Atlona AT-HDVS-RX User Manual

Atlona HDBaseT to HDMI

Receiver/Scaler

with Audio De-Embedding

AT-HDVS-RX

atlona.com

User Manual

Toll free: 1-877-536-3976

Local: 1-408-962-0515

Table of Contents

1. Introduction .................................................................................. 3

2. Package Contents .................................................................................. 3

3. Features .................................................................................. 3

4. Panel Descriptions

a. Front Panel .................................................................................. 4

b. Rear Panel .................................................................................. 4

5. OSD Menu .................................................................................. 5-6

6. RS-232 & Software .................................................................................. 7-11

7. Connection and Installation .................................................................................. 12

8. Specifications .................................................................................. 13

9. Safety Information .................................................................................. 14

10. Warranty .................................................................................. 15-16

11. Atlona Product Registration .................................................................................. 16

Firmware 1.1.0 (5/1/14):
Pages 3, 5-10 Added EDID configuration for inputs
Auto ON/OFF for display when HDMI source is detected
HDCP reporting On/Off/Auto mode added
New GUI software

Firmware 2.1.0

Apple and Windows 8.X updating

atlona.com

2

Toll free: 1-877-536-3976

Local: 1-408-962-0515

Introduction

Atlona HDVS receiver was designed to smooth the transition from analog to digital displays in
schools and businesses, allowing advanced HDMI display devices to be used with the many VGA
computers still in use. Many displays don’t support the resolutions and refresh rates typical of
VGA sources. In addition, the HDVS-RX is compatible with Atlona PoCc switchers and distribution
amplifiers with HDBaseT outputs and is a good solution when scaling is required for a specific
display.

When used with a matching HDVS-TX or HDVS-TX-WP, projector control is enabled. HDBaseT and
power over category cable (PoCc) allow signal and power over a single category cable, with RS-232
control capability.

Package Contents

• 1 x AT-HDVS-RX

• 1 x 3.5mm to D-sub adapter

• 2 x Captive screw female connector (5 pin: audio, 2 pin: power)

• 1 x 24V DC captive screw power adapter

• 1 x User manual

Features

• Scales incoming signals at a variety of common resolutions up to 1080p or 1920x1200

• Complete control of video brightness, contrast, saturation, hue, and more

• Extends common resolutions up to 1080p or 1920x1200 to distances as long as 230ft (70
meters)*

• Front panel on-screen menu control for ease of use

• Set preferred input resolution to match display requirements

• 2 channel balanced analog audio output to an amplifier (Ex. AT-PA100-G2)

• PoCc (Power over Category cable) sends power to compatible transmitters
ex. AT-HDVS-TX-WP, AT-HDVS-TX, or AT-HDTX-WP

• Ability to switch HDCP reporting between compliant, noncompliant, and auto

• Firmware upgradable for easy field service through USB

Note: For full functionality and features, ensure the transmitter and receiver are using compatible firmware

Transmitter firmware V 1.0.1 Compatible Not Compatible Not Compatible

Transmitter firmware V 1.1.0 Not Compatible Compatible Compatible

Transmitter firmware V 2.1.0 Not Compatible Compatible Compatible

atlona.com

Receiver firmware V 1.0.1 Receiver firmware V 1.1.0 Receiver firmware V 2.1.0

GUI Version 1.4 1.1.0 1.1.0

Toll free: 1-877-536-3976

3

Local: 1-408-962-0515

-

+

CAT5e/6/7 IN FIRMWARE DC 24V

Panel Description

Front Panel

+-+

-

POWER

LINK

HDMI OUT

L

AUDIO OUT

R

RS232

2

3 6

41

MENU

5

+

-

1. HDMI OUT: Connect to display

2. AUDIO OUT: Connect to amplifier (ex. AT-PA100-G2)

3. RS-232: Connect to PC or control system to program RS-232 control then connect to a
display for on / off command control

4. Status LEDs
POWER LED: Illuminates when receiving power
LINK LED: Illuminates when HDBaseT link is functioning properly

5. MENU button: Use to enter, exit, and select within the on-screen display OSD menu

6. Navigation buttons: Navigate through OSD menu or use to set output resolutions
“Menu” and “-” : Set output resolution to 720p@50Hz
“-” and “+” : Factory resets receiver and sets output resolution to 720p@60Hz

