AtlasIED TSD-MIX42RT Users Guide

Owner’s Manual

TSD-MIX42RT

4x2 Mic/Line Mixer

TSD-MIX42RT

4x2 Mic/Line Mixer with

Priority Sense and Remote Control

1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A.

Telephone: [phone] • Fax: [phone]

AtlasIED.com – 1 –

Specifications are subject to change without notice.

TSD-MIX42RT

4x2 Mic/Line Mixer

Owner’s Manual

Description

The versatile AtlasIED TSD-MIX42RT 4x2 mic/line mixer is ideal for applications where paging,
priority music override and/or remote input selection with level control are required. Use alone or in
conjunction with amplifiers in meeting rooms, digital signage, luxury suites, and/or other applications
requiring versatile, stereo or mono multi source mix control.

The unit includes one mic/balanced line input via removable Phoenix style connector and three
stereo 3.5mm inputs. Switchable phantom power is provided for the mic input to facilitate condenser
microphones. The high quality, low noise internal mic preamps ensure clarity and quiet operation
without unwanted coloration. A 12dB/octave high pass filter @ 125Hz also is available on the mic
input to minimize bass rumble and low frequency feedback.

Priority paging can be accomplished via contact closure or VOX trigger on Input 1 that will mute
Inputs 2, 3, or 4 (assignable). A remote level control feature allows use of the AtlasIED AAVC-10K
or WPD-VC10K decorative wall plate control for convenient remote adjustment of either the entire
Master mix bus or Inputs 2, 3, or 4.

Remote Input selection and level control can be accomplished by using the optional WPD-MIX42RT
wall controller. The WPD-MIX42RT can be placed up to 200 ft away from the TSD-MIX42RT. The audio
quality is not affected by the distance because no audio is present at the WPD wall controller. All that
is needed to obtain maximum system control are 8 conductors, a TSD-MIX42RT and a WPD-MIX42RT.

There are several installations that require audio override sensing for applications such as a Juke
Box’s playback or digital signage advertisement. The TSD-MIX42RT is ideal for these types of
installations. When Input 3 is assigned to Juke Box Override and receives a signal, it mutes stereo
Inputs 1 and 2. When the audio is not present on Input 3 for 20 seconds, Inputs 1 and 2 fade back in
and resumes play.

A variable output limiter provides system protection by reducing clipping and distortion - which is
especially useful when mixing mic and/or line sources with varying volumes.

The TSD-MIX42RT is part of a full line of AtlasIED Time Saving Devices. These compact
(1.5" x 4" x 2.5") units are designed to solve some of the common audio system problems in the easiest,
most efficient, and cost-effective way. All models are made from high quality components and
include removable individual I/O connectors for quick and precise wiring, separate ground terminals
for all I/Os assuring secured connections, and removable level controls that can be replaced with
tamper-resistant security covers. The TSDs are highly efficient and meet most energy standards as
one 24V DC power supply (available separately) can power multiple Atlas Time Saving Devices.

1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A.

Telephone: [phone] • Fax: [phone]

AtlasIED.com – 2 –

Specifications are subject to change without notice.

Owner’s Manual

TSD-MIX42RT

4x2 Mic/Line Mixer

Features

• Stereo or Mono Configurations

• One Balanced Mic/Line Input

• Switchable 24V Phantom Power

• Three Unbalanced Stereo Line Inputs 3.5mm

• Vox Sense and Contact Closure, Priority Mute

• Variable Output Limiter

• Remote Level Control

• 12dB/Octave Low Cut Filter @ 125Hz Mic/Line

• Remote Control Input Select & Level Control

• Audio Auto Sensing Juke Box Override

• Input Signal & Peak Indicator LEDs

• High Gain Output for Driving Long Balanced Lines

• Separate Ground Connections

• Security Covers Included for All Front Panel Controls

• Cable Management System

• Multiple Mounting Congurations

• Removable Phoenix Style I/O Connectors

• Meets Most Energy Standards

• Compact Chassis Design

Audio Applications

• Mixer

• Mic Preamp

• Line Preamp

• Stereo Summing Preamp

• Line Drive

• Remote Level Control

• Priority Paging

• Music Override

• Digital Signal Auto Sense

Installation

• Restaurants

• Sports Bars

• Schools

• Industrial Facilities

• House of Worship

1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A.

