Page 1
HEATED BASE-HB SERIES
Service and Installation Manual
Please read this manual completely before attempting to install or operate this equipment!
Notify carrier of damage! Inspect all components immediately. See page 2.
HEATED BASE-HB SERIES
ELECTRICALLY HEATED
UNDER-COUNTER
Effective Date: 2019
IMPORTANT INFORMATION
READ BEFORE USE
Page 2
CONTENTS
RECEIVING & INSPECTING EQUIPMENT....................................................................................................................................................................................1
SERIAL AND MODEL # LOCATION..............................................................................................................................................................................................1
HB - SPECIFICATIONS, FEATURES AND ACCESSORIES.........................................................................................................................................................2
ELECTRICAL CHARACTERISTICS AND CUT-OUT REQUIREMENTS....................................................................................................................................3
OPERATION AND S/S MAINTENANCE........................................................................................................................................................................................4
PARTS LIST...........................................................................................................................................................................................................................................5
TROUBLE SHOOTING GUIDE..........................................................................................................................................................................................................6
ELECTRICAL SCHEMATIC.................................................................................................................................................................................................................7
LIMITED WARRANTY.........................................................................................................................................................................................................................8
WARRANTY INFORMATION............................................................................................................................................................................................................9
RECEIVING AND INSPECTING THE EQUIPMENT
1. VISUALLY INSPECT THE SHIPPING CRATE. DAMAGE SHOULD BE NOTED AND REPORTED TO THE DELIVERING CARRIER.
2. IF DAMAGED, OPEN AND INSPECT CONTENTS WITH CARRIER.
3. IF CRATE IS NOT DAMAGED AND THERE IS CONCEALED DAMAGE TO THE EQUIPMENT, NOTIFY THE CARRIER. NOTIFICATION MUST BE
MADE VERBALLY AND IN WRITING.
4. REQUEST AN INSPECTION BY THE SHIPPING COMPANY FOR THE DAMAGED EQUIPMENT WITHIN 10 DAYS FROM RECEIPT OF THE
EQUIPMENT
5. FREIGHT CARRIERS CAN SUPPLY THE NECESSARY FORMS ON REQUEST.
6. SAVE ALL CRATING MATERIALS UNTIL INSPECTION HAS BEEN MADE OR WAIVED.
SERIAL NUMBER LOCATION
THE SERIAL AND MODEL# CAN BE FOUND ON THE OPERATORS CONTROL PANEL. WHEN CALLING ATLAS FOR PARTS AND SERVICE
ALWAYS HAVE THIS INFORMATION AVAILABLE.
SERIAL #: _______________________________________________________
MODEL #:_______________________________________________________
INSTALLATION DATE: _____________________________________________
Page 3
Project: ___________
Item No.: ___________
Quantity: ___________
SLIDE-IN SERVING EQUIPMENT
HEATED
BASE
Electrically Heated
Under Counter
HB-3
HB-4
HB-5
BODY: Double wall constructed with 20 gauge, type 304
stainless steel interior liner, with coved corners. Exterior wall
is 22 gauge galvanized steel, with an 18 gauge stainless
steel facia. The body is filled with 1" of high density fiberglass insulation on all sides. Interior of the body is provided
with a removable slide assembly to accommodate 12" X 20"
pans.
DOORS: Doors are double wall constructed of 18 gauge,
type 304 stainless steel, fully insulated with high density
fiberglass, and provided with edge mounted, chrome plated
hinges and a slam action latch. Doors are complete with a
moisture-proof gasket.
ELECTRICAL: The unit is provided with an 850 watt element, pre-wired to an on/off thermostat switch and pilot light.
The unit is wired for 15 amp., 120 volt, single phase operation, with a 6’ long, 3-wire cord and plug (NEMA 5-15P).
Specifications subject to change without notice.
SPECIFICATIONS
STANDARD FEATURES
g
Slides into your counter - puts heated storage where
you need it
g
Fully insulated for maximum efficiency
g
Slide assembly for standard 12” x 20” pans
g
Electrically heated - thermostat control
g
1-Year Parts & Labor Warranty
g
UL Listed
DI-57
HB-3
Page 4
Atlas Metal Industries 1135 NW 159th Dr. Miami, FL 33169 (800) 762-7565 Fax: (305) 623-0475 atlasfoodserv.com
DI-58
MODEL “A”
STORAGE CAPACITY
12” X 20” PANS
CUT-OUT
REQUIRED
ELECTRICAL
CHARACTERISTICS
SHIP WT.
(LBS.)
HB-3
41-7/8”
(106cm)
8
15-3/4” X 41-7/8”
(40 X 106cm)
850 W - 7.1 amps.
120V
190
(86.1kg)
HB-4
55-5/8”
(140.9cm)
12
15-3/4” X 55-5/8”
(40 X 140.9cm)
850 W - 7.1 amps.
120V
265
(120.2kg)
HB-5
69-3/8”
(175.8cm)
16
15-3/4” X 69-3/8”
(40 X 175.8cm)
850 W - 7.1 amps.
120V
312
(141.5kg)
“A”
23-5/8”
PLAN VIEW
15-3/4”
14-1/8”
15-1/2”
29-1/8”
FRONT ELEVATION
14-5/8”
END VIEW
2/19-sc
Page 5
SLIDE- IN HEATED BASE
HB SERIES
--------------------------------------------------------------------------------------------------------------------------------------------------------------------
--------------------------------------------------------------------------------------------------------------------------------------------------------------------
OPERATION
The unit is ready to operate as soon as it is plugged in and turned on. The thermostat has an off position and
numbers from #1 through #10 (number 10 is the highest setting).
