an on/off room thermostat

24 Volt

b Red

Connection for RS30 with Coopra protocol

EBV space regulation

c Blue Opentherm connection

Honeywell or TEM space regulation

3.5.3. Connection for the external temperature sensor (if applicable). Connect to terminals (3) and (4)

If an external sensor is connected, this temperature sensor must be an NTC with a resistance of 12 kOhm at 25°C.

Strip about 5 mm off the insulation of the wires of the sensor. Stick the stripped ends of the wires into connections (3) and (4) of the connection block, see figure

8. Make sure that the wires do not make a short circuit. Firmly tighten the screws in the connection block. If an external sensor is not used, terminals (3) en (4) can remain open.

3.6. Assembling the connection block

Connect the green connection block in the green socket.

3.7. Placing the jacket

Place the jacket in the appropriate hooks at the top of the unit. Let the jacket pivot until it falls over the unit. Tighten the fastener at the bottom of the jacket.

Atmos Heating Systems Installation and user manual EN_FMT

CHAPTER 4. COMMISSIONING

4.1. Electrical connection 230 VAC

• If the boiler is provided with a supply cord and a plug the appliance must be positioned so that the plug is accessible.

• If the boiler is not provided with a supply cord without a plug the supply must have a contact separation of at

least 3 mm in all poles.

If the supply cord is damaged, it must be replaced by the service agent or similarly person in order to avoid a hazard.

4.2. Main switch

To power up the appliance please switch the main switch on.

If the display of the unit gives the status code ‘U’ (alternately with an arbitrary

other code), this means the live and neutral connections are reversed. Isolate the supply and reverse the connections.

4.3. Filling

During filling with water, the unit must be connected to the mains and be switched on. Fully open all radiator taps. Connect the water supply to the filling connection. If the unit is not yet filled with water, the display shows a flashing ‘P’. The two numbers on the display give the water pressure. Open the tap to fill the system with water. When the water pressure is sufficient (> 1.3 bar), the flashing ‘P’ disappears from the display. Close, after filling, the filling tap again.

4.4. Reading the water pressure

It is possible to read the water pressure directly from the display. To do this, press the + button of the display for a minimum of 5 seconds.

The unit switches out of the menu back to normal operation:

• automatically after about 5 minutes;

• or if you press the - button of the display shortly.

4.5. Venting

After filling, the heating installation must be vented.

Proceed as follows: Follow the instructions from the manufacturer/installer for the venting of possible other elements of the heating installation, such as underfloor heating. Fully open all radiator taps. Open the air bleed cocks of the radiators one at a time. Use an air bleed key for this. As soon as water comes out of the air bleed cock, shut the cock off again.

4.6. Chimney sweeper function

The chimney sweeper function has priority over the central heating and HWS regulation.

The chimney sweeper function is activated by simultaneously pressing the "+ and the – buttons" of the display in for longer than 5 seconds.

The ionisation current can be read in microamperes in the two right segments.

The capacity that is immediately released is the maximum central heating capacity.

Press the "- button" to

go to low load.

Press the "+ button" to switch back to the preset full load capacity.

4.7. Gas / Air Ratio

(1). Venturi screw – Full load adjustment Turn the venturi screw anti-clockwise to increase

the CO2

value, clockwise to decrease it

. (2). Gas control screw – Low load adjustment Turn the screw anti-clockwise to decrease the CO2 value on low load, clockwise to increase

it.

(3). Cover screw

Atmos Heating Systems Installation and user manual EN_FMT

Pre-adjustment to be done in voltage-free

condition:

- LPG

GAS

– Turn venturi-screw clockwise 3

completely down on its seat. Then turn the venturi screw anti-clockwise 4 for 2 complete turns.

- N

ATURAL GAS

– Turn venturi-screw clockwise 3

completely down on its seat. Then turn the venturi screw anti-clockwise 4 for 4 complete turns.

With a vernier callipers the distance between venturi-screw (1) and the Top of the venturi-stud (1) has to be measured to find the rough setting of the venturi screw for full load, and depending of the used gastype. The exact adjustment of the setting has to be made using the CO

analysing method as described below.

4.8. Gas / Air adjustment ( CO

analysing)

The gas control is set in the factory to the type of gas to be used. This type of gas is stated on the packing and on the identification plate. To check the setting, you have to make a flue gas analysis.

Proceed as follows

Remove the measuring cap from the flue tube. Fit the measurement probe of a flue gas analyser (CO

meter) in the measurement opening of the flue tube canal. Make sure there is sufficient heat dissipation through the

heating.

CO2 setting

At full central

heating load

(P=100%)

At low load

Natural gas

(G20, G25)

8,8-9.4 % CO2 8,2-8,6 % CO2

Propane (G31) 9,8 % CO2 9,2% CO2

4.8.1. Full load

The burner has to burn at maximum central heating capacity (Menu setting P=100%).

Activate the chimney sweeper function on full load.

Read the CO

value on the analyser. If the value does not correspond with the value in the "CO

setting" table, carefully adjust the venturi screw (1). Turn the venturi screw anti-clockwise to increase the CO2 value, clockwise to decrease

it.

