Atlas IED 735-25, 740-25, 744-25, 744-30, 744-36 Installation Manual

700 Series Racks

Isolating Rack from Semi-Conductive Surface

AtlasIED 700 Series equipment racks are constructed using the highest quality Cold Rolled Steel (CRS) and are designed to be durable for long
term use. In some installations where the rack is positioned on or secured to a semi-conductive surface like concrete or raised panels noise can be
introduced into the system through the floor surface and / or the mounting bolts securing the rack to the surface. Isolating washers can be used in
these instances to isolate the rack from the surface and / or mounting hardware.

Floor Mounting 700 Series Rack with Isolation

Each 700 Series rack includes two holes in each corner that can be
utilized to secure the rack to the mounting surface. Consult the 700
Series installation sheet for recommendations. Bolts may be either
drilled and inserted into the floor and then secured from the top with a
nut or holes can be pre-drilled and the bolts can be secured once the
rack is in position.

A non-conductive isolating washer as well as a non-conductive mat
must be used to isolate the rack from the mounting surface. Once the
mounting holes are drilled in the surface, position the isolation mat and
remove the mat material so the mounting bolts can pass through the
mat into the surface.

AtlasIED recommends the Essentra Components 10SC312037 isolating
shoulder washer in combination with a 5/16" mounting bolt. Isolation mats
are available in a number of sizes from a number of manufacturers.
Consult the system designer for recommended mat thickness.

5

/16" Mounting Bolt (Not Included)

Isolating Shoulder Washer (Not Included)

Rack Bottom

Isolation Mat (Not Included)

©2019 Atlas Sound LP. The Atlas “Circle A”, Soundolier, and Atlas Sound are trademarks of Atlas Sound L.P. IED is a Registered Trademark of Innovative Electronic Designs LLC. All rights reserved.

All other Trademarks are property of their respective owners. No endorsement is implied. Due to continual product development, specifications are subject to change without notice. ATS005996 RevA 6/19

1601 JACK MCKAY BLVD.
ENNIS, TEXAS 75119 U.S.A.

TELEPHONE: [phone]
[e-mail]

AtlasIED.com

Floor Mounting 700 Series Rack with Isolation and

Seismic Bracket

Each 700 Series rack includes two holes in each corner that can be
utilized to secure the SBK-700 seismic brack and rack to the mounting
surface. The SBK-700 enables a 700 Series rack to be certified in
accordance to the Telcordia NEBS (Network Equipment Building
Systems) GR-63-CORE standard. Each seismic bracket mounts in
each corner of the rack. Consult the 700 Series installation sheet for
recommendations on preparing the surface. Bolts may be either drilled
and inserted into the floor and then secured from the top with a nut or
holes can be pre-drilled and the bolts can be secured once the rack is in
position.

A non-conductive isolating washer as well as a non-conductive mat
must be used to isolate the rack from the mounting surface. Once the
mounting holes are drilled in the surface, position the isolation mat and
remove the mat material so the mounting bolts can pass through the
mat into the surface.

AtlasIED recommends the Essentra Components 10SC312037 isolating
shoulder washer in combination with a
are available in a number of sizes from a number of manufacturers.
Consult the system designer for recommended mat thickness.

5

/16" Mounting Bolt

(Not Included)

Isolating Shoulder
Washer (Not Included)

5

/16" mounting bolt. Isolation mats

©2019 Atlas Sound LP. The Atlas “Circle A”, Soundolier, and Atlas Sound are trademarks of Atlas Sound L.P. IED is a Registered Trademark of Innovative Electronic Designs LLC. All rights reserved.

All other Trademarks are property of their respective owners. No endorsement is implied. Due to continual product development, specifications are subject to change without notice. ATS005996 RevA 6/19

SBK-700

1601 JACK MCKAY BLVD.
ENNIS, TEXAS 75119 U.S.A.

TELEPHONE: [phone]
[e-mail]

AtlasIED.com