Atmel ATA5577 User Manual

Atmel® offers a broad range of RFID devices for contactless read/write RF identifi cation systems, delivered
as die on wafer, die in tray, die on tape, micromodule, or complete transponder in a plastic package. Our
low-frequency IDIC

®

products (100 to 150 kHz) with different security levels are fl exible for all kinds of appli-

cations, easy to design-in and well-matched.

Multifunctional 363-Bit Read/Write

RFID IDIC ATA5577

RF IDENTIFICATION RFID

 Contactless 100 kHz to 150 kHz Read/Write

Identifi cation IC (IDIC)

 Version M1 Standard Pads
 Version M2 Mega Pads
 Backwards Compatible to e5550/51 in Most

Common Modes

 Backwards Compatible to T5557 and ATA5567
 On-Chip Capacitor 0 pF, 75 pF, 250 pF, or

330 pF, trimmed

 224-Bit User Memory (7 Blocks of 32 bits Each),

OTP Functionality

 64-Bit Unique ID
 32-Bit Analog Front End Register

 32-Bit Confi guration Register
 Binary Selectable Data Rate (RF/2 to RF/128)
 Modulation/Codings (FSK/PSK/ MAN/Bi-Phase/

NRZ)

 Password Mode
 Inverse Data Output
 32-Bit Password (Protection Against Unauthor-

ized Access)

 High Temperature Data Retention

(24h at 250ºC)

 Operating Range of –40ºC to +85ºC
 Fast Communication Protocols
 Self-Timing Downlink Protocols

Features

 Access Control ISO Cards, Key Fobs, and Coins
 Asset Management
 Animal Identifi cation

(Supporting ISO 11784/11785 – FDX-B)
– Livestock Tracking
– Pigeon Racing Tags

 Waste Management

ISO 11784/11785 (Non-Animal Mode)

 Laundry
 Manufacturing and Logistics

– Material Handling
– Recycling
– Cylinder Tracking

Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel
products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDITIONS OF SALES LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY
RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY
DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS AND PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE
USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this
document and reserves the right to make changes to specifi cations and products descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifi cally provided otherwise, Atmel
products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life.

The EEPROM is made up of two pages. Page 0
consists of 8 blocks, including confi guration reg­ister and 32-bit password. Page 1 includes three
blocks of 32 bits each and contains the 64-bit
unique ID and the analog front end register. Each
block can be protected against reprogramming via
a lock bit.

Applications

Ordering Information

Memory Mapping

Password Mode Support Tools

The memory of the ATA5577 can be protected
against unauthorized access. The password mode
provides write protection and – in combination with
the AOR feature – read protection.

© 2008 Atmel Corporation.

All rights reserved.

Atmel®, logo and combinations there-

of, IDIC®, and others are registered

trademarks or trademarks of Atmel

Corporation or its subsidiaries. Other

terms and product names may be

trademarks of others.

Rev.: 4612B-RFID-03/08/00M

Part Number

ATA5577M#

On-Chip

Cacity Value pF

ccc

Package

-xxx

Description

ATA5577M1
(Standard Pads)

000

1)

075

1)

250
330

DDB 6" Sawn Wafer on Foil with Ring, Thickness 150 µm (Approx. 6 mil)

DBB 6" Sawn Wafer on Foil with Ring and NiAu Bumps 25 µm, Thickness 150 µm

(Approx. 6 mil)

DDW

1)

6" Wafer, Thickness 280 µm (approx. 11 mil)

DDT

1)

Die in Waffl e Pack, Thickness 280 µm (Approx. 11 mil)

PAE

1)

NOA3 Micromodule (Lead-free)

ATA5577M2
(Mega Pads)

000

1)

075

1)

250
330

DBB 6" Sawn Wafer on Foil with Ring and Au Bumps 25 µm, Thickness 150 µm

(approx. 6 mil)

DDT

1)

Die in Waffl e Pack, Thickness 150 µm (Approx. 6 mil)

1)

On Request

Headquarters

Atmel Corporation

2325 Orchard Parkway
San Jose, CA 95131

USA

Tel: [phone]
Fax: [phone]

International

Atmel Asia

Room 1219
Chinachem Golden Plaza
77 Mody Road, Tsimshatsui
East Kowloon

Hong Kong

Tel: [phone]
Fax: [phone]

Atmel Europe

Le Krebs
8, Rue Jean-Pierre Timbaud
BP 309
78054 St Quentin-en­Yvelines Cedex

France

Tel: [phone]
Fax: [phone]

Atmel Japan

9F, Tonetsu Shinkawa Bldg.
1-24-8 Shinkawa
Chuo-ku, Tokyo 104-0033

Japan

Tel: [phone]
Fax: [phone]

Product Contact

Product Line

[e-mail]

Literature Requests

www.atmel.com/literature

Web Site

www.atmel.com

0 1..............................................................32

Page 1

L Analog Front End Option Setup Block 3
1 Traceabilty Data Block 2
1 Traceabilty Data Block 1
L Page 0 Confi guration Data Block 0

Page 0

L User Data or Password Block 7
L User Data Block 6
L User Data Block 5
L User Data Block 4
L User Data Block 3
L User Data Block 2
L User Data Block 1
L Confi guration Data Block 0

 Application Kits – ATAK2270, ATA2270-EK1
 Datasheet
 Application Notes
 Qual Packs