Note: Pressing the “+” button while the OSD menu is closed and a VGA source is selected will cause the
video to auto adjust

Back Panel

1. CAT5e/6/7 IN: Connect HDBaseT source here

2. FIRMWARE: Connect to a PC using a mini USB to USB for firmware updating

3. DC 24V: Connect included 24V DC adapter here to power HDVS-RX and compatible transmitters

atlona.com

+

-

CAT5e/6/7 IN FIRMWARE DC 24V

1

2

3

4

Toll free: 1-877-536-3976

Local: 1-408-962-0515

OSD Menu

Menu Option Sub-Menu Option Adjust

Input Select VGA

HDMI

HDMI 2 (AT-HDVS-TX)

Menu Back

Input Resolution 800x600 1280x800 1920x1200

1024x768 1366x768

1280x720 1920x1080

Output Resolution 1024x768 720p59.94 1080p60

1280x800 720p60 Native

1280x1024 1080i50 Menu Back

1366x768 1080i59.94

1400x1050 1080i60

1600x1200 1080p23.98

1680x1050 1080p24

1920x1200 1080p25

720p35 1080p29.97

720p29.97 1080p30

720p30 1080p50

720p50 1080p59.94

VGA Adjust

Picture Adjust Brightness 0 to 100

Contrast 0 to 100

Saturation 0 to 100

Hue 0 to 100

Sharpness 0 to 100

Picture Reset

Menu Back

Aspect Full Full Screen

16:9 TV

16:10 TV

4:3 TV

Keep Ratio

Menu Back

Overscan Enable Yes or No

H Size % 0 to 50%

V Size % 0 to 50%

Menu Back

Audio Audio On/Off On or Off (mute)

HDMI Audio On or Off

L/R Audio On or Off

Menu Back

atlona.com

5

Toll free: 1-877-536-3976

Local: 1-408-962-0515

Menu Option Sub-Menu Option Adjust

OSD Position Left-Top, Right-Top, Right-Bottom, Left-Bottom, Center

Transparency 0 (transparent) to 15 (solid)

Info. Timer 5 to 100 seconds

Menu Timer 5 to 100 seconds

Info. Display Always On, Auto, or Always Off

Background Grey, Cyan, Magenta, or Yellow

Menu Back

Others In Auto Switch On or Off

Display HDCP Compliant, Noncompliant, Auto

Mirror-V On or Off

ASP Background Grey, Black

Display Mode DispSW AVon, DispSW AVSW, AV SW, Always On

Disp. Key Lock 0 to 15 seconds

Auto Disp. On On or Off

Auto Disp. Off On or Off

ProJSW Mode 5 to 300 (increases by 5)

Standby (min.) 0 to 15

Menu Back

Information Source

Name
Product

Sink
Model
Native 1
Native 2

F/W TX: RX:
Menu Back

System Reset No

Yes

Menu Back

Menu Exit

Note: Display Mode does a variety of changes, see below

DispSW AVon - Display switches on/off, source audio/video signal always on
DispSW AVSW - Display switches on/off, source audio/video signal switches on/off
AV SW - Display is always on, source audio/video signal switches on/off
Always On - Default, no function

Note: Must be in DispSW AVon or DispSW AVSW for RS-232 display control to work

ProJSW Mode: Used with a projector whose lamp cannot be turned on for up to 5 minutes after
being shut off. Keeps control in same state as projector. Match settings with lamp delay on
projector in 5 to 300 seconds. The LED will blink for the full amount of the delay time (ex. 40
seconds).

Standby (min.): Adjusts period of time before scaler goes into standby following loss of signal.
Default is 0 minutes (standby off)

Note: Standby must be active for Display Off to work - Standby time will set display off time as well.

atlona.com

6

Toll free: 1-877-536-3976

Local: 1-408-962-0515

RS-232

Connection

RS-232 is connected through a 9-pin female DB connector. Only pins 2, 3, and 5 are terminated.

No. Pin Function

1 ---- Not used

5

4

9 8 7

Set up and Control Software

Set up and control software can be found on the AT-HDVS-RX webpage on atlona.com.

