Page 1
OPERATION AND MAINTENANCE MANUAL
MOBILE MODULAR SELF
SERVICE MILK UNIT
MODEL: BMM-1000
Page 2
GENERAL INFORMATION
The BMM-1OOO series Self Serving Milk Units are equipped with refrigerated compartment to hold (12) 13"
x 13" x 11" milk cases.
UNPACKING:
Examine the interior of the unit and make sure all packing materials, such as wood and cardboard removed
before unit is plugged in to an outlet. Examine the exterior and interior of the unit to determine
whether any damage was incurred during delivery. If so, notify the carrier or your dealer immediately to file
a damage claim. All ATLAS equipment is carefully tested and inspected prior to shipment. When accepted
for delivery by the carrier, the responsibility for safe arrival is assumed by the carrier.
INSTALLING:
These units have been carefully designed to meet your required operational needs: Prior to operating these
units, it is important to check the following:
1. Supply cord and plug for possible damage due to shipping. (Loose wires, fraying, or cuts in cord.)
2. Temperature controls must not have any “play or movement with exception of control knob.”
3. Plug in to proper electrical receptacle as indicated on the rating plate of each unit .
WARNING: SHOULD ANY DAMAGE BE FOUND AFTER GOING THROUGH THE ABOVE CHECK LIST, DO NOT
ATTEMPT TO OPERATE UNIT. CALL YOUR DEALER IMMEDIATELY TO ARRANGE FOR FACTORY AUTHORIZED
SERVICE.
OPERATING:
For equipment containing refrigeration units, allow adequate time after 'turn-on" for units to reach
proper temperature. Time varies depending on ambient temperature and locations. The unit will
maintain proper temperature, cycling on its pressure control, so field adjustment should not be necessary.
MAINTENANCE:
This equipment has been designed to require minimum maintenance and has been constructed to meet
National Sanitation Foundation, Underwriters Laboratory Standards, and U.S. Public Health Service
Standards.
Non-toxic chemical cleaners or mild detergents are recommended for cleaning of fixtures. Do NOT use steel
wools at any kind. Steel wool particles will work in to the grains of the metal causing corrosion. Also, these
particles can cause a health hazard. Should scouring be required, use a non-abrasive type of cleaner. Do not
use caustic solutions on your equipment. Hosing or steam cleaning should not be necessary to keep these
fixtures clean and sanitary. Do not allow water or steam to come In contact with electrical components.
WARNING: Be sure to disconnect power source before cleaning or servicing the unit. Liability for improper
or careless use is the responsibility at the equipment owner or persons servicing the unit, including
authorized service agents.
Page 3
PARTS LIST
ITEM NO.
1
2
3
4
5
6
7
8
9
10
11
12
DESCRIPTION PART NO.
CONDENSING UNIT 2004-1
5” CASTER W/O BRAKE 1800-497
5” CASTER W/BRAKE 1800-499
LATCH, SASH. CHROME 1800-3870
SWITCH MAIN ON/OFF 1800-3955
COVER PLATE SWITCH 1800-4054
THERMOMETER CLIP-ON 4913-4
BOTTOM, FALSE P40225-000
LOCK, FRONT DOOR P41593-000
HINGE, LEFT LID P42293-000
HINGE, RIGHT LID P42294-000
HINGE, CENTER P42295-000
13
14
LATCH, DOOR LOCK P42760-000
BRACKET, TRAY SLIDE 70045-8
13
8
14
2
3
Page 4
COMPRESSOR SCHEMATIC
Page 5
TEMPERATURE CONTROL
Should readjusting the temperature be necessary, turn the adjustment screw as illustrated below:
Adjust this screw only.
Turn clockwise to achieve colder temperature.
Turn counterclockwise to achieve warmer temperature.
Turn approximately 1/4 turn for each degree of temperature
change desired.
THIS CONTROL IS LOCATED IN THE
COMPRESSOR COMPARTMENT
Page 6
LIMITED WARRANTY
Atlas Metal Industries, Inc. warrants to the Purchaser of this product that the
same shall be free from defects in the workmanship and material for a period of
one year from the date of original installation of the equipment, but not to exceed
eighteen (18) months after date of shipment from factory. During this period of
time Atlas Metal Industries, Inc. will replace all defective parts and will pay for
authorized replacement labor. Replacement and installation of such parts and
labor shall be provided only upon prior written authority of Atlas Metal Industries,
Inc.
The Refrigeration warranty is for a twenty (20) month time period and includes
supplying the compressor at a no charge basis provided the damage to the
compressor was not caused by the customer or end user. Authorized
replacement labor will be paid for a period of one year from date of installation.
Freight costs for defective unit to and from Atlas Metal Industries, Inc. are not
included, and all defective parts must be returned to the factory freight prepaid
for evaluation. ALL WARRANTY LABOR MUST BE AUTHORIZED BY ATLAS
METAL INDUSTRIES, INC. PRIOR TO THE ACTUAL WORK BEING DONE.
This warranty does not apply to any equipment or any part thereof, which has
been subjected to shipping damage, improper voltage, alteration, abuse or
misuses, and does not cover loss of food, other products, or damage to property
due to mechanical or electrical malfunction.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE
DESCRIPTION OF THE FACE HEREOF. SELLER DISCLAIMS ANY IMPLIED
WARRANTY OF MERCHANTABILITY OF THE GOODS OR THE FITNESS OF
THE GOODS FOR ANY PURPOSE AND BUYER AGREES THAT THE GOODS
ARE SOLD “AS IS.”
Page 7
WARRANTY INFORMATION
In order to have your invoice approved for
payment by the factory, please note the following:
_______________________________________________
An authorization number must
be obtained from
the factory prior to performing any warranty
service.
_______________________________________________
Atlas Metal will not approve excessive labor
due to poor
access to the unit being serviced. If design does not
allow reasonable access, contact the factory.
_______________________________________________
All travel time that exceeds 100 miles round trip
must
_____________________________________________________________________________________
Thank You:
Warranty service Dept.
be authorized by the factory.
Loading...