Atmel AT30TK175, AT30TSE002B, AT30TS75, AT30TS750, AT30TSE758 Hardware User's Manual

•

•

•

•

•

•

•

•

•

Power LED

Alarm status LEDs

Atmel Digital Temperature Sensors Evaluation Kit

Atmel AT30TK175 Starter Kit

Hardware User Guide

Features

Four digital temperature sensor devices:

• Atmel

• Atmel AT30TS75

• Atmel AT30TS750

• Atmel AT30TSE758

®

AT30TSE002B

Contents

One Atmel AT30TK175 adapter board
One Atmel AT88Microbase AVR® base module
6-inch USB cable
18-inch extension cable

Four event LEDs
Four alarm status LEDs:

• Critical, high, low, and normal

Software switchable VCC: 3.3V, 5.0V, and OFF
Power LED

Introduction

This starter kit utilizes the Atmel AT30TK175 adapter board to allow users to experiment and develop with the Atmel
AT30TSE002B, AT30TS75, AT30TS750, and AT30TSE758 digital t emperature sensors.

The AT30TK175 daughterboard interf ac es with the Atmel AT88Microbase board (included in the kit) to provide communication to a
PC via a USB interface, allowing designers to learn and experiment with the temperature sensor demonstration utility. In addition,
this kit supports a modular approach, enabling the AT30TK175 daughterb oar d to connect directly to an Atmel STK
development platform to easily add t em perature monitoring capabilities to applications.

®

series AVR

Figure 1. Atmel AT30TK175 adapter board

Digital temperature sensor and the
associated EVENT/ALERT LED

8745A–DTS–5/11

Atmel AT30TK175 Starter Kit Hardware User Guide

Atmel

Atmel

Atmel

Atmel

Serial EEPROM address

0x53 - -

0x52

Pins

10 9 8 7 6 5 4 3 2

1

Signal

VCC

GND

CRIT

LED

VCC

SEL

NORM

LED

VCC

EN

HIGH

LED

LOW

LED

SDA

SCL

1. Atmel AT30TK175STK Starter Kit

The AT30TK175 is sold with the AT88Microbase to form the Atmel AT30TK175STK starter kit. For additional information
on the AT88Microbase, see the “Atmel AT88Mi c robase Hardware User Guide.”

Figure 1-1. The Atmel AT30TK175 daughterboard with the Atmel AT88Microbase module

2. Board Configuration

Table 2-1. Seven-bit device address

Device

Temperature sensor address 0x1B 0x48 0x49 0x4A

2.2. 10-pin Interface Header

Table 2-1. I2C pins: SCL, SD

AT30TSE002B

AT30TS75

AT30TS750

AT30TSE758

2

8745A–DTS–5/11

Atmel AT30TK175 Starter Kit Hardware User Guide

LED

Critical

High

Low

Normal

Color

Red

Red

Yellow

Green

Active state

High

High

High

High

Control

High

Low

State

VCC_EN X

OFF

VCC_SEL X

3.3V (Default)

12

34

9

6

5

10

7

8

ATMEL

TSE002B

TSE758

TS750

TS75

Figure 2-2. 10-pin interface header orientation

Note: VCC_SEL and VCC_EN are board-level options that allow users to set the board VCC to 3.3V or 5.0V and

disable VCC with VCC_EN. These options are provided to allow the temperature sensor to be ev aluated with
both V

2.3. Alarm Status LEDs

Table 2-1. Alarm status LEDs

operating voltages and to evaluate the nonvolatile registers (se e S ection 2.3).

CC

2.4. V

Table 2-1. VCC enable and select pins

8745A–DTS–5/11

Enable and Select Pins

CC

VCC_EN X ON (Default)

VCC_SEL X 5.0V

3

Atmel AT30TK175 Starter Kit Hardware User Guide

3. References and Further Information

Schematics, Gerber files, bill of materials (BOM), and development and dem ons tration software are conveniently
downloadable from the Atmel website.

4. EVALUATION BOARD/KIT IMPORTANT NOTICE

This evaluation board/kit is intended for ENGINEERING, DEVELOPMENT, DEMONSTRATION or EVALUATION
PURPOSE ONLY. It is not a finished product and may not (yet) comply with some or any technical or l egal
requirements that are applica bl e to finished products, including, without limitations, directiv es regarding electromagnetic
compatibility, recycling (WEEE), FCC, CE or UL (except as may be otherwise noted on the board/kit). Atmel® supplied
this board/kit “AS IS,” without any warranties, with all faults, at the buyer’s and further users’ sole risk. The user
assumes all responsibly and liabili ty for proper and safe handling of goods. Further, the user indemnifies Atmel from
claims arising from the handling or use of goods. Due to open construction of the product, it is the user’s responsibil ity to
take any and all appropriate precautions with regard to electrostatic discharge and any other technical or legal concerns.

EXCEPT TO THE EXTENT OF INDEMNITY SET FORTH ABOVE, NEITHER USER NOR ATMEL SHALL BE LIABLE
TO EACH OTHER FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.

No license is granted under any patent right or other intellectual property right of Atmel covering or relating to any
machine, process, or combination in which such Atmel product or services m ight be or are used.

Mailing Address: Atmel Corporation

2325 Orchard Parkway
San Jose, CA 95131

4

8745A–DTS–5/11

Atmel Corporation

Atmel Asia Limited

Atmel Munich GmbH

Atmel Japan

warranted for use as components in applications intended to support or sustain life.

2325 Orchard Parkway
San Jose, CA 95131
USA

Tel: [phone]
Fax: [phone]

www.atmel.com

Unit 01-5 & 16, 19F
BEA Tower, Millennium City 5
418 Kwun Tong Road
Kwun Tong, Kowloon
HONG KONG

Tel: [phone]
Fax: [phone]

© 2011 Atmel Corporation. All rights reserved. / Rev.: 8745A–DTS–5/11

®

, logo and combinations thereof, and others are registered trademarks or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be

Atmel
trademarks of others.

Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of
Atmel products. EXCEPT AS SET FORTH IN THE ATMEL TERMS AND CONDITIONS OF SALES LOCATED ON THE ATMEL WEBSITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR
STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT
SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS AND PROFITS, BUSINESS
INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no
representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and products descriptions at any time without notice. Atmel does not make
any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel products are not intended, authorized, or

Business Campus
Parkring 4
D-85748 Garching b. Munich
GERMANY

Tel: [phone]
Fax: [phone]

9F, Tonetsu Shinkawa Bldg.
1-24-8 Shinkawa
Chuo-ku, Tokyo 104-0033
JAPAN

Tel: [phone]
Fax: [phone]

Mouser Electronics

Authorized Distributor

Click to View Pricing, Inventory, Delivery & Lifecycle Information:

Atmel:
AT30TK175STK