URL: http://www.atlona.com/HDVS-RX.html (software found under the “Downloads” tab)

2

3

1

6

2 Rx Receiver
3 Tx Transmit
4 ---- Not used
5 Gnd Ground
6 ---- Not used
7 ---- Not used
8 ---- Not used
9 ---- Not used

Set Up

1. Connect the receiver to a PC using a 9 pin serial to USB adapter

Note: Receiver must be disconnected from the display for RS-232 set up

2. Go to the device manager folder (see picture A) on your computer

3. Find the receiver COM port.

Note: If unsure which COM port is connected, unplug the USB cable and plug it back in. It will
disappear and reappear on the COM port list.

4. Open software, select the correct COM port, and press connect. (see picture B)

Note: You can test the connection by pressing READ

A

Note: If you are having trouble reading or controlling the HDVS try using a null modem adapter

atlona.com

B

Toll free: 1-877-536-3976

7

Local: 1-408-962-0515

1

7

2

3

4

5

6

8

9

10

11

12

13

14

1. Control select - switch between projector on/off controls and the HDVS-RX controls

2. Input source selection - choose between the HDMI and VGA ports

3. Input resolution - switch between the preferred resolutions
800x600, 1024x768, 1280x720, 1280x800, 1366x768, 1920x1080, 1920x1200

4. Output resolution - switch between the output resolutions and native resolution
VESA: 1024x768, 1280x800, 1280x1024, 1366x768, 1400x1050, 1600x1200,
1680x1050, 1920x1200
Video: 720p@30/50/59.94/60, 1080i@50/59.95/60, 1080p@24/25/29.97/30/50/59.94/60

5. Aspect - changes the HDVS’s ratio to work with the connected display

6. VGA auto adjust and Overscan - Adjust the picture positioning on the display

Note: It is recommended to set the HDVS to 0% for PCs and Overscan for BluRay players

7. System reset - Sets the HDVS back to the default settings

Note: Saving is recommended before using the system reset

8. Read - Displays the current HDVS settings

9. Display mode - Display on/off button operation selection for the HDVS-TX/TX-WP

DispSW AVon - Display switches on/off, source audio/video signal always on (default)

DispSW AVSW - Display switches on/off, source audio/video signal switches on/off
AV SW - Display is always on, source audio/video signal switches on/off
Always On - No function

Note: Must be in DispSW AVon or DispSW AVSW for RS-232 display control to work

10. Display on/off - Video signal to display is turned on/off

11. Display HDCP - set HDCP reporting to Compliant, Noncompliant, or Auto

Compliant - Tells the source it is connected to an HDCP compliant device

Noncompliant - Tells the source it is connected to an HDCP noncompliant device
Auto - Will report compliant or noncompliant to the source depending on what the display
reports.

12. Standby (min.) - select how long it takes before the RX goes into standby

Standby (min): Adjusts period of time before the scaler goes into standby following loss of

signal. Default has standby mode off

Note: Standby must be active for Display Off to work - Standby time will set display off time
as well.

13. Audio on/off - use to turn audio on and off

14. FW - Press the “GET” button to display the current firmware of the RX and TX units

Note: See the chart on page 3 to verify compatibility

atlona.com

8

Toll free: 1-877-536-3976

Local: 1-408-962-0515

1

2

3

1. Picture settings - Set the brightness, contrast, saturation, sharpness, and hue for the output
Note: Calibrate the display before using the HDVS-RX picture settings to adjust the output

2. Read - Press to populate the HDVS settings

3. Reset - Resets the picture to factory default settings

1

2

3

4

5

6

1. Save: Allows a display’s RS-232 settings to be saved to the PC for easy set up in the future
Load: A previously saved display’s settings from your PC

2. RS-232 port - Set to display’s port settings
(See display’s manual for the recommended device settings)

3. Select between text (ASCII) and hex commands input for display on and off

4. Type commands for display on and display off in these fields

5. Send: Once the information is entered, press send to transmit command to RX to set up control
Read: Verifies commands are correctly stored on the HDVS-RX

6. Use these buttons to add a carriage return at the end of the command

Note: Carriage return will show a square and circle to confirm the carriage return (see picture A)
Note: When switching back to text, any non-ASCII HEX will display as bullets (see picture B)

A B

atlona.com

9

Toll free: 1-877-536-3976

Local: 1-408-962-0515

1. Auto display on - select on or off
On: turns the display on when a source is detected

2. Auto display off - select on or off
On: turns the display off when no signal has been detected for the amount of time selected
under standby mode

3. Read - displays the current settings

4. ProjSW mode (sec.) - Locks the front panel keys (after display off command) for the amount of
time specified. Sets time from 0 to 300 seconds (in increments of 5)

1

2

3

4

Commands

The command codes are case sensitive, do not change capitalization, spacing, or lettering.