4.8.2. Low load

Activate the chimney sweeper function on low load

Read the CO

value on the analyser. If the value does not correspond with the value in the "CO

setting" table, carefully adjust the gas control adjusting screw (2). To do this, temporarily remove the cap (3) with the aid of a Torx screwdriver.

Turn the screw anti-clockwise to decrease the CO2 value on low load, clockwise to increase it

At the end of the flue gas analysis, set the central heating capacity (P) in the menu again to the value that is best suited for the application.

4.9. Placing the jacket

Place the jacket in the appropriate hooks at the top of the unit. Let the jacket pivot until it falls over the unit. Tighten the fastener at the bottom of the jacket.

4.10. Changing over to LPG-gas

First: the venturi adjusting screw fully clockwise until it blocks.

Fit a flue gas analyser (CO

meter) in the measurement opening of the flue tube canal.

4.10.1. Full load on Propane

Set in the menu the capacity “P” to 100%.

Activate the chimney sweeper function on full load.

Unscrew the venturi adjusting screw four full turns anticlockwise. (A guide for the dimension from the top of the screw to the top of the support is 16.1 mm).

Read the CO

value on the flue gas analyser. If the value does not correspond with the value for propane gas G31 (9,8% CO2), carefully adjust the venturi screw until the correct value is obtained.

If the gas control is already properly adjusted for natural gas, then the low load will not need to be adjusted. Activate the chimney sweeper function on low load. Check the CO2 value at

minimum capacity for propane gas G31 (9.2% - 9.5% CO

). If necessary, adjust the gas regulator screw until the correct value is obtained. Note that this setting is a critical one.

PRE- ADJUSTMENT MEASUREMENT:

Distance between Venturi-screw (1) and the Top of the venturi-stud to be about:

 12.5 mm for natural gas G25  14.1 mm for natural gas G20  16,5 mm for LPG gas G31

Atmos Heating Systems Installation and user manual EN_FMT

4.11. Display

A = display B = + button C = Set / Reset D = Status display E = - button

During operation, the display shows the status of the unit in the form of a code. To be able to read the codes, open the cover in front of the display. The display consists of three 7-segment LED’s + three decimal points and three pushbuttons. The left 7-segment LED shows the status or the menu step. The two right 7-segment LED's show the temperature, the pressure or the parameter value.

4.11.1. Normal operation (permanent status indication)

The Normal operation is to indicate the burner action.

- - Initialisation after restoration of supply power O No heat demand, stand-by C Central heating heat demand, burner off

C. Central heating heat demand, burner on P/C. Central heating heat demand, low load water pressure A/C. Central heating heat demand, low load chimney temperature

c Central heating pump post-running

b Burner off / post-running of pump for external HWS cylinder

b. Burner on

P/b. Boiler, low load by water pressure A/b. Boiler, low load by chimney temperature

O Frost protection burner off pump running 8C

o. Frost protection burner on 3C

C (flashing) Chimney function (temp display max/min/ionisation)

4.11.2. Blocking operation (permanent status indication)

The burner stopped burning due to an incorrect situation. The display gives a permanent indication (not flashing) and the operation can be restored by switching it off and on (volatile block).

code

Reversed neutral and line

Power supply line not correctly connected

1 Flow sensor open circuit

Faulty flow sensor Wiring interrupted or not correctly connected

1. Flow sensor short circuit

Faulty flow sensor Faulty wiring

2 Return sensor open circuit

Faulty return sensor Wiring interrupted or not correctly connected

2. Return sensor short circuited

Faulty return sensor Faulty wiring

4 Flue gas sensor open circuit

Faulty flue gas sensor Wiring interrupted or not correctly connected

6 Cold water sensor open circuit n.a.

6. Cold water sensor short circuited n.a. A Flue gas temperature > 80°C The burner is reduced to low load H Flow sensor > 105°C while the burner was off Reset the supply power by the on/off switch E Internal error Reset the supply power by the on/off switch

P Pump test / Start function blocking / Water pressure

Check the central heating system pressure Seized or faulty pump or faulty pump wiring Faulty pressure sensor or wiring

nc Burner Manager fault Reset the supply power by the on/off switch

4.11.3. Lock-out (flashing status indication)

In case of lock-out the display gives a flashing indication and the operation can be restored by pressing the reset button, placed on the control panel.

1 Boiler does not pass start temperature test Check system water flow; second system pump 2 Too many restarts

Internal regulation fault / A/D conversion fault /

external sensor fault /Too many restarts 5 Fan fault 7 Gas valve fault 8 Flame detected with closed gas valve Check gas valve

A Flue gas temperature > 95°C Check why flue gas becomes temperature > 95°C E Internal interlock fault Reset the supply power by the on/off switch H Flow sensor > 105°C with burner on Check system water flow

F Too many ignition attempts

O Gas valve connection Check short cut wire on print board terminal X4

Atmos Heating Systems Installation and user manual EN_FMT

4.12. Menu structure

By pressing the set/reset button in for longer than 5 seconds, you go to the ‘mode’ menu.

To change the subsequent "Letter" parameter, the user must press the Set/Reset button.

