Atlona AT-PRO2HD88M User Manual
Atlona HDMI 8 by 8 Matrix Switcher
over CAT5e/6/7
AT-PRO2HD88M
atlona.com
User Manual
Revision 2: Firmware 1.1.16
Toll free: 1-877-536-3976
Local: 1-408-962-0515
Table of Contents
1. Introduction .................................................................................... 3
2. Package Contents .................................................................................... 3
3. Features .................................................................................... 3
4. Before You Start .................................................................................... 4
5. Specifications .................................................................................... 4
6. Remote Control .................................................................................... 4
7. Panel Descriptions
a. Front Panel .................................................................................... 5
b. Rear Panel .................................................................................... 6
8. Connection and Installation
a. 3rd Party Control .................................................................................... 7
b. IR Remote Control .................................................................................... 8
c. Matrix I/O Control .................................................................................... 9
d. EDID Set Up .................................................................................... 10
e. Matrix Settings .................................................................................... 11
9. RS-232
a. Connection .................................................................................... 12
b. Command .................................................................................... 12
c. Set Up .................................................................................... 13
d. Baud Rate ............................................................................... 13-14
10. Resetting and Updating .................................................................................... 15
11. Safety Information .................................................................................... 16
12. Warranty .................................................................................... 17
13. Atlona Product Registration .................................................................................... 18
Revision 2 (7/30/12):
Firmware Version 1.1.16
New RS-232 code Page 12
atlona.com
2
Toll free: 1-877-536-3976
Local: 1-408-962-0515
Introduction
Extend HDMI and DVI (with HDMI to DVI adapter ex. AT-14040) sources up to 330ft at 1080p or
1920x1200. The Atlona HDMI 8 by 8 Matrix Switcher over CAT5e/6/7 allows for effortless control
of up to 16 devices through IR remote control, RS-232, 3rd party IR controllers and the front panel.
With stereo audio embedding combine stereo audio with DVI signals over one CAT5e/6/7 cable. To
ensure all audio passes through the 8 by 8 Matrix Switcher supports all Lossy and Lossless formats
of Dolby and DTS. The AT-PRO2HD88M delivers the best quality available with pass through of up
to 1080p, 1920x1200, 3D, and Dolby TrueHD and DTS-HD Master audio signals.
Package Contents
• 1 x 8x8 Matrix Switcher over CAT5e/6/7
• 1 x IR Receiver
• 9 x IR Emitter
• 2 x 24V/6.25A DC adaptor
• 2 x Power Cord
• 1 x Remote Control
• 1 x User Manual
IR Receiver
Power Cord
IR Emitter
Features
• HDBaseT allows IR, RS-232, audio and visual signals to pass over a single CAT5e/6/7 cable.
• IR ports for zone dedicated control through IR remote control and 3rd party IR controllers.
• 8 programmable I/O memories, save up to 8 routes for faster switching to the most commonly
used configurations.
• EDID learning function for up to 8 video display EDIDs.
• Multiple control interfaces such as RS-232, IR, and the front panel.
• Dolby TrueHD and DTS-HD Master Audio pass through HDMI output interface.
• Compatible with DVI/D (with DVI/D to HDMI adapter such as AT14040), allowing DVI/D source
signal to be passed to displays.
• Audio embedding enabled with DVI/D sources. The built in 3.5mm audio import port allows DVI/D
audio to be passed through with the CAT5e/6/7 connection to HDMI displays.
• Optional receiver module AT-PRO2HDREC-DA de-embeds audio and sends it to an amp through
the S/PDIF port.
• HDCP compliant
atlona.com
3
Toll free: 1-877-536-3976
Local: 1-408-962-0515
Before You Start
• Make sure when connecting the CAT5e/6/7 cables a 568B termination method is used.
• Avoid using patch panels and wall plates during initial set up and testing of the matrix switcher.
• Make sure the matrix is connected to a component surge suppressor and line conditioner.
Note: Atlona’s warranty does not cover damage due to electrical disturbances. A component surge
suppressor and line conditioner are highly suggested especially in areas with electrical storms.
• Be sure you’re using a mono to mono (2 conductor) 3.5mm IR cable (i.e. AT-MINIMONO6 -
available to purchase at Atlona.com) when using IR output control from 3rd party controllers,
stereo (3 conductor) 3.5mm cables are not compatible.