Command Parameters Description

WP_DisplaySet[a,b,c,d]$
WP_DisplaySet[?]$

WP_DisplayOn[a,b]$
WP_DisplayOn[?]$

WP_DisplayOff[a,b]$
WP_DisplayOff[?]$

WP_IdentifyTx[a]$ [a] ? Identify Tx model; reply TX=AT-HDVS-

WP_Input[a]$ [a] ? , Hdmi1 , Hdmi2 , Vga Select input source

WP_Input[a]$ [a] ? , Hdmi , Vga Select input source

WP_InputPrefer[a]$ [a] ?, 0 , 1 , 2 ...* Select preferred input resolution

WP_Display[a]$ [a] ? , On , Off Display On/Off control

WP_DisplayMode[a]$ [a] ? , DispSWAVOn , DispSWAVSW , AVSW ,

WP_Aspect[a]$ [a] ? , Full , 16:9 , 16:10 , 4:3 , Keep Select output aspect ratio

WP_AutoSwitch[a]$ [a] ? , On, Off Input Auto Switch enable/disable

[a] baud rate: 2400 , 9600 , 19200 , 38400 ,
56000 , 57600 , 115200

[b] data bit: 5 , 6 , 7 , 8
[c] parity: N (None) , O (Odd) , E (Even) , M

(Mark) , S (Space)

[d] stop bit: 1 , 1.5 , 2

[a] command length.

carriage return is computed, if it has one.
Max. command length is 50
[b]command string.
Include carriage return, if it has one.
Supports multi-command in a command string.
Supports delay-command COMMA
(a comma=5 sec)

[a] command length.
carriage return is computed, if it has one.
Max. command length is 50
[b]command string.
Include carriage return, if it has one
Supports multi-command in a command string.
Supports delay-command COMMA
(a comma=5 sec)

AlwaysOn

Set projector’s RS-232 port

Set projector’s Display On command

Set projector’s Display Off command

TX, TXWP=AT-HDVS-TX-WP

Set display mode

Input Resolutions: 0 = 800x600, 1 = 1024x768, 2 = 1280x720, 3 = 1280x800,
4 = 1366x768, 5 = 1920x1080, 6 = 1920x1200

atlona.com

10

Toll free: 1-877-536-3976

Local: 1-408-962-0515

Commands cont.

WP_AutoDispOn[a]$ [a] ? , On , Off Set auto [Dispaly On] enable/disable

WP_AutoDispOff[a]$ [a] ? , On , Off Set auto [Dispaly Off] enable/disable

WP_HdcpInput[a]$ [a] ? , HDCP , NotHDCP, Auto HDCP input mode

WP_VgaAuto[a]$ [a] Go Run VGA source auto-adjust

WP_VgaClock[a]$ [a] ? , Normal , Inverse Set VGA ADC clock polarity

WP_Info[a]$ [a] ? Get RX firmware version

WP_InfoTx[a]$ [a] ? Get TX / TX-WP firmware version

WP_Output[a]$ [a] ? , 0 , 1 , 2 ... (map osd menu Output list) Select output resolution

WP_OverscanEn[a]$ [a] ? , Yes , No Set overscan enable/disable

WP_OverscanH[a]$ [a] ? , 0 ~ 50 Set overscan H size (%)

WP_OverscanV[a]$ [a] ? , 0 ~ 50 Set overscan V size (%)