To change the “Range” setting in the parameter, the user must press the “+” or the “–“ button.

Letter Description Range Factory setting Field of application

max. set point of central heating 25°C - 90°C 82°C

Central heating post-running time 1 - 25 min, CO = 24 hours 5 min

Max central heating capacity 33 – 100 % 80 %

Type of application

0 = central heating unit

1 = n.a.

2 = for external HWS cylinder 12kOhm

3 = for external HWS cylinder 10kOhm

4 and 5 = all functions are blocked

unit-dependent unit-dependent

Set point for storage HWS cylinder 40°C -70°C 60°C

external storage vessel

O/b

Basic temperature

External characteristic

10 -70°C 20°C

O/S

Slope

External characteristic

1-100 20

O/d

Day reference temperature 0°C -70°C 20°C

These three settings are only active when an external sensor is connected

Factory setting

= Factory setting

= Changed factory setting

If you switch back to the factory setting, this has no effect on the H, S and P/S settings

Pump speed

00 = automatic

= always high

= always low

00 = automatic

P/S

Maximum pressure jump

= 0.54

= 0.53

= 0.52

= 0.54

In the View mode, you can read the actual values of:

8 = Water pressure (in bar)

1 = Flow temperature (in °C)

2 = Return temperature (in °C)

3 = Inlet cold water temperature / HWS sensor (in °C)

4 = External temperature (in °C)

5 = Outside temperature (in °C)

6 = Flue gas temperature (in °C)

7 = Flame signal (in µA DC)

9 = Last interlock

A = Last blocking

Atmos Heating Systems Installation and user manual EN_FMT

CHAPTER 5. TEMPERATURE REGULATIONS

5.1. CENTRAL HEATING

The permissible central heating flow temperature can be set between 40°C and 90°C. The burner is blocked when the set flow temperature is reached. During the first 60 seconds of a central heating heat demand, the flow temperature may rise to 3°C above the set point before the regulation locks.

5.1.1. Central heating temperature regulation with on/off thermostat without outside temperature sensor

Increasing set point

When the room thermostat is closed (heat demand), the set point (desired central heating flow temperature) rises at a rate of 2°C per minute until the maximum permissible central heating flow temperature is reached (21 minutes from minimum 40°C to 82°C).

Falling set point

When the room thermostat is open (end of heat demand), the set point (desired central heating flow temperature) falls at a rate of 4°C per minute to the minimum central heating temperature (10.5 minutes from 82°C to minimum 40°C).

Burner is on

• when the room thermostat is closed (heat demand)

• and when the actual flow temperature is 5°C below

the set point (desired central heating flow temperature)

• and after 3 minutes anti-reciprocital time, if applicable

Burner is off

• when the room thermostat is open (end of heat demand)

• when the actual flow temperature is 3°C above the set point (blocking)

• or when the actual flow temperature is 3°C above the maximum permissible central heating temperature.

During the set central heating post-running time, the pump will continue to run over the central heating circuit in low load.

5.1.2. Central heating temperature regulation with on/off thermostat with outside temperature sensor

Set point

The desired central heating flow temperature (set point) is calculated on the basis of the measured outside temperature and the [O/S] - [O/d] - [O/b] parameters set in the menu.

In formula form:

Set point of central heating = (20°C – outside temperature)*[O/S] /10 + [O/d]

Letter

Description

Range

default

O/b Basic temperature 10 –70 °C 20 °C O/S Slope 1 – 100 20 O/d Flow temperature at

outside = 20°C

0 –70 °C 20°C

C Max. Flowtemp. for

central heating

25 –90 °C 82°C

Heating curve

O/b-value: The setting of the minimal Heating flow temperature ( value in °C).

O/S-value : The setting for the sloop of the curve.

( change of Flow temperature depending on the change of the outside temperature).

O/d-value : The setting of the flow temperature at an outside temperature of 20°C ( value in °C).

Parameter „C“

The setting in the menu „C“ makes the maximal heating flow temperature ( default 82°C).

Burner is on

• when the room thermostat is closed (heat demand)

• and when the actual flow temperature is 5°C below

the set point (desired central heating flow temperature)

• and after 3 minutes anti-reciprocital time, if applicable, after a reciprocital stop

Burner is off

• when the room thermostat is open (end of heat demand)

• when the actual flow temperature is 3°C above the set point (blocking)

• or when the actual flow temperature is 3°C above the maximum permissible central heating temperature.

During the set central heating post-running time, the pump will continue to run over the central heating circuit in low load.

Outside temperature in °C

O/S=20 [default]

Parameter C=82°C [default]

Outside temperature [°C]

Supply temperature [°C]

O/d=20°C [default]

O/b=20°C [default]

Atmos Heating Systems Installation and user manual EN_FMT

5.1.3. Central heating temperature regulation with modulating thermostat (EBV or Opentherm) with or without outside temperature sensor

Set point

The set point indicates whether there is a heat demand.

- Without an outside temperature sensor, the desired central heating flow temperature (set point) is calculated by the modulating room thermostat.