Specifications
Bandwidth frequency 6.75 Gbps
Input Ports 8 x HDMI (Female Type)
9 x IR 3.5mm
1 x Firmware update
8 x 3.5mm Stereo Audio
Output Ports 8 x CAT 5e/6/7
1 x RS-232
9 x IR 3.5mm
Resolution outputs Video: up to 1080p@60Hz
Vesa: up to 1920x1200
Dimensions (HxWxD) 6.93x18.98x14.27 (inch) or 176x482x362.5 (mm)
Weight 21.61lbs or 9.8 kg
Temperature -4°F to 158°F or -20°C to 70°C
Power consumption 60W
Remote Control
Output selection. Numbers correspond with the CAT5e/6/7
category cable outputs on the matrix. The same remote is used
for the AT-PRO2HD88M as the AT-PRO2HD1616M. For ATPRO2HD88M only 8 I/O buttons will be functional.
Arrow buttons are not functional for this product.
Input selection. Numbers correspond with the HDMI inputs on
the matrix. The same remote is used for the AT-PRO2HD88M as
the AT-PRO2HD1616M. For AT-PRO2HD88M only 8 I/O buttons
will be functional.
atlona.com
4
Toll free: 1-877-536-3976
Local: 1-408-962-0515
Panel Description
Front Panel
2
3
5
1
4
6
7
a
c
b
8
e
d
f
g
1. Power Indicators. Red LED will light up when using main or backup power supply.
2. IR Receiver Window. Receives the signal from the included IR Remote Control or a 3rd party IR
Controller.
3. Power Indicator. The light will illuminate red when the Matrix is in standby mode or green when
the matrix is on.
4. Power Button. Cycles the power between on or off (standby) mode.
5. Enter Button. Use to view current status for inputs and outputs or to confirm a command.
6. Cancel Button. Within the functions menu use to go back one screen or to the home screen.
Note: You cannot power off or change functions unless you go to the home screen.
7. Function Button. Allows you to select command options.
a. Lock: Locks all the panel keys so nothing can be altered until unlocked.
b. All: Save a single input to all the outputs with this function.
c. Default: Mirrors all inputs to corresponding outputs. (i.e. 1 to 1, 2 to 2, 3 to 3, etc.)
d. Save: Save the current input and output route to memory. Up to 8 programmable
memories.
e. Recall: Load the input and output routes that you have previously saved.
f. EDID: This function allows for individual output properties to be saved, altered or loaded
to inputs. EDID has 8 memory settings to save to for easy loading later.
Note: Default setting for EDID is the highest common HD resolution of all connected
devices. (i.e. if you have resolutions ranging 720p, 1080i, and 1080p then 720p would be
the default resolution for all connected displays.)
g. Firmware: This function option will display the current firmware the Matrix has installed.
8. Number buttons. Use these buttons to select input and output paths or use with the function
button to change multiple matrix settings.
atlona.com
5
Toll free: 1-877-536-3976
Local: 1-408-962-0515
Back Panel
1
2
6
3
4
5
11
1. Matrix IR IN - Used to control matrix I/O switching from a 3rd party IR controller.
2. Matrix IR Out - Global output, combines IR for all discrete IR output ports.
3. Firmware Update - Type B USB Port used for updating the matrix firmware only
4. RS-232 - Connect to this port for control from a computer or 3rd party controller.
5. Main Power - Plug included 24V/6.25A DC adaptor to power the matrix switcher
6. Audio Input Ports - 3.5mm stereo audio port enabled only when a DVI/D adaptor is connected,
disabled when HDMI cable is connected.
7. HDMI Input Ports - Connect HDMI sources into these ports, such as DVD players, Blu-ray players,
computers, etc.
8. IR 3.5mm mono In ports - Used in conjunction with 3rd IR party controller to extend IR control
commands to video displays over CAT5e/6/7.
Note: Be sure you’re using a mono to mono 3.5mm IR cable (i.e. AT-MINIMONO6) for 3rd
party control boxes, stereo 3.5mm cables are not compatible.
9. IR Out ports - Sends IR signal to sources through a 3.5mm mono IR emitter
10. CAT5e/6/7 Output ports - Extends video and bidirectional RS-232, IR, and audio signals through
a single CAT5e/6/7 cable.
11. Backup Power - Redundant power supply in case the main power supply fails. Includes second
24V/6.25A DC adaptor.
7
8
9
10
atlona.com
6
Toll free: 1-877-536-3976
Local: 1-408-962-0515
Loading...