Telephone: [phone] • Fax: [phone]

AtlasIED.com – 3 –

Specifications are subject to change without notice.

TSD-MIX42RT

4x2 Mic/Line Mixer

Owner’s Manual

Front Panel Description

4

3

2

1

5

1. Power LED - Illuminates Blue when 24VDC power is present.

2. Signal LED - Illuminates Green when the input signal strength reaches 25mV to verify a signal
path. Note: The LED will not illuminate if the input level is turned Off.

3. Input Peak LED - Illuminates Red when the output signal reaches 3dBV below when signal clipping

will occur. Occasional ashing is normal but if this indicator is continuously On, then reduce the

input level using the input level control on the front panel.

4. Limiter LED - Adjustment of the Limiter feature should be done after the input gain(s) have been
properly set. Each Input should be adjusted so the Output Limiter control can be set so this LED

ashes to indicate that the limiter circuit is active.

5. Input Level Controls 1, 2, 3, and 4 - Independently adjust the level of input signals 1 through 4. Turn
clockwise to increase the signal level and counter-clockwise to decrease it. Note: The Input Level
Control knobs can be removed and replaced with a supplied security cover to prevent
unauthorized adjustment.

1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A.

Telephone: [phone] • Fax: [phone]

AtlasIED.com – 4 –

Specifications are subject to change without notice.

Owner’s Manual

TSD-MIX42RT

4x2 Mic/Line Mixer

Rear Panel Description

5 2 6 10 11 12

9 9

99

1 4

TSD Input/Output connections are removable for easy system wiring. The connectors have a 3.5mm
pitch between pins.

1. DC Power Input - Each TSD that requires DC power comes with a 2 position connector for an
external 24VDC power supply (sold separately). Because of the TSD’s low power consumption, a

single external power supply may power more than one TSD. Please refer to the specications

on current requirements in milliamps to match with the appropriate power supply. Please observe
the polarity of the wiring to this connector. Note: It is acceptable to exceed the current
requirements of the TSDs but NOT safe to use a power supply that is below the current
requirement of the device.

2. Mic/Line Input 4 - Connects to balanced line or mic level sources. For gain or source input type

selection, refer to the “Dip Switch Function Identication” chart. Note: Unbalanced line inputs can
be inserted with proper wire conguration by connecting the (G) and (-) terminals together.

3. Unbalanced Inputs 1 & 2 Stereo 3.5mm (1⁄8") - Stereo Unbalanced Audio Signals.

4. Unbalanced Input 3 - Stereo Unbalanced Audio Signal. Input 3 is also the auto sense Juke Box
Override input. Note: Juke Box Override will not work when Remote Wall Plate is activated.

5. Remote Mute - To mute Input 1, 2, or 3 via a remote switch, assign which channels you want to be
muted via the dip switch provided and short the two terminals together using a dry contact closure.

6. VOX Sense - Adjusts the sensitivity of the Mute circuit for priority pages. Assign the input to be
muted via the corresponding dip switch.

7. Balanced Left & Right Output - Provides output for connection to balanced line level devices.
Note: Unbalanced line level devices can be used with proper wire conguration by connecting

the (G) and (-) terminals together. Mono or stereo congurations are assigned via the associated
Dip switch. When Dip switch 9 is down or “Mono”, both outputs receive a summed L + R signal.

87 3

1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A.

Telephone: [phone] • Fax: [phone]

AtlasIED.com – 5 –

Specifications are subject to change without notice.

TSD-MIX42RT

4x2 Mic/Line Mixer

8. Output Limiter Control - Sets peak output levels by increasing or decreasing the sensitivity.
The Limiter LED on the front panel indicates when limiter is in use.

9. Cable Management Retainer Points - Each TSD includes two cable retainer straps for securing
the included cable management retainers. Remove one of the rear panel screws, align the

panel hole with a retainer and rmly tighten the screws.

10. Remote Level - For remote gain control, connect the AtlasIED AAVC-10K (or equal) wall plate to
this terminals. Set dip switch 10 to control a mixed signal or Inputs 1, 2, and 3 signal only.

11. DC Output (Remote LED) - A 12VDC output is provided to power a remote system ON LED Indicator
on the WPD-MIX42RT wall controller.

12. Wall Plate Interface Input Selection - Inputs 1, 2, and 3 can be remotely selected by shorting the
terminals 1, 2 or 3 to ground. The WPD-MIX42RT provides proper connectivity to easily do this.