The unit is supplied with a power cord and NEMA plug. Refer to the data plate for the amperage and voltage
information. Use a licensed electrician when installing power source.
--------------------------------------------------------------------------------------------------------------------------------------------------------------------
--------------------------------------------------------------------------------------------------------------------------------------------------------------------
MAINTENANCE
NEVER CLEAN THE UNIT WITH A CHLORIDE BASED PRODUCT. CHLORIDES OR IMPROPER
CLEANING COULD SCAR, MARK AND/OR CORRODE METAL. DO NOT
ABRASIVE PRODUCTS. TO CLEAN USE SOAPY WARM WATER, RINSE THOROUGHLY TO REMOVE
ALL RESIDUES. FAILURE TO MEET THESE CONDITIONS WILL VOID WARRANTY.
USE STEEL WOOL OR
Page 6
Subsidiary of Mercury Aircraft, Inc.
1135 N.W. 159th DR., MIAMI, FL 33169
PHONE (305) 625-2451, (800) 762-7565, FAX (305) 623-0475, E-mail: sales@atlasfoodserv.com
PARTS LIST ELECTRICAL HEATED BASE
HB SERIES
1
2
4
8
10
ITEM
NUMBER
1
2 22-1407
9
P ART
NUMBER
1001-0
1002-0 Power Cord 14/3-15 Amps 120V
HB-4 SHOW N
DESCRIPTION
Power Cord 14/3-15 Amps 240V
Thermostat Knob
3 1100-0
4 1105-0
5
6
7010-3
7013-3 #4 & #5 Door Gasket
S83754-4 Door Assembly HB-5
#3 & #4 Door Gasket
7 S83753-0 Pan Rack
8
9 S83754-3
10 6053-8
11 1087-0
12 2500-1
13
6055-1 Slam Action Latch
6052-1 Slam Action W/ Lock
Door Assembly HB-3, HB-4
Hinge & Cover
Cord Connector (Not Shown)
Thermostat (Not Shown)
1053-0
120V / 850W Element (Not Shown)
1054-0 208V / 850W Element (Not Shown)
1055-0 240V / 850W Element (Not Shown)
3
7
Pilot Light
Thermometer
6
5
Page 7
Subs
idiary of Mercury Aircraft, Inc.
1135 N.W. 159th DR., MIAMI, FL 33169
PHONE (305) 625-2451, (800) 762-7565, FAX (305) 623-0475, E-mail: sales@atlasfoodserv.com
Electric Hot Food Drop-In Trouble Shooting Guide
Symptom Probable Cause
Unit not plugged in.
Unit will not heat
No power at receptacle.
Thermostat and or switch not in the on position.
Call factory for service at 1-800-762-7565
Thermostat’s not turned to the highest setting.
Food products not hot enough when placed in unit.
Food products not
hot enough.
Food product not being stirred or rotated.
Heat lamp or head strip over the food product is recommended.
Call factory for service at 1-800-762-7565.
NOTE:
Before starting any warranty repair work you must first call the factory for authorization.
Failure to do so can make you responsible for repair cost.
Page 8
Page 9
LIMITED WARRANTY
Atlas Metal Industries, Inc. warrants to the Purchaser of this product that the
same shall be free from defects in the workmanship and material for a period of
one year from the date of original installation of the equipment, but not to exceed
eighteen (18) months after date of shipment from factory. During this period of
time Atlas Metal Industries, Inc. will replace all defective parts and will pay for
authorized replacement labor. Replacement and installation of such parts and
labor shall be provided only upon prior written authority of Atlas Metal Industries,
Inc.
The Refrigeration warranty is for a twenty (20) month time period and includes
supplying the compressor at a no charge basis provided the damage to the
compressor was not caused by the customer or end user. Authorized
replacement labor will be paid for a period of one year from date of installation.
Freight costs for defective unit to and from Atlas Metal Industries, Inc. are not
included, and all defective parts must be returned to the factory freight prepaid
for evaluation. ALL WARRANTY LABOR MUST BE AUTHORIZED BY ATLAS
METAL INDUSTRIES, INC. PRIOR TO THE ACTUAL WORK BEING DONE.
This warranty does not apply to any equipment or any part thereof, which has
been subjected to shipping damage, improper voltage, alteration, abuse or
misuses, and does not cover loss of food, other products, or damage to property
due to mechanical or electrical malfunction.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE
DESCRIPTION OF THE FACE HEREOF. SELLER DISCLAIMS ANY IMPLIED
WARRANTY OF MERCHANTABILITY OF THE GOODS OR THE FITNESS OF
THE GOODS FOR ANY PURPOSE AND BUYER AGREES THAT THE GOODS
ARE SOLD “AS IS.”
Page 10
WARRANTY INFORMATION
In order to have your invoice approved for
payment by the factory, please note the following:
_______________________________________________
An authorization number must be obtained from
the factory prior to performing any warranty
service.
_______________________________________________
Atlas Metal will not approve excessive labor due to poor
access to the unit being serviced. If design does not
allow reasonable access, contact the factory.
_______________________________________________
All travel time that exceeds 100 miles round trip
must be authorized by the factory.
_____________________________________________________________________________________
Thank You:
Warranty service Dept.
Loading...