Atlona UK HDBaseT
Wall Plate Receivers
AT-HDWP-UK, AT-HDWP-IR-UK
AT-HDWP-UK
AT-HDWP-IR-UK
User Manual
atlona.com
Toll free: 1-877-536-3976
Local: 1-408-962-0515
Table of Contents
1. Introduction ................................................................................... 3
2. Package Contents ................................................................................... 3
3. Features ................................................................................... 3
4. Panel Descriptions ................................................................................... 4
5. Electrical Box ................................................................................... 4
6. Wall plate installation ................................................................................... 5-6
7. Captive Screw ................................................................................... 7
8. Connection ................................................................................... 8-10
9. Specifications ................................................................................... 11
10. Safety Information ................................................................................... 12
11. Warranty ................................................................................... 13-14
12. Atlona Product Registration ................................................................................... 14
atlona.com
2
Toll free: 1-877-536-3976
Local: 1-408-962-0515
Introduction
Extend uninterrupted 1080p signal up to 230ft (70m) with the Atlona UK HDBaseT Wall Plate
Receivers. With pass through support of 4Kx2K, 1920x1200, lossy & lossless audio, and
bi-directional IR* signals over a single category cable, the HD extenders provide affordable, high
quality, solutions for your audio/video and IR* control needs.
Package Contents
• 1 x AT-HDWP-UK Receiver
• 1 x Male Captive Screw Connector (5 pin - HDWP-IR-UK only)
• 2 x 30mm screws for the electrical box
• 4 x 4mm screws for the face plate
• 1 x IR Emitter (HDWP-IR-UK only)
• 1 x IR Receiver (HDWP-IR-UK only)
• 1 x User Manual
Features
• Extends IR* and audio/visual content up to 230ft @ 1080p over a single category cable
• Supports 4Kx2K pass through up to 130ft
• Built to be hidden, allowing the receiver to be hidden behind a wall mounted TV
• USB updating for easy, in the field, firmware updates
• Captive screw IR* I/O ports for emitting and receiving IR control signals for use with IR remote
controls and 3rd party control boxes (HDWP-IR only)
• PoCc (Power over Category cable) feature removes the need for a power supply when paired with
an Atlona compatible HDBaseT transmitter, matrix, or distribution amplifier.
(Ex. HDTX, HDTX-IR, PRO3HD44M, AT-HDCAT-4, etc.)
• Lossy and lossless multi-channel audio formats pass through (including Dolby TrueHD and
DTS-HD Master Audio)
• Full 3D pass through
• HDCP compliant
* IR extender version only
atlona.com
3
Toll free: 1-877-536-3976
Local: 1-408-962-0515
Panel Description
1
-
IR
2
+
3
IR IN
PWR
LINK
AT-HDWP-IR-UK
4
IR OUT
HDMI OUT
FW
5 6
1. IR IN Port: Connect the IR receiver to this port.*
2. IR OUT Port: Connect the IR Emitter to this port.*
3. HDMI OUT Port: Connect to HDMI display.
4. Yellow Link LED: Signal Indicator for the CAT5e/6/7 OUT port. LED will remain solid, unless there
is an issue with the cable or signal, then it will blink.
Green Power LED: Power indicator. If plugged in light will remain solid. If LED starts blinking
power is intermittent or there is a problem with the cable. If LED is off, no power is passing to
the receiver (check your outlet or the power cable for the transmitter).
5. Firmware Update Port: Use a Mini USB to USB A cable to connect to a Windows computer for
updating.
6. CAT5e/6/7 IN Port: Connect a category cable from a compatible transmitter to this port.
*For IR products only
Electrical Box
With so many electrical back boxes it is hard to know which to purchase with any wall plate. For
convenience Atlona has compiled recommended electrical boxes to use with the HDWP-UK and
HDWP-IR-UK.
For 9.5mm up to 12.5mm walls: Red/Grey 1 Gang box or mud ring is best
For 12.5mm walls: Appleby 1 gang box or mud ring is best
Note: All electrical back boxes must be at least 30mm deep.
atlona.com
4
Toll free: 1-877-536-3976
Local: 1-408-962-0515
Wall Plate Installation
A
There are four pieces that will need to be interconnected in order for the AT-HDWP-IR-UK to be
installed in the wall. The electrical box (picture A), the HDBaseT module (picture B), the face plate
(picture C) and the CAT cable.
B
C
First, remove the face plate from the HDBaseT module. To do this, remove the four 4mm screws on
the sides (as pictured above).
Note: Avoid contact with the PCB board (see picture B) in the HDBaseT module, electrostatic
discharge (ESD) may damage sensitive chips.
Next, route the CAT cable through the electrical box (as seen above) and connect it to the back of
the HDBaseT module (see picture on top of page 6).
atlona.com
5
Toll free: 1-877-536-3976
Local: 1-408-962-0515
Loading...