Owner’s Manual

Wall Plate Interface

The TSD-MIX42RT is designed to mate with the optional wall plate WPD-MIX42RT. This control
accessory allows you to select Inputs to be sent to the Output, along with a system level control and
a remote system on power indicator. To activate the input selection section, you must assign the
corresponding dip switch. Note: Placement of the WPD-MIX42RT can be placed up to 200 ft away
from the TSD-MIX42RT. The audio quality is not affected by the distance because no audio is present
at the WPD wall controller. All that is needed to obtain maximum system control is 8 conductors,
TSD-MIX42RT and a WPD-MIX42RT. Cat5 cable is ok to use. Note: Juke Box Override will not work
when Remote Wall Plate is activated.

1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A.

Telephone: [phone] • Fax: [phone]

AtlasIED.com – 6 –

Specifications are subject to change without notice.

Owner’s Manual

TSD-MIX42RT

4x2 Mic/Line Mixer

Dip Switch Function Identication

Switch Position

• Dip Switch # 1 - 24VDC Phantom Power applies power for condenser mic operation to
corresponding input terminal. Down position is ON.

• Dip Switch # 2 - Input Mic or Line Select for input gain selection for Input 4. Up position is Line,
down position is Microphone.

• Dip Switch # 3 - Low Cut Filter engages at 125Hz with a roll off rate of 12dB per octave. This lter
operates either in the Line or Mic mode and is available on Input 4. Ideal for vocal microphones
to reduce low frequency energy and to increase intelligibility. Down position is ON.

• Dip Switch # 4 - Input 3 can be used as an Audio Override to Mute Inputs 1 & 2. When set to the
ON position, if Input 3 receives a signal it will mute Inputs 1 or 2 if they are set to Mute Receive
ON. This is also known as a Juke box Override feature. See DIP SW 5 for delay settings. If the
switch is in the OFF position, standard mix summing Inputs 1, 2 and 3 can be done. Note: VOX &
Remote CC will also Mute Inputs 1, 2, and 3 if they are assigned to Mute Receive.

• Dip Switch # 5 - Corresponds with DIP SW 4 ON settings. When Input 3 receives a signal to
mute Inputs 1 or 2, you need to select the length of time needed to sustain the mute. This will
depend on the application and/or audio source material triggering the Override function at
Input 3; you may want short or long Mute Delay (hold) time after the signal has stopped at
Input 3 to assure a smooth transition from Input 3 to inputs 1 or 2.

• Dip Switch # 6 - Input 3 will be muted when audio is present at Input 4 or when the mute CC
pins are shorted together. Down position is mute receive ON.

• Dip Switch # 7 - Input 2 will be muted when audio is present at Input 4 or when the mute CC
pins are shorted together. Down position is mute receive ON.

• Dip Switch # 8 - Input 1 will be muted when audio is present at Input 4 or when the mute CC
pins are shorted together. Down position is mute receive ON.

• Dip Switch # 9 - Outputs left and right can be congured for stereo left and right or combined

into a summed mono output. Up position is stereo and Down position both outputs receive a

“summed” L + R signal.

• Dip Switch # 10 - Remote level sets whether the remote volume control adjusts all inputs mixed
(Inputs 1, 2, 3, and 4) or Inputs 1, 2, and 3 only. Up position is all Inputs, down position is Inputs
1, 2, and 3.

• Dip Switch # 11 - Wall Plate Activation - This switch is used for the optional WPD-MIX42RT
remote wall controller. When the switch is in the UP position, it is OFF, meaning that all inputs
are active to the outputs. When in the ON position the wall controller selects Inputs 1, 2, or 3 to
be at the output of the TSD. Note: Input 4 is always present at the outputs in either mode. Note:
Juke Box Override will not work when Remote Wall Plate is activated.

• Dip Switch # 12 - Not Used

1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A.

Telephone: [phone] • Fax: [phone]

AtlasIED.com – 7 –

Specifications are subject to change without notice.

TSD-MIX42RT

4x2 Mic/Line Mixer

Owner’s Manual

Cable Management

Knob and Security Cover

All front panel level controls feature a removable knob that can be replaced with an included security
cover. Follow these steps to prevent potentiometer damage or unwanted changes.

1. Knob Installation - Turn the potentiometer shaft fully counter-clockwise. Align the knob indicator
to the lowest setting on the panel and the potentiometer shaft slot. Carefully press the knob onto
the potentiometer shaft. Do not force or damage may occur to the potentiometer.