- With an outside temperature sensor, the measured outside temperature is sent to the modulating room thermostat, which uses it to calculate the desired central heating flow temperature (set point).

Burner is on

• when the room thermostat is closed (heat demand)

• and when the actual flow temperature is 5°C below

the set point (desired central heating flow temperature)

• and after 3 minutes anti-recycling time, if applicable

Burner is off

• when the room thermostat is open (end of heat demand)

• when the actual flow temperature is 3°C above the set point (blocking)

• or when the actual flow temperature is 3°C above the maximum permissible central heating temperature.

During the set central heating post-running time, the pump will continue to run over the central heating circuit in low load.

5.2. HWS temperature regulations

5.2.2. Boiler with external HWS cylinder

The regulation is made on the basis of flow temperature with a normal cylinder thermostat function, on off.

5.2.2.1. HWS cylinder with external sensor without modulating space unit

The unit switches the heating of the storage HWS cylinder off when the return sensor has reached the desired final temperature of the HWS cylinder.

There is a burner demand when the flow temperature is lower than 85°C and the return temperature is lower than the desired HWS cylinder temperature.

With HWS cylinder heat demand, the pump state is high.

5.2.2.2. HWS cylinder with external sensor with modulating space unit

The modulating thermostat will generate a desired HWS temperature value.

The unit switches the heating of the cylinder off when the return sensor has reached the desired final temperature of the HWS cylinder. There is burner demand when the flow temperature is lower than 85°C and the return temperature is lower than the desired HWS cylinder temperature.

With HWS cylinder heat demand, the pump state is high.

5.2.3. HWS cylinder with thermostat without modulating space unit

There is HWS cylinder heat demand when the HWS cylinder thermostat is closed.

The unit switches the heating of the HWS cylinder off when the return sensor has reached the desired final temperature of the HWS cylinder There is burner demand when the flow temperature is lower than 85°C and the return temperature is lower than the desired HWS cylinder temperature.

With HWS cylinder heat demand, the pump state is high.

5.2.4. HWS cylinder with thermostat with modulating space unit

The modulating thermostat will generate a desired hot water temperature value.

There is heat demand when the HWS cylinder thermostat is closed. The unit switches the heating of the HWS cylinder off when the return sensor has reached the desired final temperature of the HWS cylinder. There is burner demand when the flow temperature is lower than 85°C and the return temperature is lower than the desired HWS cylinder temperature.

With HWS cylinder heat demand, the pump state is high.

Atmos Heating Systems Installation and user manual EN_FMT

CHAPTER 6. BURNER STATES / MONITORING

6.1. Burner states

6.1.1. Rest state

Fan off - Gas valve off - Igniter off - Ionisation off

During the rest state, a check is made to see if there is burner demand. If a false flame signal is detected during the rest state for more than 5 seconds, the Manager locks. If the glow plug counter is too high (too many Starts), the regulation blocks the burner demand. If there is burner demand and no blocking, the system will go over to purging/preheating.

6.1.2. Purging/Prestart

Fan off - Gas valve off - Igniter off - Ionisation off

The fan is switched on at the desired purging speed. The glow plug is switched on at the same time as the fan. After a few seconds, the fan goes from purging speed to the faster ignition speed. If a false flame signal is detected during purging, the regulation locks. If this lock is present for more than 5 seconds, the regulation locks with ‘8’:

6.1.3. Ignition

Fan on - Gas valve on - Igniter on/off - Ionisation off/on

The fan is running at the ignition speed. The gas valve is activated. The Glow plug will be switched off as soon as an ionisation signal is measured. If there is no ionisation at the end of the safety time, a new attempt at ignition will be made if this was not the last permitted attempt at starting. Here, there will first be postignition failure ventilation see 8.5. If there is ionisation at the end of the safety time, the system continues with operation:

6.1.4. Operation

Fan off - Gas valve off - Igniter off - Ionisation on

The fan is running at the required modulation speed. If the ionisation fails, a restart is made, providing this is not the third time within the burner demand. If this is the third time, the Manager will lock. The restart runs through post-ventilation purge, see 8.5. If the burner demand ends, the system goes to postventilation purge, see 8.5.

6.1.5. Post-ventilation

Fan on - Gas valve off - Igniter off - Ionisation off

The fan runs at the last demanded speed if the postventilation is running at the end of the burner demand and in all other cases at the highest speed. If a false flame signal is detected during purging, the regulation locks. If this lock is present for more than 5 seconds, the regulation locks with ‘?’: With end of post-ventilation purging after the end of the burner demand, a start test is run through:

6.1.6. Functional locking

Fan on/off - Gas valve off - Igniter off - Ionisation off - Alarm contact on

During functional locking, the pump is on the central heating circuit. At the beginning of the interlock, in the fault table is updated With some instances of interlock, the fan will post-ventilate for 1 minute at 50% of the maximum speed.