WP_AudioEn[a]$ [a] ? , On , Off Set audio out On/Off

WP_AudioHdmi[a]$ [a] ? , On , Off Set hdmi audio out On/Off

WP_AudioLR[a]$ [a] ? , On , Off Set analog L/R audio out On/Off

WP_SystemRst[a]$ [a] Go Run system reset

WP_PictureBri[a]$ [a] ? , + , - , 0 ~ 100 Set picture brightness

WP_PictureCon[a]$ [a] ? , + , - , 0 ~ 100 Set picture contrast

WP_PictureSat[a]$ [a] ? , + , - , 0 ~ 100 Set picture saturation

WP_PictureHue[a]$ [a] ? , + , - , 0 ~ 100 Set picture hue

WP_PictureSha[a]$ [a] ? , + , - , 0 ~ 100 Set picture sharpness

WP_PictureRst[a]$ [a] Go Run picture reset

WP_ProjSW[a]$ [a] ? , 0 , 5 , 10 , ~ 300

WP_Standby[a]$ [a] ? , 0 ~ 10 Standby timer in minute

]$ Abort command, Feedback is

COMMAND FAIL

Note:

1. Each command and feedback is terminated with a carriage return.

2. Spaces aren’t allowed except in projector display on/off command strings.

3. AT-HDVS-RX RS-232 port settings:
115200 bps, 8 bit data length, No parity bit, 1 bit stop-bit, No flow control.

4. Feedback for a command repeats the original command.

5. If a command fails or is aborted, the feedback will be “COMMAND FAIL”.

6. Some commands support query function by parameter [?]
Example: To get projector’s display on command -> WP_DisplayOn[?]$
To get input status -> WP_Input[?]$

atlona.com

11

Toll free: 1-877-536-3976

Local: 1-408-962-0515

HDCP Reporting

-

+

CAT5e/6/7 IN FIRMWARE DC 24V

The HDVS-RX has three HDCP reporting modes: compliant, noncompliant, and auto.

Note: HDVS does not alter the signal in any way
Note: HDVS will not pass HDCP compliant source signal to a non HDCP display

Complaint
Reports to the source it is connected to an HDCP compliant device

Note: Will pass all HDCP compliant and non compliant source signals to an HDCP compliant display

NonCompliant
Reports to the source it is connected to an HDCP noncompliant device

Note: Some Apple products (and other PCs) will protect non HDCP conent, stoping nonHDCP
compliant displays from receiving even personal files such as: powerpoints, Excel, or word
files. Use this mode to pass nonHDCP content
Note: BlueRay content, apple TV, and other HDCP complaint source signals will not pass

Auto
Will report compliant or noncompliant to the source depending on what the display reports.

Note: This mode is made to work with direct connection to a display and will not work with Atlona
matrices

Connection and Installation

Video
HDBaseT

Audio

DISPLAY

ON/OFF

LINK

Control

or

HDMI IN

INPUT

SELECT

CAT5e/6/7 IN FIRMWARE DC 24V

HDMI OUT

VGA IN

+-+

-

L

AUDIO OUT

AUDIO IN

AT-HDVS-TX-WP

-

POWER

LINK

R

RS232

MENU

-

+

+

atlona.com

Toll free: 1-877-536-3976

12

Local: 1-408-962-0515

Specifications

Video Resolutions

IN 480i, 480p, 576i, 576p, 720p@25/29/30/50/59/60Hz,
1080i@50/59/60Hz, 1080p@23/24/25/29/30/50/59/60Hz
640x480, 720x400, 800x600, 1024x768, 1152x864, 1280x768,
1280x800, 1280x960, 1280x1024, 1366x768, 1400x1050
1440x900, 1600x900, 1600x1200, 1680x1050, 1920x1200RB
Colorspace RGB, YCbCr 444, YCbCr 422
Color Depth 10-bit, 12-bit, 16-bit

Audio

Formats PCM 2Ch, LPCM 5.1, LPCM 7.1, Dolby Digital, DTS 5.1,
Dolby Digital Plus, Dolby TrueHD, DTS-HD Master Audio
Sample Rate 44.1kHz, 48kHz, 96kHz, 192kHz

Distance

HDMI 10 meters 30 feet
CAT5e/6 60 meters 197 feet
CAT6a/7 70 meters 230 feet

Signal

Bandwidth 6.75 Gbps
CEC No
HDCP Compliant

Temperature

Operating 0°C to 40°C 32°F to 104°F
Storage -20°C to 60°C -4°F to 140°F
Humidity 20 to 90% non-condensing