2. Security Cover Installation - Remove the knob from the panel and insert the cover. Small pliers may
be required to remove the knobs. Align the security cover to the level control panel hole. Push the
cover into the hole until it snaps into place. Do not force or damage may occur to the potentiometer.

1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A.

Telephone: [phone] • Fax: [phone]

AtlasIED.com – 8 –

Specifications are subject to change without notice.

Owner’s Manual

TSD-MIX42RT

4x2 Mic/Line Mixer

Mounting

Listed below are the ways to mount the TSD and the optional accessories that can be purchased.

1. Velcro™ - Each unit includes two 2" x 2" pieces of industrial-grade Velcro™ with adhesive backing
to adhere to any at surface. Clean all surfaces before applying the adhesive side of the Velcro™.

2. Multi Mount Plate - Each TSD includes a versatile multi-position mounting plate. This plate
allows the TSD to be mounted to any surface; but is ideal for use with rear rack rails or side rack
hat channels. Use the included M3 x 4mm screws to install the plate on the TSD. Note: Only use
the included M3 x 4mm screws as other screws may be too long and will cause internal damage
to the TSD. The multi-position mounting plate is a new addition being included with TSDs. If the
TSD being used did not include the mounting plate, contact AtlasIED customer service at
1-800-876-3333.

1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A.

Telephone: [phone] • Fax: [phone]

AtlasIED.com – 9 –

Specifications are subject to change without notice.

(M3 x 4mm)

(M3 x 4mm)

TSD-MIX42RT

4x2 Mic/Line Mixer

Owner’s Manual

Optional Mounting Accessories

1. TSD-RMK 19" Width Rack Mount Kit - For 19" rack mounting, AtlasIED offers an optional rack
mount kit, the TSD-RMK. This rack mount kit can support up to four TSD units. The kit includes

three blank panels designed to ll any unused slots. Use the included hardware to mount the TSD

into the rack mount kit using the top mount screw holes on the TSD.

2. TSD-RMKHR Half Width Rack Mount Kit - AtlasIED offers an optional rack mount kit that can
be used in half width rack applications including the AtlasIED WMA-HR and AWR-HR models.

The TSD-RMKHR can support up to two TSDs. Included is an extra blank panel to ll one of the

spaces if only one TSD is being used.

1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A.

Telephone: [phone] • Fax: [phone]

AtlasIED.com – 10 –

Specifications are subject to change without notice.

Owner’s Manual

3. TSD-RRMK Rear Rack Mounting Kit - For complete exibility in mounting a TSD or TSD external
power supplies the optional TSD-RRMK is available. The TSD-RRMK can support mounting of
either two larger TSDs with external power supplies or up to 4 TSD models. Note: Only use the
included M3 x 4mm screws as other screws may be too long and will cause internal damage to
the TSD.

TSD-MIX42RT

4x2 Mic/Line Mixer

1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A.

Telephone: [phone] • Fax: [phone]

AtlasIED.com – 11 –

Specifications are subject to change without notice.