6.2. Monitoring

6.2.1. Monitoring the pump circulation

The pump is switched off for 3 seconds for each burner start. At the same time, the purging/prestart time starts. The static pressure is measured. After this, the pump is switched to a high speed. The purging time starts as soon as the pump speed has reached the desired value. At the end of the purging/prestart time, the active pump pressure is measured. If the difference between the active and the static pump pressure is less than 0.05 bar, the regulation locks and goes to the pump test program. If the difference is more than 0.54 bar, the regulation locks and goes to the pump test program. If the difference is between 0.05 and 0.54 bar, the ignition time starts. When the pump is switched to the low state during ignition, the pressure increase monitoring is switched off.

After the ignition time, the flow monitoring is realised by the flow/return sensor. If the temperature rise is large enough, the pump modulation is released. If the pressure changes afterwards by more than ± 0.1 bar (± 0,27 bar with changing pump speed) within 4 seconds, the regulation will block and switch over to the pump test program. With switching over from central heating to hot water during operation, the pressure fluctuation detection is defeated for 16 seconds.

6.2.2. Pump program

If the temperature difference between flow and return is greater than 30°C, the pump switches to a high speed. When the temperature difference drops below 10°C again, the pump switches back to a low speed. If the pump is on for a HWS demand with a Combi-unit or for cylinder heat demand, the pump is continuously at high.

6.2.3. Pump test program

The pump is switched off for 15 seconds and high for 15 seconds. The display shows ‘P’. The initial pressure is measured before the pump is switched on. The test pressure is measured 3 seconds after the pump is switched on. If the difference between these two pressures is greater than 0.20 bar and less than 0.54 bar, the pump test is finished.

Atmos Heating Systems Installation and user manual EN_FMT

6.2.4. Static pressure monitoring

If the water pressure is less than 0.2 bar, the regulation locks with a ‘P’ + ‘pressure’ on the display. This lock is removed when the water pressure goes above 1.3 bar. With a water pressure between 0.5 and 0.2 bar, the burner is limited to low load. The display shows alternately the ‘P’ and the normal status display. If the water pressure is greater than 3.0 bar, the regulation locks with a ‘P’ + ‘pressure’ on the display. This lock is removed when the water pressure goes below 2.9 bar.

6.2.5. Difference in temperature

If the temperature difference between flow and return is greater than 45°C, the regulation locks. The lock is removed with a difference of less than 20°C. If the temperature difference between flow and return is less than –5°C, the regulation will lock immediately during central heating and 20 seconds after ignition during tapping.

6.2.6. Maximum temperature limitation

If the flow temperature goes above 105°C, when the burner is off, the regulation will lock with a continuous ‘H’ (hysteresis 5°C). If the flow temperature goes above 105°C, when the burner is on, the regulation will lock with a flashing ‘H’. Only a reset will remove the interlock. If the flow or return temperature goes above 97°C, the regulation will lock.

6.2.7. Flue gas temperature limitation

If, after switching the supply voltage on, a flue gas temperature of greater than –25°C is measured, the flue gas sensor is present. If a temperature below –25°C is measured afterwards, the regulation locks with the message flue gas sensor interruption (‘4’). If the flue gas temperature goes above 80°C, the burner is limited to low load. If the flue gas temperature goes above 90°C, the regulation locks with ‘A’. If the flue gas temperature goes below 70°C, both locks are removed. If the flue gas temperature goes above 95°C, the regulation locks with ‘A’.

6.2.8. Flow sensor protection

The difference between flow and return temperatures must be less than 20°C before each burner start. The difference between flow and return temperatures must be raised by 3°C within 10 seconds after each burner start. However, if the difference is less than the previous temperature difference, the burner is started again after 10 seconds. During this time, the capacity supplied by one of the hot water Combi-boilers during tapping is the desired capacity and in all other cases the initial capacity.

If the difference is not detected, the regulation locks with a ‘P’. This lock is removed when the flow temperature goes below 65°C and the minimum locking time (30 s) has elapsed. If this lock occurs more than three times within a heat demand, the regulation locks with ‘1’. If the difference between flow and return temperatures becomes less than –5°C during burning, the regulation locks.

Once per hour, if there is no heat demand, the difference between flow and return temperatures must be less than ± 5°C. If this is not the case, the pump will be switched on and a

check will be made for a maximum of 10 minutes to see whether the temperature difference goes to within ± 5°C.

6.2.9. Frost protection

When the flow temperature goes below 8°C (if there is no heat demand), the pump goes over to the central heating circuit and the display shows ‘o’. If the flow temperature goes below 3°C, the burner goes to low load. When the return temperature goes above 15°C, the frost protection is finished. When an external sensor is connected and the outside temperature goes below –4°C, the pump goes to central heating. This situation is removed at an outside temperature of –2 °C.

6.2.10. Monitoring the fan speed

When the measured fan speed deviates from the desired speed, this is masked in operation for 10 seconds. After these 10 seconds, the burner will go out of operation and the postventilation program will be performed. When the measured fan speed deviates from the desired speed during pre- or post-ventilation, the regulation locks. If this lock lasts for longer than 60 seconds, the regulation locks with ‘5’. When the measured fan speed goes above a maximum value during the rest state, the regulation locks. If this lock lasts for longer than 60 seconds, the regulation locks with ‘5’.