Power

Consumption 15W (varies per paired transmitter)
Supply Input: AC100-240V ~ 50/60Hz
Output: DC 24V/2.7A (to RX)

Dimension

H x W x D 30 x 122 x 125 (mm) 1.18 x 4.8 x 4.92 (inch)

Weight

Device 0.31 kg 0.67 lbs
Shipping

Certification

Unit CE, FCC
Power Supply CE, FCC, RoHs, cULus

atlona.com

13

Toll free: 1-877-536-3976

Local: 1-408-962-0515

Safety Information

Safeguards

To reduce the risk of electric shock, do not
expose this product to rain or moisture

If the wall plug does not fit into your local
power socket, hire an electrician to replace
your obsolete socket.

Do not modify the wall plug. Doing so will
void the warranty and safety features.

This equipment should be installed near
the socket outlet and the device should
be easily accessible in the case it requires
disconnection.

Precautions

FCC regulations state that any unauthorized changes or modifications to this equipment, not
expressly approved by the manufacturer, could void the user’s authority to operate this equipment.

Operate this product using only the included external power supply. Use of other power supplies
could impair performance, damage the product, or cause fires.

In the event of an electrostatic discharge this device may automatically turn off. If this occurs,
unplug the device and plug it back in.

Protect and route power cords so they will not be stepped on or pinched by anything placed on or
against them. Be especially careful of plug-ins or cord exit points from this product.

Avoid excessive humidity, sudden temperature changes or temperature extremes.

Keep this product away from wet locations such as bathtubs, sinks, laundries, wet basements, fish
tanks, and swimming pools.

Use only accessories recommended by Atlona to avoid fire, shock, or other hazards.

Unplug the product before cleaning. Use a damp cloth for cleaning and not cleaning fluid or
aerosols. Such products could enter the unit and cause damage, fire, or electric shock. Some
substances may also mar the finish of the product.

Never open, remove unit panels, or make any adjustments not described in this manual. Attempting
to do so could expose you to dangerous electrical shock or other hazards. It may also cause damage
to your product. Opening the product will void the warranty.

Do not attempt to service the unit. Disconnect the product and contact your authorized Atlona
reseller or contact Atlona directly.

atlona.com

14

Toll free: 1-877-536-3976

Local: 1-408-962-0515

Atlona, Inc. (“Atlona”) Limited Product Warranty Policy

Coverage

Atlona warrants its products will substantially perform to their published specifications and will be free from defects in
materials and workmanship under normal use, conditions and service.

Under its Limited Product Warranty, Atlona, at its sole discretion, will either:

A) repair or facilitate the repair of defective products within a reasonable period of time, restore products to their
proper operating condition and return defective products free of any charge for necessary parts, labor and shipping

OR

B) replace and return, free of charge, any defective products with direct replacement or with similar products deemed
by Atlona to perform substantially the same function as the original products

OR

C) refund the pro-rated value based on the remaining term of the warranty period, not to exceed MSRP, in cases
where products are beyond repair and/or no direct or substantially similar replacement products exist.

Repair, replacement or refund of Atlona’s products is the purchaser’s exclusive remedy and Atlona’s liability does not
extend to any other damages, incidental, consequential or otherwise.

This Limited Product Warranty extends to the original end-user purchaser of Atlona’s products and is non-transferrable to
any subsequent purchaser(s) or owner(s) of these products.

Coverage Periods

Atlona’s Limited Product Warranty Period begins on the date of purchase by the end-purchaser. The date contained on
the end-purchaser ‘s sales or delivery receipt is the proof purchase date.

Limited Product Warranty Terms – New Products

• 10 years from proof of purchase date for hardware/electronics products purchased on or after June 1, 2013

• 3 years from proof of purchase date for hardware/electronics products purchased before June 1, 2013

• Lifetime Limited Product Warranty for all cable products

Limited Product Warranty Terms – Refurbished (B-Stock) Products

• 3 years from proof of purchase date for all Refurbished (B-Stock) hardware and electronic products purchased on or
after June 1, 2013

Remedy

Atlona recommends that end-purchasers contact their authorized Atlona dealer or reseller from whom they purchased
their products. Atlona can also be contacted directly. Visit www.atlona.com for Atlona’s contact information and hours
of operation. Atlona requires that a dated sales or delivery receipt from an authorized dealer, reseller or end-purchaser is
provided before Atlona extends its warranty services. Additionally, a return merchandise authorization (RMA) and/or case
number, is required to be obtained from Atlona in advance of returns.