Block Diagram

SIGNAL PEAK

POWER SHOW

LED

PHANTOM

12

NCNCNC

11

WALL

10

REMOTE

9

OUTPUT

STEREO/

8

INPUT 1

7

INPUT 2

6

INPUT 3

5

JUKE

INPUT 3

DIP SWITCH FUNCTION SET

4

INPUT 3

3

INPUT 4

125Hz/12dB

2

INPUT 4

1

INPUT 4

TSD-MIX42RT

4x2 Mic/Line Mixer

3 2 1 GND

+12V

G 12V

OUTPUT INPUT

+5V

RMT

LEVEL

NC

ON

OFF

PLATE

LEVEL

MASTER

INPUT 1,2,3

MONO

MONO

STEREO

ON

OFF

MUTE RCV

ON

OFF

MUTE RCV

OFF

MUTE RCV

20 SEC

MUTE DELAY

OFF

JUKE OR

OFF

LOW CUT

LINE

OFF

ON

1 2 3 4 5 6 7 8 9 10 11 12

3 SEC

ON

ON

MIC

ON

LOW CUT

125Hz -3dB

MIC/

LINE

+

–

G

INPUT 4

LEVEL

INPUT 4

+5V

MUTE

ON FRONT

CC

PANEL

MCU

SDA

VOX

SENS

MUTE CONTROL

Owner’s Manual

OUTPUT L

DC24V

OUTPUT R

–

–

–

+

+

+

G

G

24V

OUTPUT

STEREO/MONO

L

R

LEVEL

PANEL

INPUT 3

ON FRONT

L

R

LIMITER LIMITER

LEVEL

PANEL

INPUT 2

ON FRONT

L

LEVEL

PANEL

INPUT 1

ON FRONT

L

L

L

CLK

RLRLR

LRLRL

INPUT 1

LIMITER

CONTROL

MASTER

VOLUME

VOLUME

ADJUSTMENT

R

R

R

R

INPUT 2

OUTPUT

INPUT 3

1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A.

Telephone: [phone] • Fax: [phone]

AtlasIED.com – 12 –

Specifications are subject to change without notice.

Owner’s Manual

TSD-MIX42RT

4x2 Mic/Line Mixer

Specications

Description 4 x 2 Stereo Line Mixer with Priority Sense & Remote Level

Chassis Color Black
Chassis Material Aluminum

Inputs
Type Qty 3, Unbalanced
Connection 3.5mm Stereo
Impedance 10kΩ
Input Level 316mV (-10dB) = 2V (+6dBV) Balanced Output,
Maximum Input 1.6V (4.1dBV)

Type Qty 1, Balanced Mic or Line Selectable
Connection Removable 3 Position Captive Screw 3.5mm Spacing
Impedance 1.2kΩ Balanced, 600Ω Unbalanced
Phantom 24VDC Defeatable
Low Cut Filter 125Hz/12dB Defeatable
Line Input Level 1V (0dBV) Balanced = 2V (+6dBV) Balanced Output,
Maximum Input 6V (6dBV)
Mic Input Level 46dB Gain, 10mV (-40dB) Balanced = 2V (+6dBV) Balanced Output,
Maximum Input 40mV (-27dBV)

Outputs
Type Qty 2, Balanced Line, Left & Right
Connection Removable 3 Position Captive Screw 3.5mm Spacing
Impedance 300Ω Balanced, 150Ω Unbalanced

Line Output Level 1V (0dBV) In = 2V (+6dBV), Maximum Output 6V (15dBV)

Controls
Input Level Control Qty 4, Removable Knobs with Security Covers
Mute CC Contact Closure, Removable 2 Position Captive Screw

3.5mm Spacing
VOX Mute Sens Trim Adjust for Mic Sensitivity
Output Limiter Threshold Adjust
Remote Level Control Port 10kΩ External Pot, Removable 2 Position Captive
Screw 3.5mm Spacing
DC 12V Output 12V DC to power wall controller LED, Removable 2 Position Captive
Screw 3.5mm Spacing
Wall Controller Interface Connects to optional WPD-MIX42RT wall controller, Removable 4
Position Captive Screw 3.5mm Spacing
Note: Juke Box Override will not work when Remote Wall Plate is
activated.

1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A.

Telephone: [phone] • Fax: [phone]

AtlasIED.com – 13 –

Specifications are subject to change without notice.

TSD-MIX42RT

4x2 Mic/Line Mixer

Dip Switch Function
Dip Switch # 1 24VDC Phantom Power
Dip Switch # 2 Input 4 Mic or Line Select
Dip Switch # 3 Low Cut Filter 125Hz
Dip Switch # 4 Juke Box Override
Dip Switch # 5 Juke Box Override Mute Hold Delay
Dip Switch # 6 Input 3 Mute Receive
Dip Switch # 7 Input 2 Mute Receive
Dip Switch # 8 Input 1 Mute Receive
Dip Switch # 9 Outputs Left and Right Stereo/Mono
Dip Switch # 10 Remote Level Master/Inputs 1,2,3
Dip Switch # 11 Wall Plate Activation
Dip Switch # 12 Not Used

Indicators
Input Signal Green, 25mV ON Threshold, Qty 1
Input Peak Red, -3dB Before Clip, Qty 1
Limiter Red, Limiter Activation, Qty 1
Power Blue, Qty 1

Electrical
Frequency Response 20Hz - 20kHz (±1dB)
THD .06% @ 1kHz
Signal to Noise Line to Line: 85dBV
Mic to Line: 78dBV
Output Limiter Threshold Adjust 50mV Minimum Output to No Limit