6.2.11. Glow plug protection

The glow plug protection counter is incremented at each ignition. This counter is decremented per minute. If this counter is too high, the burner demand is blocked.

Atmos Heating Systems Installation and user manual EN_FMT

CHAPTER 7. MAINTENANCE

High voltage! ! !

The wiring of the pump, the three-way valve, fan and wiring of the gas block can be under a voltage of 230 VAC.

Serial connection

A PC or Laptop can be connected for an extensive diagnosis and display of the functionality. The necessary cable (which contains an electrical isolation) and software can be ordered as options.

7.1. ANNUAL MAINTENANCE

After the first year, have a recognised installer or maintenance man inspect the unit. He can ascertain the maintenance deadline on the basis of the inspection and circumstances. A certified (SCIOS) installer should inspect the unit annually.

7.1.1. Checking the CO2 percentage on full load

The nominal value for natural gas at full load is 8.8% CO2.

The unit does not need to be cleaned if the measured CO2 percentage at full load is within

8.8% CO2 and 9.4% CO2.

7.1.2. Measuring the load on the unit

A load drop can be the consequence of a clogged flue gas channel or a clogged air intake channel. Check whether this is the case by measuring the load on the unit. First set the central heating capacity "P" to 100% in the menu. Let on the unit burn on chimney sweeper function at full load. Measure

the gas consumption. If the ascertained deviation in load is no more than 15% of the nominal value, the flue gases can be sufficiently exhausted and there is no clogging. At the end of the check, reset the central heating capacity "P" in the menu to its customer-

specific value.

7.1.3. Checking the condensation water drain

There is an opening for this purpose on the top of the vapour tray. First remove the rubber sealing plug; rinse the vapour tray and drain with clean tap water. When no more impurities are removed, the vapour tray is clean. Also clean the trap.

7.1.4. Ionisation probe

The ionisation probe is a part that wears. An insulating layer

can be formed in the flame at high temperature. This layer can be removed with fine sandpaper. Do not clean the ionisation probe with coarse sandpaper, because grooves in the surface of the pin will accelerate the formation of the layer.

Full load: Correct ionisation current between 6 µA DC to 13 µA DC. Low load: Correct ionisation current between 3µA DC to 13 µA DC.

Unplug the plug of the ionisation probe (low voltage). Remove the two screws from the ionisation clamp. Remove the ionisation probe from the cover and check the ionisation probe. The ionisation probe must be straight and clean (a slight deposit is normal), Clean or replace the ionisation probe.

7.1.5. Water pressure

Check the water pressure; top up and de-aerate as necessary. Press the ‘plus’ button in for at least 5 seconds to see the actual water pressure in bar on the display. Press briefly on the ‘min’ button to return to operational mode.

Atmos Heating Systems Installation and user manual EN_FMT

CHAPTER 8. MALFUNCTIONS

High voltage!

The wiring of the pump, the three-way valve, fan and wiring of the gas control can be under a voltage of 230 VAC.

8.1. Draining the unit

• On the central heating side: Switch the unit off and open the filling tap.

• On the HWS side: Switch the unit off. Shut the inlet combination off. Open a hot water tap and the protection device of the inlet combination.

When using the group of taps (see the accessory list), it is possible to only tap the unit. Proceed as follows:

- Switch the unit off.

- Close all taps under the unit.

- Close the inlet combination

- Open the filling tap under the unit.

- Open a hot water tap.

- Open the protection device in the unit and of the inlet combination.

8.2. No signal on the display

If there is no signal on the display, check if the mains voltage of 230 VAC is present on the unit. There must be voltage of 230 V on the live connection "L" and no voltage on the neutral connection "N". Check whether the on/off switch on the bottom of the unit is switched on.

Check the glass fuse on the printed circuit board Careful, high voltage! The fuse is placed on the printed circuit board in the 230 V circuit. So first disconnect the unit mains!

8.3. Fault code 'U/d or U/O' (alternating U with a status code will appear on the display)

This fault code occurs when the Live and Neutral are exchanged or when no Earth is present. Reverse the plug so that the Live is connected to Live and Neutral to Neutral.

8.4. Unit does not respond to central heating heat demand

Is the parameter for the type of unit correctly set in the menu?

• Parameter H = 1 is not active ( no heating).

• Parameter H = 4 is not active ( no heating).

• Parameter H = 5 is not active ( no heating).

Check for correct assembly and/or cable fracture of the wiring of the room thermostat (terminals 1 and 2) of the terminal block) and, if applicable, the external sensor (terminals 5 and

6) of the connection to the building management system (terminals 3 and 4).

8.7. Check function of gas control

Open the outlet pressure measurement nipple of the gas control

- connect the pressure meter to the outlet pressure measurement nipple

- measure the pressure (this must be zero)

- start the unit.

- the unit will now be rinsed at 1500 rpm

- next, the fan starts at the initial speed of 3000 rpm.

- the pressure meter will now indicate an underpressure of approximately 3 mbar

- when the gas control is opened, the zero pressure regulator will again make zero pressure.

- if not, then the gas control is not functioning.

8.8. Measuring the fan impedance

Check the resistance of the coil, the two outermost contacts on the fan motor.