Atlona requires that products returned are properly packed, preferably in the original carton, for shipping. Cartons not
bearing a return authorization or case number will be refused. Atlona, at its sole discretion, reserves the right to reject
any products received without advanced authorization. Authorizations can be requested by calling 1-877-536-3976 (US
toll free) or 1-408- 962-0515 (US/international) or via Atlona’s website at www.atlona.com.

Exclusions

This Limited Product Warranty excludes:

• Damage, deterioration or malfunction caused by any alteration, modification, improper use, neglect, improper
packing or shipping (such claims must be presented to the carrier), lightning, power surges, or other acts of nature.

• Damage, deterioration or malfunction resulting from the installation or removal of this product from any installation,
any unauthorized tampering with this product, any repairs attempted by anyone unauthorized by Atlona to make
such repairs, or any other cause which does not relate directly to a defect in materials and/or workmanship of this
product.

• Equipment enclosures, cables, power supplies, batteries, LCD displays, and any accessories used in conjunction with
the product(s).

• Products purchased from unauthorized distributors, dealers, resellers, auction websites and similar unauthorized
channels of distribution.

atlona.com

15

Toll free: 1-877-536-3976

Local: 1-408-962-0515

Disclaimers

This Limited Product Warranty does not imply that the electronic components contained within Atlona’s products will
not become obsolete nor does it imply Atlona products or their electronic components will remain compatible with any
other current product, technology or any future products or technologies in which Atlona’s products may be used in
conjunction with. Atlona, at its sole discretion, reserves the right not to extend its warranty offering in instances arising
outside its normal course of business including, but not limited to, damage inflicted to its products from acts of god.

Limitation on Liability

The maximum liability of Atlona under this limited product warranty shall not exceed the original Atlona MSRP for
its products. To the maximum extent permitted by law, Atlona is not responsible for the direct, special, incidental or
consequential damages resulting from any breach of warranty or condition, or under any other legal theory. Some
countries, districts or states do not allow the exclusion or limitation of relief, special, incidental, consequential or indirect
damages, or the limitation of liability to specified amounts, so the above limitations or exclusions may not apply to you.

Exclusive Remedy

To the maximum extent permitted by law, this limited product warranty and the remedies set forth above are exclusive
and in lieu of all other warranties, remedies and conditions, whether oral or written, express or implied. To the maximum
extent permitted by law, Atlona specifically disclaims all implied warranties, including, without limitation, warranties
of merchantability and fitness for a particular purpose. If Atlona cannot lawfully disclaim or exclude implied warranties
under applicable law, then all implied warranties covering its products including warranties of merchantability and fitness
for a particular purpose, shall provide to its products under applicable law. If any product to which this limited warranty
applies is a “Consumer Product” under the Magnuson-Moss Warranty Act (15 U.S.C.A. §2301, ET SEQ.) or other
applicable law, the foregoing disclaimer of implied warranties shall not apply, and all implied warranties on its products,
including warranties of merchantability and fitness for the particular purpose, shall apply as provided under applicable
law.

Other Conditions

Atlona’s Limited Product Warranty offering gives legal rights, and other rights may apply and vary from country to
country or state to state. This limited warranty is void if (i) the label bearing the serial number of products have been
removed or defaced, (ii) products are not purchased from an authorized Atlona dealer or reseller. A comprehensive list of
Atlona’s authorized distributors, dealers and resellers can be found at www.atlona.com .

Atlona, Inc Product Registration

Thank you for purchasing this Atlona product. - We hope you enjoy it and will take an extra few
moments to register your new purchase.

Registration creates an ownership record if your product is lost or stolen and helps ensure you’ll
receive notification of performance issues and firmware updates.

At Atlona we respect and protect your privacy, assuring you that your registration information is
completely secure. Atlona product registration is completely voluntary and failure to register will not
diminish your limited warranty rights.

To register go to: http://www.atlona.com/registration

atlona.com

16

Toll free: 1-877-536-3976

Local: 1-408-962-0515