Power Requirements
Voltage 24VDC, 60mA
Power Consumption Current 60mA
Power Consumption VA Watts 1.4W

Dimensions H 1.5" (39mm) x W 4" (101mm) x D 2.5" (70mm)

Weight 13oz, .3kg

Included Accessories
Velcro™ Industrial-Grade
Multi-Mount Plate Qty 1, Includes Two (2) M3 x 4mm Screws
Cable Retainers Qty 2
Level Control Knobs Qty 4
Level Control Security Covers Qty 4

Optional Accessories
WPD-MIX42RT Wall Controller
TSD 24VDC Power Supply
TSD-RMK 1 RU 19" Width Rack Mount Panel (Supports 4 TSD Units)
TSD-RMKHR 1 RU Half Rack Width Panel (Supports 2 TSD Units)
TSD-RRMK Rear Rack Mounting Kit

Safety and Certifications
External Power Supply cUL, CE, RoHS, TUV

Owner’s Manual

1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A.

Telephone: [phone] • Fax: [phone]

AtlasIED.com – 14 –

Specifications are subject to change without notice.

Owner’s Manual

Notes:

TSD-MIX42RT

4x2 Mic/Line Mixer

1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A.

Telephone: [phone] • Fax: [phone]

AtlasIED.com – 15 –

Specifications are subject to change without notice.

TSD-MIX42RT

4x2 Mic/Line Mixer

Owner’s Manual

Limited Warranty

All products manufactured by AtlasIED are warranted to the original dealer/installer, industrial or
commercial purchaser to be free from defects in material and workmanship and to be in compliance
with our published specifications, if any. This warranty shall extend from the date of purchase for
a period of three years on all AtlasIED products, including SOUNDOLIER brand, and ATLAS SOUND
brand products except as follows: one year on electronics and control systems; one year on
replacement parts; and one year on Musician Series stands and related accessories. Additionally,
fuses and lamps carry no warranty. AtlasIED will solely at its discretion, replace at no charge or
repair free of charge defective parts or products when the product has been applied and used in
accordance with our published operation and installation instructions. We will not be responsible
for defects caused by improper storage, misuse (including failure to provide reasonable and
necessary maintenance), accident, abnormal atmospheres, water immersion, lightning discharge,
or malfunctions when products have been modified or operated in excess of rated power, altered,
serviced or installed in other than a workman like manner. The original sales invoice should be
retained as evidence of purchase under the terms of this warranty. All warranty returns must comply
with our returns policy set forth below. When products returned to AtlasIED do not qualify for repair
or replacement under our warranty, repairs may be performed at prevailing costs for material and
labor unless there is included with the returned product(s) a written request for an estimate of repair
costs before any nonwarranty work is performed. In the event of replacement or upon completion of
repairs, return shipment will be made with the transportation charges collect.

EXCEPT TO THE EXTENT THAT APPLICABLE LAW PREVENTS THE LIMITATION OF CONSEQUENTIAL
DAMAGES FOR PERSONAL INJURY, ATLASIED SHALL NOT BE LIABLE IN TORT OR CONTRACT
FOR ANY DIRECT, CONSEQUENTIAL OR INCIDENTAL LOSS OR DAMAGE ARISING OUT OF THE
INSTALLATION, USE OR INABILITY TO USE THE PRODUCTS. THE ABOVE WARRANTY IS IN LIEU OF
ALL OTHER WARRANTIES INCLUDING BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE.

AtlasIED does not assume, or does it authorize any other person to assume or extend on its behalf,
any other warranty, obligation, or liability. This warranty gives you specific legal rights and you may
have other rights which vary from state to state.

Service

Should your Atlas TSD require service, please contact the AtlasIED

warranty department at 1-877-689-8055, ext. 277 to obtain an RA number.

AtlasIED Tech Support can be reached at 1-800-876-3333 or support.atlasied.com.

Visit our website at www.AtlasIED.com to see other Atlas products.

©2017 Atlas Sound L.P. The Atlas “Circle A”, Soundolier, and Atlas Sound are trademarks of Atlas Sound L.P.

All other trademarks are the property of their respective owners. All specs are subject to change without notice. ATS004403 RevF 4/17

AtlasIED.com – 16 –

IED is a registered trademark of Innovative Electronic Designs LLC. All Rights Reserved.

1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A.

Telephone: [phone] • Fax: [phone]

Specifications are subject to change without notice.