The value that the multimeter shows must be between 115 and 120 Ohms at room temperature.

If the fan is defective, the drive on the drive on the Manager may also be damaged.

8.9. Fitting instructions for the pressure sensor

The seal is made with an “0”-ring. The pressure sensor must only be tightened slightly more than hand tight.

Atmos Heating Systems Installation and user manual EN_FMT

8.10. Fitting instructions for the safety valve

The safety valve must be tightened with a torque of 10 Nm.

8.11. Malfunction code 'F' (flashing)

After three failed attempts in a row, the unit will lock (flashing 'F'). This can have very different causes:

• no gas

• no ignition

• bad flame formation

• bad ionisation current

8.11.1. Gas control will not open (no voltage)

(Careful !!! 210 VDC).

If the gas control is not connected, the Manager will see this at the beginning of the heat demand as a malfunction and therefore lock. To measure the voltage on the gas control, the gas control must remain connected. During the starting period, the

gas control is connected to a voltage of 210 VDC.

8.11.2. Gas control will not open (gas inlet pressure too high)

The gas pressure in the gas pipe before the gas control is too high. The safety valves of the gas control cannot open with gas pressures of >60 mbar.

• open the inlet pressure measurement nipple of the gas control

• connect the pressure meter

• measure the gas pressure (10 - 50 mbar)

8.11.3. Gas control will not open (coils defective)

The electrical coils of the gas control are burnt out and the safety valves of the gas control will therefore not open.

• The two outermost contacts on the gas valve should be measured for resistance

• the value that the multimeter shows should be about

4.1 kOhm at ambient temperature.

8.11.4. Gas/air mixture is not correctly adjusted

see Chapter 4. : Adjustment full load and low load.

8.11.5. Check glow plug

The 230 volt glow plug is in order if the measured resistance at room temperature is about 1.0 - 1.4 kOhm.

• remove the connection of the glow plug (230 V)

• connect a multimeter

• measure the resistance

Replacing the glow plug

The glow plug is a resistance through which current is fed. As a result of the high temperature of the glow plug, the burner can be ignited. This makes the glow plug a part that wears. The average life of the glow plug is estimated at 8 years, depending on the

number of starts and on the variation of the mains voltage.

• remove plug from glow plug (230 V high voltage)

• remove glow plug from cover of unit

• replace glow plug

8.11.6. Check ionisation current

Direct measurement of the ionisation current using a multimeter ( µA DC).

When the unit burns on chimney sweeper function, the ionisation current can be read directly on the display.

• Ionisation current in full load is correct between 6 µA DC to 13 µA DC.

• Ionisation current in low load is right 3µA DC to 13 µA DC.

Insulating layer

With high temperature flame, an insulating layer can be formed on the probe. This layer can be simply removed with fine sandpaper. However, coarse grooves in the surface of the pin will accelerate new formation of the layer.

Atmos Heating Systems Installation and user manual EN_FMT

8.11.7. Inspection / cleaning / replacement of the ionisation probe

• unplug the plug of the ionisation probe (low voltage).

• remove the two screws from the ionisation clamp.

• remove the ionisation probe from the lid of the unit.

• check the ionisation probe.

• the ionisation probe must be straight and clean (a

slight deposit is normal).

• clean or replace the ionisation probe.

8.11.8. Ionisation probe or ionisation cable makes short circuit with earth

The negatively charged ions created by the burner form the ionisation current to earth. if there is short circuit to earth, the Manager cannot measure any current. Repair short circuit.

8.11.9. Boiler pump The boiler pump transports the system water through the primary heat exchanger for heating the system.

If the temperature difference between flow and return is greater than 30°C, the pump switches to a high speed

. When the temperature difference drops below 10°C again, the pump switches back to a low speed.

Electrical connection of pump with the boiler electronics.

N = neutral L = life The pump is earthed to the electronics as well.

Atmos Heating Systems Installation and user manual EN_FMT

USER MANUAL

General

The unit combines a maximum of comfort with an extremely easy operation. As the user, you need do no more than set the desired temperature on the room thermostat, no matter what time of the year.

Depending on how much you value optimum comfort and the lowest possible energy consumption, the following tips can help you make optimum use of your unit: To help limit the energy consumption, it is recommended to set the room thermostat to a lower temperature a few hours before going to bed. Turn all radiator taps fully open in the rooms that you want to heat. Shut the radiator taps off in the rooms where you do not want any heating.

Cleaning the unit

Regularly clean the outside of the unit with a soft, damp cloth. It is not necessary to shut the gas tap off or switch the mains off for this. Never use aggressive or flammable cleaning agents. Take note that the pipes can be at a high temperature.

Holidays

With long-term absence, for example in the holidays, it is recommended to leave the unit continually switched on. The reason is that the unit makes a number of checks every 24 hours. If frost can be excluded, set the room thermostat to a lower temperature. If frost cannot be excluded, set the room thermostat to a temperature of 12°C or higher. Although the unit has an internal frost protection, this does not protect the whole installation against freezing.

Brrrr, the central heating is not working

In the unlike event that the central heating has let you down, we have some tips for things that you can check and remedly yourself before an installer.

