ECM-2063
AC Power Distribution Sequencer Raceway System
Features
• Compact design 37”H x 3.5”W x 2.75”D
• 6 Separate 120V Outlet Sections
• 12, 120VAC 20A Outlets
• Accepts up to 3 20A 120VAC Lines, Configurable
• Incoming AC present LED
• Active LED
• Remote or Local Activation
• Latching Contact Closure Trigger
• 6 Dual Knockouts 1⁄2” & 3⁄4”
• 4 Rail Mounting Tabs
Application
The Atlas Power ECM-2063 was designed to be flexible, incorporating
features that allow it to be used in a variety of applications. The
sequenced outputs allow equipment to be turned ON or OFF in a
particular order. This prevents an in-rush of current that could potentially
damage connected electronics and eliminates audible pops that often
occur with non-sequenced power activation. The following are just a few
examples of applications in which the Atlas Power ECM-2063 can be
used:
• Restaurants
• Houses of Worship
• Schools
• Office Buildings
• Sports Bars
• Industrial Facilities
General Description
The Atlas Power ECM-2063 AC Power Distribution Sequencer Raceway
System is designed to offer the installer/contractor current requirement
flexibility based on the needs of the equipment that will be connected to
the raceway. The ECM-2063 accepts up to three separate 20A 120VAC
lines, allowing for up to a total of 60A to be divided throughout the
system. The ECM-2063 features 6 individual AC 120V outlet sections that
can be activated individually or in a sequenced order. Triggering a section
or sequential order can be accomplished via a remote switch or by using
a sequence controller like the Atlas Power TSD-SEQ6 or ECS-6RM.
The ECM-2063 features a total of 12, 120VAC outlets that are divided
into 6 sections. Each section has an activation control port and a bi-color
LED. This LED will display green to indicate that AC voltage is present at
that specific AC section when it is activated or triggered and the LED will
display red to indicate that the section is in Stand-By mode. Activation is
easy, simply short the two pins of the control port for the specific channel
you want triggered ON. This can be accomplished within a few feet of the
ECM-2063 or from several feet away by using an Atlas Power sequence
controller or via a switch.
The ECM-2063 was designed to be compact measuring only 37” high,
3.5” wide and 2.75” deep. The ECM-2063 can be mounted into most
racks that have 48” internal height. The raceway can be mounted using
the raceway mounting tabs which are designed to breakaway if needed
to fit into tighter areas making it adaptable to secure the raceway in most
applications. For convenience there are six 1⁄2” & 3⁄4” dual knockouts
that support standard electrical conduit components for wiring 120VAC
mains into the raceway housing from the electrical panel.
©2012 Atlas Sound L.P. All rights reserved. Atlas Sound and Strategy Series are trademarks of Atlas Sound L.P. All other trademarks are the property of their respective owners. ATS004503 RevA 8/12
1601 JACK MCKAY BLVD. ENNIS, TEXAS 75119 U.S.A.
TELEPHONE: (800) 876-3333
FAX (800) 765-3435
AtlasSound.com
1/2
Specifications
Front Panel
Number of Channels 6
AC Outlets 12 NEMA 5-20, Switched
Connectors Qty 6, 2 Position Phoenix Euro Block Style
3.5mm Spacing
Remote Trigger Latching Contact Closure
Indicators Incoming AC (Red), Active (Green)
AC Mains Interconnect Screw Terminal Block
Technical Data
Voltage 120V AC, 60Hz
Load 20A + 20A + 20A Congurable
Power Consumption 5.1W Standby, 11.3W Active
Mechanical
Chassis Finish Black Paint
Mounting Rail Tabs
Electrical Inlets 6 - Duplex
Electrical Inlet Size 0.50" and 0.75" Dual Knockout
Height 2.59" (65.79mm)
Width 3.26" (82.80mm)
Length 36.84" (935.74mm)
Weight 10 lbs (4.54kg)
Architect & Engineering Specifications
Power distribution sequencer raceway shall be Atlas Sound model
ECM-2063. Unit shall have a total of 12 NEMA 5-20 switched outlets in
three 20A sections. Raceway shall connect to AC Mains via screw
terminal block. Terminal block shall allow for 20A congurable set-up
including three 20A circuits with 4 outlets in each circuit, one 20A circuit
with 8 outlets and one 20A circuit with 4 outlets, or one 20A circuit with
12 outlets. Unit shall feature a remote trigger contact closure connection
for each 2 position connector allowing for remote turn Off/On of each
outlet section via Atlas Power controller, ECS-6RM or TSD-SEQ6, remote
key, or push button switch. Unit shall feature incoming AC and active
outlet LED indicators.
Unit shall be rack mountable via included rail tabs and shall include 6
electrical inlets for connection to AC mains. Finish shall be textured black
epoxy and dimensions shall be 2.59" (65.79mm) x 3.26" (82.80mm) x
36.84" (935.74mm). Unit will be RoHS compliant and have ETL safety
listing to UL60065 standard.
RoHS Compliant Yes
Safety Listing ETL (UL60065 Standard)
©2012 Atlas Sound L.P. All rights reserved. Atlas Sound and Strategy Series are trademarks of Atlas Sound L.P. All other trademarks are the property of their respective owners. ATS004503 RevA 8/12
1601 JACK MCKAY BLVD. ENNIS, TEXAS 75119 U.S.A.
TELEPHONE: (800) 876-3333
FAX (800) 765-3435
AtlasSound.com
2/2
Loading...