The central heating boiler is a fairly complicated item that is fitted with safety devices, which prevent a dangerous situation. There can be many reasons why the central heating is not working.

Electricity and gas

Is the connection of the green block in the green socket correct connected? Is the main switch on the unit in the right position? Or is the circuit to which the boiler is connected out of operation because the fuse has blown or the earth leakage switch has activated?

Is there an (unusual) interruption in the gas supply? Check by seeing whether a gas cooker in the kitchen is working. If it is now working, call the gas company. The gas flow can also be blocked because the gas filter of the boiler is contaminated; this is a problem for the service man. The unit also lets the pump regularly run outside the heating season to prevent it from sticking. If the mains supply outside is interrupted several times during the heating season, the pump can stick. Solution: turn the shaft of the pump a few times by hand (screwdriver).

Water and air

If the water pressure in the installation falls below a minimum level, the burner will be off. Solution: Top up with water. It is possible to read the water pressure directly from the display. Reading: Press the + button in for a minimum of 5 seconds. From the menu back to normal operation: Press the - button in briefly (or automatically after about 5 minutes). During filling, the unit must be connected to the mains and be switched on. Fully open all radiator taps. Connect the water supply to the filling connection of the installation. Open the tap to fill the system with water. When the water pressure is sufficient (> 1.3 bar), close the filling tap again. If there is air in the installation, the boiler can switch on, but the radiators remain cold. Follow the instructions from the manufacturer/installer for the venting of possible other elements of the heating installation, such as floor heating. Fully open all radiator taps. Vent the radiators after the pump is switched off. Open the air bleed cocks of the radiators one at a time. Use an air bleed key for this. As soon as water comes out of the air bleed cock, shut the cock off again. If the central heating boiler is at the highest point of the installation, air can collect in the boiler. This can cause a malfunction in the boiler. Also vent the internal tap pot (only with a Combi-unit).

Other causes

There must be heat demand from the room thermostat or other control, otherwise the boiler will not switch on. Set the thermostat to demand heat and check whether the boiler switches on; this can take a minute or so.

If there is little water circulation because too many radiator taps are closed, the boiler will not function or will function insufficiently. In this case, open more radiator taps or ask your installer to fit a bypass valve.

Atmos Heating Systems Installation and user manual EN_FMT

Display

Open the cover in front of the display to be able to read the codes.

The display consists of three 7-segment LED's + three decimal points and three pushbuttons.

The left 7-segment LED shows the status or the menu step.

The two right 7-segment LED's show the temperature, the pressure or the parameter value.

Furthermore, the display has three buttons:

• “Set/Reset button”

• “ - button”

• “ + button”

Reset button

This is to rest the unit, should it be locked by a malfunction. The user must use button. The installer should only be called when the same malfunction occurs repeatedly.

Abbreviated display indications

Display during normal operation (permanent) O

No heat demand, stand-by

Central heating heat demand, burner off

Central heating heat demand, burner on

P/C.

Central heating heat demand, low load water pressure

Central heating pump post-running

Heat HWS, burner off

Heat HWS, burner on

Heat external storage vessel, burner off

Heat external storage vessel, burner on

Frost protection, burner off

Frost protection, burner on

Display of blocks (permanent) 1

Flow sensor interrupted

Flow sensor short circuited

Return sensor interrupted

Return sensor short circuited

Flue gas sensor interrupted

Cold water sensor interrupted

Cold water sensor short circuited

Flue gas temperature > 80°C

Flow sensor > 105°C

Internal blocking fault

Pump test / Start function blocking / Water pressure

Burner Manager fault (can only be reset by switching voltage on/off)

Display of locks (flashing)

Flow/Return sensor fault

Too many restarts

Internal regulation fault / A/D conversion fault / external sensor fault

Fan fault

Gas valve fault

Flame detected with closed gas valve

Flue gas temperature > 95°C

Internal interlock fault

Flow sensor > 105°C with burner on

Too many ignition attempts

An interlock (flashing) can only be unlocked by pressing the set/reset button.

Atmos Heating Systems Installation and user manual EN_FMT

2004 Atmos Heating Systems Ltd.

All rights reserved. Nothing from this document may be duplicated and/or made public by means of printing, photocopy, microfilm or in any other way without prior written permission from the manufacturer. This also applies to the appropriate drawings and/or diagrams. The information supplied in this document is based on general data with regard to constructions, material characteristics and working methods known at the time of going to print. Therefore, we reserve the right to make changes without notification. For this reason, the instructions given serve only as a guideline for the installation, use and maintenance of the unit shown on the cover of this document.

This document is valid for the unit in its standard version. Therefore, the manufacturer cannot be held liable for any damage arising from specifications that deviate from the standard version of the unit delivered to you.

This document has been compiled with all possible care. However, the manufacturer cannot be held liable for any mistakes in this document or for any consequences.

Take the time to read this document carefully before installing or using the unit. Always keep this document near the unit.

Atmos Heating Systems Ltd. West March, London Road NN14SA Daventry

Tel: Fax:

Atmos Coopra Installation And User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual